Search Documents

By W. L. Nelson

The orebodies at Copper Mounta1n lie along and within a few hundred feet of the contact of an intrusive stock of gabbro with a series of bedded volcanic rocks of the Nicola formation. These. orebodies are all entirely within the volcanic series but in many cases the centre line of the orebody at depth is directly under the gabbro contact at the surface, due to a slight overhang of the gabbro. The gabbro and volcanic rocks are cut by a number of faults and fault zones which did not materially affect early mining operations, but, as undeground openings increased in size, the faults became more important factors in determining mining methods and procedure. Caving methods were adopted to take advantage of ground weakness in fault zones, and the effect of ground subsidence which resulted from the division of the ground 1nto large, independent blocks by faulting had to be considered in planning the sequence of mining of certain ore blocks. The faults have been divided into two classes: the longitudinal system and the cross faults, or 'breaks' as they are termed locally. In addition to the two classes of faults, the zones of parallel ore fracture also control mining procedure, but to a lesser degree, in regard to caving or ground subsidence. A third structural feature which influences mining procedure is the mine dyke system. The longitudinal or main fault system roughly parallels the gab? bro contact and is made up of a number of branches and auxiliary fractures. The main fault itself is essentially vertical, but there are a number of branches and fractures on each side of it which, though parallel m strike, may dip as flat as 50 degrees toward or away from the main fault. The full width of the main fault system has not been determined, but it is known to extend beyond the zone of mine workings. A marked schistosity follows the main fault and both schistosity and chloritic alteration have been noticed along the secondary faults of this system. Several prominent orebodies lie along the main fault and its branches. The influence of the main fault system on mining is probably related more to subsidence than to actual cavi.ng, although it is effective in both.

Jan 1, 1950

By A. Chaisantikulwat

Most solid-oxide fuel cell (SOFC) modeling emphasizes steady state cell operation. However, understanding the dynamic behavior is essential to predict the performance and limitations of SOFC power systems. In this work, we demonstrate a dynamic model of a SOFC, and we simulate a feedback control scheme that can maintain output voltage despite load changes. Dynamic response is determined as the solution of coupled partial differential equations derived from conservation laws for energy, mass and electric charge. From such a model, the step responses to system input variables can be determined. Low order dynamic models that are sufficient for feedback control design can be derived from the step responses. The development of the partial differential equation model is outlined, and the limitations of the control system are discussed.

Jan 1, 2005

By E. P. Cadwell

"Throughout the years Cyanamid has been a supplier of cyanide and a supplier of information to the mining industry. In general, the knowledge of mineralogy is greatly overlooked. Mineral deposits in the Western hemisphere have been exceedingly rich in the past but now they are becoming poorer. In other words, we will have to use our talents to the utmost to extract the precious metals and base metals from these ores. Modifications of some of the mineralogical equipment displayed here belong in the mill.Cyanidation of copper has been one of the main projects in our labs in recent years. De-rimming or de-filming of copper in order to upgrade copper concentrate was the main aspect investigated. A study was made as to how wide spread was the filming of secondary copper on pyrite, and to what extent it affected the copper industry. It was very wide.Often there is no conception as to what the minerals are. One open pit copper producer with a chalcopyrite ore was producing a copper concentrate with a 5% copper value whereas chalcopyrite contains 35% copper. They used primary and secondary grinding and a regrinding section. The ore contained about 8 parts chalcopyrite to one part of other copper minerals. In tests, a 3 1/ 2% copper rougher concentrate, cleaned without regrinding but conditioned with cyanide for a low contact time of 30 seconds produced a 30% copper concentrate with 90% recovery by removal of the film. It was of utmost importance that some quantitative mineralogical analysis be made before flow sheet changes were made. Every man should be trained to do his own microscopic examination in order to get quick answers. The fundamental thing in all mineral dressing is to first of all know the minerals and the mineral associations."

Jan 1, 1964

By A. W. Jolliffe

AEROPROSPECTING may be defined as the application of the air view to the search for mineral deposits. The term is suggested as a preferable alternative to either aerial prospecting (which may be confused with areal prospecting) or air prospecting. The air view may be obtained by visual observation from an aircraft or by examination of air photographs; each has its particular advantages and disadvantages. Aeroprospecting should be regarded only as an aid to, and not as a substitute for, accepted prospecting methods ( l ). The Precambrian region north of Great Slave lake consists of two well defined physiographic units, a feature first noted by J. T. Wilson (2). The boundary between these lies close to the north shore of the east arm of the lake and extends northwesterly near Spencer, Beniah, Carp, and Ghost lakes (Figure 1). South and west of this line, exposed bed-rock makes up the greater part of the land area; eskers are very rare, and overburden is largely limited to rock-walled valleys and depressions. North and east of the line, outcrops are rare or absent, eskers are abundant, and most of the surface consists of drumlin-like drift hills, elongated parallel to the direction of ice movement (Figure 2). Where this boundary passes through the area shown in Figure 1, it lies near the 1,200-foot contour and may mark the maximum extent of the lake or sea arm present in this vicinity toward the end of the Pleistocene period. For convenience, the first area may be called the 'bed-rock belt' and the other the 'drift belt'.

Jan 1, 1945

By J. E. Dutrizac

The dissolution of low-iron sphalerite, (Zn,Fe)S containing 0.08% Fe, in ferric sulphate-sulphuric acid media was investigated using closely sized fractions of crushed sphalerite crystals and sintered disks made from the crushed crystals. Linear kinetics are observed, and the predominant reaction products are ZnSO4, FeSO4 and elemental sulphur. The leaching rate increases systematically with increasing temperature, and the calculated apparent activation energy is 56 kJ/mol for the sized sphalerite and 54 kJ/mol for the sintered disks. The relatively high apparent activation energy suggests that the rate is chemically controlled, a conclusion supported by the insensitivity of the rate to the disk rotation speed. The rate increases as the 0.22 power of the Fe(SO4)1.5 concentration, and as the 0.22 power of the H2SO4 concentration. However, in the absence of ferric ions, the rate increases more significantly with increasing H2SO4 concentrations, and relatively rapid rates are observed in solutions containing >0.5 M H2SO4. In 0.1 M Fe(SO4)1.5-0.3 M H2SO4 media, the measured rate decreases with increasing sulphate concentrations, added as Li2SO4. The rate of dissolution of low-iron sphalerite is promoted by dissolved copper concentrations as high as 800 mg/L. In contrast, dissolved silver, even in the 0-2 mg/L concentration range, significantly retards the dissolution of the low-iron sphalerite.

Jan 1, 2008

By T. W. Wlodek

Abstract A simplified method of fatigue testing full-dimension, as-rolled, non-machined, mining drill rods is very desirable to the mining and steel industries in the classification of steels available on the market, through the evaluation of their fatigue limits and endurance strength. In this paper one such simplified method is presented and analysed. The preliminary results show many advantages of this method, such as simplicity and constancy of loading. The type of loading applied more or less simulates the working conditions of the outside fibres of the mining drill rods. Additional advantages of this method are the possibility of testing under dry and wet conditions, its quietness, and its ease of operation. Specially designed adaptors and specially applied techniques of fixing and preparation of samples make possible the breaking of a quarter-octagon hollow drill rod in a free length of uniform section in a rotating beam machine. At first glance this seems to be difficult to achieve. In the first preliminary test three different lots of steel were used. S-N curves under dry conditions were determined. These curves permit of the classification of the drill rods on the basis of the fatigue limit and endurance strength of the outside fibres of the metal, which is dependent to a greater or lesser extent on the effect of surface decarburization, surface imperfections, and special surface treatments. The average slope of the S.N curve in the damaging zone, and the fatigue limit in equal tension-compression rotating bending, were determined for SAE 1080, chromium-molybdenum and nickel-chromium-molybdenum mining drill rods. INTRODUCTION The fatigue limit and the endurance strength of mining drill rod steels are of interest to both the mining and the steel industries. These industries are greatly interested in lowering the cost of mining by reducing the consumption of these steels per ton of ore exploited.

Jan 1, 1951

By Alfred W. G. Wilson

MR. F. E. LATHE: In studying any subject whatever, one should at least occasionally stand back from the canvas, as it were, and take a broad view of the picture. It is such a view of the subject of industrial minerals that Dr. Wilson has given us today, and, in consideration of our efforts to utilize Canada's resources to the utmost in the present emergency, it seems most timely. I shall confine my remarks on the subject to the resources of the atmosphere and hydrosphere. We seldom stop to realize our dependence upon the atmosphere, not merely as a source of the oxygen we breathe but also of other indispensable elements. As recently as the beginning of the present century, grave concern was felt lest the rapidly increasing population of the world should ultimately starve for lack of the nitrogen required for crop growth. I recently noticed a reference to the Scientific American for March, 1890-just fifty years ago-in which an account is given of work on the fixation of nitrogen, which, said the article, "leads to the conclusion that while cyanides and ammonia may be thus produced experimentally, there are as yet insuperable difficulties in the way of adapting those methods to industrial purposes". Y et, in the early part of the present century, the development of the arc, cyanamide, and synthetic ammonia processes of nitrogen fixation was such as to remove, for all time to come the possibility of a shortage of nitrogen. Today, the atmosphere is by far our greatest source of nitrogen, and the capacity of the nitrogen fixation plants of the world is at least 4,000,000 tons annually-much more than can at present be utilized. Pure oxygen or oxygen-enriched air offers great possibilities in metallurgy and industrial chemistry, but, so far, little application has been made. In a paper presented to the Institute in 1926, 1 pointed out the theoretical savings which could be effected by the use of oxygen in burning carbon-when the gases pass off at 2,460°F., the fuel saving is no less than 50 percent. The use of oxygen on a commercial scale is intimately tied up with the question of refractories, but we should not forget that the possible changes in metallurgical practice by the use of oxygen are truly of revolutionary character.

Jan 1, 1940

By Bonnie Cooper

3D printing by fused deposition can be used on lunar soil. The soil can be precisely size-separated to make the 3D printing process work efficiently. Using a MASER instead of a LASER would allow us to use the finest fraction of lunar soil, AS-IS, to manufacture things on the Moon.

May 1, 2013

"IntroductionThe Chairman, in his speech to this body last year in Montreal, stated that the Dominion Coal Board looked to and depended upon the Bureau of Statistics for statistical material, and the Bureau does collect and publish monthly and annual data on coal. It may therefore be asked why an officer of the Dominion Coal Board should prepare and give a talk on statistics.I would explain that it has been our experience in the Board that, since the supply and consumption of coal in Canada is subject to a seasonal ebb and flow, it can be more profitably studied on the basis of a twelve-month period ending on March 31st than of a calendar year, since the end of March does represent a fairly stable end point in this ebb and flow. The figures are not prepared or published by the Bureau on that basis and it has therefore been thought that a presentation on this fiscal-year period would be of interest. The Bureau of Statistics has agreed that this may be valuable and all the data here presented are based on the reports secured from various sources by the Mining, Metallurgical and Chemical Division, Dominion Bureau of Statistics. The only contribution by either myself or the staff of the Dominion Coal Board has been the tabulation in a different twelve month period, and the comments upon the picture presented.It should be noted that the data for the month of March, 1950, are not available in all cases and consequently the figures for that year contain an estimate for this month."

Jan 1, 1950

By J. A. H. Church

MR. J. A. H. CHURCH: The salient feature would seem to be that the thickness of the seam, in our coals at any rate, is the main factor in predisposition to spontaneous ignition. The evidence, incomplete it must be admitted, in the Saskatchewan and British Columbia fields, and complete in the Alberta field to my mind, shows this up very strongly. The German report on the upper Silesian coal fields definitely fixes the critical thickness at 13 feet, the British report goes far beyond this figure by stating that liability to ignition increases with the thickness of the seam over four feet. Before discussing the Alberta fires it would be well to note an error on page 12 -the probable cause of the fire in the Frank Mine should read "Spontaneous near fault. Heating first discovered 1909". Of the six fires attributed to spontaneous ignition all the seams were identical or in excess of the critical thickness mentioned in the German report. If there be any reason in the foregoing it is high time some forethought were taken to adopt some definite system of laying out the workings of such seams not so much on the outcrop districts as with a view to the future operation to the dip. Seams approaching 13 feet in thickness which to date have shown no disposition towards heating during the extraction of the outcrop areas may well cause infinite trouble or indeed total loss when the ventilating pressures increase as increase they must to the dip. This state of affairs can be combatted only by the adoption of a correct system of working and the provision of numerous airways of as large an area as may be compatible with the physical characteristics of the particular seam.

Jan 1, 1923

By Brian E. Robertson

"This paper summarizes work carried out at the Dome Mine to mechanize the mining of narrow veins of less than 1.5 m in width by the introduction of new mining methods and specifically designed electric LHDs.Extensive mining trials have been conducted using sublevel blasthole, modified Avoca, and resuing mining methods. The introduction of the Microscoop and the Jarvis Clark remote, radio-controlled scooptram has increased mucking productivity.As a result of this work, additional narrow vein stopes are now being prepared for production. In the future, narrow vein stoping wil lprovide a greater percentage of the total mill tonnage.IntroductionThe Dome Mine, which is owned and operated by Dome Mines Limited, is located at Timmins, Ontario. Production has been continuous since 1910 and in 1984 was increased from 1814 to 2721 tonnes per day.At least six distinct ore types have been recognized at the mine. In general, these orebodies can be broadly categorized into wide and narrow deposits. The wide deposits are approximately lenticular in shape and vary in width from 10 m to 40 m. The narrow orebodies consist of quartz and quartzankerite veins ranging in width from a few centimetres to six metres. The average dip of the veins is 65 degrees.Since the I970s, mining activity has been largely concentrated in the wider orebodies using highly productive open sublevel blasthole and mechanized cut-and-fill stoping methods. With the demise of shrinkage stoping in 1975, investigations were initiated to develop new mining methods and introduce LHDs - truly designed for narrow orebodies. These investigations resulted in test trials of the sublevel blasthole, modified Avoca, and resuing mining methods. Consultations with equipment manufacturers and suppliers led to the development of the Jarvis Clark remote, radio-controlled electric scooptram and the introduction of the France Loader Microscoop."

Jan 1, 1986

By Xiaolin Cheng, A. J. Sinclair

"Norm calculation procedures originally designed principally for igneous rocks are very rigid in their application and, in general, do not utilize important alteration minerals. For instance, volatile components are essential constituents of many metasomatic rocks but either are not used or are not used effectively in determining normative minerals by the CIPW norm or Niggli-Barth norm procedures. Our approach to determining norms for metasomatic rocks allots all major, minor and volatile constituents to a set of standard normative minerals which are commonly observed as products of hydrothermal alteration. A useful procedure is to have a metasomatic norm approximate the mode as closely as possible. Petrographic information helps to provide the necessary mineralogical constraints. With the recognition of an immobile component and knowledge of sampling and analytical errors in lithogeo chemical data, it is possible to recast norms into amounts of alteration minerals relative to a given amount (100 grams) of parent rock. Combining these results with the calculations of absolute loss or gain of individual chemical constituents and considering errors (e) for an appropriate confidence level, an overall (net) material exchange equation can be presented as follows:<equation>where all items have extensive units (e.g., grams). The model includes the initial and final mineralogy of rocks (evident in the field) as well as gains and losses of specific elements. Only those constituents whose calculated losses and gains are significantly different from zero are retained in the above model, and only the normative minerals with abundances significantly different from zero are included in the model (equation). One advantage of the chemico-mineralogic model is that parent rock and product are modeled in mineralogical terms that are familiar to and easily usable by exploration geologists."

Jan 1, 1995

By Michel Noël

This paper presents a partial compilation of adopted measures of waste rock dump closures at mine sites located in Canada and Alaska, where the climate includes cold winters. The paper also presents the selection process that was followed for some of those mine sites. Mining operations usually generate waste rock that can sometimes result in very large quantities. Additionally, the nature of the ore body and the host rock will often introduce environmental impacts. These impacts need to be managed not only during the operations but also in the long term. Mine closure plans consequently have to address the long term issues that sometimes require perpetual treatment. Closure planning often involves the evaluation of risks associated with environmental and financial liabilities. It needs to consider the science, some common definition of objectives, and there will be a need to manage resources and schedules. Closure planning is essentially an exercise in constrained decision making. A performance and risk based ranking matrix is often developed during this selection process to identify the preferred option(s). The case studies presented in this paper provides a few examples. The level of knowledge on acid rock drainage from waste rock dumps has increased considerably over the past decades. It did not necessarily increase the level of complexity of the adopted closure methods, as the selected closure methods are often kept simple. A common approach consists of stabilising the slopes of the waste rock dumps material by resloping and then covering the waste rock with a growth media to support vegetation. Such covers prevent direct contact of animals with the waste rock material, minimise erosion and reduce infiltration to various degrees. The inclusion of water treatment is obviously dependent on the water quality being released.

Nov 1, 2008

By M. Proulx

"RÉSUMÉ Le diagramme ternaire Al2O3-Sr-Y est un nouvel outil servant à l’exploration de gisements de sulfures massifs volcanogènes (SMV) archéens. Le diagramme permet de discriminer entre les roches volcaniques à minéralisations à zinc dominant (domaine Zn+) et celles à minéralisations à cuivre dominant (domaine Cu+), ainsi que les roches volcaniques ayant subi une chloritisation hydrothermale pouvant aboutir à la formation de chloritites associées aux cheminées d’altération (domaine Cl+). Ces trois domaines délimitent des zones d’influence géochimique ou d’empreintes hydrothermales résiduelles ou fossiles produites par les cellules de convection hydrothermales générées par des magmas. Le diagramme permet aux sociétés d’exploration de déterminer de façon peu coûteuse la fertilité potentielle des roches volcaniques archéennes en ayant recours à leurs bases de données et aux résultats de leurs analyses de terrain, sans aucune manipulation des données. Le diagramme ne s’applique pas aux SMV aurifères.ABSTRACT The tertiary diagram Al2O3-Sr-Y is a new tool to explore Archean volcanogenic massive sulphide (VMS) deposits. The diagram can be used to discriminate between the volcanic rocks where zinc is the dominant mineralization (Zn+ domain) and the rocks where copper is the dominant mineralization (Cu+ domain), as well as the volcanic rocks that were subjected to hydrothermal chloritization that could have led to the formation of chloritites associated with alteration chimneys (Cl+ domain). These three domains define the zones of geochemical influence, or residual or fossil hydrothermal footprints produced by hydrothermal convection cells generated by magmas. Exploration companies can apply the diagram to determine, at low cost, the potential fertility of the Archean volcanic rocks by using their databases and the results of their field analyses, without any data manipulation. The diagram does not apply to gold-bearing VMS deposits."

Jan 1, 2015

By Xiaolin Cheng, A. J. Sinclair

"Abstract - Norm calculation procedures originally designed principally for igneous rocks are very rigid in their application and, in general, do not utilize important alteration minerals. For instance, volatile components are essential constituents of many metasomatic rocks but either are not used or are not used effectively in determining normative minerals by the CIPW norm or Niggli-Barth norm procedures. Our approach to determining norms for metasomatic rocks allots all major, minor and volatile constituents to a set of standard normative minerals which are commonly observed as products of hydrothermal alteration. A useful procedure is to have a metasomatic norm approximate the mode as closely as possible. Petrographic information helps to provide the necessary mineralogical constraints. With the recognition of an immobile component and knowledge of sampling and analytical errors in lithogeochemical data, it is possible to recast norms into amounts of alteration minerals relative to a given amount (100 grams) of parent rock. Combining these results with the calculations of absolute loss or gain of individual chemical constituents and considering errors (e) for an appropriate confidence level, an overall (net) material exchange equation can be presented as follows:SMineralparent rock ± e + SConstituentgained from solution ± e= SMineralaltered rock ± e + SConstituentlost from wall-rock ± ewhere all items have extensive units (e.g., grams). The model includes the initial and final mineralogy of rocks (evident in the field) as well as gains and losses of specific elements. Only those constituents whose calculated losses and gains are significantly different from zero are retained in the above model, and only the normative minerals with abundances significantly different from zero are included in the model (equation). One advantage of the chemicomineralogic model is that parent rock and product are modeled in mineralogical terms that are familiar to and easily usable by exploration geologists."

Jan 1, 1995

By Erica J. Wanless, Ghislain Bournival, Seher Ata, Jose Hamilton Tavares

In froth flotation valuable particles are captured by bubbles and transferred to a froth layer where bubbles are in close proximity. Bubble coalescence frequently occurs in flotation, especially in the froth layer. The coalescence of two bubbles causes a release of energy, which may expel particles from the bubble surface. A series of experiments were carried out to determine the effect of bubble interfacial properties on the detachment of particles upon the coalescence of capillary-held bubbles of 2 mm in size. The interfacial properties of the bubbles were changed by the addition of low molecular weight alcohols, namely 1-pentanol or methyl isobutyl carbinol (MIBC). Using esterified glass particles (? = 43 °) with a 10 % and 90 % cumulative passing diameter of 47.2 and 92.5 µm, respectively, as model particles, it was found a certain concentration of frother, different for each additive, is needed in order to observe a reduction in the detachment of particles. In the presence of frother, the detachment was evaluated at approximately 65 % which was a considerable reduction in the detachment compared with the value of approximately 85 % found in the absence of frother. Frother molecules changed the properties of the airwater interface. Upon the coalescence of two bubbles, the release of energy caused the merged bubble to oscillate; effectively resulting in the detachment of particles. The addition of frothing agents augmented the elasticity of the bubbles, which appeared to be related to the detachment of particles. Whereas frothing agents are generally used to prevent bubble coalescence and stabilise the froth phase, only transient stability is imparted. The results suggested that an additional role of frothers in flotation is to decrease the detachment of particles from bubble surfaces. The type and concentration of frother can be strategically selected to improve metallurgical recovery as an economic incentive.

Jan 1, 2016

By Randolph A. Pax

"The internal operation of a tumbling mill is a very hostile environment and precludes the sustainable operation of internal sensors to measure the mechanisms of charge motion and breakage events. Instead indirect methodologies are required to expand the current understanding developed within a framework of perfect mixing of the mill contents. A number of measurement approaches have been successfully used to explore the operation of SAG mills including strain instrumented lifter bolts, mill shell strain measurement and thermal (energy balance) of operating mills.Early acoustics measurement was developed by Hardinge using a 'microphone' located close to the expected toe location. This signal was an indicator of the mill fill. Improvements were implemented with the use of two microphones straddling the toe location to try to increase the sensitivity of the measurement and reduce ambiguities. Further improvements included a filtered signal indicative of steel interactions. Unfortunately, the mechanisms of signal generation and the complexity of the processes do not provide a consistent signal.In recent years, advanced acoustic measurement using arrays of microphones utilising signal processing techniques have been implemented as SmartNoise and validated on over 30 mills. This paper will discuss the results obtained with signals such as water holdup, mill shell steel hits and two each of the toe and shoulder angles. An estimate of the internal mill component wear rates is also accessible.Advanced acoustic measurements with wide bandwidths when combined with physics models and process understanding has achieved a step change in the understanding of the dynamic internal operation of a tumbling mills on time scales of 80 ms. These techniques have been used extensively on SAG mills, but have also been applied to FAG and ball mills. Acoustic measurement is used for the rapid diagnosis of mill conditions and holistic control for optimisation and stability."

Jan 1, 2016

By J. G. Bensley, K. S. Detheridge

"Many plants use computers for process control and most have computerized Management Information Systems but few have been able to have these systems interact with one another. Developing this system interaction is not a one-step process but requires careful planning and implementation. This paper describes two projects that were implemented to provide the bridge between the process control and management information systems of Cominco Limited. Both projects include the replacement of essentially process control systems installed in the late 1960s. These original systems provided an enhanced level of control in the form of Direct Digital Control (via computer/manual analogue control stations) and a management reporting capability of process data. The experience gained from the use of these systems over a period of fifteen years formed a basis for the evaluation and planning for the new systems. The new systems were commissioned in 1985 and 1986 and operating and further developments leading to a totally integrated process information and control system are underway. INTRODUCTIONThe concept of hierarchical control involves a control structure consisting of a number of defined levels. Each level performs a defined function with information consolidated and combined as it moves up through the hierarchical structure. The commonly accepted structure of a hierarchical control system echoes the structure of the plant which is being controlled. Referring to Figure 1:Level 0 - Sensors and ActuatorsSensors and actuators, such as thermocouples and flow control valves, interface directly to the process and are generally connected directly to the controllers or multiplexers at Level I.Level 1 - Regulatory ControlThis level provides basic PID control (proportional/integral/ derivative) typically using microprocessor based controllers and programmable controllers for digital control of motors and machines. Systems at this levelare usually segregated by plant unit, e.g, crushing, flotation, drying. Control is concentrated on achieving optimum conditions for a particular feed rate."

Jan 1, 1989

By H. E. Wilde

"Zinc has been used for many years as a galvanic coating for the protection of steel. Electrochemical measurements show that zinc actually overprotects steel. The corrosion rate of DQSK (drawing quality semi-killed) steel in air saturated salt water was determined as a Junction of applied cathodic potential. The resulting data indicate that at a critical cathodic over potential of - O. 725 Vsce an acceptably low corrosion rate of less than 1 mpy occurs. Using the developed criterion, alloys of Zn/X and AL/X were produced and evaluated in galvanic contact with steel in a standard laboratory test. The results indicate that Zn /Mn, Zn /Co, AI/Mg/Si and AI/Mg/Ge alloys offer excellent galvanic protection along with (a) no hydrogen evolution, and (b) improved dissolution life over Zn coatings.IntroductionZinc coated (galvanized) steel has been successfully used in applications where bare (or painted non-galvanized) steel would suffer corrosive attack. In general, galvanic coupling to zinc, as either an anode or a coating, is an effective means for combatting steel corrosion. Because of this, the use of galvanized steel has increased markedly, stimulated primarily by automobile manufacurers seeking to extend the corrosion warranties on automobiles(1).Although effective, zinc coatings are not without a number of drawbacks which warrant efforts to improve them. For example, because of the widely differing electrode potentials between zinc and steel ( - 1.05 Vsce and - 0.60 Vscc, respectively, in air saturated NaCl solutions), the zinc corrodes at a rapid rate to protect the steel. This is reflected in the limited lifetimes of galvanized unpainted siding. The basic electrochemistry controlling the situation is shown in Figure 1, for a system controlled by oxygen reduction. The zinc corrodes sacrificially to protect the steel, while cathodically polarizing the steel to a potential near that of zinc&apos;s open circuit anode potential."

Jan 1, 1990

By Robert B. Parsons

"Considering the traumatic events of Canadian mining taxation of the 1970s, one wonders at the sanity of anybody who tries to predict what the 1980s might hold for the tax structure of the mining industry. Yet, the author agreed to tackle this task when called upon to do so at the annual meeting of the Quebec Metal Mining Association in June. The text of this ""daring"" speech follows.IntroductionI have been asked to play the part of the oracle at Delphi, and to predict what the 1980s might hold for the Canadian mining industry in terms of taxation. To appreciate the challenge of this difficult assignment, try to imagine someone in my position back in 1972 attempting to forecast the balance of the 1970s. I daresay that ten years ago nobody could possibly have conceived of the devastating and casualty-ridden rollercoaster ride that mining taxation actually took in the 70s. Nevertheless, I shall examine the entrails and try to shed some light on what might happen during the balance of this decade as far as mineral taxation is concerned.If one were to retreat deep into history, one would find that taxation generally served one purpose-namely, to raise revenues for the government. More recently, an important second function has emerged: taxation is increasingly being used as a fiscal tool-a tool intended to mould and shape future events in order to accomplish certain economic, social and political objectives. It is these two main forces-the need (or desire) for revenues and the perceived convenience of using taxation as a fiscal tool-which will continue to shape the tax structure of the future.In our assessment of where taxation of the mining industry may be headed, we should be able to learn something by looking at where we have been."

Jan 1, 1982