Search Documents

By R. Barbaroux, B. Dubreuil, D. Lemieux, K. Nasrallah, G. Garcia Curiel

"As conventional, base or precious metal ores are being depleted worldwide, the mining industry is being faced with an increasing exploitation of arsenical sulfidic ores. Enargite is a common example. The downstream processing of these ores poses several problems ranging from high smelter penalties to finding economical and environmentally acceptable means of disposing of the arsenic. Several hydrometallurgical processes have been proposed for extracting arsenic from enargite concentrates, notably using alkaline sulphide leaching (ASL). However, few alternatives exist for removing the arsenic from solution and stabilizing it in an approach that is both economical and environmentally acceptable.Dundee Sustainable Technologies (“DST”) has developed a technology for the sequestration of arsenic by vitrification. Originally optimized to cost-effectively stabilize arsenic trioxide (As2O3), DST has shown that vitrification could be successfully extended to the stabilization of other arsenical products, such as calcium arsenate (Ca3(AsO4)2) and sodium arsenate (Na3AsO4). In this paper, the vitrification of arsenic in the context of an enargite leaching was newly explored and demonstrated successfully.Two processing routes are being proposed by DST for the removal of arsenic from enargite concentrates and their stabilization by vitrification. In one route, arsenic is extracted by ASL and is then precipitated under atmospheric conditions and with minimal use of reagents and time. The resulting precipitate is an unstable hydrated ferric arsenate (FeAsO4•2H2O) that is then vitrified in a non-dilutive method, significantly increasing the stability of arsenic and meeting the TCLP guideline. Unlike is required for scorodite, stabilization was successfully achieved without concern for the crystallinity of the precipitate."

Jan 1, 2017

By Robin Sheremeta

What is the goal of every organization when it comes to safety? Everyone Going Home Safe and Happy Every Day Good old days: Era of Death (accidents will happen) Era of Engineering: (Eg. hand rails, limitswitches, machine guards, etc.) Era of Legislation: procedures, laws and regulations (Eg. SWP?s, Mines Act) Era of Behaviour-Based Safety: (eg. STOP program)

May 1, 2010

By W. Fergusson

This paper takes a look at the use of rubber to provide corrosion resistance and wear resistance in the mining industry. The longer life and reduced down time involved with the use of rubber are stressed, and examples are given of applications in grinding mills, skips, discharge chutes and screens.

Jan 1, 1979

By D. Linzey

"History of Whitehorse Copper BeltThe first discovery of copper on the Whitehorse Copper Belt is reported to have been made by miners on their way to the Klondike in 1897. By 1899 the district had been well prospected and many of the presently known deposits had been staked.The first shipment of ore was from the Copper King property in 1900. This consisted of 9 tons of hand picked ore grading 46.4% copper. It was not until the period between 1912 and 1917, the production years of the Pueblo Mine, that significant ore shipments were made. Total production was 140,000 tons at 3.5% copper. An underground disaster killed six men and closed the mine in March 1917.Although the general area was dormant until after World War II, by 1947 geological mapping, magnetic surveys and diamond drilling had been done on the important showings. In 1954 Mr. Aubrey Simmonds directed the formation of Imperial Mines and Metals, which acquired by option and staking a large part of the Whitehorse Copper Belt. In 1957 Mr. Arnold Pitt reorganized the company as New Imperial Mines. With financing from Sumitomo and Toronto-Dominion Bank, a mill was built and production was started from the Little chief orebody by open pit in 1967."

Jan 1, 1977

By V. Prostakova, M. Shevchenko

The copper smelting gas / slag / matte / metal / solids system with the Cu-Fe-Ca-Si-O-S major elements has been a long-term focus of the present overall research program using integrated experimental and modelling approach for the phase equilibria characterisation and development of a thermodynamic database. A systematic investigation of phase equilibria of slag systems in equilibrium with Cu metal is providing information for systems where copper coexists in slag with lead, zinc, and aluminium oxides as major components. Experimental studies involve high-temperature equilibration of synthetic samples; rapid quenching; and measurement of the compositions of equilibrium phases using electron probe X-ray microanalysis (EPMA). Particularly important feature of the present study a wide range of temperatures (660-1670°C) being characterised that reveals major inconsistencies in the existing thermodynamic description of the multicomponent system, and allows to establish the thermodynamic properties from phase equilibria in a reliable way. FactSage-based thermodynamic modelling is integrated with experimental research. Initial thermodynamic assessments are used to identify priorities for experiments, planned to provide specific data for thermodynamic optimisation. Significant improvement in the accuracy of the phase equilibria description is achieved, in particular in the PbO-Cu2O-SiO2, ZnO-Cu2O-SiO2, and Cu2O-CaO- Al2O3 systems in equilibrium with metallic Cu. INTRODUCTION Slags high in lead and copper are generated in primary metal production in the smelting of lead sulfide concentrates and in pyrometallurgical metal recycling systems. The compositions of these slags are varied due to increased fraction of recycled materials in the feed as well as introduction of previously unused chemical elements to modern technology. Therefore, their processing becomes chemically more complex; in that way they contain a large number of different metals. These slags form complex non-ideal solutions (with possible formation of several immiscible slags) that can coexist with stoichiometric solids, solid solutions, mattes and molten metal depending on the bulk composition and process conditions. Predicting the outcomes of smelting and refining processes is becoming increasingly difficult. To assist in the optimisation of these metallurgical processing operations, a comprehensive research program is underway to develop accurate thermodynamic databases for these non-ferrous process systems.

Jan 1, 2019

By Renato Macciotta

The argillaceous formation known as the Opalinus Clay is host to the Mont Terri Underground Research Laboratory. The URL was developed to investigate the hydrogeological, geochemical and geotechnical properties of the formation. Underground excavations at the site are characterized by non-elastic and time-dependent deformations. Excavations trending perpendicular to the strike of the bedding presented relatively minor deformations, however, tunnels parallel to the strike of the bedding showed much larger non-elastic deformations. This paper presents an analysis of the measured response of a tunnel trending parallel to the strike of the bedding in Opalinus Clay. The measured convergence is compared to tunnel experience in weak rocks to assess the tunnel stability.

Jun 1, 2012

By R. G. L. McCready, R. O. van Everdingen, M. Kalin, R. van Everdingen

"This paper is based on data generated between October, 1986 and October, 1989, during the implementation of an Ecological Engineering close-out for a zinc mine in Northern Ontario, where 690000 tonnes of tailings contain 41.1% pyrite and 4.1% pyrrhotite. The objective was to determine rates of sulphide oxidation and iron precipitation in the tailings. Those rates are relevant for the assessment of the long-term effectiveness of biological systems employed in the removal of heavy metals from contaminated drainage issuing from tailings.Data were collected on the topography and stratigraphy of the tailings basin, subsurface temperatures and groundwater levels, and chemical analyses were made of water samples collected from a number of piezometers. The thickness of unsaturated tailings varied widely between individual piezometer locations; annual maxima ranged from 0.67 m to 3.55 m, and annual minima from 0 to 2.68 m. Sulphate concentrations ranged from 36 mg/L to 20180 mg/L; iron concentrations from 0.36 mg/L to 9938 mg/L; and zinc concentrations from 0.33 mg/L to 1123 mg/L.The geochemistry of the piezometer samples suggests that some of the initial Fe content, resulting from metal sulphide oxidation, is subsequently precipitated in the tailings pile and, possibly, in the underlying unconsolidated sediments, probably in the form of iron-hydroxide and Na-jarosite. Other metals such as Zn may be co-precipitated with Fe. The discharge of a portion of these metals to the environment would be delayed by this process. Some of the initial sulphate may also be lost from solution, probably by precipitation of gypsum; approximate saturation degrees for gypsum ranged from -3.27 to +0.47. The precipitated minerals will somewhat decrease the porosity and permeability of the tailings.Sulphide-oxidation rates, calculated using the analytical results and the estimated amount of annual recharge at the tailings site, average 0.0057 mol/kg/yr. Calculated iron-precipitation rates average 0.000386 mol/kg/yr. It is concluded that the characteristics of seepage from mining wastes may change with time, reflecting the solubilization of precipitated secondary minerals."

Jan 1, 1992

By John Lindsay

Outline ??Recovery plant requirements and concepts ??Common recovery plant unit processes ??Recovery plant design considerations ??Peripheral issues Process Design ??Liberation ??Separation ??Recovery Processing ??Density 3.5 g/cm3 ??Luminescent under x-ray ??Hydrophobic (non wettable) surface ??Non-magnetic ??Inert to strong acids / bases

Apr 1, 2005

By H. E. Lake

VERY EARLY in the initial stages of underground development work at Eldorado's Beaverlodge operation, the decision was made to use mill tailings as a backfill product. Mining and milling commenced in June, 1953, using locally available sand as backfill, while test work and installation of a plant was carried out to prepare ?and deliver the tailings to the mining areas. The first use of tailings was made in February, 1954, a sandslime separation being carried out with hydraulic cyclones. To date (January. 1956), approximately l 40,000 tons of fill have been used in the stoping areas, providing very effective support in a 50 deg. Vein system of cut-and-fill mining. The recoverable portion of the mill tailings amounts to 40 to 45 per cent, which has resulted in a product giving a percolation rate of 6 to 10 inches per hour. Owing to the fact that Eldorado has milled from 15 to 2 5 per cent more ore than it has mined, through the purchase of custom ore, the degree of control on the sand-slime separation has not been as critical as it might normally be when the filling operation must depend only on the tailings from ore mined. A description of the conditions involved and of the plant as finally installed is given below. It might be mentioned here that, with the impending increase in milling capacity from 700 tons to 2,000 tons p.er day, the present plant will be considerably altered within the ensuing year to handle the increased tonnage and distribution.

Jan 1, 1956

By Mousa Mohammadi

Due to operational advantage of dragline in simultaneous excavation and back-filling, the equipment has gained vast importance in open-pit mining. Besides, absence of auxiliary haulage units and a myriad of other benefits are also credited in favor of excavation of muck piles by the draglines. However, the aspects of production, productivity and economics are of utmost significance in dragline operation and planning. In this light, the present paper is an endeavor to analyze availability and utilization of dragline operations. The paper presents a good amount of data for 4-draglines operating in one of the major opencast projects in India. The study reveals the trends of availability and utilization of these draglines during last 11-years. Furthermore, the study also highlights the salient reasons for loss of available hours and for idling of the draglines. Some startling information and facts have been illustrated in form of graphs and pie charts.

Aug 1, 2013

By G. W. Neumann, J. R. Schnarr

The lead-zinc-copper-silver ores mined by Brunswick Mining and Smelting Corporation Limited at their No. 12 underground mine and No. 6 open-pit operation, and treated by distinct concentration processes in separate plants, present difficult metallurgical problems because of the extremely fine dissemination of the valuable minerals with pyrite and pyrrhotite. The problem of concentration is further complicated, in the No. 12 ore, by the presence of a varying content of graphitic carbon. This paper describes the milling of No. 12 ore and the production of copper, lead and zinc concentrates by differential flotation.

Jan 1, 1971

By G. Stokreef, B. R. Davis, M. Kadiyski, Alvear Montenegro, H-P. Loock, V. Montenegro

An optical probe for burner monitoring in copper flash smelting, first developed at the University of Concepcion, is being industrially tested in a collaboration between Kingston Process Metallurgy, Aurubis AG, and Queen’s University. The sensor uses fibre-optics and optical emission spectroscopy to analyze the light emitted from combusting particles in the furnace reaction shaft. Information that can be extracted from the emission spectrum includes the temperature and brightness of the flame, as well as emission lines or bands from excited atomic and/or molecular species. Laboratory proof of concept testing of the sensor was first completed in a continuously fed drop tube reactor using O2/S stoichiometric ratios between 0.8–4.0. These O2/S stoichiometries capture the industrial operating condition, which is typically less than 1. The results from lab testing justified a plant trial of the optical probe, which was done in the Aurubis Hamburg flash furnace in September 2018. From this trial, approximately 31 hours of spectral data were collected and synchronized with furnace operating data. The results from both drop tower test work and the plant trial are discussed with implications for process monitoring in the commercial furnace. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process. It is used to treat copper sulphide concentrates and small amounts of secondary materials, such as dust generated by the process. O2 enriched air and the concentrate blend are fed into the furnace reaction shaft through the concentrate burner. As the particles fall through the reaction shaft, they heat up and ignite, causing rapid, exothermic reactions that oxidize the iron sulphide, some copper sulphide and impurities in the feed. Reacted particles fall into the settler of the furnace, melt and separate into a matte and slag, while the SO2 enriched off-gas is carried out of the furnace for heat recovery and H2SO4 production. Operation of the furnace is achieved by adjusting a limited number of control variables. The main variables are the blast feed rate, blast oxygen enrichment, SiO2 flux feed rate and CH4 combustion rate (CH4 is used when the chemical energy of the concentrate is low) all measured relative to a set feed throughput. (Davenport & Partelpoeg, 1987; Davenport, King, Schlesinger & Biswas, 2002) The batch tapping nature of flash furnaces makes operation difficult because these control variables impact each other, and product quality can only be measured when matte and slag are tapped from the furnace. This means that operation of a furnace is based on feedback control from matte and slag assays. Because of the time-delay associated with understanding product quality, there is interest in using technology to monitor the combustion reactions that happen in the furnace reaction shaft.

Jan 1, 2019

By A. Dolatmoradi

Nanocrystalline structure formations produced by severe plastic deformation in Fe-0.15C with initial ferritic-pearlitic and IF steel with ferritic microstructures have been studied through microstructural observation and microhardness measurements. It was found that the nanocrystalline region first forms near the surface of samples due to localized severe deformation. It was also observed that the nanocrystallization rate of Fe-0.15C and IF steels and the deformed layer thickness in these two materials are different with similar milling conditions. The crystallite size and structural evolution of the samples during milling was studied by employing XRD and SEM.

Jan 1, 2010

By M. Leijd, K. S. Forrester, M. Saxon, M. Oczlon

This paper provides an introduction to wet high intensity magnetic separation (WHIMS) and its successful application to the beneficiation of rare earth element (REE) enriched eudialyte. The analysis includes an in-depth reporting of the deportment of key elements as well as a statistical interpretation of the relative importance of operational parameters including magnetic field intensity, flow velocity, and matrix loading density. Conclusions are drawn on the relative success of the technology, potential areas for process improvement, and the research direction that continues to be investigated. Three original equipment manufacturer (OEM) technologies were subjected to a series of screening and characterization tests to identify the optimal operating parameter set to magnetically beneficiate eudialyte from Norra Kärr, Sweden. Upon the completion of the characterization test it was apparent that the Metso HGMS technology was superior with respect to REE recovery and gangue rejection for the Norra Kärr composite. The Metso HGMS was then subjected to a series of verification tests to confirm the repeatability and reproducibility of the system.

Jan 1, 2014

By G. Molloy

The purpose of this paper is to demonstrate the value of applying continuous improvement, in particular 5S and standard work, in an underground environment. 5S and standard work are two aspects of Lean manufacturing that have been applied in many industries. At Vale Canada Limited, the focus is to first stabilize the process, commonly through the use of 5S, standard work and other continuous improvement techniques. In parallel with building an engaged workforce, these approaches aim to incrementally stabilize and improve a process. 5S is an employee-driven, systematic methodology to reduce waste in all its forms through attaining, maintaining, and improving workplace organization. Identified as a foundational part of any improvement process, 5S aims to remove wastes that impact on the overall efficiency of the area. Standard work is used to formulate a common approach to how tasks are carried out to ensure consistency. Standardization involves identifying, establishing, and following the best method. The aim is to eliminate the variation that can occur when there is not a pre-defined established standard. Demonstrating the value of 5S and standard work in an underground environment will be achieved by first understanding the overall concept of Operational Excellence and continuous improvement as practiced within our operations. The paper will then cover a real application of 5S and standard work within the underground environment at Thompson, Manitoba.

Aug 1, 2013

By P. J. Mackey, Elsie Kossatz

The small town of Bruce Mines lies a few miles east of Sault Ste. Marie, Ontario on the north shore of Lake Huron. This was the site of the first copper mine. This copper smelter used a reverberatory furnace, based on the Welsh process, and operated in the period of 1849 to 1850, when the plant was destroyed by fire. During the period of 1850 to about 1869, crushed and sorted ore was shipped to England and later to the United States. In 1869, a roastleach plant, based on the Henderson Process, was constructed at Bruce Mines and was operated until about 1872. This short article describes the early development of this historic operation. Although the rich copper ore found in the vicinity of Bruce Mines was known to the Indians, its discovery in or about 184 7 was credited to Mr. Keating, who named the area Bruce in honour of Lord Elgin (James Bruce), Canada's Governor General. In 1848, the property was acquired by the Montreal Mining Company for 40 000 pounds sterling and the company immediately sent a small party to investigate the deposit. The party sank a shaft on a lode within a hundred yards of the lake and also reported two adjacent lodes farther inland, which were left undeveloped until the turn of the century. Initially, the foundation of the headframe and hoist was built above the frost line and when the machinery was set in motion it collapsed. Eventually, the shaft was to reach a depth of 300 feet. By 1849, the property was well established and the small settlement consisted of 77 miners, 65 labourers, 4 boys, 11 tradesmen, including blacksmiths and carpenters, 2 mining captains, 1 engineer, 2 clerks and 1 superintendent. The community, including the workers' families, numbered about 250.

Jan 1, 1999

By Marty Hudyma

There are five independent seismic source parameters: seismic energy, seismic moment, source size, location, and time. These parameters are investigated primarily for evaluating seismic hazard and understanding seismic source mechanism(s). Broadly, seismic hazard is the likelihood of occurrence of an event of a given magnitude. Seismic source mechanism is the mode of rockmass failure that causes the seismic event. Most mine seismicity analysis techniques use a combination of a few of the independent source parameters. In literature, time is perhaps the least discussed and most underutilized of these five parameters. This paper discusses three applications of time to understand both seismic hazard and seismic source mechanism in mines. The first application is time history analyses, which focuses on how other parameters of interest vary over time. Examples are presented to show how time history analyses can give information about both seismic hazard and seismic source mechanism. The second application is analysis of time-between-events. This technique can give insight into seismic source mechanism. The final application is phasor analysis using the Schuster test. This method can be used to investigate how seismic source mechanisms may change over time. For both time-between-events analysis and phasor analysis, there are important implications with regards to scale dependence and the breakdown of self-similarity of mining-induced seismicity.

Jun 1, 2012

By Ltd. (CYMCO) Technology Center Yunnan Metallurgical Group Co., S. Jian, T. Song, J. D. Miller

"As sulfide zinc ore deposits become exhausted, nonsulfide zinc ore deposits become the other resource for zinc production. However, flotation for zinc recovery from nonsulfide deposits is much more difficult than the flotation of sphalerite from sulfide deposits and may become an option for zinc production only if a suitable processing technology is developed. In this regard, research efforts are being devoted to the flotation of nonsulfide zinc oxide minerals. Some common methods which have been used for the flotation of zinc oxide minerals include sulfidization-flotation, activation, and direct flotation with anionic and cationic collectors. The traditional flotation techniques have low efficiency and difficulty in separation and recovery of the zinc minerals from gangue minerals, for example, smithsonite (ZnCO3) from other carbonate gangue minerals and hemimorphite (Zn4Si2O7 (OH)2·H2O) from silicate gangue minerals. In this study potassium lauryl phosphate was evaluated as a collector for the flotation of nonsulfide zinc minerals. Results from contact angle and microflotation experiments at pH 6–9 show that hemimorphite (Zn4Si2O7 (OH)2·H2O) can be floated from quartz and that smithsonite (ZnCO3) can be floated from calcite. However, when dodecylamine, which is a common collector reported in literature for the flotation of nonsulfide zinc minerals, was used as collector, no significant difference between nonsulfide zinc minerals and gangue minerals was observed at any pH value. Initial evaluation suggests that potassium lauryl phosphate is effective at low concentration and may be a promising collector for zinc oxide mineral flotation.INTRODUCTIONBefore the twentieth century, zinc was mainly produced from nonsulfide ores (Large, 2001; Gilg, Boni, & Cook, 2008). With the development of differential flotation processes in the late 19th century major production switched from nonsulfide zinc sources to sulfide zinc ores (Hitzman, Reynolds, Sangster, Allen, & Carman, 2003; Gilg et al., 2008). However, as it is becoming more difficult to find new sulfide ores, recovery from nonsulfide deposits is being considered. Nonsulfide flotation for zinc recovery is much more difficult than the flotation recovery of sphalerite from sulfide deposits and may become an option for zinc production if a suitable technology is developed. Zinc and lead oxide ores are difficult to beneficiate ores due to their similar floatability with gangue, high solubility in water, and the influence of slimes (Fa, Miller, Tao, & Li, 2005). In order to improve the performance of oxidized minerals, lots of effort is being devoted to this field of study (Ejtemaei & Mahdi, 2014)."

Jan 1, 2016

By H. H. Wober, P. J. Morgan

"The proposed classification of ore reserves based on geostatistical and economic parameters is designed to be used as a communication tool to identify for investors, bankers, and financial analysts the degree of risk associated with a specific class of ore reserves. The class designation identifies the degree of accuracy of the estimates for tonnage and grade of annual production volumes of ore. It thus enables decision makers to quantify the risks and uncertainties inherent to the ore reserve in achieving over-all economic goals and annual financial objectives.IntroductionDuring the evaluation, in 1980, of the Creede silver deposit in Colorado, U.S.A., as a potential bulk mining project, the authors were faced with the problem of conveying to senior management the risks and uncertainties that are implied by using common or conventional classification systems to categorize ""ore reserves"". The estimated numbers for tonnages and grade of the projected ore reserves represented the only entry for future revenue from the project. It was, therefore, necessary to convey to management the level of risk associated with those numbers when implementing further stages of development, and to convey what impact significant differences would have on the profitability of the project. The desire to quantify these risks led to a revised definition of ""ore"" and to a re-examination of the classification system of ""ore reserves"". Traditional methods for estimating tonnage and grade of reserves do not include a quantification of the errors of these estimates. The advent of geostatistical methods made this quantification possible. The proper application of geostatistical methods, with adequate geological input and a reliable set of sample data, is essential to its validity.Others have proposed a classification of ore reserves based on geostatistical parameters. Diehl and David (1982) recognized ""that concepts of proven, probable and possible have to be linked to the production rate or time horizon"". Royle (1977) had also addressed this problem. Forsyth (1987) pointed out that bankers are concerned with ""the probability that the variability will fall within a certain degree of accuracy"" especially for grade estimates, and would like to see grades expressed together with the error of the estimate at the 950Jo confidence level."

Jan 1, 1993

By J. F. Liu, L. Chen, C. P. Wang

"Calcite-cemented joints abound in the rock masses of Beishan area, which is the most potential area for the high-level radioactive waste (HLW) disposal of China. The mechanical properties of Beishan granite containing a calcite-cemented joint with a dip angle of 82° was investigated under uniaxial compression and the acoustic emission (AE) characteristics were also studied in this paper. Compared to intact granite, the calcite-cemented joint caused a decrease more than 50% in uniaxial compressive strength and a decrease more than 90% in shear strength. The Young’s modulus was also decreased, while the circumferential deformation of jointed granite was sharply increased. The AE monitoring system successfully recorded the process of micro-crack development and the results indicated that the risk of rock-burst could be reduced due to the appearance of calcite-cemented joint.INTRODUCTIONThe properties of jointed rocks differ considerably from that of intact rock. Due to the difficulties in specimen preparation, analogue experiments with artificially prefabricated fractures are often used to study the mechanical behavior of jointed rock (Chen et al. 2012; Kulatilake et al. 2001; Singh et al. 2001). However, natural joints are not quite similar to the artificial fractures and it is necessary to investigate the mechanical behavior of jointed rocks. Xie et al. 2011 studied the mechanical properties of marbles with natural joints by uniaxial compression tests and found that the uniaxial compressive strength of jointed rock is greatly decreased. With the unaxial compression tests, Jacobsson 2005, 2007 tested the intact and jointed granites, which were taken from the potential site for high-level radioactive waste (HLW) disposal of Sweden. However, no significant difference in strength or modulus was found. The above research results are inconsistent and it indicates the complexity of the mechanical properties of natural joints."

Jan 1, 2015