Search Documents

By Keith Jones, Largo Albert

"Decelerometer testing of a rigid guide system in a mine shaft pro vides usefuI information to operating and maintenance people. High acceleration/deceleration rates can lead to high maintenance costs to bath conveyances and shaft and can also present an operating risk . Possible disastrous results in the shaft have been avoided by restricting the maximum conveyance speed until the shaft and/ or conveyance problems have been solved.The test instrument is a valuable aid especially during commissioning or updating of a hoisting installation. High acceleration/deceleration rates also lead to reduced hoist rope life. During the past fourteen years, a total of 15,000,000 feet of testing was performed in 74 assorted shaft compartments.Based on this experience, it is possible to establish acceptable conveyance maximum speeds provided that all other conditions in the shaft compartment are normal. The body of the paper will present examples of several tests made under actual operating conditions.IntroductionMore and more mine operators are recognizing the real value in the use of the decelerometer for determining the state of shaft guide alignment in their shaft compartments , not only during the initial mine start-up periods, but also on a regular basis while the mine is in production.Decelerometer testing, is a technique in which an accelerometer , commonly known as a decelerometer, is used for measuring conveyance acceleration/deceleration in a lateral plane. lts purpose is to determine the severity of shock loads produced by misaligned shaft guides. Testing is performed by mounting the instrument on the conveyance and operating the conveyance (empty and loaded) at various speeds up to and including full speed . However, full speed may not be attained due to conditions indicated by the tests. These conditions may present an operating risk to the plant."

Jan 1, 1984

By Ayako Iwakoshi

Highly concentrated pastes of gold nanoparticles were successfully produced by use of a special kind of protective polymer and a mild reductant. Solid part of the pastes consists of up to 85wt% of gold nanoparticles, 10~30 nm in diameter, and residual protective polymer. This component can be diluted by any kinds of solvent at arbitrary rates. Electronics, optics, catalysts, colorants and surface metal coatings are possible application fields. 1. Introduction Noble metal nanoparticles are of interest in a variety of fields ? such as colorants, metal coatings, electronics(1), optics(2), and chemical catalysis(3). Especially, in the color field, the gold nanoparticle has been known as an aesthetic red colorant for stained glass and fine glassware, such as Venetian glass. The mechanism of coloring is attributed to surface plasmon absorption of gold nanoparticles(4,5). The gold nanoparticle in stained glass shows very clear red color, which is very durable for hundreds years. On the other hand, the red color of organic pigment in paint films often fades away within several years. We intended to reproduce the elegant and stable coloring of stained glass in paint films. In order to color a very thin, 20~50?m, paint film like stained glass, production of highly concentrated dispersion of gold nanoparticle is necessary. To achieve this, there were two issues to be overcome. One is how to prevent the coagulation of gold nanoparticles in highly concentrated solution. So far, several methods to prepare gold nanoparticles(6,7) were reported. But only a few methods succeeded to stabilize the gold nanoparticle dispersion at higher concentration than ppm order. The other is controlling of the particle size, this is because the color of gold nanoparticles is very sensitive to the particle size. Only when the particle size lies around 10 nm, the suspension exhibits red color like stained glass.

Oct 1, 2003

By V. Ogarlaci

Over 90% of the Romania's lignite reserve is located in the region of Oltenia, which is why this area is given special attention in the country's coal resources. Because the lignite deposit of Oltenia is comprised of 1-8 exploitable coal layers, their capitalizing calls for urgent arrangements to ensure rational exploitation under conditions of total safety, minimum losses and efficiency. The technology used the coal pits of North-Western Oltenia is the technology of excavation, transport and dumping in a continuous flow by using the complexes of excavation, transport and high-capacity dumping. The theme of this paper is of particular importance because the rhythmic operation in complete safety, is necessary both for sizing and keeping within the bounds of acceptable values, throughout the process of excavation of the geometric elements of the coal faces, marked by: the height of benches, slope angle and width of berms. Geometric dimensions of the benches of the open pits, the height of benches, slope angle and width of berms shall be calculated and shall be based on: the massif structure that forms the benches; physical-mechanical characteristics of rocks from the bench; working conditions, characterized mainly by mining and extraction methods applied; functional parameters of the mechanical equipment used to perform various operations on the coal face etc. For this study it was necessary a broad field for task tracking, measurement, research and design elements of the coal face, for land survey and a desk activity by: processing of topographic data, laboratory analyses on physical and mechanical properties of rocks and numerous specialized studies. In the final part, we bring some contributions to elucidating the issues of special importance for the lignite coal pits of Oltenia, coming up with data, graphics, formulas, solutions and concrete dimensioning of coal faces in terms of using technology in a continuous flow.

Aug 1, 2013

By H. Weissenbaeck, B. Nowak, M. Oesterreicher, R. Stastny

The producers of certain metals like nickel and cobalt increasingly face a shortage of easy-to-mine and easy-to-process ore bodies. Their focus is shifting towards alternative raw materials which in turn demand new, different extraction techniques. One potential route for processing a ferrous ore with a non-ferrous target metal is atmospheric leaching with hydrochloric acid followed by purification of the pregnant leach solution (PLS). For the separation of iron from the PLS, and, in turn, the extraction of the non-ferrous compounds, the following flow sheet is proposed. Pre-concentration of the PLS, oxidation of ferrous (if present) to ferric chloride, hydrolysis of ferric chloride leading to the precipitation of hematite and the evaporation of hydrochloric acid, followed by crystallization of non-hydrolysable metal chlorides by means of sparging hydrogen chloride into the solution. Hydrogen chloride required in the latter step is produced internally by super-azeotropic distillation of regenerated hydrochloric acid. The liquid filtrate from the crystallization step is recycled to hydrolysis. Depending on the specific composition of the PLS, the hematite produced contains only traces of other impurities, whereas the crystallized mix of non-hydrolysable metal chlorides – containing also the target metal in enriched form – contains ferric chloride only in an amount referring to the filter cake moisture. These crystals can then undergo further hydrometallurgical separation and extraction processes. As an example, this flow sheet is proposed for treating nickel laterite ores. Experiments related to the demonstration of crucial assumptions in the flow sheet are presented. Based on those experiments a mass and energy balance of the flow sheet was calculated and is presented here together with a table of the major consumables in order to provide a basis for an operating cost estimate and other process economics.

Jan 1, 2016

By Robert B. Parsons

"This article is based on a paper presented by Jim Scott at the 1988 annual convention of the Prospectors and Developers Association of Canada. The paper suggests a number of factors that might be taken into account in negotiating royalty terms.IntroductionRoyal ties are a part of mining life in Canada. They are used by many kinds of individuals in many kind s of situations. Prospectors commonly take royalty interests back when they transfer claims to development companies. Mining companies disposing of undeveloped (or sometimes even developed) properties are often paid at least in part by royalties. Royalties are even used by institutional investors with no other connection with the resource industry.Such different royalty holders have different investment goals, different cash flow requirements, and different risk / return preferences. These differences have given rise to a number of different royalty type s. These types range from the simplest cents-per-ton royalty (where the operator pays a royalty at a fixed rate per ton milled) to net smelter return or ""NSR"" royalties (where the royalty is based on a percentage of the operator's NSR) all the way to net profit interest or ""NPI"" royalties (where the royalty is based on the operator's bottom-line net profit),The fundamental difference between the many royalty types is in the risk/ return relationship. The cents-per-ton royalty, for example, is relatively risk-free. Of the many economic factors which affect a mine, the only one which will affect the royalty holder is the amount of ore physically milled. On the other hand, the potential for significant gains under a cents-per-ton royalty is also very limited. The royalty holder will not share in any increases in the market price of the end product or any cost reductions achieved by the producer."

Jan 1, 1988

By Robert B. Parsons

"This article is based on a paper presented by Jim Scott at the 1988 annual convention of the Prospectors and Developers Association of Canada. The paper suggests a number of factors that might be taken into account in negotiating royalty terms.IntroductionRoyal ties are a part of mining life in Canada. They are used by many kinds of individuals in many kind s of situations. Prospectors commonly take royalty interests back when they transfer claims to development companies. Mining companies disposing of undeveloped (or sometimes even developed) properties are often paid at least in part by royalties. Royalties are even used by institutional investors with no other connection with the resource industry.Such different royalty holders have different investment goals, different cash flow requirements, and different risk / return preferences. These differences have given rise to a number of different royalty types. These types range from the simplest cents-per-ton royalty (where the operator pays a royalty at a fixed rate per ton milled) to net smelter return or ""NSR"" royalties (where the royalty is based on a percentage of the operator's NSR) all the way to net profit interest or ""NPI"" royalties (where the royalty is based on the operator's bottom-line net profit),The fundamental difference between the many royalty types is in the risk / return relationship. The cents-per-ton royalty, for example, is relatively risk-free. Of the many economic factors which affect a mine, the only one which will affect the royalty holder is the amount of ore physically milled. On the other hand, the potential for significant gains under a cents-per-ton royalty is also very limited. The royalty holder will not share in any increases in the market price of the end product or any cost reductions achieved by the producer."

Jan 1, 1989

By Robert B. Parsons

"The mining industry is adjusting its sights to take a shot at the rising level of non-profit taxes which threaten to handicap the industry 's competitive advantage. In the case of this particular expedition, the industry evidentally has a strong ally - the country's mines ministers. It appears that an initiative is under way to assess the impact of non-profit taxes on mining in Canada as compared to other mining nations.IntroductionSeventy-five years ago, Canadians were unceremoniously introduced to something called income tax. Since then, income tax has been identified as the source of countless evils ranging from the common cold (attributed to stress) to the demise of the economy. Some years later, the provinces jumped on the bandwagon with their own income taxes, and later on with mining taxes. These profit-based taxes had some appeal to elected officials and to a segment of the populace. The onus of the taxes varied directly with the ability to pay (in theory, at least). Previously, the principal sources of government revenues had been property taxes and customs duties, which were viewed as possibly being somewhat regressive in nature.The mining industry has always had concerns about different aspects of income and mining taxes - the tax rate is too high or the depreciation rate is too low, and so on. Recently, though, the industry has turned its sights on the expanding array of taxes which are not based on profit, including payroll taxes, capital taxes, water taxes, sales taxes, fuel taxes, property taxes, environmental levies and user fees. The industry is seriously concerned that the rising level of non-pro fit-based taxes is not only hampering the industry 's ability to reinvest in Canada, but is also placing Canada at a disadvantage in terms of trying to attract new investment capital."

Jan 1, 1992

By Ron Jessulat

"IntroductionBrunswick Mining and Smelting Corp. Ltd. is a IO 500 tid base metal producer. Development is carried out by Jarvis Clark MJM-21 3-boom development jumbos, using Tamrock E400, 410 and 550 pneumatic drills. Typical drift size is 13 ft by 18 ft with a 12-ft advance per round. Blast holes are 1 ½ in. in diameter while reamed holes are 3 in. in diameter. AN/FO is the principal blasting agent, being loaded by C-I-L model60R intermediate loader. The detonators are NONELS and DETINELS. Sulphide dust explosions occur during blasting when dusts from certain minerals such as pyrite and pyrrhotite are ignited by name from the detonating shots. The result is a secondary unwanted explosion with a characteristic shock wave and name front that are very destructive to mine services such as ventilation ducting, electrical cable, and ventilation control doors.A typical reaction in the Brunswick orebody occurs according to the chemical formula:4FeS 2 + IIOs-2Fe2O3 + 8SO2 + 3458--(Enright , 1988)The hematite (FeO3) is deposited as a red dust in the blast area while the toxic sulphur dioxide gas (S00 contaminates the underground workings . The presence of S02 gas disrupts production until it is purged from the area by the mine ventilation system or dissipates slowly in those areas where the vent ducting has been melted by the name front or torn down by the shock wave.Sulphide dust explosions exact a high economic toll. Direct costs in damaged materials and wages are probably exceeded by the value of lost production and disruption to the mining cycle. In addition, the health and safety concerns associated with sulphide dust explosions cannot be ignored."

Jan 1, 1993

By Xu Feng, Han Shufeng, Zhu Bin, Wang Mingming

Due to urban subway tunnels mostly built in the cities with highly density buildings, the geological and construction conditions is complex, especially certain sections of the subway tunnel will pass through from the foundation of the overpass, therefore the stability and surface deformation control of that section’s tunnel excavation is particularly important. Taking Xi'an Metro Line Three interval tunnel as a research object, we have used FLAC3D simulation to analyze the tunnel’s surrounding soil deformation and tunnel lining stress distribution under bridge foundation with shallow buried covered excavation method. Analysis results show: (1) After the excavation of the tunnel right line, due to the bias of the upper bridge foundation the right of the tunnel showed relatively large deformation. In order to ensure the construction safety, we recommended using the grouting anchor reinforcement on the right side wall to further control the deformation zone. (2) The maximum vertical displacement of the ground occurred in the right wall of the tunnel portion which was due to the intensity of soil outside the grouting range of the arch is low, as a result the deformation is larger; this position requires special attention, strengthening the monitoring measurements of this part is necessary to avoid the large deformation and other adverse effects of the upper portion of bridge foundation. (3) The maximum vertical force area of the initial lining of the tunnel is in the middle of the side wall, while the second lining in this part of forces is smaller, thus at the beginning of the construction of the liner, attention should be paid to this area. On-site grouting or steel bracing reinforce support may be used if necessary.

Jan 1, 2015

By V. G. Papangelakis, G. P. Demopoulos

"Recovery of gold from refractory ores and concentrates presently constitutes one of the most important, challenging, and exciting areas of R&D activity in the gold processing industry. New technologies are being tested for the treatment of refractory gold materials, some of which have been advanced to the level of commercial operation. In this paper, some recent technological developments in the hydrometallurgical processing of pyritic matrix-refractory gold ores are highlighted. Key operational steps of each of the alternate hydrometallurgical technologies are analyzed and potential advantages and drawbacks are identified. The processes which are reviewed are: hydro chemical oxidation, biochemical oxidation and pressure oxidation. INTRODUCTIONOver the years the term ""refractory"" has been applied in gold ore processing to denote situations in which straightforward cyanidation failed to yield high gold recoveries. A number of mineralogical and chemical factors may be responsible for this ""refractoriness"" problem. A systematic classification of the different options for their treatment has been discussed in a recent review paper. In this paper, the pretreatment of the submicroscopic gold encapsulated within the matrix of pyrite and arsenopyrite minerals is considered. This type of gold is the ultimate refractory material because complete breakdown by reaction of the host mineral structure is required.The method which has been traditionally applied for the treatment of pyritic-type refractory gold ores is an oxidation roast (single stage or double stage depending on the As content) of a flotation concentrate to produce a porous calcine, the latter being more amenable to cyanidation. Despite its established practice, oxidation roasting is not considered particularly attractive with today's standards for high product recovery and clean environment. Roasting is known to be very sensitive to heating parameters and feed composition and deviation from optimum conditions can result in reduction in permeability which is translated to incomplete gold liberation."

Jan 1, 1989

By M. Pekguleryuz, S. A. Argyropoulos

"The recovery of additions in light metals is an important parameter influencing consistency of the finished product, which ultimately means cost. Recovery is a function of many parameters such as assimilation speed, addition density, addition practice, liquid metal processing conditions, etc. In liquid metal processing operations, it is desirable to have the maximum possible recovery at the shortest possible time.In this paper a new index will be presented, namely, the rate of recovery (RR). This index quantifies the addition recovery and introduces the time dimension in the recovery increase. As such, the RR equips the liquid metal practitioner with an accurate picture of addition assimilation in liquid metals. Results will be presented on how this index is applied to a variety of additions in liquid aluminum. IntroductionThe data on addition assimilation kinetics offer a valuable parameter describing how fast a given addition enters the metal bath. These data may be expressed as gr m-2 s-1 of additive for a set of experimental conditions which might include bath temperature and degree of bath agitation among others. However, the liquid metal processing practitioner is more interested in the recovery of additions. In other words, the point of interest is the percentage of the used addition entering the metal bath. Ideally, the addition recovery can reach the 100% level. However, in practice, the addition recovery never or rarely reaches that level. Many factors can contribute to this. Some of these factors can be slow assimilation kinetics, addition density, addition practice, turbulence of the melt, etc. In some cases, sloppy addition practices can contribute to low recoveries, or even worse, to erratic recoveries.In this paper a new parameter is introduced. This parameter relates the maximum addition recovery observed over the time needed to achieve this maximum recovery."

Jan 1, 2002

By G. R. MANSON

The Brisco Barite Mine lies 70 km south-southeast of Golden, British Columbia. Barile mineralization occurs in a northstriking brecciation zone within Ordovician-Silurian Beaver/ oot dolomites and quartzites. Brecciation was caused by faulting related to the Mount Forster-Steamboat Fault. The main barite vein occupies a fault zone and is up to 12 m wide and over 250 m long. It is light grey to white, fine grained and compact; BaSO4 content is 9/. 70 per cent. Production started in 1945 and has continued to the present. Barile originally was removed from an open pit; later, an adit, begun in 1957, reached more than 240 m along the vein, 15 m below the pit floor. Today ore is hoisted from a decline resting some 37 m below the pit floor.

Jan 1, 1984

By S. Tuttle, R. Sisson

"Suncor Energy Inc. has proposed a 2.2 billion dollar expansion to the current oil sands operation, which will more than double the productive capability of the facility. As part of the application for this expansion, a comprehensive closure plan had to be developed and filed.Closure planning includes a systematic evaluation of the area to be developed, the development activities planned, the goals and objectives of the corporation in re-establishing landforms and ecosystems at the same time as running an effective operation. As early as is practical during the mine development, surface contouring is completed, soil is reconstructed, and vegetation, surface drainage and wetlands are re-established. Once active reclamation is complete and vegetation has been re-established, Suncor monitors maturation of landscapes and ecosystems to provide the submission basis for reclamation certification"

Jan 1, 1999

The Cadia mine is shifting from the open pit operation to the Cadia East underground block cave. The resulting increase in milled tonnes and the decrease in fines production through shifting to block caving require an increase of over 25% in installed power. This expansion is being accomplished via the installation of up-front crushing and HPGR milling of the ore, with the SAG mill receiving a secondary crushed feed. This design, criteria and rationale for selection is presented. Over the coming years, the mine will further expand capacity. The target is to accomplish this with minimal addition of installed power or use of fresh water. This presents a challenge that epitomizes the future constraints on our resource dependent and intensive industry. The approach and proposed options to this longer-term expansion are also presented.

Jan 1, 2012

By G. R. Rawsthorne

"The Con-Rycon mine is located on the north shore of Great Slave Lake in the Northwest Territories within the present city limits of Yellow-knife. Development work on the Con property started in 1936, resulting in a mine-mill complex which produced its first gold brick on September 5, 1938. Since that date 5,000,000 tons of ore have been mined yielding 3,000,000 ounces of gold. At present there are 220 employees at the mine.MineThe mine has 1.22 miles of vertical shaft, 41 miles of level development and 10 miles of inclined raises. There has been 1,000,000 feet of diamond drilling in search of ore. The temperature at the 4900 level (4400 feet below sea level) is 68 deg. F.The present mining method is cut and fill. The majority of the ore mined today passed through an internal winze before reaching the main shaft. The long haulage and double handling will be eliminated with the completion of a new shaft presently under construction to the 5800 level.MineralizationThe ore treated today is from the Campbell shear 1vhich is characterized by lenses and veinlets of coarse textured quartz containing some carbonate, sulphides and finely disseminated as well as visible gold. At the lower levels of the mine the arsenopyrite content in the ore is de-creasing with a~ increase in the levels of chalcopyrite and pyrrhotite."

Jan 1, 1974

By P. W. Godbehere, B. W. Brooks

"This paper deals with the milling of slags from the Noranda Continuous Process, in the Horne Concentrator at Noranda, Quebec. The milling of copper slags, although novel in Canada, has been practiced in Japan, Finland and elsewhere for several years.In March 1973, the prototype Noranda Continuous Process furnace or ""reactor'' came on-stream, In this pyrometallurgical process (see Fig. 1), copper concentrates mixed with flux are smelted in a single furnace to form copper or a high grade copper matte, and slag. The conventional smelting processes of roasting, reverberatory smelting and converting have been incorporated in a single 17 ft. diameter by 70 ft. long steel cylindrical vessel (l, 2). The copper or matte is tapped from the bottom of the reactor into ladles and transferred to an anode furnace or to a converter. The slag is tapped into 40 ton capacity ladles, cooled, crushed, and conveyed to the concentrator. At the present time, the reactor is operated to produce matte. The matte slag* containing 4 - 6 per cent copper is milled using conventional ore dressing grinding and flotation equipment. A flotation concentrate assaying 35 - 40 per cent copper is recycled to the reactor. Crushing, conveying, grinding, flotation and tailing disposal equipment previously used for over 40 years for ore treatment has been modified to suit the requirements of slag milling. Slag milling is essentially the scavenger circuit of a pyrometallurgical process."

Jan 1, 1977

By R. W. Lawrence

"Biological leaching can be used to enhance the recovery of gold and silver from refractory ores, concentrates and tailings. The method liberates precious metals associated with sulphide minerals such as pyrite and arsenopyrite making them amenable to cyanidation. The chemistry and features of biological preoxidation leaching is discussed. A summary of the results obtained on various ores, concentrates and tailings is presented.INTRODUCTIONRefractory precious metal ores in which gold and silver are finely disseminated in sulphide minerals such as pyrite and arsenopyrite are becoming more important to the mining industry. This is due both to a depletion of simpler, free-milling ores and to a significant increase in the price of gold in recent years. Whereas many ores can be directly cyanided with gold solubilizations over 90% obtained, the refractory ores respond poorly to direct cyanidation and require decomposition of the precious metal-bearing sulphide minerals to increase recoveries.Decomposition of sulphides by oxidation prior to cyanidation can be carried out by several means. The oldest method is roasting which removes unwanted ore constituents by high temperature oxidation and volatilization. In Canada, for example, roasting is used at Giant Yellowknife (Connell and Cross, 1981). Another method gaining increasing acceptance is pressure hydrometallurgy which uses aqueous oxidation conducted at high temperature and pressure. Homestake Mining Company have recently completed construction of a plant incorporating pressure oxidation at their Mclaughlin property in California (Guinivire, 1984)."

Jan 1, 1985

By J. H. Nantel, J. F. Archibald

"The presence of radon from uranium-bearing ores, waste and from backfill material introduced underground to provide ground support, work platform and waste disposal functions, requires that ventilation controls be established to maintain safe working level concentrations. One approach has been developed at Queen's University to quantify radon and radon daughter source level s and to estimate ventilation requirements necessary to maintain these safe levels.Knowledge concerning the sources of radioactive contaminants and their production quantities is of value for planning and design stages of ventilation control systems. For any given mine layout, radiation level estimates may be forecast and modified by ventilation network design where excessive production quantities may exist.Behaviour of Radon Gas in MinesRadon gas, produced from the decay of Ra-226 in a host medium, will diffuse through porous media. In areas adjacent to mine workings, radon will be liberated into the mine atmosphere. The rate of radon emanation is proportional to the rate at which radon is produced within the host material (a function of the ore grade of U308) , to the radon concentration gradient in the host pores and to the diffusion properties of the material.The radon source concentration is determined by the rate at which Rn-222 is produced by the decay of Ra-226, and by the emanating coefficient (E), or fraction of the radon which escapes from the source matrix and is free to diffuse through the pore spaces."

Jan 1, 1984

By K. John

"THE most recent estimate of minteable coal reserves in Saskatchewan was made by the Federal Royal Commission on Coal (1944- 6). Saskatchewan was then estimated to have some 24 per cent of the Canadian reserves and two-thirds of this is located in what is called the Souris-Estevan area, which lies in the southeast corner of the Province and border's on the International boundary. It is also estimated that there are some 61/2 million thousand-tons in this area of lignite coal which grades 8,000 B.t.u. or less and has a moisture content ranging from 30 to 33 per cent. Ownership of coal rights in the Province is widely dispersed between the Crown, individuals, and corporations, and a recent survey disclosed that 40 percent of ownership was vested in the Crown and 60 per cent in private individuals and corporations. Coal rights on Crown lands may be leased at an annual rental of $ 1.00 an acre. Under such leases, a royalty of 5 cents a ton is levied on all coal mined. A royalty of 7 cents a ton is levied on coal produced from lands where mineral rights were purchased from the Federal Government prior to the transfer of jurisdiction over natural resources to the Province, in 1931. An annual mineral tax of 50 cents per acre has also been imposed by the Provincial Government on all coals within a defined producing areas."

Jan 1, 1952

By C. Larsen, E. Goodwin, E. Konigsmann

"This paper describes the development of an innovative effluent treatment process for cyanide and heavy metal removal from tailings wastewaters at Hemlo Gold Mines Inc. Golden Giant operation.The importance of minimizing dissolution of contaminants in the gold leaching circuit is discussed, as well as using recycled water in milling circuits to the fullest extent possible. Finally, a brief description of the role of natural cyanide degradation in the tailings pond is provided.Emphasis is placed on the need for overall water quality management to ensure minimum effluent treatment process costs and complexity while producing excellent quality effluents.1.0 INTRODUCTIONHemlo Gold Mines Inc. owns and operates its Golden Giant Mine located forty kilometres east of Marathon, Ontario. The Golden Giant mine is one of three gold operations exploiting the large gold orebody located in the Hemlo area. The milling facilities include two stage secondary crushing, three stage, closed circuit ball mill grinding with no reagents, thickening, cyanide leaching and carbon in pulp gold recovery unit operations. The average throughput is 3000 tonnes per day of 10 grammes per tonne gold ore. Figure 1.1 shows a schematic flowsheet of the operation."

Jan 1, 1989