Search Documents

By R. B. Throndycraft

"1. Belt-Drop Agglomeration Preferred at Heap Leach Operations. The agglomeration method now preferred at heap leach operations utilizes belt-drops along conveyors. Belt-drop agglomeration is being designed into numerous upcoming heap leach operations. It offers substantial capital cost savings over previously favored drum agglomerators. It has such significant operating and maintenance advantages that some drum agglomerators have been retired in favor of belt-drops.The majority of heap leach operations are now built with crushing included in the flowsheet. If crushing is included, belt-drop agglomeration can be added for almost no cost. The agglomeration equipment is simply a few conveyor transfers, designed to provide the tumbling and rolling action which forms the agglomerates. Controlled water sprays are needed at each of these agglomeration transfers. Cement or lime is added as a binder, to stabilize the agglomerates. This reagent is also needed to raise pH to safe operating levels.Addition of the pH control reagent before stacking the ore offers a reagent cost benefit. In the belt-drop mixing technique, the ore is intimately mixed with the lime (or cement). After stacking on the heaps, when the cyanide solution is sprayed onto the high-ph ore, very little cyanide is consumed. Without the pre-addition of lime or cement, the leach solution is sprayed onto neutral ore. The mixture of high-pH leach solution and neutral pH ore causes the solution pH to drop, releasing cyanide gas. This release is minor from a safety viewpoint, much less than dangerous, but the gas release is a costly waste of the cyanide reagent. Pilot-scale comparison tests were made at Pinson. Ore pre-treated with lime or cement showed 30% less cyanide consumption than untreated ore."

Jan 1, 1989

The Stability Graph Method is widely used in Canadian underground hard rock mines for open stope support design and is frequently used in the mine planning phase to assess the viability of stope geometries and to determine maximum permissible spans. The Method is well accepted due to its simplicity and suitability to a wide range of mining methods requiring the use of sublevels to access and extract the mining blocks. While this Method is reliable in situations where the maximum induced tangential stress creates adequate compressive stress keeping the face in a state of confinement, the Method fails to reflect the effect of low confinement caused by lower compressive stresses and instances where tensile stresses are developed. In this paper, a new Rock Stress Factor, A?, an update to the original Rock Stress Factor, A, is proposed, which will reflect the impact of low confinement or overstress regime on critical face stability. Two case studies, based on two Canadian operating gold mine shows that using the new Rock Stress Factor A? to predict the stability of stope hanging-wall and footwall gives better agreement with the CMS survey results, compared with the prediction using the original rock stress factor.

May 1, 2011

By J. P. Aiello

"INTRODUCTIONWhile this paper deals specifically with potential coal use at the Cold Lake Project of Esso Resources Canada Limited, a majority of the technical aspects of coal conversion could apply to any oil field and industrial boilers or stearn generators. In 1962, Imperial Oil Limited's production arm (the forerunner of Esso Resources), began examining methods of extracting bitumen from a 50 m thick layer of oil sand buried 450 m below the surface in the Cold Lake area. Almost two decades of research followed to develop an in situ oil sands recovery technology that made commercial production feasible.A $13 billion mega project that would have produced 22 000 m3/d (141 000 barrels/day) of synthetic crude oil (160 000 bpd of bitumen) was shelved in 1981, and ultimately replaced by a phased development strategy, involving smaller production units, to bring blended bitumen production on stream as markets and prices permit.The first two phases came into production in 1985. There are currently a total of six phases in production with four more in the construction stage. Each phase has 130to 140production wells (initially) and a central plant with water treatment, crude treatment and stearn generating facilities capable of producing 150 m3/d (9500 bpd of raw bitumen). The stearn generation section for each phase consists of three 180millionBtulhour oil fieldsteam generators.In its natural state, the bitumen is too thick to be recovered using conventional oil recovery techniques. At the Cold Lake Project, bitumen is recovered by a method called cyclic stearn stimulation. Water is pumped to the central plant where it is treated and heated to produce high pressure, high temperature steam. During the steam cycle, this steam is transported in insulated pipelines to the wells for injection into the oil sand formation. This cycle lasts from 30 to 50 days, heating the formation and causing the bitumen to flow. Following an initial flowback period, a surface based artificial lift system pumps the heated liquid bitumen, mixed with water and gas, out of the well and back to the central plant. The water and gas are separated from the bitumen, with the gas being used to provide some of the fuel for the stearn generators and the water being treated and recycled. Approximately 5% of the water cannot be recycled and is disposed of by injection into deep formations . The bitumen is blended with a diluent and shipped by pipeline to market."

Jan 1, 1989

By Stephen L. Chryssoulis

"""Preg-robbing"" of gold by carbonaceous matter during the cyanidation of certain types of carbonaceous gold ores is well documented. Recent studies established that ""preg-robbing"" of gold is not limited to carbonaceous matter. Gold sorbed on the surface of pyrite grains was detected and quantified by TOF-LIMS (Time of Flight Laser Ionization Mass Spectrometry). Crystallites of pyrite from a number of ores from different geological environments have been shown to have gold on their surface apparently sorbed from the ore forming solutions. Surface gold accounts for significant fractions of the gold head assay. Preg-robbing of gold by pyrite from pregnant cyanide solutions was also documented, and accounts for significant losses to tailings. Preventative measures are discussed.1.0 IntroductionThe detection and subsequent quantification of gold sorbed on the surface of pyrite particulates came about during routine determinations of the deportment of gold employing the comprehensive mineralogical approach (Chryssoulis and Cabri, 1990). In some pyritic gold ores it was discovered that the sum of the various forms in which gold ""conventionally"" occurs, was short of the gold assay. The mineralogical procedure used involves the independent determination of each fraction of gold, in other words there is no form of gold which is calculated ""by difference"". The systematic shortfall after having added the forms of gold listed in Table 1 led to the inquiry for the 'missing' gold and its discovery on the surface of pyrite grains, such as crystal facets and fractured surfaces.Preg-robbing of gold by pyrite from pregnant solutions was first described by Lloyd. In his studies, preg-robbing was measured by changes in the solutions/solids gold assays. This paper describes the first application of a direct measurement method for surface gold on pyrite particles from untreated and processed samples, its impact on gold deportment and processing. The advantage of the direct measurement lies in the absence of interference from other forms of gold, leading to more accurate and precise determinations of this unconventional form of gold."

Jan 1, 1997

By H. J. McQueen

The modeling of the extrusion of 6061 alloy and its composites with 10 to 20 vol% Al203 or SiC by two techniques. The uniaxial finite element method FEM (DEFORM" ) provided force-stroke curves and temperature rise over the range 450-500 °C, 2.6-5mm/s and extrusion ratios of 31 and 64. The traditional technique considers ideal work and redundant work as well as friction and uses average temperatures and strain rates. The two techniques are used to clarify each other and to extend the analysis to 400 and 350 °C. The calculated efficiencies are compared to measured values in extrusion trials and to values derived for 7075 extrusion analyses. The analyses are based on constitutive equations determined by torsion testing tests.

Jan 1, 2004

By F. Hampshire

"IntroductionThis paper is intended to cover questions raised by operating staff at various installations and is not intended to give comprehensive coverage of power plant and power system design. The paper is concerned mainly with the electrics , although a brief section gives the reasons for selection of diesels rather than other prime movers.The material is not new but brings out points which seem to be raised regularly during the design , commissioning and operation o f a new plant. Diesels versus other Prime MoversDiesel-electric plant for the mining industry falls into two major categories -emergency power and prim e power.1) Emergency power (for use only when the regular utility supply has failed) requires reliable starting and operation and reasonable first cost. Fuel economy and maintenance are of little importance as the machine(s) generate few kilowatt hours only. The diesel's competition in this field is the gas turbine, however diesels are more widely used than gas turbines in this application.2) Prime power is a different situation as the bottom line of total cost is highly affected by fuel costs.In general , mines which are within reasonable transmission distance of an existing utility find the lowest net cost result s from hooking up to the utility. If a min e is remote from an electric utility then the possible alternatives are:a) Hydro- electric power if there is a site capable of development at reasonable cost including the cost of transmission facilities. Such sites are not common, but brief and inexpensive considerationof this possibility is warranted .b) Diesel power with consideration of different grades of fuel.c) Thermal (steam) power generation from coal or oil.d) Gas turbines.In addition to the above there is the possibility of wind power (as a supplementary source) and a number of technologies which may become feasible in the future (e.g. small nuclear plants, fuel cells). For obvious reasons, small isolated generating systems required for remote mines, tend to lean to conservative technology.Among the fossil fuel plants, the diesel enjoys advantage on over-all costs as summarized in Table 1."

Jan 1, 1986

By Glenn Kosick, John Starkey, Glenn Dobby

"A practical new test has been developed for SAG hardness determination. Using two kilogram samples of minus one inch diamond drill core or crushed muck samples, the Starkey SAG Test has been shown to give accurate predictive information which directly relates to on-stream SAG mill performance. Typical results and test criteria are discussed in the paperAchievements to date include:• Identification of hardness profiles and the location of hard and soft zones in a large ore body.• Accurate prediction of the hardness of a bulk sample by using an adjacent diamond drill hole.• Derivation of a plotted curve relating pilot plant power to laboratory relative hardness.• Demonstration that for every test done to date, the Starkey SAG Test produced a product size distribution identical to that produced in a pilot plant or full scale plant SAG operation.This test can now be used for blast hardness monitoring and short term control of mine production in existing plants and for identifying the proper locations for bulk samples in new projects. In addition, new SAG mill design can now be rationalized in a low cost way to eliminate unforeseen production shortfalls.IntroductionThis paper is presented to introduce the Starkey SAG Test, a practical new laboratory tool for measuring the relative hardness of small ore samples in a semi-autogenous grinding (SAG) environment. The test was first designed for use on diamond drill core samples during the prefeasibility stage of new mining projects, to provide new information about the ore body at reasonable cost. It is a new tool and does not replace existing pilot plant test requirements.The test will also be useful for throughput prediction in existing SAG plants by assisting in short and long term mine planning, where forecasting of metal grades and milled tonnage is used to control mine profitability. Because in-plant hardness testing has previously been unavailable on small samples, this test offers exciting possibilities for SAG mill operations where hardness variation is or could be a problem.The Starkey SAG Test provides the following benefits to the mining industry"

Jan 1, 1994

By R. W. Boyle

"EDITOR'S NOTEPart 1 of this paper, published in the August issue, covered lithochemical surveys based on major, minor and trace elements in whole-rock samples from primary enveloping halos.Part 2, which follows, continues with discussions of surveys based on leakage halos, zonation of elements, stable and radioactive isotopic distributions, and geothermometric, geobarometric, thermoluminiscent, pedochemical, hydro-chemical, atmochemical and biogeochemical methods. It concludes with a selected bibliography.Surveys Utilizing Leakage HalosLeakage halos can be used as scalar or vector quantities in thesearch for deeply buried blind mineral deposits. In the first case, the occurrence of a leakage halo (e.g. a small pitchblende seam) may simply indicate the possible presence of pitchblende mineralization or orebodies; in the second case, the areal or three-dimensional distribution of leakage halos may, by their increasing frequency and I or increasing metallic or gangue element content, provide a means of vectoring in on loci of mineralization and orebodies. Examples of both cases are given in the following text.Leakage halos are of many types, as shown in Figure 2 (Part 1), and are best discussed with respect to their associated mineral deposits. Furthermore, it should be noted that leakage halos are frequently offshoots or extensions of enveloping halos. Where this occurs, careful tracing of the leakage halo(s) downward or upward respectively will often lead to the apex or nadir (bottom) of the enveloping halo(s) and ultimately to mineralization or ore."

Jan 1, 1982

By Robert Cluff

The Campo Morado precious-metal-bearing, volcanogenic massive sulphide district occurs in a Lower Cretaceous felsic volcanic sequence in a northerly trending belt in the Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. The deposits belong to a low-sulfidation, volcanogenic massive sulphide system formed in a subaqueous environment, and are of the siliciclastic type. Most are on the flanks of felsic domes or in adjacent basins and many are associated with heterolithic volcaniclastic rocks. The Reforma and possibly the El Rey massive sulphide deposits are interpreted to be overturned, and the Naranjo, El Largo, and Estrella de Oro deposits and the El Profundo occurrence to the south are upright. The G9 deposit and the La Lucha and San Rafael occurrences are in an over-thrust plate further to the southwest. In several of the deposits, zinc, lead, silver, and gold are concentrated near the stratigraphic top, and copper is concentrated near the stratigraphic base; copper also is concentrated in replacement bodies near the top of some domes. Major minerals are pyrite, quartz, ankerite, sphalerite, chalcopyrite, and galena. Gold and silver occur in argentian gold, and silver also occurs in tennantite/freibergite and galena. Underlying stockwork zones contain disseminated and vein quartz, pyrite, chlorite, and ankerite, with locally abundant chalcopyrite and/or sphalerite. Exploration since 2004 has enlarged greatly the El Largo and the high-grade G-9 deposits, and slightly enlarged the El Rey deposit. The cumulative in situ massive sulphides for the Reforma, Naranjo, El Rey, El Largo, and G9 deposits exceed 45 Mt.

May 1, 2006

By Bhawani Singh, Mahendra Singh, N. K. C Samadhiya

"Inherently anisotropic rocks occur in abundance at many rock engineering project sites in Himalayan region. These rocks pose difficulty in analysis and design due to their direction dependent strength behaviour. Moreover the strength varies in a non-linear manner with confining pressure. Mohr- Coulomb strength criterion is widely used by geotechnical engineers for defining strength of rocks subjected to given confining pressure. However, the conventional Mohr-Coulomb (MC) criterion suffers from the limitation that the strength is treated to be linearly dependent on confining pressure. In the present article, the MC criterion has been modified by incorporating non-linear term while retaining the original parameters c and ?. The non-linearity with confining stress level has been imbibed through critical state concept (Barton, 1976). The criterion has been applied to a triaxial test data base comprising of more than 1140 triaxial tests conducted world-wide on anisotropic rocks. Statistical evaluation of the goodness of fit of the proposed criterion to the data-base has been carried out. Further the predictive capabilities have been evaluated by determining the error in estimation of triaxial strength if only few triaxial test data are available for determining the criterion parameters. The data base has also been back-analysed to assess the critical confining pressure for anisotropic rocks. Statistically the critical confining pressure, for the present criterion, may be taken nearly equal to 1.25?cmax, where ?cmax is the maximum value of the UCS out of all orientations of planes of anisotropy. It is concluded that reasonably good estimates of the anisotropic strength are possible through the proposed criterion.INTRODUCTIONMany rocks encountered in Himalayan region like shale, slate, schist and phyllite are inherently anisotropic and exhibit direction dependency in their strength behaviour. In addition, the strength of the rock also depends on the confining pressure and, the strength response is non-linear especially when the confining pressure may vary over large range. Conventionally, Mohr-Coulomb criterion is the most widely used criterion for rocks. However, the limitation of this criterion in its present form is that the strength is treated to be linearly dependent on the confining pressure. The present study attempts to address the following two main objectives: i) Include nonlinear response in the Mohr-Coulomb criterion while retaining parameters c and In their original form; and ii) consider anisotropic response of the rock for a given confining pressure. A nonlinear strength criterion, which uses shear strength parameters c and as per Mohr-Coulomb criterion, has been suggested based on critical state concept for rocks."

Jan 1, 2015

By Yun-Jie Wei

Seismic areas were in the eastern margin of the Qinghai-Tibet plain, whose structures were complicated, mainly composed of Maowen fault, Yingxiu fault and Pengxian-guanxian fault. The rapid rise of the Qinghai-Tibet plain led the crustal material of the eastern edge to move to the southeast along the faults on a large scale since the late Cenozoic; Minshan block structure and Long Men Mountain tectonic zone represented the strong nappe thrust movement as the east boundary of Chuanqing slip block; the stress was accumulating when squeezed, which to a certain extent resulted in breakdown of the crust, and earthquakes. The shock speed, high-energy accumulation, and the reversed dextrorotation of the earthquake fault characteristics et al. happened, which caused the development of secondary geological disastersts. According to on-site investigation, the typical geological disasters had thrust rock collapse, the instability deposit, the revival of potential debris flow et al. whose genetic model had been analysed.

May 1, 2009

By H. E. Pawson

Giant Yellowknife is located 600 air miles north of Edmonton on the north shore of Great Slave Lake in the Northwest Territories. In its 24 years of operation some 7,730,000 tons of ore have been treated to yield $175,000,000 worth of gold.The gold ore occurs at irregular intervals throughout a fold-like sericite schist zone cutting Precambrian rocks. The ore is characterized by 40 to 80% quartz - carbonate and about 10% pyrite and arsenopyrite. Considerable amounts of stibnite and antimony sulpho-salts are also present. Gold is finely divided in the native state existing in complex association with the sulphides. In most instances stibnite is barren but minor values are evident on occasion. Visible native Fold, quite prevalent in the early operating years, is, practically non-existent today. It was readily apparent from mineral dressing investigations conducted in .1944 that Giant ore would be difficult to treat. By 1948 a flow sheet had been established and operations began. In the ensuing years, changing ore characteristics necessitated modifications to some process steps and complete abandonment of others. By 1962 the major metallurgical problems were solved and all that remained was the refining of operating performance to its highest level.With one or two exceptions today's operation follows the practice established by 1962 (Fig. 1 - Flowsheet).

Jan 1, 1973

By Steve Wilkinson

"""Techniques for coarse-particle beneficiation of some gold ores and methods for determining potential for sorting any gold ore deposit.""With the advent of high speed computers, laser technology end different types of electronic sensing devices, ore sorting machinery has been developed, capable of handling significant tonnage rates while maintaining high level efficiency. Gold ores may be amenable to coarse-particle beneficiation where there exist measurable criteria upon which there can be recognition of auriferous versus barren lumps in the run of mine. Three types of criteria are suitable for sorting and are:i) Photometric - optical variance between ore and waste such as vein ores hosted by barren country rock;ii) Conductivity/Magnetic - based upon the metallic mineral content of ore end waste, and its association with Au, such as found in sulphide/arsenide Au ores,iii) Radtometric - detection of natural gamma activity occurring with uranium-bearirig gold ores.The method for determining the sortability of an ore depositconsists of, at least, three stages:i) Initial stage identification of ore and waste types,mineralogical/petrographical associations,amount of dilution in P.O.M.establishment of any sorting criteria]"

Jan 1, 1985

By F. Hassani, R. Mikaeil, B. Ferdowsi

Two analytical solutions for estimating the ovaling deformation and forces in circular tunnels are widely used in engineering practice, due to soil-structure interaction under seismic loading. This paper discusses the discrepancy between the two analytical and finite difference methods. A comparison of the two analytical methods shows that the calculated forces and displacements are identical for the condition of full-slip between the tunnel lining and ground. However, the calculated lining thrusts differ by an order of magnitude when considering no-slip between the tunnel lining and the ground. The analytical solutions are compared to numerical analyses of the no-slip condition using the finite difference method to validate which of the two methods provide the correct method. To achieve the goal, numerical modelling, field data of the Kuhin railway tunnel and Manjil earthquake characteristics are used. Numerical analysis results agree with one of the analytical solutions that provides a higher estimate of the thrust on the tunnel lining, thus highlighting the limitation of the other analytical solution.

Jan 1, 2008

By Steve R. McCutcheon, Cees R. Van Staal, John P. Langton, Leslie R. Fyffe

Abstract -The volcanic-dominated Tetagouche Group in northern New Brunswick contains numerous massive-sulfide deposits and intimately associated metalliferous sediments. The massive sulfides are generally hosted by Llanvirnian-Llandeilian volcaniclastic sedimentary rocks of the Nepisiguit Falls, Patrick Brook, and Boucher Brook formations. These formations are intercalated or closely associated with rhyolitic-dacitic flows and/or domes, and minor continental tholeiites of the Flat Landing Brook Formation. Pyroclastic rocks are relatively scarce in the silicic volcanic complex. Tuffites and epiclastic sandstones, of the Nepisiguit Falls and Patrick Brook formations, respective­ ly, generally occur along the fringes of the silicic volcanic complex. The flows and tuffites are intruded by quartz- and feldspar-phyric rhyolite (porphyry) dykes, sills, and domes. Although the volume of the silicic volcanic complex is large, evidence for a previously proposed collapsed-caldera model is lacking. On the basis of host-rock type and stratigraphic position, the sediment-hosted massive sulfides have been divided into three groups: the Brunswick-, Caribou- and Halfmile Lake-type deposits. Syngenetic feeder pipes and asociated alteration zones are generally not present beneath the Caribou- and the Halfmile Lake-type deposits and, if present at all, are poorly developed underneath the Brunswick-type.

Jan 1, 1992

By Steve R. McCutcheon, Cees R. Van Staal, John P. Langton, Leslie R. Fyffe

The volcanic-dominated Tetagouche Group in northern New Brunswick contains numerous massive-sulfide deposits and intimately associated metalliferous sediments. The massive sulfides are generally hosted by Llanvirnian-Llandeilian volcaniclastic sedimentary rocks of the Nepisiguit Falls, Patrick Brook, and Boucher Brook formations. These formations are intercalated or closely associated with rhyolitic-dacitic flows and/or domes, and minor continental tholeiites of the Flat Landing Brook Formation. Pyroclastic rocks are relatively scarce in the silicic volcanic complex. Tuffites and epiclastic sandstones, of the Nepisiguit Falls and Patrick Brook formations, respectively, generally occur along the fringes of the silicic volcanic complex. The flows and tuffites are intruded by quartz- and feldspar-phyric rhyolite (porphyry) dykes, sills, and domes. Although the volume of the silicic volcanic complex is large, evidence for a previously proposed collapsed-caldera model is lacking. On the basis of host-rock type and stratigraphic position, the sediment-hosted massive sulfides have been divided into three groups: the Brunswick-, Caribou- and Halfmile Lake-type deposits. Syngenetic feeder pipes and asociated alteration zones are generally not present beneath the Caribou- and the Halfmile Lake-type deposits and, if present at all, are poorly developed underneath the Brunswick-type.

Jan 1, 1992

By A. Esterhuizen, S. Essack, H. Joubert, N. Fowler

Tenova Pyromet has developed innovative technologies for copper smelting and electric slag cleaning furnaces. Based on client feedback and requirements, innovative designs have been developed to address key design areas and improve furnace reliability, operability and hygiene. These developments include the NovaLance™ lance system to prevent lance bending on top submerged lance furnaces, the SlagFlo™ slag tapping flow control device to better control bath levels and tapping rate for granulation, and an electrode seal for improved sealing directly onto the electrode casing to allow water-cooled electrode components to be located above the furnace roof. The potential application and benefits of these innovative designs are discussed. INTRODUCTION Tenova Pyromet has a long history in the engineering and supply of innovative electric furnace and related equipment for the base metals and platinum industries. Recently Tenova Pyromet has used its furnace equipment design experience to engineer innovative solutions for top submerged lance (TSL) furnaces, and potentially other furnace technologies. These equipment design solutions are developed to address specific operating challenges and operator requirements. Three of these innovative equipment developments are discussed in this paper. First the NovaLance™ lance technology to prevent lance bending during operation in TSL furnaces, such as used for primary copper smelting, is described. Lance bending has been identified as a significant problem for TSL furnace operators as it causes down time and affects furnace availability. The SlagFlo™ device to control the slag flow rate during tapping has been developed based on specific requirements in the mineral wool industry. The SlagFlo™ device can be used to control slag bath levels in primary smelting, converting and slag cleaning furnaces for base metals including copper. In addition, it can be remotely activated for the safe closing of slag tapholes located upstream from a water granulation system. Finally, Tenova Pyromet developed an electrode seal that seals directly onto an electrode surface. This is a special requirement related to base metals and platinum electric smelting and slag cleaning furnaces where furnace operators prefer to keep the water-cooled electrode equipment above the furnace roof. The seal can be used to seal directly onto the potentially hot and uneven surface of Söderberg, pre-baked and graphite electrodes.

Jan 1, 2019

By R. Le

"The principles of noise control aredescribed with particular emphasis on personalactive units as opposed to passive ear muffspresently in general use. A discussion followsfor their potential use in a mining environment.RÉSUMÉNous décrivons brièvement quelquesprincipes de contrôle de bruit à l’usage person-nel, puis nous passons en revue quelquescasques commerciaux dotés de ces circuits àprincipe actif. Enfn nous discutons de leurusage potentiel dans le contexte minier.IntroductionLe casque à principe actif est un produitqui existe commercialement, mais encore peurépandu en usage, sûrement à cause du prix,mais aussi de sa méconnaissance par le grand public. Il arrive parfois qu’un journaliste trouvele produit fantastique et le médiatise commeune réalisation de son pays (ou de sa province),mais peu savent qu’il s’agit là d’un principe quia commencé dans les années 30. Par delà lesensationnel, il reste que si l’on veut mettre lamain sur un de ces casques pour l’essayer, on nesait où l’obtenir. De plus, les casques n’utilisentpas tous le même principe actif. C’est la raisonpour laquelle nous faisons cette brève compara-ison. Nous le faisons en mettant l’accent pourune possible utilisation dans le domaine minier,car c’est dans ce milieu que les usagers sontconfrontés aux bruits les plus intenses qui peu-vent endommager leur système auditif, ce quin’exclut pas les autres situations (travaux publics, foresterie, écoute hi-f, etc.)."

Jan 1, 1997

By L. Garycki, P. Poks, R. Urbaniak, T. Gabka

In 2016 at Głogów Copper Smelter KGHM Polska Miedź S.A., after shutting down the shaft furnaces new FSF was launched. Currently, it is the only smelter with two direct to blister flash smelting furnaces in operation. The main difference between the vessels are the dimensions and production capacity. The new furnace design output is about 30% higher compared to the old flash smelting furnace working for 40 years. The paper presents a comparison of both FSFs operation, differences in technology and the way to optimize the process to maximize efficiency. INTRODUCTION KGHM Polska Miedź S.A. is the only company in Poland (eastern part of Europe) that extracts and processes copper ores. It is located in the south west of Poland and this region is called the "Copper Basin”. KGHM PM S.A. consists of three underground mines: Lubin, Polkowice-Sieroszowice, Rudna, concentrator plants, a tailings pond plant, three copper plants: Legnica, Głogów and Cedynia wire rod plant in Orsk. The publication relates to the operation of the furnaces in Głogów (the plant in Głogów consists of Głogów 1 and Głogów 2 which form integrated smelting and refining facilities). In 2016, after closure of the shaft furnaces technologies in the Głogów 1, a new FSF commenced operation. The simplified process flow sheets are given in Figure 1 and 2. Technological schemes are similar, but due to the differences in them, they will be discussed separately. Głogów 1 Enriched ores are discharged and directed to the feed preparation plant. Delivered concentrates are built up on the three bedding aisles in appropriate proportions. The concentrates are distributed in even layers in one of the three aisles. Aisle emptying is done with a blending machine which cuts across the concentrate layers and collects thus blended material, sending it via belt conveyors to a storage bin. From the cross- blending machine and conveyor assembly, the mixture of concentrates is directed to drying in the steam dryer. Part of the charge is directed to the FSF and part to the roaster for carbon elimination. Known in the world roasters are used to eliminate sulfur compounds or arsenic. In the case of KGHM deposits, the aim of the process is to reduce the energy value of the feed by eliminating carbon and converting sulfur from sulfide to sulfate. Changing the nature of exothermic to endothermic material is crucial in the case of furnace operation with design performance. Roaster is a separate furnace with an innovative character.

Jan 1, 2019

By William E. Stanley

The paper examines the problems that arise in undertaking socio-economic impact studies to meet the requirements of environmental-impact legislation governing new mine development or expansion. An approach to undertaking socioeconomic impact studies is outlined, responses to specific problems are discussed and ways in which the mining company can use these studies to meet its general objectives are explored. The paper concludes by examining how a socio-economic study, as required by legislation, can be used to assist the mining company in achieving some general objectives it will have in developing a mine.

Jan 1, 1979