Search Documents

By W. M. G. Heeley

In the province of Alberta the coal measures dip at so many different angles, between the horizontal and the vertical, that many different systems of haulage are in use. I will, however, only touch briefly upon the general -systems in use, and devote the major portion of this paper to a discussion of endless-rope haulage and its adaptibility to various conditions in coal mines; dealing in particular with the endless-rope haulage that was installed at Brule during the month of August 1923. In coal seams that are approximately level, and newly opened, hand-putting or tramming from the face is the cheapest, but when the mine is further developed tramming is out of the question, and the use of ponies is the next consideration. The time arrives, however, when mining reaches a point where the economical haulage of coal by horses cannot be done profitably, and then some system of mechanical haulage must be installed. The installation of any system should be carefully considered before any particular type of haulage is adopted, because a great deal depends upon the grade or dip of the seam. Motor haulage is impossible to operate profitably on a grade of over 6 per cent and, while it is possible to use ponies, on short runs, up to 9 per cent, some other means of main and secondary haulage must be installed when a 9 per cent grade, is exceeded. I will, therefore, deal first with secondary haulage, because even though a main haulage is established, secondary haulage can be used to feed the main haulage.

Jan 1, 1925

By A. Noël, R. Lapierre, M. Provencher

"Modem aluminum smelters are facing significant operating cost pressure. Key methods used by smelters to manage this pressure are automation and production-information systems to optimize processes, manage quality, anticipate problems and reduce operating costs. In 2002, Aluminerie Alouette Inc. began its Phase II Expansion project, and retained the joint venture of SNC-Lavalin and Hatch (SLH) as its engineering, procurement and construction management (EPCM) team. Alouette had the distinction of being one of the most efficient aluminum smelters in the world. Alouette already understood the importance of systems integration in project delivery. For Phase II, key objectives were identified to ensure ""a state of the art"" integrated architecture that would support Alouette's production goals to integrate the existing facilities with the expansion, to form a single efficient facility and meet project schedule and budget targets. Achieving those objectives within the context of a large project often creates major challenges due to the nature of the traditional EPCM delivery model, which relies on several vendors and third-party-systems integrators. In this case, an integrated Alouette-SLH team was made responsible for all aspects of the systems integration, taking over the task from most suppliers. The integrated team was responsible for delivering an automation system and plant-wide-production IT system for the new facilities while accommodating migration for the existing systems. Through the use of rigorous methodology and advanced state of the art technology, the IT and automation strategy led to significant value creation and is recognized today as one of the key factors of the project's success. The primary results were: fast and efficient start-up of facilities, due to quality programming and implementation; a plant able to operate as a single entity; automation and IT systems delivered before time and under budget; standard programming methods implemented throughout the plant; and reduced and simplified maintenance."

Jan 1, 2006

By S. Amid, D. Fisk

"Wireless technologies are permeating the mining and metals industry and enabling a myriad of benefits. With standards such as IEEE 802.11 for wireless devices and ISA100.11a for wireless field instruments protecting their investments, customers look to benefit from the cost and flexibility offered by wireless devices. Using wireless field instruments, plants are eliminating the costs associated with wired system by 50 to 70% and using these savings to install more field instruments, which, when used smartly, enables them to optimize their processes efficiency and equipment reliability. Wireless also empowers a mobile workforce by allowing them to have access to key process and maintenance data directly from the field. This paper describes how wireless can help operations and maintenance personnel to be more effective. Three case studies, illustrating how the mining and metals industry is taking advantage of the technology today, are presented:1.,Optimisation of the water recovery process using wireless2.,Field operations improvement with wireless handhelds3.,Improving fleet maintenance through wireless mobile equipment management"

Jan 1, 2011

By N. A. Beier, N. Slingerland

"Oil sands tailings impoundments rank among the largest (spatially) in the world, covering a total of approximately 220 km2 of northern Alberta, Canada. A preliminary geomorphic design for an oil sands tailings storage facility (TSF) landform was completed with the goal of eventual closure and delicensing in mind. This paper outlines methods identified during the design process that streamline closure when implemented early in the mine planning and TSF design stages. With most oil sands TSFs currently in active operation (and some still in the planning stages), geotechnical engineers and mine planners have the opportunity to make operational and design decisions, such as those outlined herein, that are likely to improve the geotechnical and environmental performance of the landform post closure. ¦ KEYWORDS Alberta, Athabasca oil sands (AOS), Landform design, Reclamation, Sand dam, Tailings storage facility (TSF) RÉSUMÉ Les bassins d’accumulation des résidus issus des sables bitumineux font partie des plus grands (en termes d’espace) au monde, et couvrent au total environ 220 km2 dans le nord de l’Alberta, au Canada. Une conception géomorphologique préliminaire a été réalisée pour le modelé d’une installa¬tion de stockage des résidus (ISR) issus des sables bitumineux en gardant à l’esprit la fermeture et le retrait de permis à terme. Cet article présente les méthodes identifiées pendant le processus de conception qui simplifient la fermeture lorsqu’elles sont mises en oeuvre dès les premières étapes de planification de la mine et de conception de l’ISR. La plupart des ISR issus des sables bitumineux se trouvent dans des exploitations actives (dont certaines en sont encore aux étapes de planification), aussi les ingénieurs géo¬techniques et les planificateurs miniers ont la possibilité de prendre des décisions en termes d’exploita¬tion et de conception, telles que celles présentées ici, qui pourraient améliorer la performance géotechnique et environnementale de la phase suivant la fermeture du modelé. ¦ MOTS CLÉS Alberta, assainissement, barrage de sable, conception du modelé, installation de stockage des résidus (ISR), sables bitumineux de l’Athabasca (SBA)INTRODUCTION The Athabasca oil sands (AOS) underlie 140,200 km2 of land in northeastern Alberta, Canada. Oil sands located within 100 m of the original surface account for 4,800 km2 of the total area and are considered to be economically mineable (Figure 1; ERCB, 2009). Bitumen, the thick, tar-like substance contained in the AOS, is extracted through open-pit mining and in-situ methods. During mining, the overburden is first removed as waste and the sandy, bitumi¬nous ore (“oil sand”) is transported to processing facilities via conveyor belts and 400 t trucks. Warm and hot water, as well as process aides such as caustic soda, are mixed with the oil sand, creating a slurry from which bitumen is mobilized and extracted. The resulting slurry waste product is called “tailings” and contains mineral solids, process water, and small proportions of unrecovered bitumen (Masliyah, Zhou, Xu, Czarnecki, & Hamza, 2004; Sobkowicz & Morgenstern, 2009)."

Jan 1, 2019

By M. W. Wadsley

"Physical and chemical property models are widely used in process engineering. There exist, in the published literature, completely empirical models of ''thermodynamic properties"", that is, property models that are not consistent with the laws of thermodynamics. There also exist property models that purport to be thermodynamically consistent but are flawed in their implementation. There are also published property models that are consistent with the laws of thermodynamics but that do not reproduce property values with an acceptable accuracy. A practicing engineer might be asked to assess very different property models for which there are a variety of claims. This paper discusses features of thermodynamic and empirical property models that may assist in their practical evaluation and implementation."

Jan 1, 2005

By R. O. Burt

"IntroductionThe introduction to this section on gravity concentration indicated the wide range of equipment types that exist for the concentration of minerals, in what is the broadest size range of any concentration process.The equipment described in this chapter includes jigs, tables and sHme plant equipment. In contrast to the equipment described in the two succeeding chapters, this range of equipment, in nearly every instance, superimposes a mechanical movement on the fluid motion to effect separation of the valuable mineral from the waste mineral. The motion may be vertical Gigs), reversing (tables), or rotary (slime plants): however, in common they ""dilate"" the bed of particles to allow preferential settlement of the heavier particles.Description of Process UnitsJiggingJigging is the sorting of different minerals by stratification, based on the movement of a bed of particles relative to a fluid in a vertical plane.The basic construction of a jig is shown in Figure 1. Essentially it consists of an open tank filled with a fluid, normally water, with a horizontal jig screen at the top and with a spigot in the ""hutch"", or bottom compartment, for removal of heavies. The jig beri consists of a layer of coarse heavy particles (ragging) on the jig screen. This ragging is of a specific gravity between that of the minerals it is intended to separate.In operation the bed is made fluid by a pulsating current of fluid to provide stratification. On the upward or pulsion stroke the bed of ragging and slurry is normally Hfted as a mass, then as velocity of the upcurrent decreases it dilates, loosening the whole mass. On the downward or suction stroke it closes slowly again. The ideal is to control this dilation of the bed of material so that the heavier and smaller particles penetrate the interstices of the bed, while the larger heavies fall under a condition akin to ""hindered"" settling."

Jan 1, 1989

By Vlad Ruzicka

"Uranium deposits in the Rabbit Lake-Collins Bay area are associated with the sub-Athabasca unconformity which separates crystalline Archean or Aphebian basement rocks from Helikian clastic sedimentary rocks of the Athabasca Group. The basement rocks are a part of Wollaston lithostructural domain.Most of the high grade deposits, such as Collins Bay ‘A’ and 'B' Zones and Eagle Point are associated with altered rocks of the basal unit of the Wollaston Group. Some deposits, such as Raven and Horseshoe are confined to the uppermost unit of this Group. The Rabbit Lake deposit occurs in the middle, meta-arkose unit of the sequence. Locations of some deposits (Rabbit Lake, Collins Bay ‘A’ and 'B' Zones) are also controlled by thrust faults, such as Rabbit Lake Fault and Collins Bay Fault.The deposits contain either monometallic (uranium) mineralization (Rabbit Lake, Raven, Horseshoe) or polymetallic (mainly uranium-nickel) assemblages (Collins Bay “A’ and 'B' Zones).IntroductionThe Athabasca Basin region, a part of the Churchill Geological Province of the Canadian Shield, is composed of Archean and Aphebian crystalline basement and younger, Helikian, unmetamorphosed supracrustal rocks. The Rabbit Lake-Collins Bay area is situated at the eastern margin of the Athabasca Basin region, which hosts a substantial proportion of Canadian uranium resources.The crystalline basement complex was subdivided by Lewry and Sibbald (1979) into lithostructural domains and these domains were grouped into major crustal units designated, from northwest to southeast, as Western Craton, Cree Lake Mobile Zone, consisting of Wollaston, Mudjatic and Virgin River domains, and Rottenstone Complex (Fig. 1)."

Jan 1, 1986

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90's to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

By R. E. MacAfee

THERE have been great changes in the design, capacity, and pressure of steam generating units over the past fifty years. If we go back as far as 1890, the plants then existing were largely horizontal return tubular boilers, hand-fired, with the boilers supported on the brick sitting which was com-posed of red brick with, probably, a refractory lining one brick thick in the combustion chamber. About this time, the water tube boiler began to supplant the H.R.T. boiler and, where new plants were being constructed of any size, water tube boilers were largely installed. In those days, say from 1890 to 1905, a 250 h. p. water tube boiler was considered a large unit. These boilers were largely the straight tube type and were set with the first row of boiler tubes three to six feet above the grates. The brick setting was a combination of red brick and fire-brick. The fire-brick lining in the furnace proper was usually 9 in. thick and in the first pass 4 1/2 in., while the rest of the setting was entirely red brick. These units were largely hand-fired and were expected to produce about 100 per cent rating as a maximum. It may be well at this point to define rating, which is the evaporation of one boiler horse power per hour by each ten square feet of heating surface in the boiler. A boiler horse power is the evaporation of 34.5 pounds of steam from and at 212°F. Consequently, a boiler containing 2,000 square feet of heating surface is rated at 200 h. p. and the evaporation at 100 per cent rating is 200 X 34.5, which equals 6,900 pounds of steam per hour from and at 212°F.

Jan 1, 1939

By J. Gogal

Cameco's Cigar Lake Operation (CLO) started commercial uranium ore production in 2015. Initial mining was focused in areas of the ore body with relatively low concentrations of elements of concern (EOCs). As mining progressed into areas of the ore body that were richer in EOCs, some statistically significant behavior of certain analytes was noted in the water treatment circuits. It was ultimately found that the CLO ore body natively hosts numerous alkyl arsine compounds in addition to inorganic arsenide minerals. The alkyl arsines were found to be recalcitrant to typical adsorption on ferrihydrite, with the degree of recalcitrance associated with the degree of alkylation. A number of changes to the process circuits and water balance were performed and planned in order to inhibit the transport of alkyl arsines from the ore stream into the process water stream, and to optimize the overall site water usage. In some instances, the interactions of equipment in conjoined circuits of the process had controlling effects on the behavior of the overall circuit. Work continues to iterate upon the capital design features in order to further tighten the water balance, and to optimize water usage and operating costs.

Jan 1, 2020

By A. R. Laplante

Gold recovery early in the flowsheet, typically from the primary grinding circuit, has seen significant advances in the past three years. Some of the advances achieved under the auspices of the AMIRA P420B Gold Processing Technology project are reviewed. The areas covered are gravity-recoverable gold (GRG) characterization, GRG behaviour in classification, gravity recovery simulation and the link between gravity recovery and cyanidation.

Jan 1, 2005

By E. Best

In 2003, Phelps Dodge Mining Company decided to pursue the design and construction of a Central Analytical Laboratory to provide chemical analyses for their Arizona and New Mexico operations. This centralized approach was selected in place of refurbishing six (6) older laboratories that operated at the various Phelps Dodge sites, and which would not have permitted full automation and use of robotics. The new lab was designed by the Process Technology Center (PTC) Material Characterization Group in cooperation with IMP Group. The Central Analytical Service Center (CASC) encompasses fully automated sample preparation of blast holes and geological samples weighing up to 15 kg/sample. The CASC also includes the first "wet chemistry module" worldwide to be operated by robotics systems to perform Total Cu, Acid Soluble Cu, and Quick Leach Tests (QLT), and a fully automated lab for electrowon copper cathode. The new lab also offers flexibility for handling specialty samples and analyses by either semi-automated or manual mode. Data handling and transfer is accomplished using the commercially available StarLIMS system. Commissioning was accomplished within five (5) months of startup during which the CASC also handled 86% of a full production load. The 24/7 lab operation has already exceeded its design capacity, has achieved considerable savings in operating cost, reduced sample preparation errors, and significantly increased analytical quality.

Jan 1, 2007

"10.1. IntroductionAs discussed by Westland (1981), the six platinum-group elements (PGE) belong to the Group VIII transition metals, to which iron, nickel and cobalt also belong. The chemical similarity between these nine metals accounts for the fact that they tend to be concentrated together as a result of geological processes. These processes started to effect the distribution of these metals at the very beginning of the earth's history.The first line in Table 1 gives the concentration of nickel and certain other Group VIII transition metals in carbonaceous chondrites, those meteorites with a composition that is believed to reflect best the composition of our planetary system apart from hydrogen and helium. The second line is the estimated concentration of the same elements in the earth as a whole. It is seen that these two estimates are quite similar, the earth being perhaps 2 to 3 times richer in these particular metals than the planetary system as a whole. The reason for this is not fully understood, but it may be due to the earth being formed by the accumulation and capture of a greater proportion of iron (and therefore siderophile-rich) than stoney (and therefore siderophile-poor) planetesimals than the planetary system itself.The third line in Table 1 is the average composition of the crust of the earth. With the exception of iron, all of the Group VIII transition elements are rare in the crust, present at concentrations of It tOO to Itt ,000 of that of the bulk earth. This is because the outstanding chemical characteristic of this group of elements is their siderophile nature; that is, their tendency to alloy with metallic iron. Because of this, once the earth became molten very early in its life history, these elements dissolved in the molten iron present at this stage and were removed from the outer accessible parts as this dense liquid sank to the centre of the earth to form the core. Although iron was the main instrument of concentration of the Group VIII metals, its much greater over-all abundance and its ability to combine with oxygen more easily than the others in the group means that significant amounts still remain in the oxidized portions of the earth.The fact that most of the Group VIII metals are available to use in workable concentrations at all is that they are 5 to 30 times more concentrated in the earth's mantle than the crust, as shown in line 4 of Table I. There has been a constant, if slow, interchange of matter between the mantle and the overlying crust throughout most of the earth's history and, under certain circumstances, this interchange has given rise to economic concentrations of metals."

Jan 1, 1979

By G. M. Carrie

Introduction The subject of basic refractories is daily becoming of increased importance in metallurgical processes, and there is a constantly growing necessity for the development of better materials. This fact, together with the realization that Canada possesses one of the best sources of such refractories in the British Empire, if not in the world, made it appear? advisable that the subject be presented to the Empire Mining and Metallurgical Congress at the 1927 meeting. Having been in close touch with developments in the Canadian product during the past five years, G. M. Carrie was requested to prepare such a paper. The Canadian producers of magnesia refractories have succeeded in developing the product to a place where it has almost entirely displaced imported materials from the Canadian market. These developments were made possible by a close study of the methods of preparation of the material, and by an exceedingly careful control of the manufacturing process so as to obtain a thorough blending of the different constituents with the resultant uniformity of composition. This point is very important to the metallurgist, as un-uniform materials are a potent cause of difficulties in most manufacturing processes and the constant trend is towards their elimination. The temperature at which the Canadian material is burned ensures high specific gravity and thorough shrinkage. The grain size of the product is so controlled that the voids are only just sufficient to allow of proper bonding, thus making possible a dense, hard bottom affording high resistance to erosion and shock. Careful proportioning of the constituent elements absolutely prevents disintegration.

Jan 1, 1927

By N. Bahrani

Knowledge of the state of stress in the Earth?s crust is very important to the safe and efficient development of underground excavations in mining and civil engineering projects. A number of methods have been developed over the past 40 years to assess the stress field in the rock mass. These range from local estimates derived from compilation of regional stress databases to back-analysis of field observations to dedicated in situ measurements. The Geomechanics Research Centre (GRC) at MIRARCO has a long history of undertaking in situ stress characterization and measurement. In this paper, the stress measurement techniques used by the GRC, including overcoring and undercoring in addition to borehole breakout back-analysis, are briefly reviewed. The limitations and application of each technique for different ground conditions and the challenges involved during the field work and in interpretation of the results are discussed. A successful stress measurement campaign is not limited to acquiring valid local measurement, but must include a careful interpretation and integration of the measurement with other geological and geotechnical context information. Based on our experience, it is suggested that all available stress indicators and data are combined and integrated with the local geological and geomechanical conditions to derive a consistent stress characterization for a given site.

Aug 1, 2013

By H. A. Khorami, T. Wong, B. Velapatino, E. Asselin, T. Donnelly, E. Bryce, R. Dixon

A copper–nickel concentration gradient alloy was designed and fabricated through a powder metallurgy (PM) process. Copper and nickel powders were mixed with different weight ratios from 0 to 100% copper in 10% increments. Each powder mixture was poured inside a cylindrical die and compacted between two punches using a hydraulic press machine at pressures up to 70 MPa, resulting in approximately 1 mm thick layers (discs) of pressed Cu–Ni powder. These 11 Cu–Ni compacted powder layers, i.e. 0–100% Cu with 10% increments, were then compressed together with pressures up to 420 MPa to form a green part. The green part was sintered in a vacuum furnace at 1000°C for 10 hours to form a solid mass (PM part) of Cu–Ni concentration gradient alloy. In the sintering process, Cu and Ni particles fused together and formed a single piece due to diffusion of the atoms across the boundaries of the particles. The diffusion of atoms also converted the stepwise concentration change into a uniform concentration gradient. INTRODUCTION Copper has numerous applications in different industrial sectors due to its superior physical, electrical, mechanical and chemical properties such as its excellent thermal and electrical conductivity, resistance to fatigue, high ductility, and resistance to corrosion. Moreover, copper and its alloys have natural antimicrobial properties. This has opened up new applications for copper–based self–disinfecting surfaces in healthcare in an effort to mitigate healthcare–associated infections (HAIs). HAIs affect millions of patients each year, leading to significant morbidity and mortality as well as financial losses to healthcare systems (World Health Organization, 2016). HAIs spread through three main routes: (a) iatrogenic in which HAIs are a direct consequence of medical encounters and/or treatment; (b) person to person where organisms are transferred between healthcare workers, patients, and visitors; and (c) environmental where transmission occurs via contaminated surfaces and equipment (e.g. doorknobs, railings, toilets/commodes, medical carts). The use of antimicrobial copper–based materials on high touch surfaces could diminish pathogen transmission via this latter rout. This has subsequently led to the development of a variety of copper–based materials for use in healthcare settings and promoted the investigation of the antimicrobial efficacy of copper–based materials.

Jan 1, 2019

By H. D. B. Wilson

THIS PAPER has resulted from a preliminary draft of a background paper prepared anonymously for the Science Council's Special Study of the Solid-Earth Sciences in Canada. The draft was circulated to eighty-four Canadian geologists; forty-eight of these responded with criticisms of the draft. All critical re-marks were considered carefully and most have been incorporated in the final paper in an attempt to balance the author's bias, although this bias undoubtedly still appears. Indications of support for a particular statement or section were also helpful, because many of these contradicted criticisms and enabled the author to judge the consensus. Thus, all criticism could not be incorporated because the referees did not agree. It is interesting that some remarks were con-sidered overstatements by some and too bland by others. The most perplexing critical comment was one which suggested a new author was needed, and went on to name the existing author as the most likely candidate.

Jan 1, 1970

By P. G. Smith, A. Axiuk

The objective of this paper is to present, from a practical perspective, a review of the most relevant maintenance procedures that are accepted or prescribed to be the most effective in optimising service life potential and to ensure continued safe use of steel wire ropes for shaft mining applications. The paper will address the most common operational issues encountered in the care and operation of shaft ropes for both conventional drum hoists and multi-rope friction winders. For each distinct maintenance procedure presented, a limited amount of theory is discussed to identify the underlying mechanisms at play that must be addressed and to emphasize the logical basis for the recommended course of action. It is recognised that each installation is unique and that the recommended maintenance procedures may not always be practical or cost effective from an operations standpoint under select circumstances, however the intent remains to promote industry best practices for the knowledge and benefit of the mine hoisting community, from experienced maintenance personnel to new entrants to the industry alike.

Jan 1, 2023

By E. Gaucher, D. C. Gagnon

"The paper refers to methods and concepts used in the computer treatment of banks of geophysical, geochemical and geological data, relating to the exploration of massive sulphides. In particular, a data bank of 400 drill holes on independent conductors can be used to calculate probability levels of intersecting a certain quantity of sulphides according to the characteristics of the conductor. Inversely one can, using the data bank and some cost assumptions, simulate and optimize the cost of intersecting a certain quantity of sulphides by selecting drill targets among conductors according to conductivity, magnetism or gravity. Problems of noise, inherent in any simulation, are illustrated in this paper by the results of a study of the nomenclature of volcanic rocks of 27 drill holes by forty geologists. Compilations of data banks are long and timeconsuming, and it would help to standardize to allow exchange of data. We believe that such efforts may result in the discovery of more mineral deposits and at a lower cost. The present study is supported jointly by SOQUEM The New Jersey Zinc Co. and Cominco Ltd."

Jan 1, 1973

By A. J. Baer

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE EXPOSED PART OF THE GRENVILLE PROVINCE is the southeastern part of the Canadian Shield, characterized by crystalline rocks with K-Ar ages of about 1,000 million years. Its Canadian portion is bounded on the southwest by Georgian Bay •and by Paleozoic sediments south of a line passing through Orillia and Kingston, on the southeast by the St. Lawrence River valley and the north shore of the Gulf of the St. Lawrence, on the east by the coast of Labrador and on the northwest by the Grenville front, a linear tec-tonic feature that is a metamorphic transition zone and/or a fault. Rocks located to the southeast of the front have younger K-Ar radiom€tric ages than rocks located to the northwest of it.The region is formed of complexly deformed and highly metamorphosed crystalline rocks and in part differs from other areas of the Canadian Shield by the presence of large amounts of crystalline limestone and bodies of anorthosite."

Jan 1, 1970