Search Documents

By J. Drelich

We report structural forces measured for 10 nm silica particles deposited on alumina substrate and 5-80 nm alumina particles on mica using atomic force microscopy technique. For nanoparticles forming clusters, oscillation of structural forces was recorded with a periodicity that is close to the size of the nanoparticles used. Additionally, selected force-separation results indicate that the forces involved between the AFM probe and individual nanoparticles can be studied using the nanoparticle-coated substrates.

Jan 1, 2006

By C. Bernier

This paper deals with three major problems associated with mining operations during the winter. These are the maintenance of the cooling systems of diesel engines, the high incidence of hydraulic dump failures on packaging machines, and the build-up of frozen fines on wet-ore conveyor belts.

Jan 1, 1966

By R. J. Smyth

A Steel Compression Reinforcement Repair Technique (PetroSleevel) system has been developed that has the ability to repair pipeline defects such as stress corrosion cracking (SCC) without requiring welding to the operating pipeline. The Technology has been used to repair active cracking in ERW seam and cracking in the pipe body. All repairs were performed while the pipeline was in operation. This paper will discuss the engineering theory, testing performed to verify the engineering theory, and examples of actual sleeve installations.

Jan 1, 2005

By Chris Carr

This paper describes the process employed and the work undertaken to enable the surrender of the mine permit relating to the two tailings deposits at the abandoned Red Mountain Mine site near Rossland, BC. The first phase of the work undertaken was to provide urgent remedial work for protection of the environment, primarily through rehabilitation or replacement of surface water drainage systems. The second phase was to up-grade the water management systems to the appropriate level given their consequences of failure. The final phase of work is to ensure long term geotechnical stability of the facilities to the same level of risk. Establishment of a sustaining fund will facilitate long term monitoring and maintenance of the facilities.

May 1, 2002

By D. K. Sarkar, Jiawei Xiong

"Self-assembled monolayers (SAM) on the aluminum substrates are used as the adhesion promoter between two aluminum substrates when bonded with the adhesive in adhesive bonding technology. Traditional surface analysis tools are not capable of identifying the presence of SAM on a surface; therefore, EIS has been used to determine their presence on the aluminum substrates. In this study SAMs have been deposited on aluminum using the monomer of (3-Glycidyloxypropyl)trimethoxysilane (GPTS) organosilane. AA6061 aluminum alloys substrates were chemically cleaned with NaOH and HNO3 to remove the native oxides, followed by immersion in silane solutions. In a second method, SAMs were prepared by applying a spin coating of silane solution to the samples. The prepared SAM coated aluminum samples were analysed by EIS in the three electrode corrosion cell using a diluted alkaline solution. The impedance of the SAM coated aluminum is found be higher than the as-received aluminum. It has been also observed that the open circuit potential (OCP) of the SAM coated aluminum is higher than the as-received aluminum. Both elevated values of the impedance and OCP confirm the presence of SAM on aluminum.INTRODUCTIONSelf-assembly (Schreiber, 2000) is defined as the spontaneous formation of complex hierarchical structures from pre-designed building blocks, typically involving multiple energy scales and multiple degrees of freedom. Generally speaking, SAMs are created by the chemisorption of ""head groups"" onto a substrate from either the vapor or liquid phase followed by a slow organization of ""tail groups"" of a molecule. Typically, head groups are connected to a molecular chain in which the terminal end can be functionalized with groups such as –OH, –NH2, –COOH, or –SH to vary the wetting and interfacial properties (Chauhan et al., 2007; Ulman, 1996; Vashist, Lam, Hrapovic, Male, & Luong, 2014). Though there exist several methods to prepare SAM (Chauhan et al., 2007; Chen, Yang, & Zhang, 2014; Cho, Park, Jon, & Choi, 2007; Igor Luzinov, 2000; Reis, de Melo, & Costa, 2006; Song, Zhai, Wang, & Jiang, 2006; Sugimura, Hozumi, Kameyama, & Takai, 2002; Vashist et al., 2014), the two methods vapor phase (Song et al., 2006; Sugimura et al., 2002) and solution(Chen et al., 2014; Igor Luzinov, 2000) are commonly used. Recently, many articles have been published on the fabrication of superhydrophobic surfaces with SAM technology (Cho et al., 2007; Pan, Shen, Shang, & Xing, 2012; Siddaramanna, Saleema, & Sarkar, 2014; Song et al., 2006). Brassard, Sarkar, and Perron (2011) successfully obtained a superhydrophobic film by applying fluoroalkylsilane via self-assembly on monodispersive silica. SAMs are also reported as good candidates for anti-corrosion and adhesion promotion (Chen et al., 2014; Saleema, Sarkar, Paynter, Gallant, & Eskandarian, 2012). However, papers on the characterization of SAM properties are rarely seen. The most commonly used substrate for SAM is silicon and the method implemented is scanning probe microscopy (SPM) such as atomic force microscope (AFM) (Igor Luzinov, 2000; Moores, 2011; Zhang, 2003, 2005). Igor Luzinov (2000) analyzed the epoxysilane SAMs’ surface morphology and microstructure properties using scanning probe microscopy (SPM) and ellipsometry on single-crystal silicon wafers. SAMs have been used to improve the adhesion bonding of aluminum or plastics but no characteristic data have been presented yet (Saleema et al., 2012; Telegdi, 2007; Wang, Xu, Luo, Wang, & Wang, 2009). Recently, Reis et al.(Reis et al., 2006) have studied SAM of alkane diphosphonate (Gardobond X4661) on Al 5052 alloy samples by EIS in a naturally aerated sodium sulfate solution."

Jan 1, 2016

By R. W. Diamond

Introduction THE Sullivan mine and the milling, smelting, and refining operations of the Consolidated Mining and Smelting Company are sufficiently well known to make unnecessary anything more than a very brief account of the events which led up to this Company's branching out into the chemical industry. This development is the result of the 26 per cent sulphur content of the Sullivan ore. Seventy-five to eighty per cent of this sulphur enters the mill tailing, which is stocked at Kimberley. The remainder, contained in the lead and zinc concentrate, is burned off in the first treatments at Trail. Prior to this new development, the sulphur gas was wasted to the atmosphere. In spire of its great dilution with air and discharge from stacks at high elevations above the plant, some damage to vegetation close to the plant was experienced. It had always been apparent that this sulphur should be recovered and utilized if possible, at the same rime relieving, or curing, the smoke nuisance, and constant studies with this in view had, therefore, been maintained. One of the early conclusions reached was that the Canadian prairies would ultimately require large quantities of phosphate fertilizers, as had been the experience of older countries, and that these fertilizers would constitute a large outlet for sulphuric acid which could be made from smelter gases. This conclusion prompted a widespread search for phosphate rock, particularly in British Columbia and western Alberta, with the result that low-grade beds were discovered in the Crowsnest district and to the north therefrom through extensive areas (1). Following these discoveries, an experimental plant was built at Trail for the production of triple superphosphate in order to facilitate field-tests in fertilizing prairie lands.

Jan 1, 1934

By C. Boudreault, M. Fortier, S. Fafard

In the forging industry, the increasing trend is to use DC cast billets as forging stock to replace extruded stock. However, there is little technical information available in open literature. In order to gain a better understanding of the behaviour of cast stock during deformation, a study was initiated to evaluate the impact of an homogenisation treatment on the billet prior to cold forging. Axisymmetric upsettings of cylindrical samples machined from DC billets were achieved in order to evaluate and compare flow stresses, crack initiation and propagation. Results show a 30% decrease in flow stress after homogenisation. Observations of the deformed samples show major cracking for the as-cast material. Optical microscopy and SEM observations have related the crack initiation to decohesion around ß -AlFeSi particles and subsequent growth along the constituent path. Homogenisation effectively breaks up and transforms the ß phase, present as platelets in the cast product, into smaller spherodised a-AlFeSi particles. This has the effect of preventing crack growth in the forged product. The homogenisation treatment also resulted in the reduction of Mg and Si in solid solution. The softer matrix generated 29% less die wear when compared to the as-cast structure. Based on the results of this study, it is thus recommended to homogenise cast billets prior to cold forging.

Jan 1, 2006

By H. Zhu, Y. Sato, O. Takeda, K. Nakano

Recycling of rare earth magnet wastes is essential to insure the stable supply of rare earth resources. For the development of a novel recycling process, the removal of rare earth oxide from an off-spec alloy magnet was investigated by melting the alloy magnet at 1503 K together with fluoride flux, LiF-50 mol% NdF3 and LiF-?25 mol% NdF3-25 mol% DyF3. After melting, the separation of magnet alloy from the fluoride flux was achieved, and neither suspension of alloy in the flux nor suspension of flux in the alloy was observed. Oxygen concentration in the alloy decreased from 5000 mass-ppm to 160 mass-ppm by utilizing 1.5 times of equivalent amount of flux needed to completely dissolve the oxide. The investigated process is suitable for mildly contaminated waste such as a used (end-of-life) magnet because of its simplicity, low energy consumption and small limitation on location for operation.

Jan 1, 2014

By Gil Espejo, Denise Duncan

"In Alberta, several initiatives are under way to form partnerships between educators and industry to work together in preparing a skilled and technically competent workforce for the future. One successful initiative is the Teachers in Business program which provides high school teachers one month paid internships in Alberta businesses. Initiated by the Science Alberta Foundation in 1992, this program has offered participating teachers a variety of work experiences and job shadowing tours in industry.A Growing Need of Education and Industry PartnershipsIn our ever evolving world, industry is in a tight race to keep up to date with new technology and to remain competitive. Industry is relying on the education system to provide them with the core base for their future workforce. To accomplish this, the education system needs the support of industry to develop the right focus to prepare its students for the race. What skills will our future workforce need? How can we best prepare our students for these needs?Teaching the latest in technology, especially at the high school level, is a major challenge. It is difficult for educators to keep abreast of the rapid changes in technology. High school graduates need exposure to the latest advancements. And so do their teachers. Students must be prepared to adapt to the challenges of the future, Le. global competition, rapid technological change and an expanding knowledge base."

Jan 1, 1995

By J. F. Dorion

This paper presents the results of on-going investigations on the performance of support systems in Québec underground mines. The focus of these investigations is on site observations complemented by laboratory investigations. Of particular interest is deducing the corrosion rate, at selected mine sites, as determined by the installation of monitoring coupons.

May 1, 2009

By Ahmad Ghahreman, Lin Li

"In this study, the Fe(II)/Fe(III) redox reaction kinetics on the surface of pyrite, have been investigated in a 0.5 mol L-1 sulfuric acid solution for a temperature range of 22 to 65°C. Based on mixed potential theory, chronoamperometry is introduced to study the Fe(II)/Fe(III) kinetics by subtracting the current density of pyrite oxidation in an iron-free acidic solution from that in an iron-containing solution at the same applied polarized potential. Tafel behavior was established by this method to analyze the kinetics of the Fe(II)/Fe(III) redox reactions. The results showed that exchange current densities increased slightly with temperature, however remained on the order of 10-5 A cm-2. The activation energy for Fe(II) oxidation and Fe(III) reduction on the pyrite surfaces was calculated to be 102.0 and 32.7 kJ mol-1, respectively. Anodic transfer coefficients also increased, from 0.24 to 0.39, with increasing temperature, which indicates a weakened n-type semiconductor property at higher temperatures. Electrochemical impedance spectroscopy measurements have indicated that at lower anodic over potentials the charge transfer is the rate determining step of pyrite oxidative dissolution in sulfuric acid solution. In the presence of Fe ions, the major contribution of the total current density comes from the Fe(II)/Fe(III) redox reaction. INTRODUCTION Pyrite, an abundant sulfides mineral in the nature, is commonly considered a valueless gangue mineral frequently associated with other valuable sulfide minerals such as chalcopyrite, or metals such as gold, or coal (Lin & Say, 1999). Pyrite oxidation has been the subject of extensive research in view of gold metallurgy, as oxidation of pyrite is the initial step to break down the pyrite lattice and expose the encapsulated fine gold particles (Gasparrini, 1983). Fe(III) ion and dissolved oxygen (DO) have generally been considered as the two most important oxidants with respect to pyrite oxidation, having been studied extensively in previous research (Zheng, Allen, & Bautista, 1986; King Jr & Lewis, 1980). The process of pyrite oxidation can be viewed as a series of reactions amongst pyrite, ferrous, ferric and oxygen in which pyrite is initially oxidized by the dissolved oxygen in water forming ferrous (Eq. 1), and then the ferrous also is oxidized by he dissolved oxygen to form ferric (Eq. 2). The ferric, produced by reaction 2, then could potentially oxidize pyrite (Eq. 3) and convert to ferrous."

Jan 1, 2017

By P. J. van Staden

Several differences exist between the columns used for laboratory simulations of heap leaching and commercial heaps. Column walls support part of the weight of the ore and restrict the particle packing arrangements. Columns are typically of a diameter that is smaller than the dripper spacing to be used on the commercial heaps. The stacking practices that cause segregation and stratification on heaps are absent from columns. Intuitively, these physical differences would be expected to be the reasons behind the observed differences between column and heap leaching performance. But how can they be quantified, and what is the magnitude of the differences? Could some of these differences be built into column leaching experiments in order to better simulate commercial-scale heap leaching performance to ease the scale-up calculations from column leaching data? Alternatively, could heap construction practices be improved so that the ideal performance obtained in columns could be emulated on heaps? Data from a few heap leaching cases studies that permit direct comparisons between column and heap leaching performance is analysed, to reveal the extent of the differences in resistance to mass transfer. Discussion is provided on the implications for column and heap leaching practice, and for scale-up design procedures. INTRODUCTION Differences have been known to exist between leaching performance observed in laboratory columns and that of commercial-scale heaps. Both the heap leaching kinetics and finally achievable extent of extraction are generally found to be inferior in heaps compared to that achieved in columns. Heap leaching design engineers extrapolate the anticipated heap leaching performance by multiplying the time-axis of a column-leaching curve by a factor of about 2 and the extraction-axis by a factor of about 0.8, as explained by Jansen and Taylor (2002), Scheffel (2002), John (2011) and Scheffel, Guzmán, and Dreier (2016). The procedure is illustrated in Figure 1 by means of a hypothetical example. The solid line represents the leaching performance observed in a laboratory column, and the dashed line represents the anticipated leaching performance of a heap, extrapolated from the column leaching data using these empirical scale-up factors.

Jan 1, 2019

By David Minson

On many occasions, operators have seen that high density and paste thickener performance does not meet the initial design expectations, and the installed equipment produces lower than expected thickener underflow solids content. This lower-density tailings slurry leads to more water and lower beaching angles being seen at the tailings storage facility (TSF). This not only reduces storage capacity, but also increases the risks of non-compliance with environmental permit constraints. Reasons for the shortfall in performance can be many, but perhaps the main problem is inadequate understanding of the critical components of thickener design and operation, with too much reliance placed on standardised design terminology; such as tph/m2. This paper discusses additional factors that influence high-density thickener operation and presents test work that defines “Dynamic Slurry Fluidity”, “Bed Compaction Rates”, and “Natural Slump Angles” for these high yield stress/viscosity slurries. Finally, the paper uses this data to define thickener geometry, drive torque, floor slope(s), rake blade configuration and how this can be used to provide engineers with more tools for in depth evaluation of a High-Density thickener design. INTRODUCTION Generally copper mines are high tonnage operations, with copper flotation concentrators producing high volumes of tailings slurries of milled solids and water. As a result, Tailings Storage Facilities (TSF) become very large and this, along with potential scarcity of water, favours a design that maximises storage space. In theory, the use of filtration equipment that achieves immediate water recovery, high TSF in-situ densities and high stacking angles are preferred for this duty. However, large tailings filter units are uncommon, and have high operating and capital costs that favour the use of thickeners. The use of high-density thickeners to produce a thick or near-paste like slurry with high un- sheared yield stress values above 100 Pascals, is becoming more common. The higher thickener underflow is required to not only maximise water recirculation within the mill, but to also increase beaching angles, maximise tailings storage capacity and minimise evaporation losses arising from large areas of superficial water. However, the reliability of this equipment is also under scrutiny and there is perhaps a need to better define these designs.

Jan 1, 2019

By A-A. Bogno, Ch. -A. Gandin, A. Maitre, H. Henein

Most metallic materials are produced from their liquid state. In order to control the properties of industrial products, it is very important to understand their solidification path and the resulting microstructures which can be significantly affected by melt undercooling. High undercooling results in rapid solidification and a refined microstructure with minimal microsegregation. This paper reports on the analysis of rapidly solidified Al-Cu droplets obtained by a single fluid atomization process, Impulse Atomization. A quantitative analysis by Rietveld refinement method of the Neutrons Diffraction data was carried out to determine the fraction of the intermetallic Al2Cu. Knowing the fraction of Al2Cu, the eutectic fractions and corresponding dendritic and eutectic undercoolings were estimated using the metastable extensions of solidus and liquidus lines of the Al-Cu system calculated by Thermo-Calc. In addition to this work, a model of microsegregation coupled with ThermoCalc software via TQ (application programming interface of ThermoCalc) and the Wang-Beckerman model for dendritic growth velocities has been developed for binary alloys. This has led to the development of a phenomenological relationship between primary phase undercooling and initial growth velocity. A comparison of estimated primary undercoolings using a coarsening model with the adiabatic undercoolings for each alloy composition has confirmed that solidification occurs under adiabatic conditions during recalescence.

Jan 1, 2014

By Y. W. Pan, Y. R. Liu

The disturbed natural rock mass tends to equilibrium state accompanying with non-equilibrium evolution process which has significant influence on the long-term stability of engineering structure. The deformation development in the non-equilibrium evolution is determined by two intrinsic processes, trend to equilibrium and damage development, which can be illustrated by evolution of excavated tunnel. Thus the creep and damage must be taken into account in study of non-equilibrium evolution process. Within Rice’s irreversible thermodynamics with internal state variable (ISV), the conjugate force function which equals to zero is a convex surface which divide the stress space into two parts, called equilibrium and nonequilibrium stress space respectively. The concept of effective stress of non-equilibrium has been proposed, in which the stress difference (d - d ) are the effective driving forces of non-equilibrium evolution process with hardening and damage effective. The formulations of inelastic strain rate and energy dissipation rate have been recast in the form of effective stresses. The inelastic complementary energy (ICE) is proposed to measure intensity of non-equilibrium evolution of material system. The specific equations of conjugated forces and kinetic equations of internal state variables are presented. The ICE and rate of energy dissipation are all calculated to be used to evaluate long-term stability of geo-engineering. The results show that rate of energy dissipation may be more convenience and flexible than ICE for internal state variable constitutive equation of rock mass.

Jan 1, 2015

By D. R. Keck

"SINCE the .Canadian Chemical Company has no direct connection with mining operations, and I have had no experience with mining, there is little I can tell you that you do not already know. However, we have had considerable experience with certain types of metallurgical problems and I would like to discuss with you some of these problems and their solutions by our metallurgists.In order to acquaint you with the type of plant and processes to be employed at Edmonton, I would like first to take a few .minutes to trace briefly the history -of the Canadian Chemical Company's affiliate, The Celanese Corporation of America. In the early •part of the twentieth century, two young Swiss brothers, Camille and Henri Dreyfus, received their P.h.D. degrees in chemistry. They were extremely interested in work which was being carried on at that time to find a suitable synthetic fiber that could compete with natural fibers, both quality and price-wise. Early man-made fibers were both coarse and hard to dye. The Doctors Dreyfus• poured all their earnings into research and ultimately developed cellulose acetate filament. During World War I, the Dreyfus brothers were invited to the United States to produce cellulose acetate 'dope' for airplane wing coverings. Dr. Camille Dreyfus built the first American plant for fiber production at Cumberland, Maryland, in 1924.Due to resistance of textile mills to the new fibers, Celanese was forced to set up its own dying, weaving, and finishing mills to prove the new materials. Through the years, however, this operation has •been retained primarily for fabric development purposes,.. with the majority of the acetate being sold to other textile mills."

Jan 1, 1953

By Scott Hommema

? Bitumen in the oil sand averages Bitumen 12 wt%; water makes up 4 wt% ? Imperial Oil (operator) and ExxonMobil developing Kearl Leases #6, 36, 87 (~200 sq. km) ? Target resource > 4 Billion Barrels ? 3 Phase development, ~100 kbd per phase High-quality resource ? Surface mineable bitumen ? Average properties (full lease) ? TV:BIP < 8 ? Grade > 12 wt% bitumen ? Ore thickness of 40 m ? Overburden thickness of 20 m Status ? Phase 1 ? Front end engineering and design underway ? Detailed engineering to start 2008

May 1, 2008

By L. H. Van Loon, E. G. Crayston, A. F. Heather

"IntroductionTHE PROPERTY of Madsen Red Lake Gold Mines. Limited. comprises fifty-eight claims located between Russet and Faulkenham lakes in Baird and Heyson townships of the Patricia portion of the District of Kenora. The mine is seven miles •by road from the hamlet of Red Lake. This latter centre is .connected to the Trans-Canada Highway at Vermillion Bay, Ontario, by provincial highway No. 105 which has a total length of one hundred and thirteen miles.The Madsen property went into production on August 11th, 1938, with a milling plant rated at 300 tons per twenty-four hours. Changes made in the crushing plant during October, 1938, allowed a •finer feed to be delivered to the mill and increased the milling •capacity to 400 tons per twenty-four hours. During 1948, steps were taken to add an additional 400-ton capacity unit to the milling plant. This latter work was completed by May, 1949, giving the present total milling .capacity of 800 tons per twenty-four hours.It was realized in the early 1940's that, eventually, considerable material suitable for backfilling in the mine would be required. As there were no large deposits of gravel or sand anywhere near the mine, officials of the Company considered it advisable to investigate the feasibility of using mill tailings for mine •backfill. Since Madsen mill tailings contain approximately 80 per •cent of minus-200-mesh material, it was not considered practical to use them for underground backfill without first removing the finer material. as the slimes present in a product of this fineness would without doubt preclude any drainage whatsoever. Table I gives a sizing analysis of Madsen mill tailings and Table II a quantitative chemical analysis of the ore."

Jan 1, 1954

By K. Schimann, H. D. Knipping, J. P. Fouques

"RESUMELe gisement d &apos;uranium de Cigar Lake, dans la région de l&apos;Athabasca au nord du Saskatchewan, fut découvert en mai 1981 par Cogema Canada Ltée, opérant pour Ie compte de la ""Waterbury Lake Joint Venture"".Le corps minéralisé. qui est dépourvu de toute expression directe en surface, est situé a la discordance entre les met sédiments du wottaston Group (Protérozoïque inférieur ou Aphébien) et les grès de l &apos;Athabasca (Protérozoïque moyen ou Hélikien), à une profondeur de 410 a450 m.Fin 1984, Ie gisement était reconnu par 105 sondages minéralisés repartis sur une longueur de 1800 m, pour une largeur comprise entre 25 et 105 m. 11 se présente sous forme d’une lentille aplatie de 5 a30 m de puissance, et montre une remarquable continuité d&apos;ensemble. Une ride ou bombement topographique de la discordance est associée au gisement surtoute sa longueur.A l&apos;échelle régionale, le corps minéralisé à est associe à un corridor structural d’orientation est-ouest, a l&apos;intérieur duquel des facies particuliers aténdance blast mylonitique sont développes dans les formations métapolitiques agraphite du socle métamorphique. Il est entouré par un halo d&apos;altération très important, caractériser Ie développement de minéraux argileux alumino-magnesiens (illite-chlorite).La minéralisation est située, pour la plus grande part, dans les grès d&apos;Athabasca, et se compose essentiellement d&apos;uraninite et de sulfo-arseniures de nickel et de cobalt,De nombreux levés géochimiques et géophysiques ont été effectues dans la région de Cigar Lake. Aucune anomalie ne peut être associée directement au corps minéralise, mais la combinaison des données en provenance de plusieurs sources s’est révélée fort utile au niveau de l’interprétation géologique régionale et de la définition des cibles de sondages a l&apos;intérieur des zones reconnues favorables.Le gisement de Cigar Lake présente de nombreuses analogies avec plusieurs des gites classiques de la région de l&apos;Athabasca; il est caractérise en particulier par l&apos;intensité des phénomènes d’altération et la présence de minéralisations extrêmementriches.En 1984, les réserves géologiques globales estimées par géostatistique sur I ‘amas minéralise principal s &apos;élevaient a 110 000 tonnes d&apos;uranium, aune teneur moyenne de 12.2%, avec une précision de 25% à l&apos;intervalle de confiance de 95%.ABSTRACTThe Cigar Lake uranium deposit, in the Athabasca area of North Saskatchewan, was discovered in May 1981 by Cogema Canada LId., as operator of the Waterbury Lake Joint Venture. The deposit, which is devoid of direct surface expression, is located at the unconformity between the Lower Proterozoic (Aphebian) Wollaston Group meta-sediments and the Middle Proterozoic (Helikian) Athabasca sands tone, at a depth of 410 m to 450 m below surf ace.AI the end of 1984, the deposit had been defined by 105 mineralized holes over a length of 1800 m and a width of between 25 m and 105 m. It has the shape of a flat-lying lens 5 m to 30 m thick and shows a remarkable longitudinal and latera continuity from the information obtained to date. A well-defined bulge of the unconformity underlies the mineralized zone over its entire length.The deposit appears to be controlled by an east-west-trending structure within which a particular rock facies (""augen gneiss"") has developed in the graphitic metapelites of the Wollaston Group. It is surrounded by a strong alteration halo affecting both sandstone and basement, characterized by extensive development of Mg-A I rich clay minerals (illite-chlorite).The mineralization is hosted principally by the Athabasca sandstone, and consists mainly of uraninite and sulfo-arsenides of nickel and cobalt.Numerous geochemical and geophysical surveys have been carried out in the Cigar Lake area, and no specific geochemical or geophysical anomaly can be directly associated with the mineralized body, although there may be locally a good coincidence. However, a combination of several methods proved extre"

Jan 1, 1986

By G. K. Quainoo

Investigation by researchers on the application of various thermo-mechanical process histories on 6000 series aluminum alloys have found improvements in mechanical properties of these alloys. However, natural aging, which is unavoidable in the automotive processing line, has been found to have deleterious effect on subsequent artificial aging properties in these alloys. In this study, the evolution of yield strength during natural aging modeled by Lloyd and Gupta has been adapted to investigate the effect of cold deformation on the natural aging kinetics in AA61 11 by means of tensile testing, differential scanning calorimeter (DSC) and scanning electron microscopy (SEM). Also, intermetallic particles in the alloy were extracted from the matrix and XRD performed on them to ascertain their composition and their role on the kinetics in the alloy. The results show that cold work effect on the natural aging kinetics of AA6111 is in very good agreement with the model proposed by Lloyd and Gupta. The kinetics of natural aging in AA6111 aluminum also decreases with increasing level of cold work. This is attributed to dislocations serving as sinks which consume quenched-in vacancies formed during the early stages of clustering. The phases of the intermetallic particles identified in AA6111 are those of a-A15Mn12Si7 and a-A15MnSi.

Jan 1, 2007