Search Documents

By H. Cay, J. Zachwieja, T. Esplin, R. Ravenelle, T. Olsen-Tank

Barrick Goldstrike mine utilizes a carbon-in-leach (CIL) circuit to simultaneously leach gold into solution with cyanide and adsorb the gold-cyanide complex onto activated carbon for further refinement. If the gold bearing ore contains a significant amount of native carbonaceous material, gold cyanide can be adsorbed at these sites instead of onto the desired activated carbon and the gold is effectively lost to tailings in a detrimental process known as "preg-robbing." The preg-rob effect is considerably reduced by treating the ore with a surfactant, which is hypothesized to adsorb to and passivate the native carbon surfaces. Past laboratory and pilot studies have consistently demonstrated significant gains in gold recovery after treating carbonaceous ore with surfactant. With success in bench and pilot scale testing, a plant trial was conducted at Barrick Goldstrike to evaluate the feasibility of using an alkoxylated fatty amine surfactant (Ethomeen T/12) to aid in the leaching of high preg-robbing ores. This paper analyzes the performance of the surfactant during the plant trial in addition to the problems that occurred during the trial period. Suggestions for improvement are also discussed.

Jan 1, 2014

By Charles G. Kemsley

IN January, 1939, Dome Mines, Limited, purchased a few bars of an alloy drill-steel for the purpose of testing its fatigue resisting qualities as compared with those of a straight carbon-steel then in general use at the mine. A steel of the following analysis was selected: Carbon 1.00% Sulphur 0.022 Chromium 1.26 Silicon 0.17% Phosphorus 0.028 Vanadium 0.1 Manganese 0.32% Molybdenum 0.30 This steel has a tensile strength of 180,000 lb. per square inch and a Brinell hardness of 380, as compared with a tensile strength of 114,000 lb. per square inch and a Brinell hardness of 230 for the standard carbon drill steels, in the as rolled' condition. The result of this test showed that about five times as many runs could be obtained from the alloy steel before failure from fatigue. It was therefore decided to replace gradually the one-inch quarter-octagon carbon steel, then in use, with seven-eighths quarter-octagon alloy steel. In January, 1940, six machines was placed on the seven-eighths steel and this was gradually increased until now (March 15th, 1941) fifty per cent of the steel being used is alloy steel. An O'Donovan furnace is used at the Dome for heat-treating their carbon drill-steel. In this furnace, a magnet withdraws the steel when the critical temperature has been reached, and the operator then places the steel in the quenching tank. Not being able to use this furnace for the alloy steel, the management felt that some means should be developed to determine the quenching temperature without depending upon the operator's judgment of the correct 'colour'. With the assistance of the Canadian General Electric Company, a radiation-type vacuum thermocouple pyrometer was adapted to this purpose, with excellent results; in fact, with this instrument no previous experience in hardening is necessary and results are remarkably uniform.

Jan 1, 1941

By W. P. Clement, M. C. Bell

"PT International Nickel Indonesia, a subsidiary of Inco Limited, mines and processes nickel laterite ores for the supply of nickel matte, primarily to the Japanese market. It has large ore reserves and a substantial portion of its energy requirement is supplied from its own hydro-electric plant. Since the early 1980s, the company has increased its production level and has dramatically reduced its unit costs. Projects are in progress to further decrease costs and recently a major expansion - 31% increase in nominal capacity - has been undertaken, consistent with marketing opportunity in Japan. The expansion project, which has a low capital cost per unit of production, is outlined in this paper.IntroductionPT Inco is a fully integrated mining and smelting facility located in Indonesia on the island of Sulawesi, and is based on a very large, world class nickel laterite orebody located 60 km inland from the Gulf of Bone. Construction of a single furnace line plant started in 1973. Complete supporting infrastructure of townsite, hospital, schools, shopping centres, road systems, and an airport, all had to be built. Prior to completing the first phase, the decision to expand the plant to a three kiln-furnace line was made. A major factor in the decision was the ability to develop the hydroelectric potential of the nearby Larona River. This involved construction of a 30 m high dam, and a 7 km surface canal to the generating station. The penstocks drop 150m to three 55 Mw turbines. The power generated is sufficient to supply the entire electrical load for the complete smelting complex and town site. The unique capability to supply the high smelting energy requirements for a lateritic nickel ore by fully captive hydro power, has, over the past decade insulated PT Inco from the large upward swings in oil prices suffered by other lateritic nickel producers.Wet ore is first partially dried to 20% moisture in two co-currently fired rotary driers, screened on an internal trommel, and delivered to two dry ore storage buildings. The partially dried ore is calcined at 750°C and partially reduced in three large 100 m by 5.5 m kilns. Reduction is accomplished by lancing bunker C oil onto the ore bed at the discharge end of the kiln. The kilns are equipped with five air pipes with onboard blowers to gradually bum the combustible gases generated by the lance oil. The kilns were also originally equipped with two side burners to supply additional heat close to the feed end of the kiln. Calcined ore is transferred by 20 ton refractory lined containers to the furnace feed bins at the top of the smelter. Smelting is carried out in three 18 m diameter furnaces powered by 45 Mw transformers. Slag is skimmed at 1550°C through water cooled breast plates and removed to the slag dump by Haulmaster Carriers. Matte of 25% Ni, 1O% S, 65% Fe is tapped at 1350°C into the converter aisle. The iron is slagged in converters to produce a nickel sulphide matte at 80% Ni. Three rotary Kaldo converters were initially installed. The product matte is granulated, dried, and shipped in returnable rubber bags to Japan. Most of the matte is fluid-bed roasted to nickel oxide and then directly reduced in a second reducing fluid bed reactor at our facilities in Japan.The smelting complex was designed to smelt two million tonnes of dry ore per year, equivalent to 34 000 tonne nickel production at an ore grade of 2% Ni. The cost of the entire project including working capital was $900 million."

Jan 1, 1990

By H. M. A. Rice

"The Ainsworth mining camp is on the west side of Kootenay lake; British Columbia; 14 miles south of the town of Kaslo. It is in one of the oldest mining districts in central British Columbia; for mining started there in 1888. Its principal production was between 1905 and 1920. Activity since then has been sporadic. According to available records; some 222; 000 tons of ore had been produced from the camp up to 1942.GENERAL GEOLOGY Bedrock in the district consists of a succession of quartzite, quartz-mica schist, hornblende schist, and limestone of Late Precambrian, Carboniferous, and Triassic age. Most of the hornblende schists are of volcanic origin but some formed from related intrusions. The Nelson granodiorite batholith of Jurassic age borders the camp on the west. There is also a series of basic dykes of much later age."

Jan 1, 1954

By Tracy-Lynn Humby

A recent report commissioned by the South African Chamber of Mines, Mining Vision 2030, identifies the South African mining industry?s negative legacy, its exploitation of people and the environment, as the single biggest hurdle to maximizing the industry?s impact on national development. Industry leaders have identified the need to put the past ?to rest?. With reference to three recent cases involving members of the South African mining industry, this paper points to the continuities between the past and present. It argues that the metaphor of ?multiple crossings? is more generative than the notion of putting the past ?to rest? for purposes of engaging with mining?s negative legacy.

Aug 1, 2013

By J. F. Henderson, N. H. . C. Fraser

"Camlaren Mines, Limited, owns a group of claims near Gordon lake, in the Northwest Territories about 45 miles northeast of Yellowknife. The Hump vein on the property was explored continuously from the summer of 1937 to December, 1938, when all work was stopped. The two-compartment vertical shaft sunk near the vein is 380 feet deep and drifts and cross-cuts on the 200- and 350-foot levels total 2,241 feet . This exploration indicated 13,177 tons of ore with a gold content of between ½ and 1 ounce a ton1GEOLOGY AND STRUCTUREThe property is underlain by remarkably fresh greywacke and slate of the Early Precambrian Yellowknife group. The thickness of the b ~ds averages 1 to 2 feet, although that of the coarser greywacke may be 10 feet or more. Most of the greywacke beds show a gradation in grain from sandy at the base to slaty at the top. They are composed of chlorite, sericite; carbonate, and detrital quartz and feldspar grains.The structure of the greywacke and slate underlying a part of the property of Camlaren Mines, Limited, is shown in Fig. 1. The beds are isoclinally folded so that they dip at steep to vertical angles and at many places are overturned. The axes of the folds are 50 to several hundred feet apart, and generally plunge at angles of 45° or steeper. The beds along the axes of the folds generally meet to form a sharp V, and at the point of the V, or axial part of the fold, the beds are commonly ruptured . Minor faulting movements along the broken crests of the folds in many cases result in well-defined shear zones. Discontinuous quartz veins and irregular lens-like masses of quartz lying more or less parallel with the bedding are plentiful throughout the sediments, but tend to be concentrated along the ruptured and sheared, anticlinal and synclinal fold axes ( Fig. 1)."

Jan 1, 1954

By M. Lytle

"The Corbin area of southeastern British Columbia has been a coal mining area since 1908. Byron Creek Collieries Ltd. Has operated its Coal Mountain Mine in this area from 1974 until the present. In February 1981, this company was purchased by Esso Resources Canada Ltd.Coal Mountain is structurally complex and standard computer algorithms are not applicable to model the overturned synclinal structures and faulted bedding surfaces. This paper discusses two approaches used by Esso Resources staff to model the geology of Coal Mountain.The first approach projects digitized cross-section data along trend to develop a large data base which correctly approximates the shape of the structure. The spatial orientation of the structure is corrected by merging the generated data set with drill-hole data. The second approach uses digitized cross-section and bench-plan geology to generate a block model of the coal reserve.HistoryThe Coal Mountain Mine, also known as the Corbin Mine of Byron Creek Collieries Ltd. is located 24 kilometres south of Highway 3 in southeastern B.C.In 1905, two American businessmen recognized the coal potential of the area during a horseback tour. The two businessmen, D.C. Corbin and E.J. Roberts, formed the Corbin Coal and Coke Co. to mine and market coal from their newly acquired 6075 hectares of coal licenses. By 1908, the town of Corbin was under construction, a 22.4-km rail spur was constructed from the mine to the main CPR line and the first underground mine began to produce coal. An open-pit operation was also developed at the 1828-metre elevation using a steam shovel loading into rail cars. The company operated continuously until 1935, when a lengthy strike forced suspension of operations.In 1943, the Consolidated Mining and Smelting Company Ltd. (now known as Cominco Ltd.) operated two surface mines to produce coal for its smelters at Kimberley and Trail, B.C. This operation ceased in 1948."

Jan 1, 1982

By J. G. Strasser

"There has been considerable output over the last three decades from the social sciences concerning man and his working environment. In the mining industry at large, however, authoritarian, hierarchical control systems remain the norm, and it can be argued that something less than optimum effectiveness in terms of both productivity and worker satisfaction has resulted.Recently (/975), Campbell Chibougamau Mines Ltd. devised a most interesting organization and incentive system that links the underground production of a standard ton of mined output at controlled grade to an incentive payment scheme. A parallel scheme in the mill complex is based on maximizing recovery of copper and gold from available feed. A key part of both minsystems is the formation of groups who have considerable autonomy, particularly when compared to the still prevalent traditional mining industry relationships between the worker and supervisory levels.This paper traces the development of Campbell Chibougamau's system . Attention is drawn to qualitative and quantitative measures of the success of the method through the commentary of those miners involved in the scheme, and by reference to the favourable records on productivity, absenteeism, safety, turnover and grievance activity.IntroductionPyramidal or hierarchical management control systems, coupled to piece-work incentive schemes, predominate throughout Canada's underground mining industry. Although specific details of such systems vary from site to site, they , are generally understood and accepted as fact by the majority of the work force.Normally, a front-line supervisor (shift boss) directs a number of workmen and assigns them to tasks and working locations commensurate with their abilities, knowledge, training and skills. This front -line supervisor may direct or supervise from as few as 12 to as many as 75 or more workmen. He issues orders according to his assigned production objectives and ensures that these directions are fulfilled in accordance with standard mine practice . Several shift bosses are usually directed by a mine foreman or mine captain. The mine captains report to a general foreman or directly to the mine superintendent or his assistant, depending on the size and scope of the operation."

Jan 1, 1981

By R. Amelunxen

"The molybdenite associated with copper porphyry ores is generally treated in a flotation circuit consisting of a separation and a cleaning section. In the last few years column flotation cells have replaced the numerous counter-current stages that were previously used in the cleaning section. Despite this, little has been published regarding the number of column cleaning stages required. Therefore a Moly flotation database is assembled with the objective of verifying the existence of a common upgrading profile. This can then be used as a guide in the prediction of the number of stages required to achieve a given concentrate grade.INTRODUCTIONAlthough the first use of Column Flotation was on copper flotation products, the popularity and understanding of their operation was not really achieved until they were widely implemented in Moly circuits in early 1983. The use of columns in Moly plants has since left a legacy of information, both published and unpublished. The data collected since that time has been used primarily used to establish column operating parameters and to determine upgrading potential within the circuit.Byproduct Moly generally occurs with porphyritic copper ores in concentrations less than 0.1% MoS2. As such, piloting a new moly ore to produce, say 5 Kg/Hr MoS2, in a slurry approximately 1 Lt/min (at 10% solids), requires a moly plant feed of about 570 Kg/Hr, which translates to a mill feed rate of 200 to 800 Tonnes per day (depending whether you deal with Chilean or Canadian ores). Piloting Moly for any lower tonnage would reduce the accuracy of the testwork.Thus a need exists to collect operating data in order to establish the existence of process relationships that could be used for feasibility and design purposes.The object of this paper is to expose a preliminary relationship that could be used for the purposes described above and to apply the findings to a preliminary design of a moly cleaning circuit flowsheet."

Jan 1, 1990

By John D. Carriere, Jean Leung, Daniel. Laguitton, Michael .. J. Burrows

"The objective of this expert system application in a copper-zinc concentrator, is to increase the availability of assay data through substitution for erroneous data. The assay data is used by the Operations personnel and automatic process control strategies to control flotation circuit performance. Two online X-ray fluorescence analysis systems analyze 24 streams across four divisions to provide the required data. Data availability of individual streams average 90% while the resulting circuit availabilities are 70%. The unavailability of correct data results from mechanical, X-ray or process problems. The erroneous data can be identified by process experts using knowledge relating stream interdependencies and historical process behaviour. An expert system was devised to provide real time identification of erroneous data and substitute for that data with the ultimate aim of improving metallurgical response by both the operator and automatic control systems.The paper discusses the early development work and architecture of the knowledge base designed using Neuron Data's expert shell NEXPERT.INTRODUCTIONThis paper describes the early development of an expert system (ES) prototype at the Kidd Creek concentrator. The project is a joint undertaking of the Kidd Creek Division of Falconbridge Limited and CANMET. Kidd Creek entered into the project to apply heuristic rules to the XRF assay data to improve the metallurgical control of the flotation process by increasing availability of analysis data. This project provided a problem of suitable size and future expandability while making use of a wide base of in-house expertise and experience. Another important benefit is the introduction of expert system technology to the site providing tools and experience for future system selection and technology application. CANMET has an on-going interest in assessing various aspects of ES technology (hardware, software, knowledge engineering, integration) while addressing problems in process operations that could most readily benefit from the technique. CANMET's role in the project was to provide project assistance, financial support, substitution algorithm assistance and software for data substitution. The knowledge bases (rules) have now been completed and are to be tested in the online environment."

Jan 1, 1989

By Scott Hean

"Environment and the economy are interwoven irrevocably. They need to be publicly discussed, and discussed often so that new approaches can be understood and developed - approaches which are complimentary, not confrontational.Discussion on the environment is timely, from the perspective of mining engineers and developers, from that of bankers and from their shared perspective as people concerned with enhancing the quality of life, the environment and the economy.This paper will touch on how what is called the ""environmental economy "" that has evolved has become entangled with regulatory and financial issues in a way that is dangerous for all of us. It will also look at some of the promising possibilities that a world-wide and continuing concern for the environment holds out for us.For many decades, British Columbia has provided some of the key examples of the intertwining of environmental and economic issues, and, very importantly, providing the people prepared to do something about them.Canada's first environment minister, the late Jack Davis, came from British Columbia. He led this country's delegation to the Stockholm Environment Conference in 1972, a conference that laid the groundwork of principles necessary to establish some international certainty as to the legal liability for causing trans-national environmental damage.Another British Columbian who was also a national environment minister, John Fraser - now the Speaker of the House of Commons - was one of the first to dramatize the importance of acid rain and force it into the international public arena.Some 20 years ago, British Columbians made Vancouver and their province one of the major centres of opposition to the Alaska Pipeline and Tanker System - with some justification, it now seems.That a British Columbian , then MP David Anderson, was given legal recognition to sue in a United States' court against a system that was either in U.S. territory or international waters was an important precedent in, and of, itself in terms of environmental law. That old controversy is now a very current case study - in terms of dealing with the question of liability.-"

Jan 1, 1991

By M. J. Medd, G. A. Speirs

"This paper describes the simultaneous sinking and equipping of a 4.9 m diameter concrete-lined shaft to a projected depth of 1660 m. The shaft blast design utilizes the full face method using a parallel hole burn cut. Hydraulic drilling and a totally redesigned Cryderman-type mucking unit were integrated into the four deck sinking stage to provide for drilling, mucking, concreting and shaft steel equipping operations. A safety program was tailored and implemented specifically for this shaft sinking project.IntroductionIn July 1988, Falconbridge Limited commenced development of its Thayer Lindsley exploration site located some four km north of Sudbury on Regional Road 80.The first phase of this project was awarded to J .S. Redpath Mining Consultants Limited and the scope of work included the engineering and project management to construct a surface plant capable of supporting a shaft sinking and exploration program for potential future mine development. This initial phase of the project was completed on schedule and under budget on December 23, 1988, and is the subject of an independent paper.In November 1988, J.S. Redpath Limited was awarded the shaft sinking and exploration phase of this project. The scope of work consisted of sinking and equipping a 4.9 m diameter shaft to a depth of 1660 m and carrying out the development and diamond drilling on two levels. This work was scheduled to be completed by November 1991.The T .L. Exploration Project is located toward the eastern end of the south range of the Sudbury basin, north of Sudbury. Figure 1 details the projected mining area and the shaft location on the geological complex. Figure 2 is a section showing the exploration shaft that is located in the Norite. Two levels will be developed from this shaft, on the 1310m and 1588 m levels, to provide access for further geological examination of the ore bodies."

Jan 1, 1991

By E. A. Davies, Trevor T. Jones

"Aspects of materials, design and operation of suspension equipment is dealt with, hazard, fatigue and special metallurgical properties of certain steels to resist are described, as is the effect of temperature in service modifying the properties of some steels to resist stress concentration and propagation of cracks.The influence of steady impact and fatigue loading and its results are described. Control of manufacture including nondestructive testing is outlined and acceptance parameters and strength calculations are given. Quality requirements and control in manufacture are outlined. A short description of the overwind detaching hook, together with illustrations of the operation of detachment are presented.MaterialsWinding engine ratings of 8000 h .p. and large capacity shafts 2000 m in depth (4000 m depths have already been reached and it may be necessary to go to 6000 m) and up to ten conveyances are not uncommon today. Loads of 100 or even 200 tons hoisted at low speeds are possible within the near future. Some of these appliances are designed to protect lives and installations in hazardous conditions when, due to human or mechanical fault, a malfunction occurs in the system. In addition, such equipment includes suspension gear of various kinds designed to anchor and apply high mechanical tensions to numerous steel ropes installed in shafts necessary either for the safe passage of conveyances or for balancing purposes when heavy loads are in motion.No unique metallurgical problems are presented in underground mining operations, but they have two special characteristics that influence the metallurgical aspects of the de sign of suspension gear and other equipment concerned in the transport of men and materials. (1) Any uncontrolled release of energy caused by the unexpected failure of a component is more likely to injure personnel and cause costly damage to installations in the narrow confines of an underground mine shaft. (2) Some mechanical equipment in mines, tends to be overloaded in service and suffer plastic distortion."

Jan 1, 1987

By L. Kilpinen, K. R. Kay, H. B. Fowler

"FOREWORDThe International Nickel Company of Canada has built four ore concentrating plants since 1950. The fifth and largest is now under construction. In each successive plant, the level and type of instrument control and sophistication of control techniques have increased as experience was gained. The type of control progress is illustrated in Fig. 1.At Frood-Stobie the high degree of instrumentation and the level of control were made possible by the constant evolution of techniques and improved instrument hardware technology. We have established in practice concepts that are sound, although many modifications to instrument sensor types and locations 1-rere often necessary. It is generally true that at other existing Inco mills, it is possible to run ""all manual"" for protracted lengths of time because of operator availability and dependence. The Frood-Stobie Mill is the exception, and it is the degree of reliability of the instrumentation hardware and level of maintenance that has made this possible."

Jan 1, 1971

By Roderick C. McDonald

Great Bear lake, the fourth largest body of water on this continent, comprises an area of approximately 12,000 square miles, and is set astride the Arctic circle, with a large portion of it witnessing both the Arctic winter night, and the Arctic summer day with its midnight sun. The very name itself, Great Bear, suggests an Arctic region. The seasonal contrasts at Great Bear lake are very marked by the cold and darkness of winter, and the warmth and brightness of summer. Signs of winter such as low clouds, snow, sleet, fog, and night frosts, generally appear the latter part of August, while ice forming on bays during the last two weeks in September ends boat travel on the lake about September 30th.Early in June the ice leaves the river mouths, during the last ten days of the month it disappears from small bays, and at some time during the last two weeks of July the main body of the lake becomes navigable. In 1916, the ice disappeared earlier than usual, and the lake was navigable on July 5th. Great Bear river generally breaks up about June 1st, but, on account of ice cliffs and floes, it is not navigable with safety until early in July. Even then, the traveller is confronted with the Charles rapids, but these might be overcome by a wagon or motor road, such as the one from Fitzgerald to Fort Smith: However, in 1931, Mr. A. W. Boland, Fort Norman, N.W.T., carried with scow and motorboat practically all freight between Fort Norman and LaBine point and Hunter bay, at the east end of the lake. During July and August, two types of clothing are required, for, although the days are mainly ones of warm sunshine, the nights are cloudy and cold. In the winter season, fur clothing is used exclusively. Considerable timber, mainly white spruce, suitable for fuel and building purposes, borders the lake and extends eastward to the Coppermine river. North of the lake, no timber is found except in the river valleys, but with oil and coal possibilities near Fort Norman, the fuel situation might be solved.

Jan 1, 1932

By J. W. Smith, J. Van Dusen, A. Papachristodoulou

"As part of a study to evaluate factors affecting tankroom air quality, the mechanism of aerosol generation from bursting bubbles in electrowinning operations has been investigated. Typically 2 to 3 mg/m2.s are produced in zinc tankrooms. Analysis shows that the rate of production of film drops (geometric mean diameter - 2 urn] increases with decreasing bubble size, and that jet droplets (geometric mean diameter - 20 um) are not produced with gas bubble larger than - 4 mm. Both mechanisms of drop formation and current efficiency are affected by surface active agents, with an over-all reduction in emission of up to 60% to 70% being achievable. A source control system which does not adversely affect electrolyte properties is always preferred, and coalescence of all gas bubbles in to a continuous stream of gas at a single point on the electrolyte surface would eliminate aerosol emissions. This objective was the basis for design of a coalescence device which, in laboratory tests, reduced the emission rate by over 95%.The control device fit s over the electrodes in the electrowinning cell and is partially immersed in the electrolyte. A number of changes in the design which resulted in significant improvement in the performance of the device are reported.Field tests have shown that only about 75% of the aerosol below 10 um can be eliminated by coalescence. The remainder (up to 95% of the total) is controlled by coalescence of droplets, by impaction on the exposed collector surface and gravitational settling.The device does not interfere with operation of the tankroom, handles the effect of surges in power during harvesting, and is simple and inexpensive to maintain. IntroductionDuring the electrowinning of metals (such as zinc and copper) gases are evolved along the electrode surface forming small bubbles. The bubbles travel upwards and burst on the electrolyte free surface generating, in this way, small droplets. Because the electrolyte is often highly acidic or contains toxic materials, the whole process can result in the formation of an aerosol in the atmosphere above the electrowinning cells which poses a serious health hazard to workers in the area, and corrodes equipment."

Jan 1, 1988

By F. Rojas, M. Sanchez, J. Palacios, O. Pavez

Copper sulfide is the main mining resources in Chile, and most of this metal is obtained via pyrometallurgical extraction in seven copper smelter plants, which extends from the northern Atacama desert to the central part of the country. In 2002, 1,522,000 metric tons of fine copper were produced, with a notorious environmental impact due to the large amount of slag generated, including transportation and disposing problems. Therefore, there is a great interest in finding alternative uses in order to give additional value to the slag. This is a total project development concept, which consider residues as new resources where new components could be obtained, improving sustainability in mining activities and also ensuring clean production processes. Thus, the present work shows a review of copper slag characterization as well as several ways of utilization, including compact material for road and railway installation, part of admixtures in concrete.

Jan 1, 2004

By P. Dyas, H. Zouitt, D. M. Smith

"Falconbridge Copper's Lac Shortt gold mine is located in northern Quebec approximately 300 km northeast of Val D'Or and 100 km west of Chibougamau (Pig. 1). Engineering for the mill commenced in early 1983 with a feasibility study. The plant was commissioned in the fall of 1984 at a capital cost of approximately $12 million. Design capacity was 750 tpd which was increased in the fall of 1985 to the current level of 1200 tpd.The ore at Lac Shortt is free milling, grading an average of 5.5 g/t gold which is finely disseminated throughout the host rock. Pyrite at 3 to 5% by volume and traces of copper mineralization are also present.Some of the latest gold processing techniques known at the time of design were incorporated into the mill. These include carbon-in-pulp, pressure stripping, electrowinning of pregnant solution and induction furnace refining. The plant also features several innovations such as a unique interstage carbon retention screen in the CIP circuit and the outdoor location of the cyanidation feed thickener, mill solution tank and reagent storage silos despite -40° Celsius winter temperatures.This paper describes the current mill process and discusses some of the problems encountered during the first two years of the plant's operation. CRUSHINGThe Lac Shortt surface crushing facilities are located in a separate building, isolated from the wet processing circuits for dust and noise control reasons. The crushing plant equipment was originally utilized at the Manibridge operation in northern Manitoba where it had been designed to operate at 135 tph. However, at Lac Shortt a rate of only 80 tph has been achievable to date, mainly due to the hardness and frequently slabby breakage characteristics of the ore. Therefore, in order to meet fine ore requirements at the current mill throughput of 1200 tpd, the crushing circuit is run seven days a week. 24 hours a day. Availability has been averaging 65%."

Jan 1, 1987

By Kenji Koga

In order to derive the population distribution of gold nanoparticle morphologies as a function of size, highresolution electron microscopic (HREM) observations and structural analyses were done for over 4000 particles (3-18 nm) grown by an inert gas aggregation (IGA) source using helium. To obtain structural features threedimensionally and not to skip high-contrast images, twenty photos were taken for each particle by changing tilting angle of a specimen holder in combination with the through-focus procedure. For the reliable structural determinations, HREM images and their tilting sequences were directly compared with multislice-simulation results for icosahedral, decahedral and face-centered cubic morphologies, and finally the population distribution of each morphology was obtained as a function of size. In the present sample, icosahedral particles were dominantly populated over the whole observed size range and decahedral particles with non-spherical truncated bi-pyramid shape were secondly dominant. Even though a large number of sampling has been done, few crystalline particles were observed.

Oct 1, 2003

By R. B. Taylor

"The Delnite mine is in the northwest part of Deloro township, Cochrane district. The property consists of 307 acres on the so-called 'South Break' in the Porcupine camp. The Company was formed in 1934 to take over the holdings of La Roche Mines, Limited. Gold has been produced continuously since June 1, 1937. The value of the gold recovered to date (December 31, 1946) has been $7,456,000, and the average grade of ore $6.81 a con.The ore at the Delnite occurs in relatively narrow, persistent, quartz-ankerite veins, which generally contain tourmaline and have a ladder-like structure. The gold occurs in the free state, and in association with pyrite and arsenopyrite, the two chief sulphides. The host rock is fine-grained, highly carbonatized andesite of Keewatin age."

Jan 1, 1954