Search Documents

By F. E. P. PEARSON

Sandstone quarried from an island in Lake Winnipeg is barged 130 km to a processing plant at Selkirk on the Red River. The stone is white, poorly consolidated, and consists of rounded quartz grains of high natural purity. It is an important supplier of silica in Western Canada for glass, fiberglass, foundry and other industrial uses.

Jan 1, 1984

By RAYMOND C. HARTVIKSEN

The Drumbo Mine is located near Highway 401 between Woodstock and Kitchener in southwest Ontario. The tabular flat-lying gypsum bed is between 1.5 to 2.4 m thick and is situated near the base of the Salina Formation, about 116 m below surface. The mine is owned and operated by Westroc Industries Limited. The 3.8 m diameter shaft was drilled using a Hughes CSD 820 drilling rig and a liner sinking technique new to the North American continent. The shaft was completed in the fall of 1977, and remaining facilities were finished in the fall of 1978. Gypsum production started in December 1978, employing the conventional room-and-pillar method of mining.

Jan 1, 1984

By D. W. Morgan, K. W. Downes

"OVER half a million tons of chromite ore is used annually on the North American continent, all of which is imported from overseas. Chromite is essential in the manufacture of stainless steel, armour plate, and tool steel, to mention only three important uses. It is, therefore, a strategic mineral, and every effort should be made to discover a means of utilizing our domestic supplies.Both Canada and the United States possess deposits of chromite, but they are low grade with respect both to their chromium content and to the ratio of chromium to iron. Mechanical concentration can improve the chromium content •by rejecting gangue, but chromium concentrate produced is still lower in chromium than imported chromite and, more important, the ratio of chromium to iron is only about half that in the imported material. At present, a chromium to iron ratio •of 3:1 is desired by industry. To obtain this .ratio in the case of domestic ores, a chemical attack on the chromi'e is necessary."

Jan 1, 1952

By Ed Labelle, Terry Overton, Gary Bell

"LocationThe Miller Minerals lime and limestone production facility is located in the Temiskaming district of Ontario at Hailey bury on the west shore of Lake Temiskaming. Located less than 300 km from Sudbury, Timmins, Rouyn-Noranda and Val d'Or, the plant is very well situated to market products to the mining, pulp and paper, and environmental industries. Being located a few kilometres from the Trans-Canada Highway and the Ontario Northland Railway adds to transportation efficiencies.ProductsAt Miller Minerals, two principal products in various sizes are produced, which are limestone (CaC03) and quicklime (CaO).HistoryProduction of limestone products began in 1979 at this quarry site. During the 1980s, limestone products were marketed to a variety of applications for mining, forestry, environmental and agriculture applications. In 1990, the production of quicklime products began, following the commissioning of an Italian-designed vertical shaft calcining plant. During the 1990s, both quicklime and limestone products were produced to meet the customers' demands.From the quarry's conception until 1992, the operation was owned and operated by Dymond Clay Products. In 1992, it was purchased by Miller Paving Ltd. of Markham, Ontario, and became a key part of the company's industrial minerals sector of business. Other Miller interests include dolomite, cement, paving materials and waste management."

Jan 1, 2000

By Bradley Stoughton

The magnetic oxide of iron, F eO4 , contains a theoretically larger amount of iron ( 72.4 per cent.) than any other commercial ore. It is probable that it has originated in many cases by the prolonged exposure of the hydrated oxide, ZF e20 a + 3H20 to heat and pressure which converts it first into hematite, F e20 3, and then into magnetite. It would thus appear as if nature had already done part of the work of removing all the oxygen and that magnetite should be relatively easy to reduce. That it is, in fact, less reducible than either limonite or hematite, is due chiefly to its dense and compact physical structure, which makes it less pervious to the furnace gases, and also to its characteristic action in resisting crushing to a uniform size, with consequent irregularity in reducing conditions within the furnace. The net result is that the magnetic oxide requires more fuel and more time for its reduction in the blast-furnace than any other iron ore of similar iron content and physical condition. There is another very important reason why the smelting of magnetite is more costly than that of hematite, and its treatment viewed with a great deal of adverse prejudice by blast furnace operators, namely, that magnetite decreases the proportion of heat developed by the fuel in the stack of the furnace, and increases the already excessive heat requirements of the heart.

Jan 1, 1924

By Z. D’Amico

"IntroductionWE HAVE HEARD quite a lot recently on newer methods -of supporting roof, such as roof bolting or the use of metal props and •booms, but, with the exception of roof bolting, these methods are confined mostly to comparatively low, regular seams and even .bolting cannot be used to hold soft sides. Thus, where a seam of coal has great variations in thickness, or where it is faulty, or where the coal sides must be supported, nothing can wholly take the place of timbering with wood. This paper will deal mainly with the method of timbering such a seam, namely, the No. 3 seam mined by Brazeau Collieries, Limited, at Nordegg, Alberta, where the full height of a thick seam is mined in development. However, a few words on one or two other systems practised in Alberta when, in development work, a thick seam is only partially mined, should be of interest.Examples of Timbering in High SeamsThere .are several methods in use today for dealing with high seams of coal. The most popular is to develop the seam by driving road-ways in the coal by some conventional method, usually recovering the full thickness of the seam on the retreat. The following examples illustrate two variations of this method.In Figure I we have a thick •seam of friable coal, with a good roof, pitching about 30 degrees, which is being mined by taking the upper part of the seam in the development work, leaving the •bench coal in place. Figure 1A shows a section through a room."

Jan 1, 1954

By D. MacGREGOR, VERA TUREK

The St. Canul and Ste. Scholastique orthoquartzite sanrjstone deposits are located within the Potsdam Formation near Montreal. The sandstone lies on Precambrian basement and is Cam/3rian to Ordovician in age. The Potsdam Formation shows two distinct stages of development. One created a deepwater facies represented by impure, limey or shaley sandstone; the other produced a shallow facies composed of grey, highpurity sandstone. The shallow-water orthoquartzitic sandstone at St. Canul is being mined and beneficiated by lndusmin Limited. The operation manufactures a wide range of silica products and supplies industrial areas of Quebec and Ontario with material for the glass, foundry, silicon carbide and ceramic industries.

Jan 1, 1984

By Mehmet F. Taner

"Abstract - "Les Mines Selbaie" is a large, generally low-grade, polymetallic (Zn, Cu, Ag, Au) "giant" volcanic-associated ore deposit in the Harricana-Turgeon belt, which is part of the northern Abitibi Subprovince of Quebec. Economically recoverable mineralization occurred in three zones: the A1 (open pit), A2, and B Zones (underground). The pre-mining resource was 54.9 Mt, including 8 Mt of sub-economic, locally silver-rich massive pyrite. In the Selbaie region, calc-alkaline andesitic volcanics form the "basement." The Brouillan Volcanic Complex formed within an islandarc setting on this regional basement. Evolution of this complex involved the formation of a felsic magma chamber and the development of a large caldera structure over the Brouillan batholith. Second- order linear and sub-parallel faults and rifts developed as a result of back-arc rifting/extension. The edges of these rifts were feeders for linear felsic volcanism (similar to fissural volcanism). During felsic volcanism, the feeder zones acted as conduits for hydrothermal fluids with associated pervasive potassic alteration. The alteration is characterized both vertically and laterally by well-defined quartz, sericite, K-feldspar and/or, locally, biotite halos, to produce a mushroom-shaped morphology. This K-feldspar alteration is not common in most other volcanic-associated ore deposits. Mafic dikes cut all of the geological units and appear to occupy earlier synvolcanic structures. Regional greenschist- assemblage metamorphism and pervasive deformation affect all units. Thrust faults moved part of the Brouillan batholith and basement units over the Mine Sequence. Although there is no relationship between the earlier mineralizing events and these late thrust faults, the thrust faults probably played an important role in location of ore lenses. Three types of mineralization are present: 1) copper-rich veins and hydraulic breccias; 2) disseminated and stringer, low-grade and high volume zinc-copper mineralization; and 3) finely laminated, massive, locally silver-rich pyrite mineralization within structural basins. At the bottom of these basins and at the contact of welded acid tuff (WAT) units, massive pyrite zones are locally enriched in zinc, and contain the possible vestiges of black smoker-like material. The ore metals were probably derived from leached basement andesitic volcanics in a hydrothermal system powered by one or more heat sources within the Brouillan Volcanic Complex. The Selbaie deposits are mainly characterized by: (1) the presence of small volcano-tectonic subsidence basins, which host chemical sediments and volcaniclastic materials; (2) pervasive potassic alteration; (3) locally high-grade silver mineralization (up to 1-2 kg/t Ag); and (4) the presence of random zones of Pb mineralization. The Selbaie deposits can be closely compared with the copper-rich Murgul deposits, which belong to the eastern Pontides metallogenetic province in Turkey. If conventional classification criteria for the volcanogenic massive sulfide deposits (e.g., Noranda, Mattabi types, and recent subsea floor deposits) are taken into account, the Selbaie deposits still exhibit many differences in terms of alteration assemblages, physical volcanology and some styles of mineralization (low-grade and large volume). Consequently, the "Selbaie" deposits belong to a new sub-type of volcanic-associated sulfide deposit, which may be used in future exploration programs."

Jan 1, 2000

By J. M. Harrison

"The Nor-Acme gold mine is near the shore of Snow lake, northern Manitoba, about 75 miles east of Flin Flon. The claims that form the nucleus of the present property were staked in 1927 by C. R. Parres, but it was not until 1941 that diamond drilling disclosed the potentialities of the deposit. In that year a large-scale drilling programme was begun under the direction of F. Ebbutt, of the Howe Sound Exploration and Development Company. Two orebodies were outlined containing about 5,000,000 tons of ore assaying $5.25 in gold per ton. In August, 1945, construction of the mining plant was begun.All information and interpretations contained in the following brief description of the deposit were obtained from surface mapping.GEOLOGYThe ore lies at the contact between a coarse, basic, pyroclastic rock, which is the hanging-wall, and grey, acidic lavas and sediments, which form the footwall. These rocks are cut by irregular basic intrusions that vary in composition from diorite to hornblendite, and by small acidic dykes . Tourmaline is locally common in the hanging-wall rock near the ore.The ore occurs in brecciated, silicified, and ·slightly carbonatized rock. Arsenopyrite is the main sulphide and the gold is associated with it. Pyrrhotite is locally abundant and minor pyrite, chalcopyrite, sphalerite, galena, and cubanite have been noted. Two orebodies are known, the Dick and the Toots. The Toots, which is much the smaller of the two, is about 1,000 feet west of the Dick."

Jan 1, 1954

By J. E. Rowland

NIOCALITE is a new mineral species which has been identified in rock from the Oka district, Quebec. It occurs as prismatic crystals up to l 0 mm. in length and I mm. in width, in coarse, white, crystalline calcite with associated apatite, diopside, biotite, pyrochlore, and niobian perovskite. The crystals of niocalite are light yellow in col-our and have a vitreous lustre. The optical properties of niocalite (I) are as follows: Biaxial negative -2V = 56° a = 1.700, [ ] = 1.730 Birefringence y -a = 0.030 Optic orientation: X = b, Z/\c 12°, Y , /\a = 32° The specific gravity is 3.32 and the hardness is approximately 6 (Mohs scale). A detailed analysis performed on 2.4 gm. of hand-picked material reveals that niocalite is essentially a calcium niobium silicate. Table I gives the result of the analysis. Crystals of niocalite, apparently suitable for X-ray diffraction work, were selected, and single crystal photographs were obtained using both Weissenberg and Precession cameras. Initial difficulties were encountered in interpreting these films, and in correlating the crystal data with the optical data. The in-consistencies were explained by the fact that every grain examined was twinned to some extent.

Jan 1, 1957

By M. Coleman, M. E. Reed

The control of feed delivery quality to the flash furnace remains an unsolved problem. Many operations around the world still have limited control of feed quality to their flash furnace. Schenck Process and WorleyParsons continue to work towards the ‘holy grail’ of simple quality feed delivering both radial feed distribution and pulseless feed delivery. Ten years ago they joined forces to offer a system based on then Clyde Process RotoFeed system which could deliver ground level installation, online mixing of materials, pulseless feeding direct to the burner, with good radial distribution. Unfortunately, this proved to be too large a step for the Flash Smelting community and met with resistance from the process owners. Since then the community has developed a range of options some of which have been implemented over this period. Despite these improvements there are still areas of concern including safety issues associated with concentrate leaks and spills, uncontrolled variations in feed rate including massive flooding events, intermittent distribution improvement and set up of the burner continues to be trial and error and hard to repeat the success in each burner campaign. These continue to impact flash furnace performance globally on a daily basis. Following the community reticence to pursue the complete solution a number of interim steps are now available to pave the way to the ultimate feed system. The mixing of material has been installed and is delivering line blended materials on a daily basis. This paper will investigate the developments over the last 10 years and discuss the pros and cons of this incremental step process for overall furnace control. INTRODUCTION Schenck Process and WorleyParsons have continued to interact and observe changes in the flash smelting industry and to consider application of the Clyde RotoFeed now incorporated in the Schenck Process ProStreamTM range for delivery of feed directly to the concentrate or matte burner. Schenck Process pneumatic injection from the Clyde Process range, ProStreamTM, utilises two types of volumetric feeders to accurately control the feed of material into an injection pipeline. These are referred to as the RotoFeed and RotoScrew technologies and the choice of feeder type is dependent on the characteristics of the material to be handled. The RotoFeed is generally used for finer, granular and powdered materials which cannot be accurately handled with a screw such as pulverised coal and copper concentrate, whilst the RotoScrew is particularly suited to coarser lump materials, particularly abrasive of cohesive materials like zinc powder, electronic scrap and metal ashes. Both units can operate at high pressures and many systems work at 3 to 10 bar with the occasional system working at 20 or 30bar for carbon to gasifiers. For the Flash furnace the ProStreamTM units can be used to deliver each of the furnace feed materials into a single line, mixing the materials homogeneously and live to the burner.

Jan 1, 2019

By S. C. Ells

Introduction An investigation of the bituminous sands of Alberta was begun by the Mines Branch, Department of Mines, in 1913. This investigation was interrupted during the period 1916-19, but was resumed in 1920. Work completed in October 1924 has included detailed topographical surveys of extensive areas, examination and sampling of principal outcrops, the mining of trial shipments, laying of demonstration pavements, and a study of methods adapted to the recovery of hydrocarbons from the crude bituminous sand. Bituminous sand consists, for the most part, of clear quartz grains, cemented together by petroleum residuum or bitumen. In form the quartz grains are most irregular, varying from sharply angular to smooth, waterworn shapes. The bitumen has a specific gravity of 1.018 and has a penetration of 9.00 mm. (77° F. 100 grams 1 sec.). The percentage of bitumen associated with the sand varies from 5 to 25 per cent. A large tonnage is available in which the percentage of bitqmen is 15 per cent or over. Production Up to the present time, production has been restricted to requirements for experimental .and demonstration work. The total quantity shipped for such purposes has not exceeded 750 tons.

Jan 1, 1925

Scope / Agenda ? What is Situation Awareness (SA)? ? Background on SA theory ? SA is critical in a wide variety of domains ? SA and human performance ? Consequences of poor SA ? Significant challenges for SA in mining operations ? Technology centric design ? SA-oriented design methodology ? Goal-Directed Task Analysis ? Design ? SA Measurement and Evaluation ? Applications of SA-oriented design

Aug 1, 2013

By G. H. K. Pearse

Sulphur is derived from both 'voluntary' and 'involuntary' production. The former category includes sulphur obtained from elemental sulphur deposits and from pyrite and gypsumanhydrite deposits. Sulphur in the latter category is produced by pollution abatement at fossil Juel plants and from treatment of metallic sulphides. Canada is the world's largest sulphur exporter and third largest producer. Main resources of Canadian sulphur are sulphurous fossil fuels, metallic sulphides and native sulphur. Only the first two sources have produced sulphur in Canada 10 date; the first source accounts for over 85% of total Canadian production. Future sulphur sources will be derived increasingly through pollution abatement and decreasingly through voluntary production.

Jan 1, 1984

By R. Sharma, I. Miskovic, S. Miskovic

Solvent extraction (SX) is a widely used method for the extraction of copper from pregnant leach solutions or other ionic solutions in hydrometallurgical applications. About 17% of total refined copper production worldwide is produced using SX followed by electrowinning (EW). Conventional SX units, such as mixer-settlers, consume a large amount of extractant, offer poor process control and yield low extraction efficiency. Extraction efficiency is poor due to low specific interface area, crud formation, emulsification, and slow phase separation stage. Micro solvent extraction (micro-SX) is a rapidly developing technology that provides an opportunity for improved process control, higher extraction efficiency, lower residence time and, as such, has a potential to reduce the environmental footprint of SX operation. In this research, extraction of copper ions in an acetate buffer media is investigated using D2EHPA with kerosene as a diluent. Chemical factors such as extractant concentration and ionic concentration of aqueous phase are varied to determine the optimum conditions. Subsequently, the extraction efficiency and reaction time of new micro-SX reactors are compared against previous bulk SX studies. Extraction in the microfluidic reactor was observed to be faster with a residence time more than an order of magnitude lesser than bulk SX. This study forms a prelude for developing new modular micro-SX units which will enable continuous, effective, and safe operation on a large scale. In future studies, numerical and analytical models validated through this work will help eliminate rigorous experimentation and enable faster design and fabrication of micro-SX units. INTRODUCTION Conventional industrial solvent extraction (SX) units such as mixer-settlers, extraction columns present various disadvantages. Low specific interfacial area, crud formation, and emulsification in industrial reactors lead to long extraction times and severely hamper extraction efficiency (Priest et al., 2011; Chen et al., 2017). Microfluidic extraction considerably improves upon the current extraction practices by (1) creating a large surface to volume ratio that enables rapid mass transfer across the interface, (2) better process control, and (3) easier separation of phases (Kashid, Renken, & Kiwi-Minsker, 2011; Ciceri, Perera, & Stevens, 2014). These factors establish micro-SX as a crucial mode for process intensification. Although, a micro SX unit has significantly low processing volume than conventional extraction methods, their throughput can be increased via massive parallelisation (‘numbering up’), which is an area of active research (Darekar, Singh, Mukhopadhyay, & Shenoy, 2016a; Kriel, Woollam, Gordon, Grant, & Priest, 2016).

Jan 1, 2019

By Unkown

The Province-wide road ban on movement of heavy loads has had the effect of curtailing or stopping development in several areas. In the Leduc area, the discovery well has been restricted in flow to only a fraction of normal due to limited storage space, but drilling at Imperial Leduc Nos. 2, 3, and 4 has been continued for the past few weeks. The No. 2 well is within 100 feet of the producing horizon and should be completed within the next few days. According to reports, it has been logging slightly lower, structurally, than the discovery well, but, regardless of the outcome, it has been an important test to determine westerly cross-section of the Leduc structure. No official reports have been made available of any tests made during the drilling of the well, but it is understood that promising oil and gas shows have been indicated in higher formations. Actual drilling operations have not been commenced by any of the other companies holding leases in the immediate area but it is expected that, when road bans are removed and equipment is assured, several wells will be commenced. Announcement has been made that Imperial Oil, Limited, will drill a well near Battle lake, about thirty-five miles southwest of the Leduc field. Location of the well has been made following an extensive seismograph survey of the area, with total depth of the test well expected to be in the 8,000- to 8,500-foot range. Drilling will be done with the heavy-duty rig last used at the De Winton test. Imperial Oil have abandoned hope of oil production in the Provost area after drilling nine wells, but will retain their interest in the gas field that has been developed. Of the wells drilled, four indicated gas flows ranging from 1,060 to 13,200 M.c.f. per day.

Jan 1, 1947

By E. H. Holm

"This paper is a market-oriented review of the industry's present and forecasted performance, considering some of the principal factors influencing natural resource development. The author illustrates the steady consumption growth of nickel, and stresses the need for a quantitative long-range approach to production, consumption and the supply/ demand balance on a worldwide basis. Objective consideration of this data exposes some popular misconceptions. The possibility of near-term undersupply of nickel is discussed in relation to historically rapid changes in inventories and demand patterns. What is the significance of the increasing reliance on lateritic sources? New• facilities, new processing methods and new product forms are illustrated as further evidence of the industry's determination to satisfy the needs and preferences of nickel consumers. Examples indicate how product forms must accommodate to fast-evolving end-use technology. A review of nickel's price performance is used as a base from which to explore tomorrow's price trends."

Jan 1, 1972

By P. M. STILES

Acquired in 1957, the limestone quarry of Ideal Basic Industries on Texada Island north of Vancouver has become a major supplier of high purity limestone and construction stone. Crushed limestone products are shipped by barge to various destinations along the B.C. and northern U.S. coasts.

Jan 1, 1984

By Karl J. C. Harries

"The following is an outline or check sheet of some things that might be looked at when considering the concept of a royalty or royalty provisions. It is not intended as a guide to what is right or wrong (that is for the parties to decide). It does not replace the discussions in this work and is not intended to be a complete or exhaustive compilation of matters to be considered. It presumes that you are familiar with the basic concepts of royalties and has been included as an aide memoire only. Use it as such, with caution and common sense, and amend it to suit your needs. Remember also that brevity can result in inaccuracy or imprecision. This is a danger in many points below.The section references are for the sections where the matter is the main subject of the section – see the index for other sections.Royalty TypesNet Proceeds [§§ 5.8.; 11.4.]• No accepted or understood meaning within industry.• Literal meaning, if not defined, would imply “net operating profit”.• Often defined as net profit with revenue base of proceeds from sale of product.• Should not be used without detailed and clear definition. Net Operating Profit [§§ 5.8.; 11.4. – referred to only]• Net profit without recoupment of pre-production expenditures.• Revenue base: usually proceeds from sale of product.• Operating costs deductible.• Some reserves may be permitted.• Recoupment of some post-production capital expenditures may be permitted.• Not often seen as basis for royalties in Canada."

Jan 1, 2003

By C. A. Godden, T. N. Atkinson

Metallographic techniques developed from studies of corrosion films and electroplated coatings on aluminum alloys, are discussed. These methods, the result of work at the Naval Research Establishment, give extremely flat fields at the interface despite the large difference in hardness, in cases where electrolytic polishing could not be used. Techniques to overcome the similarity in refractive index of immersion oil, aluminum ox1d~, and mounting plastic are also considered, as are methods for improving visual and photographic contrast in areas of interest. A device for marking specimens is also de-scribed. ELE•CTROLYTIC polishing is inapplicable in the study of surface films on aluminum, whether corrosion films or electrodeposits. Mechanical procedures must there-fore be followed. Sample flatness and edge retention are of paramount importance. Special measures are required in the study of oxide films, because of the close proximity of the refractive indices of aluminum oxide, mounting plastic, and immersion oil.

Jan 1, 1962