Search Documents

By M. Dupuis, V. Bojarevics

It is well known that horizontal current density in the metal pad contributes greatly to the generation of MHD driven bath-metal interface wave. It is possible to compute very accurately the metal pad current density using a very detailed finite element model [1], but a MHD model must be compatible to this level of mesh refinement and to recalculate the current distribution at each time step, including the full busbar supply system. The accuracy of the instability prediction of the cell depends on the accuracy of the metal pad current density calculation. This study presents the comparison of the metal pad current density calculation of the detailed finite element model and the MHD-Valdis model for different metal pad heights and ledge thickness. It also presents the corresponding cell MHD stability predictions.

Jan 1, 2006

By R. A. L. Drew, C. A. Rodríguez González, Caleym W. F.

This work addresses the need of new refractories for copper converters. Technological improvements and environmental regulations for chromium containing refractories have generated this need. Chemical interactions, mechanism of penetration and the effect of oxygen potential and temperature in the system Cu2S-FeS-SiO2-O2 are presented for two refractories: a burned magnesite chrome brick (typically used by the copper industry) and a chrome-free spinel direct bonded brick. The main difference determined in the refractory performance was the blister copper penetration resistance; burned magnesite chrome brick is penetrated while direct bonded brick is not. These results are very promising since blister copper penetration has been reported as the major cause of refractory wear. The results are explained in terms of refractory porosity and wetting characteristics.

Jan 1, 2004

By S. Xu, A. Ramesh, F El-dabbagh, Z. Fang, A. Sobhy, J. A. Kozinski

Waste remediation is a goal that will be driven forward by economic conditions. As the cost of waste disposal increases, new methods of waste reduction will become economically attractive, and will be implemented. It is difficult to imagine, however, a time when there will be no waste generation. For the foreseeable future, despite effective reduction practices, there will still be hundreds of millions of tons of waste that must be destroyed or controlled to protect the public health and the sanctity of the environment. To remain faithful to environmental covenants, the mineral and metallurgical industries will face these new challenges. This paper discusses novel waste remediation approaches and techniques focusing on hazardous wastes and thermal remediation. Aspects concerning technological and environmental importance are examined. Solutions for neutralization of environmentally hazardous compounds are proposed.

Jan 1, 2004

By K. Barr, F. Grenier, J. Hettinger

"To reach the Hemlo Gold Inc. objective of becoming the lowest cost, safest Canadian gold producer while causing no environmental damage, management embarked from its inception on a strategy to build an organization which would foster employee involvement wherever possible. This paper describes the organizational structure and how various innovative concepts have been implemented.BACKGROUNDThe Golden Giant Mine in the Hemlo area of North Western Ontario is owned by Hemlo Gold Mines Inc. 50.1% is controlled by Noranda. The mine commenced operations in March 1985 at a modest production rate. After it reaches full production by the end of 1988, with completion of underground development work, the mine is expected to operate at 3000 t/d and produce in excess of 300,000 ounces of gold per annum. This makes it one of the three largest producing gold mines in North America.Two other companies, Lac Minerals and Teck-Corona, operate mines on either side of the Golden Giant Mine. Noranda Geco Division is located 55 kilometers to the north at Manitouwadge. The majority of Hemlo Gold's 270 employees live in Manitouwadge where a mix of accommodation was constructed and made available for purchase by employees. Bus transportation is provided to and from the workplace with modern coaches. The housing and transportation policies were implemented prior to start-up and designed to help attract and maintain good employees.As shown in Figure 1, the operation is divided into five operating and support departments with each reflecting a high degree of departmental control and responsibility. For example, the mill department is responsible for all aspects directly relating to the milling complex including safety, operation, mechanical maintenance, assaying, instrumentation, and environmental control. Similarly, the mine department is responsible for all phases of operation, mine engineering, geology, and maintenance of underground mobile equipment. The plant department is responsible for maintenance of hoisting plants and conveyances, underground stationary equipment, all site electrical services, surface buildings, housing and yard maintenance. Efforts are made at every level of the organization, from departmental organization to individual job assignments, to ensure responsibilities are clear and that they encompass complete functions."

Jan 1, 1988

By V. Bondarenko

The importance and necessity of gas hydrates deposits development followed by natural gas extraction is considered in the present paper. Analysis is given to world sources focused on methane hydrates formation conditions. Information covering the most perspective gas hydrate deposit of the Black Sea is presented in the article. Two most common methods of gas hydrates development ? thermo stimulation and inhibitor injection are analyzed presenting their comparative characteristics. Basic scientific trends and developments of underground mining department in the field of gas methane extraction from gas hydrates are scrutinized. Schemes and methods of natural gas hydrates development are shown together with formulas, parameters and factors influencing the extraction process. Also the analysis is given to the possibility of gas hydrates formation from methane-air mixtures of degassing wells from coal mines of Ukraine. Improved experimental unit for gas hydrates formation under laboratorial conditions is presented with its basic characteristics. General conclusions and basic tasks requiring further research are given in the end.

Aug 1, 2013

By T. G. Paradis, C. A. Mohns

"This paper summarizes the Wren CAT (Clarifier and Accelerated Thickener) deep bed thickener operation at the EKATITM Diamond Mine in Canada’s Northwest Territories. EKATITMs’ thickener project is presented in terms of initial design considerations and present day operating practices. A circuit description summarizes process equipment, reagent systems, and typical process conditions, and details of Wren CAT operating principles are provided. Operating strategies are discussed, with emphasis on process instrumentation and control and operating challenges.INTRODUCTIONThe EKATITM diamond mine, operated by BHP Diamonds, Inc., is located in the Northwest Territories near Lac De Gras, approximately 300 km NNE of Yellowknife, NT. 9000 dry metric tonnes of diamond-bearing kimberlite ore are processed daily. Processing operations commenced in October, 1998.The EKATITM process plant flowsheet features typical steps in diamond recovery plant design. Figure 1 shows the general plant flowsheet. Size reduction and feed preparation are accomplished by crushing, scrubbing, and high pressure grinding rolls (HPGR) through closed-circuit classification with vibratory screens. Heavy medium separation (HMS) is used as the initial stage of heavy mineral concentration. Secondary concentration is accomplished in the recovery plant by attrition milling; wet, high-intensity magnetic separation (both wet and dry); and X-ray sorting.The present budget throughput rate is 9000 dry tonnes per day. This will be increased to 18,000 tonnes during the first ten years of operation. Unlike most kimberlite treatment facilities, which process material from a single ore body, EKATITM’s process plant was designed to accommodate ore from five different kimberlite pipes, each with its own treatment characteristics.All processing, except for primary crushing, is carried out in a temperature-controlled environment in the main process plant building."

Jan 1, 2000

By W. Curlook

"A review is presented of a growing number of imperatives, some self-imposed, some imposed by society, which the mining and metals industry faces in carrying out its business. These imperatives bear on all activities from the exploration phase, through engineering, design, plant construction and operation, to decommissioning.IntroductionThe mining and metals industry must learn to cope with, i.e. manage, a growing number of imperatives. Some of these, such as the need for responsible stewardship of natural resources, the requirement to respect laws and regulations, the need to provide for safe and healthy workplaces, and the need to provide appropriate returns to investors of capital , have been with the industry for a long time (fable I). But the industry now faces additional imperatives that are growing in number and in importance (fable 2):• There is the growing concern about the impact of operations, not only on the workplace environment and the external environment, but also on the need to monitor not only the chemical concentrations in various effluents but to also monitor the effects of such emissions on the environment; i.e. there is a growing concern about the ""net"" consequences of operations.• There is the need for on-going improvement in productivity and safety to compete and survive in a global economy. The global business environment has become paramount.• There is the imperative to failsafe all designs, equipment and operational procedures, and having done that to provide for containment of unavoidable spills, and to have ready and in place systems for emergency response.• There is the need, indeed the imperative, to involve all employees in various quality improvement programs.• There is the imperative to face up to ""virtual elimination/zero emissions""; and• One must have waste management plans in place to cope with the need to reduce, reuse, and recycle; and• There is the need for decommissioning plans for all operations, for the restoration of business habitats to their original states (or better). Indeed, one must engage in the decommissioning exercise from day one, i.e. right from the time of design and commissioning."

Jan 1, 1992

By N. W. Xu, C. Sha, F. Dai, Y. G. Zhu, B. Li

Underground caverns stability and excavatability of rock masses are of significance in geotechnical engineering, in both design and construction stages. Risks associated with underground group caverns of Houziyan hydropower station in southwestern China are growing as a result of continuous excavation-induced unloading. To improve our understanding of the underground caverns instability and resolve the complex subsurface conditions of the highly fractured rock mass, a high resolution microseismic monitoring system was established in the deep underground caverns, pursuing the relationship between the measured data about microseismic activity and excavation damage zones of surrounding rock mass. Through analyzing the tempo-spatial distribution of microseismic activity, excavation damage zones and potential risk regions in underground caverns were identified. Furthermore, the correlation between microseismic activity and pre-existing geological structures, as well as traditional monitoring was analyzed. In order to validate the correlation between seismicity and potential slip surface of underground caverns, a model was implemented into numerical code to further evaluate the deformation and stability of surrounding rock mass. The monitoring results demonstrate that microseismic events mainly occur at high stress concentration regions, which coincides with the results obtained from numerical analysis. Therefore, the comprehensive method incorporating microseismic monitoring and numerical analysis, as well as traditional monitoring and filed observation has been proven to be very promising in deformation and even instability prediction of surrounding rock mass in underground caverns subject to delineation of potential slip surfaces and excavation damage zones.

Jan 1, 2015

By S. Stefanizzi

In the present paper, numerical simulations based on a finite/discrete element approach are used to study deformation and failure process during standard rock mechanics. FEM/DEM modeling has been used as available with the ELFEN code, which explicitly model the transition from continuum to discontinuum. The transition is simulated through a crack nucleation and propagation that obeys to the Griffith?s failure criterion. If the fracture criterion within the intact rock (represented by FEM) is met, a new crack (represented by DEM) is initiated. Remeshing allows the fracture process through the FEM mesh to be tracked and visualized, thus contact properties can be assigned to pre-existing fractures and newly generated fractures. In this study, compressive tests of rock samples are simulated. The applicability of ELFEN to properly and efficiently simulate typical laboratory rock mechanics tests, with reference to the rock fracture process, is described in detail. In addition, an indirect validation of the extensional strain criterion proposed by Stacey (1981) is given.

May 1, 2009

By O. Rabeau, M. Legault, A. Cheilletz, L. Z. Cheng, J. J. Royer, M. Jébrak

"By compiling geological, structural, geophysical, and geochemical information into a 3D geological model, we evaluated the orogenic gold potential in the vicinity of a hidden segment of an important Archean fault zone, the Cadillac-Larder Lake fault (CLLF) in the region of Rouyn-Noranda. The segment of CLLF in the present study is partly covered by Proterozoic sedimentary rocks. Because more than 2000 t Au have been extracted along the CLLF to date, our objective is to evaluate the gold potential at depth along a poorly known segment of this fault. A 3D geological model (50 km × 9 km × 1.5 km) including the covered segment was built through the compilation and homogenization of available geological data and the construction of 23 cross sections. The geology under the Proterozoic cover was evaluated using geophysical inversions, drill holes (42 in total), and surrounding geology. All available assays were filtered and upscaled to a 250 m × 250 m × 250 m regular cell grid to determine and quantify spatial relationships between geological features and mineralized occurrences using the weights of evidence method. Structural features, such as E-W-trending faults and fault intersections, and certain lithologies with a high primary porosity such as volcanoclastic rocks of the Blake River Group and Timiskaming sedimentary rocks, proved to be very prospective, yielding favourable factors with a weight of evidence index W+ > 0.24. These salient features were then assigned a combination index for ultimately evaluating the orogenic gold potential under the sedimentary cover. The zones resulting in an optimization of exploration targeting were attributed the highest probability, representing ~1% of the initial volume. La compilation des données géologiques, géophysiques, structurales, et géochimiques et leur intégration au sein d’un modèle géologique 3D a permis d’évaluer le potentiel aurifère dans les environs d’une importante zone de faille archéenne sous couverture protérozoïque. Cette méthodologie a été développée en utilisant le cas de la Faille Cadillac-Larder Lake (FCLL) dans la région de Rouyn-Noranda. Puisque plus de 2000 t d’Or ont été extrait à proximité de la FCLL, l’objectifs des travaux est l’évaluation du potentiel aurifère en profondeur de ce segment. Un modèle géologique 3D (50 km × 9 km × 1.5 km) incluant le segment sous couverture de la FCLL a été construit en utilisant l’ensemble des données géologiques disponibles et 23 coupes géologiques. La géologie du socle archéen sous la couverture protérozoïque a été interprétée avec des inversions géophysiques, des forages (42 au total) et les contacts géologiques exposés. Les teneurs aurifères dans le secteur ont été filtrées et ajusté à une grille régulière de 250 m × 250 m × 250 m afin d’évaluer et de quantifier les relations spatiales existantes entre certaines entités géologiques et les emplacements minéralisés en utilisant la méthode du poids de la preuve. Les failles de direction Est-Ouest, les intersections de failles ainsi que certaines lithologies possédant une porosité primaire importantes comme les certains tuf du Groupe de Blake River et les sédiments du Timiskaming se sont montrés très prospectifs avec des valeurs de W+ > 0.24. Ces entités géologiques ont ensuite été utilisées par le biais d’un indice de combinaison pour évaluer le potentiel en or de type orogénique sous le couvert sédimentaire. Cette méthodologie permet une optimisation des campagnes d’exploration puisque les zones pour lesquelles la probabilité de minéralisations a été évaluée à la plus haute valeur représentent 1% du volume initial."

Jan 1, 2009

By F. M. Waldie

THE 2,538-foot belt conveyor recently installed underground at the Sullivan mine hoists ore from the 3,350-foot level to the 3,900-foot or main haulage level, a vertical distance of 680 feet. The design and planning of development work, under the direction of Mr. R. H. Stewart, Consulting Engineer, was begun in the spring of 1941. Development work was started in July of that year from the 3,350-foot level, and headings were started on the 3,650-foot and 3,900-foot levels later in the same year. It was the intention at that time to keep three headings going on development work necessary for the installation of the system: two on the conveyor incline, and one on the 3,900-foot level. This programme was modified in 1942 when there was some doubt whether the material for construction could be obtained. This problem of supply was eventually solved and the development work was pushed to completion in December, 1943. Construction was started in December, 1943, "'under the supervision of Mr. G. H. McKay, Superintendent of Construction and? Maintenance, and was completed in November, 1944.

Jan 1, 1945

By C. -G. Berg, J. T. Tuominen

Since the beginning of the 20th century, energy efficiency in copper smelting has been improved by a factor of 30 as a result of adopting autogenous smelting processes with more and more efficient waste heat recovery systems, increasing use of oxygen enrichment and countless smaller improvements. Nevertheless, energy in the form of electricity and fuels continues to be the biggest contributor to smelter operating cost. Metallurgists around the world are under constant pressure to find ways to save those precious megajoules wherever they can. One area that is often neglected is the removal of water contained in concentrates. Copper flotation concentrates, as delivered to a smelter, typically contain some 8–12% moisture. This moisture must be removed and the only way to do this is by evaporation, which consumes a lot of energy. Several studies have shown that the most efficient way of removing this moisture is to use a steam- heated indirect dryer—the least efficient way being the feeding of wet concentrate directly into a smelting furnace. Even in the most efficient smelters that employ modern steam drying, the energy needed to remove the moisture from the concentrates constitutes over 15% of the total energy consumption of a smelter – acid plant complex. The major steps that have been taken in the past to lower the energy consumption of moisture removal are the use of drying in general and the adoption of steam drying. The energy efficiency of concentrate drying has been improved by 25% over the last 20 years. The latest giant leap in this area, the Kumera Heat Recovery Dryer, is the result of Kumera’s long-term development in improving the efficiency of concentrate drying. The Heat Recovery Dryer is a novel application of steam drying that uses the waste heat from dryer exhaust gas for drying concentrates, thus, cutting the energy consumption by a further 30%. This paper discusses energy consumption in copper smelting in general and analyzes the energy consumption of concentrate drying in detail. Different dryer types are compared especially from the perspectives of energy consumption and environmental emissions. Applicability of different energy sources for drying is evaluated and discussed. The principle of the Kumera Heat Recovery Dryer is presented along with results from extensive continuous pilot plant tests. Potential applications and the feasibility of Kumera Heat Recovery Drying technology are discussed.

Jan 1, 2019

By Jason Rrno

The emergence of Impact and Benefit Agreements (IBAs) in the Canadian mining sector has been read by many as a positive governance innovation. Negotiated directly between mineral resource developers and Aboriginal communities with limited government interference, IBAs serve to manage impacts associated with a mining project and deliver tangible benefits to local communities. Notwithstanding their increasing use and significance, limited systematic analysis has been undertaken to determine whether they are, in fact, working. This paper reports on the effectiveness of a number of IBAs negotiated in support of three northern Canadian diamond mines, drawing on evidence from time-series data, key informant interviews, and focus group meetings in Yellowknife and Dettah, NWT, and Kugluktuk, NU. While some deficiencies were apparent and perceptions of effectiveness varied somewhat by Aboriginal community, the IBAs were generally found to be meeting their objectives, especially with respect to the delivery of benefits. For Aboriginal communities affected by mineral development in the Canadian North, this represents a significant change to typical outcomes of the past. Moving forward, research on IBA effectiveness needs to adopt a longer timeframe and begin to gauge the degree to which IBAs are able to address long-standing concerns associated with hinterland resource extraction beyond their agreement-specific objectives.

May 1, 2010

By Richard Klimpel

"Over the last 15 years, there has been a number of plant scale sulfide mineral flotation tests organized by this author specifically aimed at understanding how flotation rate varies with reagent type and dosage. With regard to the Interaction of collector dosage, particle size, and frother type, the eight specific trends listed in the paper (Illustrated with data from two specific case studies) are qualitatively the same for almost all plants studied in some depth. The Interaction of flotation rate K and equilibrium (Infinite time) recovery R in the plant has been denoted as the R/K trade-off. The effect of collector dosage on the rate of flotation of specific particle size intervals is particularly interesting and once understood, is quite useful In understanding how industrial flotation plants respond to changing reagent type and dosage. The location and magnitude of the R/K trade-off can be different for various ores and various plant configurations, but the RIK trade-off is almost always present. The purpose of this paper is to clearly describe and illustrate the nature of this very Important flotation system Interaction so that operating engineers have a starting reference point for beginning successful plant Improvement studiesIntroductionIt is well recognized by industrial froth flotation plant operators that improving existing sulfide circuit performance is often difficult due to the self-compensating systems nature of the froth flotation system, e.g. Klimpel (1988, 1989, 1995). Extensive plant testing with existing and new reagents by this author throughout the world has clearly shown that one of the more important self-compensating mechanisms is the Interaction between collector dosage, frother type, and particle size. The term self-compensation in flotation simply means that as the plant operator consistently changes one parameter in the same direction, the nature of the froth flotation system Is such that the circuit will eventually begin to resist this controlled parameter change by automatic (uncontrolled) changes In other parameters and the overall circuit performance will go through a maximum or minimum (hence causing the operator to stop the parameter change)."

Jan 1, 1997

By L. W. Vigrass

Porous and permeable rocks deeply buried in sedimentary basins contain immense volumes of hot water with the potential to supply low-grade heat energy. A part of Canada with sizeable potential for low-grade geothermal energy is the northern Williston Basin of southern Saskatchewan. In this region, the University of Regina has conducted a geological study investigating the feasibility of producing large quantities of warm water suitable for space heating in the Regina - Moose Jaw area. The study has shown that the most favourable geothermal reservoirs are in the Basal Clastic Unit (Cambrian Ordovician), which, at an approximate depth of 2,000 metres has predicted temperatures of 71°C to 74°C. We anticipate sustainable flow rates from these reservoirs of 100 to 300 ms/hr. The water contains about 150,000ppm of total dissolved solids, mostly sodium chloride. It is anticipated that the sulphate content will be 3,000 to 6,000 ppm, that the dissolved oxygen and hydrogen sulphide content will be small, and that the waters will be neutral to slightly alkaline. It is anticipated that the piezometric level will be 46 m below the ground surface for reservoirs in the upper part of the Basal Clastic Unit and 141m below the ground surface for the lower reservoirs of the unit. Plans are to build a low-grade geothermal research, testing and demonstration facility at the University of Regina. To be a practical demonstration, the facility will have to handle very large volumes of water. Because of high salinity, the water will be re injected into a subsurface reservoir. We do not anticipate insurmountable problems because of salinities or as a result of corrosion provided that the waters are not aerated during handling

Jan 1, 1979

By J. D. Bliss, G. J. Orris, W. O. Menzie

"Analysis of gold placer data from gold placers throughout the world suggests that gold grades and volumes cannot be used to distinguish between most types of gold placers. Only the alluvial plain and fan placers are significantly different among the types of gold placers considered. Gold grades and volumes change when working gold placers go from small-volume methods to large-volume methods. The small-volume methods are either of the surface or subsurface (drift mining) type. The odds that a gold placer will be dominantly worked using small volume methods at the surface are about 5:3. Once small volume mining has occurred, the odds against subsequent large-volume mining are about 4:1. If a placer deposit is suitable for large-volume mining, and the amount of gold produced from small-volume mining was reported, an estimate of the remaining gold (log10kg) can be made using the following equation:The relationship shown by this equation suggests that very large gold placers have over half their total gold content in the rich gravels appropriate for small-volume mining. These relationships in conjunction with other data and computer simulation can be used to estimate placer gold resources for an area targeted for mineral resource assessment. IntroductionGold placers have been an important source of gold throughout man's history and may have been one of the first sources-dating back to around 6000 B.C. (Gregory, 1980). From the primitive basket to the modern floating dredge, a variety of methods have been used to work gold placers. Placers are found in a wide spectrum of geologic and climatic settings. They have been classified by using a mixed set of criteria including age (Recent, Tertiary), climate (desert), fluvial position (modern channel, bench, alluvial fan), environment of deposition (eluvial, alluvial, residual, beach), type of transport (stream, wind, glacier), and whether the placer is buried or at the surface (Boyle, 1979; Wells, 1969). Several mining methods have usually been used to extract gold from anyone placer."

Jan 1, 1987

By J. G. Price

"The paper reviews state-of-the art welding processes and consumables for structural and pressure equipment applications in offshore environments, particularly the Arctic. Optimum selection of consumables will be discussed with regard to the facility to meet tentative toughness requirements in weldments. Finally, the development of welding procedure specifications will be considered in relation to the prevention of hot or cold cracking and lamellar tearing.Welding RequirementsGeneralThe exploitation of Canadian frontier oil and gas reserves will require a fleet of various types of offshore structures. These will include fixed jacket types and semi-submersibles for the East Coast with huge man-made islands and icebreakers for the Arctic regions. Both these regions will also require supply and drill ships plus subsea pipelines and cargo tankers for transportation. Clearly the welding of these items will plays large part in the over-all integrity and safety of exploration and production operations.The required development in structural steels and pressure vessel steels, for current and future offshore structures, to improve properties, particularly toughness for lower temperature service, has also prompted welding researchers to develop process and consumable combinations to match the parent plate specifications. This development has had to consider particular aspects of weldability such as a low susceptibility to cold cracking and preventing low HAZ toughness. Current research has centred on attempts to increase HAZ toughness with higher heat input welding of newly developed structural steels.The installation of Arctic region pipelines has provided a sound base for future, more complex fabrications in the most severe service temperatures in the Canadian frontier although few of the installations have been designed to the lowest possible exposed temperature of -62°C."

Jan 1, 1987

The North Saskatchewan River flows southwest to northeast through a 22-km-long valley in the City of Edmonton, supplying the drinking water to dozens of downstream communities. During heavy rains, combined sewers occasionally overflow into the river, which has a significant negative impact on the water quality and the sensitive environment. The West Edmonton Sanitary Sewer (WESS) W12, a syphon connecting the Rat Creek Trunk to the Gold Bar Wastewater Treatment Plant across the river, was designed and constructed to take the overflow to the wastewater treatment plant. Due to the complexity of the project, various 3D technologies were applied to facilitate decision-making processes. 3D models were developed for design review and design conflict detection, while 4D models were established to help create a robust construction schedule. Construction sequencing animation was used to convey design intents and demonstrate construction stages to contractors and workers. The combined applications of 3D technologies helped the project team to identify critical issues, and assured effective communication among engineers, management, contractors, and other parties. Therefore, it provided more opportunities for the success of the project.

Aug 1, 2013

By P. P. Andrieux

The recovery of the Zone G crown pillar, located between the bottom of the open pit and the top of the underground workings at the Raglan Katinniq Mine in Nunavik, started in the summer of 2008 and should be completed by the end of 2009. This article describes the rock mechanics-based approach implemented to design the recovery of this valuable block of ore. The stereophotography-based ShapeMetriX3D technique was first used to provide a comprehensive assessment of the various joint sets that comprised the pillar. Then, the statistical distributions obtained for the dip, dip direction, spacing and persistence of these sets were used in conjunction with the geometry of the large-scale faults present in the area to build and run a series of explicit rigid numerical models. Each of these models had a slightly different jointing geometry, randomly constructed from these statistical distributions. Incorporating in a properly formulated numerical model the variability of some of the input parameters has allowed the engineering team to assess in a rational and reliable manner the likelihood of success of the proposed mining method and sequence.

May 1, 2009

By Marie-Eve Boucher

The slag in iron ore pellets allows wet sintering during firing and leads to suitable bounding. The process of slag formation differs whether it takes place in the core or in the external zone of a pellet. In the core, hematite can be reduced to secondary hematite, depending on the temperature and on the carbon monoxide/dioxide partial pressure ratio. The reaction rim that appears at the outskirts of a silica particle in contact with the FeO bearing magnetite is considered as the slag precursor in the core of the pellet. By contrast, in the external zone of a pellet, where O2 is available and CO partial pressure is very low, the first step towards slag formation is flux decomposition, mainly dolomite and limestone. The CaO liberated through this reaction will be available to react with hematite by solid diffusion to form calcioferrites, which play an active part in the slag evolution process. These two slag formation paths will be explained.

May 1, 2007