Search Documents

By I. Imris

The chemical industries are using different type of catalysts, which after application usually produced many tons heap of residues. One of them is cupric oxide catalyst with high content of copper and silica. The recovery of copper from the waste has become major interest from a viewpoint of environmental protection and recycling of resources. The thermodynamic analysis and experimental results suggest that the copper from cupric oxide catalyst can be extracted by plasma reduction process. By plasma reduction process the inert slag and copper with following chemical composition: 99.04 % Cu, 0,042 % Fe could be obtained.

Jan 1, 2007

By A. Eslami, H. Tabatabaei, M. Kolandoozan, Z. Manafi, A. R. Shahverdi, M. Noaparast, M. Oliazadeh

Application of Acidithiobacillus ferrooxidans bacteria to flotation of Sarcheshmeh low-grade copper sulphide ore was studied. Sarcheshmeh low-grade ore contains pyrite, which causes some problems in the flotation of copper minerals. In this study, A. ferrooxidans was used to change the surface chemistry of pyrite and copper sulphide ores and consequently, their flotation behaviour. In the presence of A. ferrooxidans and xanthate as a collector, pyrite was depressed whereas chalcopyrite and other sulphide minerals were unaffected. In addition, the pulp pH remained unchanged. It was shown that the surface chemical properties of the bacteria can be manipulated successfully to achieve the desired effects in a flotation process. The results showed that the recovery of pyrite in the presence of the bio-depressant is 50% lower than when no bacteria were present. At the same time the recovery of chalcopyrite remained unchanged.

Jan 1, 2004

By Pizhi Zhao, Jingwei Zhao, Zhenshan Liu, Yiheng Cao

"A new Al-Mg-Si-Zn alloy designed for automotive outer panel was trial-produced with industrial procedure. The final product shows a strong planar anisotropy. X ray diffraction analysis shows such strong anisotropy is caused by the dominating cube texture component in the final product. The reason for such high cube texture component was investigated by tracing texture evolution starting from the hot roll slab. It is found that certain cube texture components already exists in the hot rolled slab. The density of cube texture component shows as a wavy change through the following1st cold rolling, inter-annealing, 2ndcold rolling and solution treatment. This study shows that the cold rolling in the laboratory can well represent the texture evolution during the industrial production. The results obtained by lab rolling hints that change of second cold rolling reduction has weak effect on the planar anisotropy, when the gauge of hot rolled slab and final sheet are fixed.INTRODUCTIONWith the rapid progress of light-weighting in the automotive industry, aluminum sheets get more and more application as closure panel and structure parts. Recently the dominating alloy for outer panel is 6xxx series, containing the main alloy elements Mg and Si. The popular gradesareAA6016,AA6111, AA6022, and AA6014. These alloys still cannot satisfy the various requirements from automotive manufacturers. Most suppliers of automotive aluminum sheets are developing their own specific grades according to the customer’s demand. To increase the baking response, anew Al-Mg-Si-Zn alloy was designed, concerning the high combination energy between Zn solutes and vacancies formed during the quenching stage of automotive sheet manufacture. This combination is helpful to the precipitation of ß”phase during the paint baking (Wang, 2015,2016; Yan, 2014).The plastic strain ratio (r value)is a key index of the formability of automotive body sheet. A high r value means a good formability. The r values in different directions can be used to evaluate the planar anisotropy of the metal sheets. The trial produced Al-Mg-Si-Zn sheet shows a strong planar anisotropy with respect to r values. Since the r value is tightly related with texture, the texture evolution from hot roll slab (HRS) to final T4P temper was analyzed with X ray diffraction (XRD) to find the reason for the high anisotropy. Besides, the cold rolling reduction (CRR) was varied in the laboratory to modify the texture distribution, i.e., the planar anisotropy."

Jan 1, 2018

By Dong-Hyeun Koh, Yun-Soo Lee, Min-Seok Kim, Hyoung-Wook Kim

High strength AA7068 (Al - 7.88 wt.% Zn - 2.68 wt.% Mg - 2.07 wt.% Cu) aluminum alloy strip was successfully fabricated by horizontal-type twin roll casting. A simulation technique was used to obtain the range of casting conditions for fabricating strip without defects. The cast strip with thickness of about 5 mm was hot rolled, intermediate annealed, cold rolled to final thickness and subsequently annealed at various temperatures. Tensile properties of annealed and the aged specimens were evaluated at ambient temperature. Tensile strength and elongation of the annealed sheet are about 365 MPa and 28%, respectively. Also, the tensile and yield strength after the aging at paint baking condition (180 °C x 0.5 h) are 586 MPa and 551 MPa, respectively. Therefore, it is expected to show good formability prior to press or stamping and also provide high dent resistance after paint baking treatment.

Jan 1, 2015

By Michael Moser, Brighty Dutta, David Dreisinger

"Molybdenum is widely used in the industries as an alloying element in the manufacture of steels and super alloys. The widespread use of the element encourages a growing need to develop extraction processes for recovery from both primary and secondary sources. The Solvay Group has developed a solvent extraction reagent named CYANEX®600 for the recovery of molybdenum from acidic solutions originating from both low grade (e.g. copper solvent extraction raffinates, smelter dusts and slags) and high grade (molybdenite) molybdenum sources. CYANEX®600 is a purified form of CYANEX®272 with the active component bis(2,4,4- trimethylpentyl)phosphinic acid. The extraction behavior of CYANEX®600 towards molybdenum in sulphuric acid medium was evaluated. The uptake of molybdenum increased with the increase in concentration of CYANEX®600. The approximate stoichiometry of the extracted complex was: Mo: CYANEX®600 = 1:2. Efficient back-extraction could be achieved with 0.1 M disodium EDTA and 0.1 M (NH4)2CO3, thus providing the option of recyclability of the extractant. The detailed back-extraction studies are currently under progress to find out the possible option for complete transfer of Mo(VI) to the aqueous phase so that high purity Mo salts could be precipitated from the molybdate solutions.INTRODUCTION Molybdenum (Mo) is one of the world’s valuable metals and is highly sought after by researchers due to its versatile mechanical, thermal, chemical properties. Swedish scientist Carl Wilhelm Scheele demonstrated molybdenite to be a mineral sulfide in 1778. Peter Hjelm successfully isolated dark metal powder from the mineral sulphide and named it as ‘Molybdenum’ in 1782 (Gupta, 1992). Molybdenum is a refractory metal of silver gray appearance and is an important alloying element used in the manufacture of steels and super alloys. Molybdenum compounds are widely used in formulation of catalysts (Gupta, 1992). Molybdenum occurs in nature only in chemical combination with other elements. Several molybdenum bearing minerals have been identified, but the only one of commercial significance is molybdenite (MoS2). As molybdenum is a strategic metal for the industrial sector, its widespread use acts as a factor for depletion of the natural resources. Hence, there is growing need to develop extraction procedures for its recovery from both primary and secondary sources. United States, China, Chile, Canada, Peru, and Mexico are listed as the main producers by the U.S. Geological Survey, 2016 (U.S. Geological Survey, Mineral Commodity Summaries, January 2016)."

Jan 1, 2017

By W. E. Bawden

Situation: Creighton mine, situated about twelve miles west of Sudbury, Ont., on the Algoma Eastern railway, is owned and operated by the International Nickel Company, incorporated in the United States under the laws of New Jersey. The ore is smelted at Copper Cliff, near Sudbury, and the matte is refined at Port Colborne, Ont., on lake Erie. Geology: The ore occurs in what is known locally as 'the basin' near Sudbury (Figure 1) the central part of which is composed of the Animikie series of sediments, consisting of sandstones, slates, tuffs and conglomerates. The basin is about 16 miles wide and 36 miles long. The Animikie sediments are surrounded by a sill of norite - a gabbro rock in which the pyroxenes are orthorombic. On the outer contact of this norite the sulphide deposits occur and the Creighton deposit, similar to others, lies on the southern edge of this basin. There are two orebodies at the Creighton, the upper one called the footwall orebôdy, and the lower one the hanging-wall orebody. The hanging-wall of both of these bodies is norite, and the footwall of the upper one is granite. The two are separated by an intrusion of greenstone which forms the footwall of the lower body. The ? maximum length of the deposit is 1000 feet and the maximum width is approximately 300 feet. It narrows at the ends and is somewhat lenticular in shape. The dip is about 45 o to the west, and the strike is north and south. The orè is a mixture of three minerals - pyrrhotite, chalcopyrite and pentlandite. The pentlandite, which is distinguished by its cleavage from the other two, is apparent to the naked eye only in the lower orebody and is more finely disseminated in the upper one. The lower body contains a little higher percentage of nickel.

Jan 1, 1925

By Song (Bruce) Li

This paper presents a three-tier web-based GIS application that uses Java Server Page (JSP), Java Servlet and relational database to manage performance monitoring and reporting in the oil sands mining industry. It is a real-time Earth Structure Performance Monitoring System (ESPMS), which allows the user to record and store instrumentation monitoring readings as well as technical observations and instrumentation installation documentations into a complete relational database. The ESPMS introduces the advantages of precise field record keeping, due diligence, security, consistency and completeness while at the same time simplifying the task of reporting. ESPMS combines web-based Geographic Information System (GIS) mapping and data management to facilitate the collection, organization, retrieval, reporting and communication of the vast amounts of monitoring data related to mining and tailings engineering associated with site investigation and construction information. ESPMS utilizes web-based GIS technology to incorporate referenced aerial photographs, Energy, Mines and Resources (EMR) maps or AutoCAD drawings as a base map for the monitoring site. It dynamically creates and administers all instrumentation monitoring locations and reading frequencies. It enables the user to collect and manage the data associated with an unlimited number of reading events. It provides the designer with real-time monitoring data (what, why, when, how), thereby allowing them to make early adjustments to design protocols or procedures, or to take remedial action(s) regarding the subject earth structure under construction or after completion. It provides more cost-effective reporting and data sharing through the Internet. It improves security on data entry and eliminates unauthorized data changes. It allows better integration of graphics and illustrations with numerical data files. It is capable of managing the continually expanding workload resulting from new and larger structures in the oil sands or other mineral mining industries. The ESPMS facilitates easier data gathering for preparation of as-built and after-built or regulatory reports, etc. It enables quick location of the interested instruments and summarization of the performance of the instruments. It enables one to visualize performance data and QA/QC construction test results spatially on any given cross-section. Data can be exported to MS Excel for detailed analysis and to evaluate the stability of the earth structures.

May 1, 2004

By J. Satur

In copper mineral processing, pyrite coexisting with copper sulfide minerals like chalcopyrite is separated by flotation as tailings and its oxidation in tailing dams causes the formation of acid mine drainage. This paper proposes carriermicroencapsulation (CME) as a new method for suppressing pyrite flotability, as well as its oxidation. In this method, an organic carrier combined with Ti is used to form a thin Ti02 layer on pyrite, which gives a hydrophilic property and acts as a protective coating against oxidation. To form the coating, a ground pyrite sample was treated with Ti-catechol complex solution under various conditions. Bubble pick-up experiments and flotation experiments showed that the treatment of pyrite with Ticatechol complex changed the hydrophobic nature of pyrite into hydrophilic even in the presence of xanthate as a flotation collector. Oxidation testing of the CME-treated pyrite by 0.02 kmol m-3 HN03 showed that Fe release was suppressed by the CME treatment with respect to the control. This is assumed to be due to the formation of Ti02 coating on the pyrite surface. The effect of CME treatment on chalcopyrite wettability is also discussed.

Jan 1, 2007

By M. Seyed Ahmadi

This study investigates the role of nitrogen gas injection in the dissolution rate of Si into liquid Al. A unique revolving liquid metal tank was used, with a capacity of 50 kg of liquid Al. Experiments without gas injection have shown that the dissolution of Si increases as the bath superheat and the tangential velocity of the liquid Al increase. When injecting nitrogen gas at flow rates between 0-5 lit/min in the vicinity of the solid Si, results so far clearly show greater dissolution. In addition, results on the role of the gas flow rate relative to the position of the nozzle are presented and analyzed.

Jan 1, 2011

By A. Bowles

The process of accumulative roll bonding (ARB) has been applied to wrought magnesium alloy AZ31. Accumulative roll bonding results in severe plastic deformation of sheet material. In AZ31, this process leads to the refinement of the microstructure by dynamic recrystallization. The refinement of the microstructure results in an improvement in mechanical properties with potential for producing materials for superplastic forming. In this work AZ31 was bonded with up to 64 layers and the potential of roll cladding with aluminium was also investigated. The development of microstructure and the mechanical properties are reported here.

Jan 1, 2006

By H Zorychta

Based on underground measurements made at the Nova Scotia coal mines of the Dominion Coal Company, Limited, this paper presents a comparison between the physical properties of hardwood packs and steel friction props when used for longwall support. The probable loads sup-ported by steel friction props on a longwall face at both the Dominion No. 20 Colliery and the Princess Colliery are delineated, and the results of the tests are presented in graphical form. It is concluded that the steel friction props are more efficient than the hardwood packs that they replaced as roof supports. Introduction AN evolution in the methods of longwall face support is taking place in the Sydney coalfield. Longwall face support had consisted primarily of timber props and hardwood packs. In 1957, however, at the Princess Colliery, Sydney Mines, Nova Scotia, the first longwall was equipped with steel friction props. At the present time, eleven longwall faces are supported on wood and sixteen faces are carried on steel friction props.

Jan 1, 1965

By S. Kashani-Nejad

The kinetics of the thermal decomposition of samples of Mg2(OH)3Cl.2H2O that were obtained by a novel leaching technique applied to a commercial magnesium electrolysis feed were investigated under ambient atmosphere. Thermogravimetric (TG) Analysis showed that decomposition of Mg2(OH)3Cl.2H2O exhibited a single intermediate stage wherein crystalline water was lost at roughly 108 °C. Conversion of the resulting Mg2(OH)3Cl to MgO, HCl and 1120 occurred at temperatures above 398 °C. Thermal decomposition of anhydrous Mg2(OH)3Cl was seen to be consist of two stages. Both stages exhibit first order kinetics with respect to the weight percent of Mg2(OH)3Cl remaining in the sample. However, the rates of decomposition in the two stages were significantly different. Detailed analysis of the kinetic data suggested that the rate of decomposition of Mg2(OH)3C1 was controlled by the rate of removal of the gases released. The change in decomposition rate during the course of the experiments was explained by HCI being released in stage 1 and followed by release of H2O in stage 2.

Jan 1, 2004

By G. Ergin

The interactions taking place between Al-Mg alloys and the bed media during aluminum filtration are not yet well understood. These interactions were studied using the infiltration technique. The reaction interface was analyzed using different techniques such as SEM and TEM. Only spinel formation was observed at the interface regardless of the type of alumina and contact time. This paper discusses the results of the study.

Jan 1, 2004

By D. B. Dreisinger, M. R. Tavakoli

Vanadium has been produced from both primary and secondary sources having various compositions. Vanadium pentoxide and vanadium trioxide are the most available and known sources of vanadium oxides. In this paper, an overview of leaching both oxides has been reported. The problem of vanadium pentoxide leaching under acid conditions is the low solubility of the dissolved vanadium. This was investigated and then supplemented with further studies of leaching at mildly basic pH’s as well as under acid reductive leaching conditions (to form vanadium (IV)). Atmospheric oxidative leaching of vanadium trioxide was investigated using oxygen and ferric ion as the oxidant. It was shown that the leaching of vanadium trioxide using oxygen is very slow; however, ferric ion can dramatically increase the kinetics and leach efficiency.

Jan 1, 2014

By Claude Bazin, Jalna Lamontagne

"The operators of mineral processing plants collect daily samples from strategic process streams with a view to prepare production balances to assess plant performances. The rules to minimize the risk of systematic sampling errors are known and applied in many mineral processing plants. The mass of the sample to be collected is calculated to yield a target measurement reproducibility considering the fundamental error associated to the sampling of heterogeneous material. This paper demonstrates that this practice is partly valid if one does not account for the time variation of the ore composition during the day. The concept is demonstrated using samples collected on a 30 minute basis from different streams of a gold ore concentrator. Results show that depending of the natural variability of the stream characteristics the mass of the daily samples may not be the critical variable to obtain reproducible measurements. On the other hand the number of cuts taken during the day could impact on the variance of the measurements obtained from daily samples.IntroductionMineral processing plants may treat several thousand tons of ore every day to produce concentrate or impure gold ingots. The operation and performances of these plants are monitored on a daily basis through the collection of ore samples from various streams of the processing circuit. The samples are prepared and assayed to obtain the concentrations of target elements that are subsequently used to calculate the mass flowrates in the streams of the circuit and ultimately the distribution of the target metals for the estimation of the plant performances (Morrison, 2009; Lachance and Leroux, 2016).The acquisition of representative and reproducible samples is therefore the first step in the characterization of plant performances. The term representative sample is used here to indicate an unbiased sample, i.e. a sampling procedure that does not introduce a systematic error. Rules for the collection of unbiased samples are reviewed in the literature by different authors (e.g. Morrison, 2009) and are not discussed in this paper. The term reproducible indicates the dispersion of the measurements around the average value of a characteristic of a stream meets an acceptable level of variance. The reproducibility of a measurement process (sampling and analysis) is assessed by the relative standard deviation or coefficient of variation of the measurement that is a function of the sampling and assaying errors (Morrison. 2009; Gy, 1979). Usually the focus is put on the fundamental error of sampling whose variance can be controlled by the choice of the primary sample mass or adequate particle size reduction during the preparation of secondary or tertiary samples extracted for the chemical analysis. When a sample is taken from a stream that exhibits a time varying characteristic, the obtained measurement exhibits a variability that is not only a function of the sample mass but also of the natural variability of the ore in the sampled stream. This paper examines this aspect of the sampling of a time varying process on the reproducibility of composite samples for a day of production."

Jan 1, 2017

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By Lopatka. M. J.

This paper presents the results of 3 tons skid steer 6x6 wheel robot drive system field tests. The aim of the investigation was verification of assumed data for drivetrain diesain and forces identification in the drivetrain system during maneuvering and crossing obstacles. Robot has hydraulics drive system with motors in the wheels and hydraulic suspension system. The neded drive torque on wheels was determined by pressure measurnig on motors.

Aug 1, 2013

By Neri Roux, Chris Budgell, Allan Cramm, Leo Cheung

"Anaconda Mining Inc. is investigating potential improvements and expansions to their operating plant located on the Baie Verte Peninsula in Newfoundland. An extensive batch and continuous bench scale testing program was launched to investigate the efficiency of cyanide destruction under different conditions in order to improve tailings handling. The primary objective of the cyanide destruction study was to apply new technologies to develop a novel cyanide destruction system.Effluent and slurry from Anaconda Mining Inc.’s Point Rousse Project was received at RPC where test work was conducted. Various sodium metabisulfite (MBS) dosages were evaluated and the use of utilizing ozone and ultra violet (UV) light to oxidize cyanide was investigated. All the data was evaluated and mass balances were compiled to develop several flowsheets. Overall encouraging results were found using a combination of ozone and MBS.IntroductionAnaconda Mining Inc.’s Point Rousse project includes an operating gold processing plant located on the Baie Verte Peninsula in Newfoundland which is in the process of improving and expanding. This plant comprises of milling and flotation followed by cyanide leaching in order to extract the gold. The residue from cyanide leaching is filtered by drum filters prior to being clarified for the Merrill-Crowe process. Once the gold has been recovered by the Merrill-Crowe process the effluent is filtered by filter presses and the resulting filtrate as well as the solids from the drum filters are detoxified prior to being pumped to the tailings pond along with the flotation tailings.The entire process is very dependent upon the efficient destruction of cyanide in the effluents and successful tailings handling. Substantial amounts of effluent are delivered to tailings ponds after gold extraction which could create environmental problems if the regulations are not met. Environmental regulations stipulate that final effluents contain no more than 1 mg/L Total CN.The detoxified tailings of the Point Rousse project are produced by the INCO SO2-Air circuit depicted in Figure 1. These detox tailings contain 10 mg/L Total CN at that point of the circuit and this was selected as the target to be matched while reducing overall MBS consumption rates from 3.2 g/L per minute. Prior to detoxification, the filter press tailings contain 520 mg/L Total CN while the drum tailings contain 29 mg/L Total CN."

Jan 1, 2017

By D. Bouchard, M. Forté, A. Charette

A transparent replica of a casting die was built to achieve a better understanding of the filling mechanisms of aluminum in high pressure die casting. Water and tomato paste were respectively used as analogues for the Newtonian liquid aluminum and the non-Newtonian semi-solid aluminum. The transparent die was installed on an industrial casting press and filling was filmed with a high-speed camera. Differences between the Newtonian and non-Newtonian fluids are presented and discussed.

Jan 1, 2006

By H. H. Gardner

INTRODUCTION THE problem of mechanization is one of the most vital in the minds of Alberta coal operators today. In these times of constantly increasing operating costs, any way of decreasing the cost of a ton of coal must be explored to the limit. There seems no better field for such effort than the successful application of power to the mining and loading of coal. We are fortunate in having neighbours to the south who have made .remarkable progress in recent times along these lines. Higher tonnages per man have resulted in higher wages to the employee and lower cost to the employer. It might seem that our problems could be solved merely by imitating our neighbours. Unfortunately, neither practice nor experience substantiate this conclusion. It is with the purpose of reviewing our accomplishments, as compared with practice in the United States, and at the request of the Prgoramme Committee for this meeting, that this paper is written. The Committee believes that such a general discussion and comparison may well lead to further advances in our mining methods. SUMMARY OF PRACTICE IN THE UNITED STATES A visit to the highly mechanized coal mines of the United States is always most instructive and encouraging.

Jan 1, 1951