Search Documents

By F. P. Hassani, H. B. Poorooshasb

"A kinematically admissible velocity field is applied to study the arching phenomenon in a cohesionless granular backfill placed between two rough vertical inflexible walls. The study is different from the previous works which are almost entirely based on statically admissible stress fields. It is shown that the development of arches is strongly influenced by the previous loading history of the backfill which controls the nature of the constitutive laws that govern the mode of stress deformation of the backfill. This preliminary study employs simple models in order to show the potential use of such an approach in evaluating and understanding mine backfill behaviour in the underground excavation. The pressure exerted on the floor supporting the backfill is also studied in some detail.INTRODUCTIONAlthough the importance of the design of mine backfill has been discussed extensively by a number of authors, i.e. Hassani et al. (1985), such theories have not as yet been incorporated in design criteria for underground mine backfilling operation . One factor that such theories must incorporate is the so-called arching action .The phenomenon of arching has been the subject of study by many researchers in the field of civil engineering and mining engineering. Among these scholars the works of Terzaghi (1943), Krynine (1945), Lusher and Hoeg (1964) and Handy (1985) are noteworthy. All these authors use a statically admissible stress field as a starting point to develop their theories. The approach taken by the authors of the present paper is completely different because they employ a kinematicallyadmissible velocity field. It is their belief that the arching phenomenon is closely linked to the interlocking of grains as manifested by the degree of dilatation of the granular mass when subjected to a shearing process.This paper is written in the following sequence. To define the interlocking quantitatively it is necessary to state the constitutive law governing the stress deformation characateristics of the granular mass. This is done in the next section as the law proposed by Poorooshasb and Pietruszazck (1985, 1986) is stated and simplified to suit the present analysis. Next the mode of formation of an arch in a simple system consisting of a mass of backfill sandwiched between two vertical rough walls of infinite extent is examined. The velocity field obtained from the above example is used to obtain solutions to two more complicated situations. The first situation assumes that the backfill is supported, in addition to the vertical rough walls, by a Winkler foundation at its base. The second situation assumes that the Winkler foundation has been replaced by a horizontal beam of uniform section and simply supported at its extremities. The findings of the study are summarized and their practical implications discussed in the concluding remarks."

Jan 1, 1989

By Roger Lacroix

Fuel cell application to mining has been indicated to be potentially beneficial to underground mine worker health and to energy efficiency. In order to define the economic advantages of using hydrogen fuel cell vehicles, a detailed study of operating and capital costs associated with underground loaders and power supply infrastructure has been carried out. The results show that for a typical medium-size mine, operating costs and infrastructure costs are less for the fuel cell option versus diesel. The reverse occurs for capital costs owing to the currently higher cost of fuels cells versus diesel engines. This disparity is expected to decrease given the decline in price associated with fuel cell technology advances. Related market issues for fuel cell manufacturers are also presented. Despite the difference in cost, the resources and mine infrastructure required to operate loaders, and base design of the mine loader, is similar for diesel and fuel call versions.

May 1, 2007

By Shahram Tafazoli

ABSTRACT: This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By W. F. Giuvlore, E. Mcroberts, T. S. Golosinski

"The rising demand for Canadian coal and depletion of shallow deposits, most suitable for surface mining, result in rapidly increasing volume of waste materials which have to be moved by the coal mining industry. While at present this challenge is being successfully met using conventional mining methods, in the future, innovative methods must be considered if Canadian coal is to remain competitive.The need for more efficient mining methods is also faced by the oil sands industry to assure competitiveness of the synthetic oil price.A look at the world mining practice indicates that large volumes of material can be economically mined and moved by the continuous mining systems comprising bucket-wheel excavators, belt conveyors and stackers. To assess the state of art and applicability of this mining method to Canadian conditions, the field trip was organized by the Department of Mining Engineering o f the University of Alberta, to several typical mining operations in Europe. It is in Europe where the continuous mining methods were developed and are almost exclusively used in large-scale surface mining."

Jan 1, 1984

By B. Haugrud, E. McConaghy, M. Collins, G. Smith

"Laterite ore processed by the Ambatovy Joint Venture in Madagascar is primarily limonitic in nature, containing about 40 to 45 wt.% Fe and 1.1 wt.% Ni. The process selected for treatment of this ore considered the behavior and deportment of iron in each step of the commercial flowsheet. Such considerations included nickel and cobalt recoveries, reagent consumptions, liquid-solid separation characteristics, and both intermediate and final product purities. In this paper, the results for the first three years of commercial operation at Ambatovy are compared with the design parameters, with emphasis on the behavior of iron.INTRODUCTION The main component of nickeliferous laterite ore is iron, and the Ambatovy deposit in Madagascar is no exception. The Ambatovy ore is primarily limonitic in nature, containing about 40 to 45 wt.% Fe and 1.1 wt.% Ni. Since the nickel content of the ore is roughly one fortieth that of iron, successful recovery of nickel depends on close control of the behavior of iron in the selected process. Exploration of the Ambatovy area, which is located to the east of Antananarivo, the capital of Madagascar, dates back to 1960, when the Malagasy Service Géologique carried out a limited pitting and auger-drilling program. Phelps Dodge Corporation (now Freeport-McMoRan Copper & Gold, Inc.) was granted the mining rights to the property in 1995 and carried out significant resource definition, environmental assessment and engineering studies between 1995 and 2001 (Chou, Rooke, Williams, & Hanks, 2000). In 2003, Dynatec Corporation, which was formed in 1997 by the merger of Dynatec International Ltd. and Sherritt International Consultants Inc., signed a joint venture agreement with subsidiaries of Phelps Dodge to evaluate the Ambatovy Nickel Project. Dynatec then became extensively involved in the development of the project, including process selection and pilot plant testing in Fort Saskatchewan (Collins et al., 2004, 2005, 2009; Collins & Vardill, 2005). Dynatec acquired 100% of the project in 2005 and a joint venture between Dynatec, Sumitomo Corporation, Korea Resources Corporation (KORES), and SNC-Lavalin Inc. (SLI) was formed shortly thereafter to provide funding for further development. SLI was responsible for engineering, procurement and construction management of the commercial facilities. Sherritt International Corporation reacquired Dynatec Corporation, including 40% ownership in the Ambatovy Nickel Project, in 2007. The current Ambatovy Joint Venture consists of an integrated nickel and cobalt mining, processing, refining and marketing enterprise between subsidiaries of Sherritt (40% owner and mine and plant operator), Sumitomo Corporation (32.5% owner) and KORES (27.5% owner)."

Jan 1, 2016

By Andrea M. Ouchi

A major focus of ground control research presently being conducted by the Geomechanics Group in the University of British Columbia Mining Engineering Department is to incorporate weak rock masses (RMR76 less than 50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented by mapping of one mine in Montana and of several mines within the Carlin and Getchell Trends of Nevada. In addition, a neural network analysis has been performed and modifications of the span design curves at the lower RMR76 range have been made. The common factor in all the above mentioned mines is a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be dealt with to safely extract the mineral bearing rock. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

May 1, 2004

By John Wilson

"The Rietveld numerical method was used to calculate the relative abundances of phases in both synthetic binary mixtures and synthetic and natural ores, using X-ray diffraction data. The results were compared with those of image analysis and a chemical method. The ranges of the relative errors were estimated. The Rietveld method is found to be acceptable for determining the abundances of major and minor phases and the amorphous component of partially crystalline samples. In complex mixtures, where there are several trace phases (~<2 wt%) present, the technique becomes less accurate. It is most useful as an alternative technique to image analysis when sample preparation is problematic or sample particle sizes are sub-micron. It is a manual method which requires user input during the fitting process, but is both simpler and faster than image analysis due to the reduced set up time and sample preparation required. It is now implemented at CANMET as a technique for quantitative analysis.INTRODUCTIONUntil recently, the Applied Mineralogy group at CANMET used only image analysis and chemical techniques to determine phase quantities. An effort to develop quantitative X-ray diffraction (XRD) has been on-going for several years. Initially, the reference intensity ratio (RIR) method with external standards was tried with some success (Szymanski and Petruk, 1989). The main difficulty with this technique was finding adequate standard material for each phase present in the sample. This shortcoming made the method ultimately impractical, given the wide variety of materials which come to the laboratory for analysis.The Rietveld refinement method of quantitative XRD (Hill et al 1993, Mumme et al 1996), in contrast, requires no standards and requires minimal sample preparation and therefore a more rapid turnaround compared to image analysis. The Rietveld method also has advantages over image analysis in that it can identify and quantify polymorphs, ultra fine materials and many types of hydroxide products. As well, it is useful for analyzing materials such as bauxite or talc, which do not polish well enough for making mounts of the quality required for image analysis. To quantify amorphous material and phases which are present in amounts below the detection limit of XRD, the addition of a standard material is still required. However, in such cases only one standard is needed, which is alumina."

Jan 1, 2003

By Jehan Rondot, Raymond Marleau

"Des quartzites trés pars ont été découverts au cours de la cartographie de la region du lac des Martres, étape de l'étude géologique de la region de Charlevoix.On distingue quatre groupes métasédimentaires, tons con tenant des niveaux de quartzite dans an mains deux domaines géologique différents, c'est à l'ouest, clans le do¬maine gneisso-charnockitique que se situent les quartzites du groupe des Martres. Quartzite et gneiss à, grenat et sillimanite, en banes épais, constituent la formation de La Galette. A Pest, dans un environnement gneisso-granitique, les deux groupes métasédimentaires de Saint-Siméon, et de La Malbaie comprennent, par contraste, des bancs pen épais et de compositions variées. Les niveaux de quartzite dépassent rarement 50 m d'épaisseur. L'autre groupe métasédimentaires, celui de Saint-Tite des Caps, recoupé de nombreuses intrusions charnockitiques et granitiques, ne possède que de minces niveaux de quartzite.La pureté et la grande épaisseur des quartzites de La Galette suppose une histoire complexe qui se termine par des depots continentaux de climat aride, par opposition aux depots marins des autres groupes. D'autre part, la presence de ces quartzites an sein de roches Presque anhy¬dres et de haute temperature que sont les charnockites leur confére des caractéristiques de fusion sans decrepitation.Parmi la multitude de depots de quartzite qui existe clans le monde, peu sont de qualité supérieure. Or, de par sa composition chimique, le quartzite de La Galette se compare avantageusement à ceux des meilleurs gisements des Etats-Unis, de l'Europe de l'Ouest et de l'Afrique du Sud. D'accès facile pour l'exploitation, les gisements ne sont qu'à une trentaine de milles de Baie Saint-Paul ou de La Malbaie, sur le Saint-Laurent.L'utilisation en metallurgic prévue pour le quartzite de La Galette comprend la production de silicium, de ferro¬silicium et d'autres alliages de silicium. La composition du quartzite est en outre appropriée pour la production de carbure de silicium et de silicate de sodium. Les fines peuvent être utilisées pour la fabrication du verre et comme matiere de charge"

Jan 1, 1977

By P. Hickey, A. Oliver

"In March 1993, Ram Raising Limited was faced with a challenge. Placer Dome Incorporated, Dome Mine Division requested from Ram Raising that they design station excavation into the existing No. 8 shaft from No. 3 mine levels. This work had to be done without loss of production time in the underground department.Due to the time frame of the project, every detail had to be carefully considered, with extra care that all pros and cons had been worked out.Ram Raising submitted a work Plan that had been worked out with the Redpath Group which included the infrastructure requirements; the engineering design; the scheduling and sequence of work; and the excavation design and blasting procedures.A proposal was&apos; put together by both Ram Raising and Placer Dome outlining the infrastructure requirements, including the engineering design, scheduling and sequence of the work, excavation design and blasting procedures. The proposal accepted by Placer Dome and, on July 3D, 1993 work commenced to breakthrough eight stations. Work continued until December 1993 with the completion off our stations. The project was then stopped to allow the station access drifts from No.3 mine to be completed. The second phase of the project began on May 27 and was completed on September 15, 1994.This paper shows how, through innovative design and the full cooperation between client and contractor, a project of this nature can be completed successfully."

Jan 1, 1995

By John E. Udd

"In this paper the author presents the results of the 1992 CIM survey of graduates in minerals and technology programs in Canadian post-secondary institutions. As usual, the trends are out-of phase with the economic state of the industry. People who chose a minerals career in the prosperous days of the late 1980sare now entering a labour market in recession.The cyclical nature of enrollments is illustrated in a series of figures showing the trends since the CIM survey Wa5 begun in 1956 (and even earlier for mining engineering).In the survey, the respondents were asked to provide comments on their perceptions of the problems specific to minerals education in Canada. The large number of responses have led the author to the conclusions and recommendations given in the final part of the paper."

Jan 1, 1993

By J. A. Hudson

"The paper begins with a brief summary of Professor Müller’s formation of the ISRM and the contents of the previous six Müller lectures with their emphases on rock fractures. The geological origin of fractures is described via a deformational spectrum diagram and a matrix characterising the consequences of a sequence of superimposed deformational events. The different fracture frequencies encountered along lines in all directions through a fractured rock mass are explained. The value of computer modelling and simulation is demonstrated through an example of the effects of fracture zones on the distribution of the in situ stress field. The need to establish the validity of computer programs, i.e., that the modelling/simulation, does actually represent the rock reality, is discussed with reference to the work of the DECOVALEX project. Finally, examples are given of the effects of rock fractures on engineering design and construction, from pre-split blasting to caverns.INTRODUCTIONIt is a great honour to have been chosen as the recipient of the ISRM 7th Müller Award and I am grateful to the representatives of the International Society for Rock Mechanics (ISRM) National Groups who voted for me. In addition, I am especially pleased because my working life in rock mechanics and rock engineering has been devoted to understanding the geometry and mechanical properties of rock fractures and rock masses—which were the key subjects that Professor Müller promoted. In the ISRM 50th Anniversary Commemorative Book, Hudson and Lamas (2012), Professor Charles Fairhurst notes that on 24 May 1962, i.e., the day before the constitutional meeting of the ISRM took place in Salzburg, a reporter asked Professor Müller, “Do we know the strength of rock?”, to which Professor Müller replied, “For rock tested in the laboratory, yes. For a rock mass, no. This is what we need to determine. This is why we need an International Society for Rock Mechanics”. Also, in his Opening Address at the 1st ISRM Congress in Lisbon, Professor Müller, as the then ISRM President stated,“Many experts agree with me that discontinuity and anisotropy are the most characteristic properties of the material rock and that the properties of jointed media depend much more upon the fabrics bond of the unit rock block system than upon the rock material. Therefore any theoretical investigation of that material has to go its own ways, in the same way as the construction material of soils years ago suggested to soil mechanics its own methods, which differ greatly from the way of thinking of technical mechanics”."

Jan 1, 2015

By F. Halverson

"The theory of flocculation usually is in a state of flux, involves many diverse phenomena, and is complex and sometimes contradictory in details. Instead of attempting a general discourse, I shall discuss selected observations made at our Stamford Laboratories, which impinge on theoretical aspects in two somewhat distinct areas of flocculation. Since some of you many not be familiar with flocculation, and :.n order that we all attach the same meaning to the jargon used, I first would like to review briefly a generalized picture of what goes on.Assume we have a suspension of particles in water, with a distribution in the sizes of particles. The surfaces of the particles interact to some extent with the water--· tending to alter the extent of hydration, may generate some ion exchange, all being somewhat variable with time--developing a surface condition which is very complex in details. We refer to this suspension as the ""substrate.""In the usual situation, if the suspension is allowed to stand quietly, the large particles settle out first, with somewhat smaller particles settling more slowly, and then there is a portion of very fine material which takes a long time or doesn't settle out at all. This resistance to settling t~ the very fine particles results from many factors, but all relate back to the size and density of the particles, to their surface properties, and to the other components in the aqueous suspending medium."

Jan 1, 1978

By B. Tanda

A process has been developed at Curtin University whereby glycine is used in an alkaline environment to leach gold, silver and copper from their ores, concentrates, process intermediates and wastes. Copper mineralisation investigated includes various oxides, sulfides and native copper. The leach process utilises an oxidising environment such as oxygen. Glycine is a non-toxic, non-volatile, edible, low cost reagent which is produced in large industrial quantities for use in several industries. Glycine and its copper and precious metals complexes are stable over wide pH, Eh and temperature ranges. Other than losses in leach residues, the glycine is recovered and recycled for leaching. Iron dissolution is insignificant in the pregnant leach solution. Iron in pyrite remains unaffected, whereas iron associated with base metal sulfides (e.g. chalcopyrite and bornite) is converted to a readily filterable iron hydroxide. Efficient separation of copper by solvent extraction and conventional electrowinning has been shown to be feasible for a number of organic extractants, whereas gold and silver glycinates adsorb very well onto carbon allowing CIP/CIL/CIC (carbon-in-column) based processes. The process is ideal for ores containing acid-consuming gangue, concentrates with high arsenic or halide contents and for copper-gold ores with significant sulfide mineralisation. The process eliminates many of the problems associated with the processing of copper-gold-silver ores, such as elemental sulfur formation, silica gels, unwanted metal co-dissolution, and jarosite precipitation. The reagents used and process residues are much safer and environmentally benign than conventional process options. The processing technology can be applied to in-situ, heap and vat, or agitated tank leaching at temperatures ranging from ambient to below 100?C at atmospheric pressure and is currently being commercialised. This paper will focus on copper leaching and recovery and iron rejection from a chalcopyrite flotation concentrate.

Jan 1, 2016

By P. Mark. Hawley

Development of Barrick Gold?s Pierina Gold Mine in north-central Peru requires construction of a waste dump for disposal of non-ore grade materials stripped from the open pit to expose the ore. The waste dump site is located near the open pit in a U-shaped valley that is underlain by thin colluvial and morainal soils with locally thick peats and glaciolacustrine deposits. Bedrock underlying the site consists of variably weathered volcanics. The site is subject to moderately high seasonal rainfall and significant seismicity. The geotechnical quality of the waste rock is highly variable, ranging from low quality, degradable, soil-like materials containing appreciable quantities of silt and clay, to high quality, hard, durable, blocky waste rock. A hybrid dump design concept was developed that requires in-pit segregation of high and low quality waste, and selective placement of materials in the dump to maximize stability and enhance internal and subsurface drainage. The design includes a rock drain beneath the dump along the axis of the valley and a series of connected finger drains. Extensive peripheral diversions and stormwater control measures to inhibit infiltration of precipitation are also included. This paper discusses the unique challenges presented by the site and waste materials, the design methodology and stability analyses, and planned monitoring systems.

May 1, 2002

By Carl O. Nickle

"IntroductionIF I WERE ASKED what are the two most important single factors in shaping the growth of Canada to date, and in building its future, the answer would be: first, the treasure house of natural resources on and below the surface over the length and breadth of our country; and two, the pioneering spirit and 'get up and go' of many of our people. The two factors are inseparable. Without the pioneering spirit, the natural resources of land, forest, stream, and the subsurface would have continued •to be useless,. Idle assets. With the pioneering spirit, Canada's natural resources have been and are creating economic revolutions.Western Canada oil and natural gas rank high on the list of such revolutions. Calgary, your meeting place today, is the birthplace of this economic revolution, one that has already sharply altered the economy .of the middle half of Canada, particularly that of Alberta; is increasingly making its weight felt on the economy of all Canada; and is helping re-shape world thinking on sources of vital petroleum supply for both peace and war. Calgary is today the 'operation headquarters' for the great bulk of a huge exploration and development programme that now extends over a quarter of a million square miles of Canada's West. As a Calgarian, •therefore, I am particularly happy to have this privilege of talking about oil and natural gas to members of the C.I.M.M., who play a key role in the development of all Canada's varied natural resources."

Jan 1, 1952

A rough simulated borehole has been developed for the installation and dynamic testing of rock bolts a the WASM Dynamic Test Facility. The rough simulated borehole is used for rock bolts that are sensitive to equipment installation technique or borehole geometry (particularly friction rock stabilisers and resin encapsulated bolts). An extensive axial test program has quantified a difference between the static and dynamic capacity (kN/m of embedment) for friction rock stabilisers once sliding starts. The 47mm split tube bolt has a 50% reduction in embedment capacity (but with significant variation) dissipating 2.7kJ/100mm of sliding per meter of embedment, and the Omega (inflatable) bolt had a 70% reduction in embedment capacity dissipating 6.2kJ/100mm of sliding per meter of embedment. The Omega bolt dynamic capacity remainder at least equivalent to the split tube bolt static capacity.

May 1, 2009

By A. Himsley, E. Byleveld

"With reference to the chemical constraints underlying the ion exchange process for uranium recovery, a generalized view is presented on the actual and the achievable efficiency of the process. The area considered is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution.A comparison between actual plant results and the chemical requirements shows that:(a) Unless new and better ion exchange resins are developed, no dramatic change in equipment size and resin inventory is""anticipated. (b) Elution efficiency, especially for sulphuric acid, may be improved considerably. More concentrated eluates may beproduced at lower chemical consumption. A possibility of achieving additional purification solely by ion exchange is discussed.IntroductionThis paper presents a generalized view of the actual and the achievable efficiency of the ion exchange processes for urannium recovery. The study is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution. The ultimate efficiency attainable with ion exchange is dietacted by the chemical reactions underlying the process. The most sophisticated technology cannot change the diffusion rates in the ion exchange resin nor make the uranium loading exceed its equilibrium valueThe design of an ion exchange plant for uranium recovery involves a considerable number of parameters as a result of the wide variety of pregnant solutions produced from different orebodies. Therefore, a generalized approach of the ion exchange process inevitably neglects some parameters which maylead to significant variations in apparently identical situations.The uranium concentration in the pregnant solution, together with its pH, are the principal variables which determine resin loading and residence rime in the ion exchange system. On the elution side, the type of eluant and its concentration will determine the contact time required and the amount of eluant needed to strip the resin. The temperature, the properties of the ion exchange resin, the total dissolved solids in the feed solution and the competing ions are other variables that affect the chemical performance; these, however, may be considered as a correction of the principal parameters if one is interested only in general trends."

Jan 1, 1980

This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. Basis of operation of the PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, online technologies through review of published information available for on-conveyor minerals applications. Case studies demonstrate benefits provided by this technology in two operating mines. An iron ore company had prior experience with the PGNAA analyser technology, implementing an early model in a minerals application in 2003 to develop confidence in its measurement performance and usefulness of the data. A number of analysers were subsequently included throughout the new plant design for extensive measurement and control of conveyed bulk flows, from conveying after mining through to rail load-out. A copper-gold company installed an analyser to address copper ore blending issues where an on-belt system was the only viable option for the degree of control required. Analyser suitability was evaluated through test work on site samples to determine customised multi-element precision guarantees for each application. Analyser results from normal operation are compared against laboratory analyses of multiple cross stream samples collected from conveyed flows to assess performance. Both projects discussed were able to realise benefits previously unattainable for plant quality control, surpassing capabilities of traditional technologies which were either unsuitable for measuring conveyed flows with adequate accuracy or in real time. Equipment payback within a few months was achieved for both sites. Through proven performance in these applications, the companies consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.

Jan 1, 2014