Search Documents

By Kenneth M. Haley

THE development of Reserve Mining Company's pelletizing practices began in 1949 in a pilot plant located at Ashland, Kentucky. Three years later the participating companies -Armco Steel Corporation, Cleveland Cliffs Iron Mining Company and Republic Steel Corporation concluded the work and the small plant was shut down. Oglebay Norton and Company was the operating manager and Armco Steel Corporation furnished labor and services. Arthur G. McKee and Company were the designers and constructors. The equipment flow sheet that was employed in that pilot operation is shown in Figure 1. This was Reserve's first step from the laboratory work per-formed by the Mines Experiment Station of the University of Minnesota in developing a commercial operation. The plant used New York state concentrate, purchased from Jones and Laughlin Steel Corporation's Benson Mine. This concentrate, minus 14 mesh, 64.3 per cent Fe, 5.7 per cent Si02, was processed at Ashland to 80 per cent minus 325 mesh in conventional ball mill, classifier, thickener, filtering

Jan 1, 1961

By G. M. Ritcey

The recovery of copper from low-grade solutions res ulting from dump leaching is well known, whereas the recovery from highly concentrated copper solutions has not been practiced. This paper discusses the use of Ashland Chemical's Kelex 100, a substituted quinoline, for the recovery of copper from solutions resulting from leaching copper-nickel concentrates. A flow sheet is described, and an economic comparison shows Kelex 100 to be superior to either the LIX 64N or LIX 70 reagents of General Mills for the recovery of copper.

Jan 1, 1973

By Paul Guliov

Potash dominates the industrial mineral scene in Saskatchewan accounting for 44% of total provincial mineral production in 1981. More than 7 million tonnes of potash have been produced annualy in recent years; ten underground mines are presently (1983) active. Sodium sulphate and cement are also important mineral products. Construction aggregates, clay products, bentonite, salt, peat moss and sulphur complete the list of industrial mineral products.

Jan 1, 1984

By Jean-Christophe Ehrström, Fanny Mas

"A specific test set-up has been developed to study at the lab-scale the high-temperature behavior of aluminium alloys in conditions close to those experienced by thick plates during hot-rolling. A particular attention is paid to reproducing both the stress triaxiality and strain fields that exist in plate during rolling. In addition to standard ductility measurements by means of secondary tensile tests (STT), multi-step plane strain compression (PSC) tests have been performed to mimic hot-rolling pass schedules. Tool and sample geometries were adapted to allow low h/a ratios (h= average specimen thickness, a= tool width) and thus guarantee depressive stress conditions at the center of the specimen during most of the test. Such conditions resulting in porosity opening can then be used to investigate the impact of rolling conditions on damage evolution. The mechanical testing was combined with post-mortem high-resolution ultrasonic scans allowing to detect small amounts of damage and quantify its evolution as a function of processing parameters such as strain and temperature. The test set-up was validated on two 2050-type AlCuLi alloys with different susceptibilities to high temperature embrittlement.INTRODUCTION Aluminium thick plates are widely used in the aerospace industry, mainly as semi-products to be machined for internal structure parts of wings (spars, ribs) and fuselage (frame). The conversion route of such products always involves a hot-rolling step, the conditions of which (temperature, speed, pass schedule) have to be optimized to maximize both mechanical properties and final plate quality. This goal cannot always be efficiently achieved by full-scale industrial trials as (a) cost limits the number of possible test conditions and (b) it is often difficult to change one parameter alone. That is why there is a need for laboratory-scale tests able to mimic the rolling process in terms of temperature, strain rate, stress triaxiality and deformation. Most laboratory hot-rolling mills do not adequately simulate industrial processing routes, especially in terms of heat loss, deformation speed and rolling geometry (maximum roll gap vs. work roll diameter). Concerning thick plate, it is of interest to achieve both similar deformation and L/h ratio (L=arc of contact, h=mean gauge) per pass as the industrial schedule because they are simultaneously involved in damage evolution and void closure during hot forming processes (Saby, 2014)."

Jan 1, 2018

By Per Hedvall, Jan-Eric Ståhl

"The main objective of this study is to introduce the new Sandvik’s production cost-model within Crushing & Screening (C&S) technology. So far, there have been different ways of determining different production costs in the industry, however, the previously published and presented methods have not been very efficient in calculating the costs per product and metric ton. Accordingly, the current study has been planned and started in collaboration with Lund University to provide an accurate and easy to implement cost estimation program to determine the costs for crushing and screening plants worldwide.The proposed model has been adapted to fit the C&S processes of different rocks/ores fractions. The result is presented as cost per ton of the end product(s).Within this paper the cost estimation results for 3 different crushing and screening plants are presented based on the information obtained from the following sources: a) documents at Sandvik SRP, b) Sandvik’s crushing & screening internal/external machines/plants data and information, c) literature studies, including the use of Sandvik’s internal/external simulation and software programs, d), visiting the crushing and screening plants ,e) interviews, information systems’ data, and, f) testing and observations by ourselves.In order to improve the level of accuracy and the validity of the attained results, simplistic Monte-Carlo simulations have been used, where needed. The achieved results, so far, have proven the reliability of the model. The calculated cost estimations have shown an accuracy over 80% when they compared with real cost data obtained from plant practices.The current cost calculation model, will offer the possibility of:•,Calculating the production costs in proposed and/or existing C&S plant.•,Making detailed cost analyses for the end product(s) in proposed and/or existing C&S plants.•,Determining the profitability of each finished product when it’s required.•,Cost optimization by potentially cutting the cost for part of C&S plant with an existing plant practice"

Jan 1, 2016

By The Staff

"THE property of Red Mountain Mines Limited is located 11/2 miles north and west of the town of Rossland, in southern British Columbia. The mine is situated on the flank of Red mountain, famous in pioneer days as the site of a number of profitable gold-copper producers. Mining and milling commenced in May, 1966, and by the first of July the concentrator was treating close to its average design capacity of 400 tons per day. The following description of the property and its operations is divided into three parts, dealing respectively with geology, mining and milling.GeologyAll the known ore reserves of Red Mountain Mines occur on the Coxey claim, on the west slope of Red mountain. Although there are indications of molybdenite mineralization elsewhere on the Company's property, these have not been developed.The Coxey and adjoining areas are underlain by the Mount Roberts formation of the Rossland volca-nics. This formation consists of an interbedded series of volcanic and sedimentary rocks, mostly brecciated and silicified near the ore zone, and all intruded by igneous rocks which occur in various forms, and vary in composition from basic to acid. The country rock in the vicinity of the mineralization seems to be mostly a volcanic, approximately andesitic in composition, and possibly a surface flow. There is much banding, some of which is undoubtedly due to tuff and agglomerate layers, and some to narrow, siliceous, sedimentary horizons such as the surface exposure of the main ""A"" orebody, much of which was a thin capping of greyish banded rock that looked like quartzite. The drill holes also intersected occasional layers of black, argillaceous quartzite, sometimes altered to a greenish colour. The whole assemblage has been silicified with varied intensity, sometimes to such an extent as to have obscured or obliterated the original characteristics. The mineralized zone has also been strongly brecciated, the fragments varying in size from less than an inch up to large masses, best described as a mega-breccia. Anomalous results obtained in drilling, such as sedimentary sections that do not appear in adjoining holes, may sometimes be due to the presence of these large blocks, no longer in their original position. The whole volcanic unit is thus very complex and confusing. For practical purposes, the ore may be said to occur in a greenstone formation with minor sedimentary interbeds and considerable later igneous material."

Jan 1, 1967

By R. B. Nourse, S. F. Gwynn-Jones, S. Nikolic, M. L. Bakker, I. McDougall, H. Joubert

"Tenova Pyromet’s core furnace knowhow and expertise has been built within the ferroalloy and nickel/platinum group metal (PGM) industries with the supply of electric furnaces for a number of nickel/PGM operators, including Eastplats, Lonmin, and Anglo-Platinum in South Africa, Mineraçào Serra Da Fortaleza in Brazil, and Norilsk Nickel in Russia. Tenova Pyromet has also supplied the electrode columns and associated electrode equipment – the heart of the electric furnace technology – for cobalt recovery in furnaces in Zambia and the Democratic Republic of the Congo. The quantity and size of projects undertaken by Tenova Pyromet has provided the opportunity to continuously improve furnace designs and the scope of supply, culminating in the most recent nickel/PGM project currently under construction at Northam Platinum. Through this innovative culture, the Tenova Pyromet Base Metals Initiative was formed in 2015 to develop the Novasmelt™ Furnace; a next generation optimised Top Submerged Lance (TSL) furnace design. The combination of Tenova Pyromet’s advanced Novasmelt™ product with our industry leading electric furnace technology are discussed with reference to applications for nickel and cobalt production. Flowsheet arrangements are compared summarising potential capital savings, operating requirements and achievement of downstream product quality.INTRODUCTION Tenova Pyromet is a leading player in the field of smelting technology development and equipment supply. Tenova Pyromet is the result of the union of three furnace suppliers under the Tenova banner: Techint Technologies (Tagliaferri), Core Furnace Systems Corp (Lectromelt) and Pyromet Technologies. The furnace experience of the combined groups dates back over a century with the earliest Lectromelt going into production in the early 1900s. Throughout the modern era, Tenova Pyromet has developed a reputation for providing dependable innovative smelting technology, high quality equipment and sound project execution to a worldwide client base with customer plants operating in Europe, Southern Africa, North America, South America, Russia, Kazakhstan, the Middle East, South Korea, and India. Tenova Pyromet’s core knowledge and expertise was developed in the South African ferroalloy, base metals, and platinum group metals (PGM) smelting industries. Tenova Pyromet has spent considerable effort on development and has contributed significantly to improve the state of the smelting industry. Tenova Pyromet’s electrode columns have become widely renowned and are now providing significant benefits, especially in increased furnace availability, to many smelting furnace operators. The electrode column is the heart of the furnace as it delivers a controlled amount of electrical energy, at an optimum depth in the burden/bath, to the smelting process. Every furnace is custom designed to the specific operating range and optimal operating point of that furnace and process"

Jan 1, 2017

By G. Forté, R. Girard

The Alcan Bayer Process Experimental Centre (BEC) is an essential development tool for the Bauxite & Alumina researchers at the Alcan Arvida Research and Development Centre in Jonquiere, Quebec. Between the laboratory tests and the industrial prototypes or the industrial applications, the BEC is a key element for technology transfers. The Bayer process is the extraction of aluminium oxide (or alumina) from the bauxite ore. The Bayer Experimental Centre's history and flowsheet are presented. The major pieces of equipment are described. Safety and design considerations are presented. Finally, examples of applications, double digestion and pressure decantation, are briefly described.

Jan 1, 2004

By K. Liu

"In the present work, two-step heat treatments with preheating treatments at different temperatures (175, 250 and 330°C) as the first step followed by the peak precipitation treatment (375°C/48h) as the second step have been performed in Al-Mn-Mg 3004 alloys to study their effects on the formation of dispersoids and evolution of elevated-temperature strength and creep resistance. During the two-step heat treatments, the microhardness is gradually increasing with increasing time until to a plateau after 24 hours when first-treated at 250°C and 330°C while there is a minor decrease with time at 175°C. Results show that both the yield strength and creep resistance at 300°C reach the peak values after the two-step treatment of 250°C/24h+375°C/48h. The formation of dispersoids is greatly related to the type and size of pre-existing Mg2Si precipitated during the preheating treatments, in which that coarsened rod-like ß’-Mg2Si strongly promotes the nucleation of dispersoids while finer needle-like ß’’-Mg2Si has less influence. Under optimized two-step heat treatments and modified alloying elements, the yield strength at 300°C can reach as high as 97 MPa with the minimum creep rate of 2.2×10-9 s-1 at 300°C in Al-Mn-Mg 3004 alloys, enabling them as one promising candidate in lightweight aluminum alloys for elevated-temperature applications.INTRODUCTION Due to the rapid demand from weight-sensitive automotive and aerospace industrials for the light alloys, such as aluminum alloy on the elevated-temperature applications, Al-Mn 3xxx alloys has been developed to obtain the good properties at both room temperature (RT) and elevated temperature, in which the dispersoid-strengthening mechanism plays a significant role (Li & Arnberg, 2003; Li, Muggerud, Olsen & Furu, 2012; Liu & Chen, 2015, 2015). In our previous works (Liu & Chen, 2015, 2015; Liu, Ma & Chen, 2017), the yield strength and creep resistance at 300°C of Al-Mn-Mg 3004 alloy were further improved by modifying the alloying elements, such as Fe and Mo, to optimize the characters of dispersoids, including the size, distribution and the dispersoids free zone (DFZ). For instance, Mo was introduced in aluminum alloy to further improve the volume fraction of dispersoids and reduce the area of DFZ, leading to increasing on both the strength and creep resistance at 300°C (Liu, Ma & Chen, 2017). On the other hand, the mechanical properties became worse at higher Fe content due to its consumption more Mn to form Al6(MnFe) intermetallics, resulting in less available soluted Mn for the precipitation of dispersoids (Liu & Chen, 2015). Therefore, optimizing the characters of dispersoids is always the key to improve the elevated-temperature properties of dispersoid-strengthened aluminum alloys for elevated-temperature applications."

Jan 1, 2017

By Nirmal Weerasekara

Mill liners serve the dual purpose of protecting the shell from wear and transferring the rotary motion of the mill to an effective grinding action. As the liners wear, the efficiency of energy transfer changes, so there is balance between liner profile for wear and for milling efficiency. A tool that can simultaneously predict the evolution of the liner profile and the associated change in milling efficiency should prove most useful in optimal liner design. This paper presents such an approach, based on measured 3D liner profile data informing 3D DEM simulations of charge motion and liner wear modelling.

Jan 1, 2012

By T. Gerritsen, C. Martinez, F. Stober, T Ma, J. R. Frias, M. Sedighy, J. Janzen

Electrode control systems regulate power by physically positioning electrodes. Due to the weight and inertia of the electrodes and hoist equipment, this is a relatively slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +/- 20% or more around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicana's laterite nickel furnace, yielding excellent results with a 3 to 1 reduction in power fluctuations.

Jan 1, 2005

By A. Villanueva

The effect of High Pressure Grinding Rolls (HPGR), as a preceding stage to a conventional ball mill circuit at PT Freeport Indonesia?s C1/C2 concentrators, has been studied in terms of downstream grinding efficiency and circuit performance. When milling the product from the HPGR, mill capacity increased by 21% for the same product grind size, when compared to processing similar ore from a conventional crushing circuit. This achievement is a result of several reasons, among them: reduction in feed size (F80), fines generation beyond the proportional reduction in F80, reduction in ore hardness induced by HPGR comminution mechanism, optimization of the recycle system of the HPGR and ball string optimization in the ball mill circuit given the new feed to the mill.

Jan 1, 2012

By S. H. Seyedein

A mathematical model was developed to study fluid flow and solidification in a single-roll casting system. Fluid flow coupled with energy equations were solved numerically using a finite volume method. A body-fitted coordinate transformation technique was adopted to handle the irregularly shaped domain. In order to couple the continuity and momentum equations, a SIMPLEC algorithm was used. A fixed-grid enthalpy method was considered to model the solidification in the system. The turbulence effect on flow field was modeled using a low-Re k-e model The model developed in this work was further run under various conditions to optimize the operating parameters of the process.

Jan 1, 2004

By A D. Turnbull

In Canada, although some research on extraction metallurgy is carried out by the universities and by government, the primary responsibility for the research necessary to the mining industry rests on the industry it-self. Automation is coming more slowly to the mining industry than to others, partly because of the problems of instrumentation. Operations research methods are, however, coming into use. Some new developments in the extraction of aluminum, in iron and steel, in pyrometallurgy and in pressure leaching of nickel, copper, zinc and lead are briefly outlined. Mention is made of uranium and the reactive metals. The importance of the by-product metals, notably antimony, bismuth, gallium, germanium, indium and tellurium, in the development of the electronics industry is also mentioned. The trend toward co-operative research by groups of producers, to develop markets for their products, is noted. In conclusion, there are a greater number of trained scientists, as well as larger amounts of scientific knowledge, available to the mineral industry than ever before, and, if properly used, this will result in great benefits to the industry and to Canada.

Jan 1, 1963

By D. M. Muir

Many plants produce iron(II)/(III) waste liquors which must be treated by neutralisation and precipitation to remove the iron. Iron can be precipitated as crystalline goethite or jarosite by controlled oxidation at low pH and as magnetite by controlled oxidation at high pH, but only at elevated temperatures (>70°C). This study focuses on the characterisation and settling properties of the iron oxides produced at ambient temperatures using various neutralising agents in order to improve the performance of thickeners. It was found that two-stage addition of caustic to FeC12 solutions produced a fast settling material characterised by Mossbauer spectroscopy and XRD as maghemite and magnetite. However, lime and magnesia additions resulted in more ferrihydrite formation and much lower settling rates because of the enhanced oxidation of Fe(II) by air. Settling rates decreased significantly as the proportion of Fe(III) to Fe(II) in the liquor increased. The mechanism of iron oxide precipitation is discussed together with some reasons for the different behaviour of the neutralising agents.

Jan 1, 2006

By H. C. Gunning

In spite of the fact that mining has been more or less active in the northern part of Vancouver island since the late 'nineties', there seems to be a remarkable lack of information regarding the nature and development of the region. Recently the operations at the Old Sport mine of the Coast Copper Company, Limited, and spectacular copper discoveries in the vicinity of Nimpkish lake, have directed the attention of the mining fraternity to the district. The writer spent the summer of 1929 making a reconnaissance examination of the general geology and mining properties of the area between Quatsino sound and Nimpkish lake, and he feels that a short paper describing the nature and mining possibilities of the region should be of interest at this time. A more detailed account of the ?geology and of the mining properties will be published in the forth- coming Summary Report of the Geological Survey. A short paper dealing with the Nimpkish Lake district was presented at the Annual Meeting of the British Columbia Division, held recently in Vancouver.

Jan 1, 1930

By J. P. Nicoud

"The Frog's Leg project is located in the Kundana mining centre 22 kms West of Kalgoorlie, in Western Australia. The Mines and Resources Australia (MRA) Dioro Exploration Joint Venture has had considerable exploration success centred on the high grade Frog's Leg discovery. A gold resource of 930,000 ounces has been defined. At Frog's Leg there have been three discrete resource domains recognised - Supergene, Contact, and Quartz Lodes. This paper describes the metallurgical test work undertaken.The selection of the drill core was a joint effort by the MRA Senior Geologist and Mineral Engineering Technical Services (METS) to ensure the samples were representative of the ore body. Optimisation of gold recovery was essential as both the Contact and Quartz Lodes have exceptionally high percentages of free gold as well as significantly higher grades than the typical open pit ores found in Western Australia. The metallurgical scope of work included documenting all of the metallurgical test results, establishing the comminution characteristics, determining the percentage of gravity recoverable gold, evaluating the cyanide leach characteristics and determining the tailings characteristics. These studies were used as the basis of flow sheet design to treat both ores and to discuss the advantages and disadvantages of alternative flowsheets. Investigations also included toll milling options at various plants as well as second hand and transportable plants. Considerable technical effort has been put into ore characterisation by way of test work aimed at managing the process risk at each stage of project development, including mitigation. MRA also carried out detailed mineralogical analysis of the ores."

Jan 1, 2005

By Northeastern University, B. Y. Cui, B. Y. Wang, D. Z. Wei, W. G. Liu, Z. C. Guan, S. L. Gao

To recover iron values from low grade ores by reverse froth flotation method, further research on cationic collectors used in reverse flotation of iron ores is launched to promote the utilization efficiency of iron ores. In this paper, one new cationic surfactant, bis(2-hydroxylethyl) dodecylamine (BHD), that could be dissolved in water easily was used as collector for quartz flotation. Flotation results indicated that BHD shows stronger collecting performance on quartz than hematite. The maximum recovery of 96.30% to quartz is obtained at a collector concentration of 20.0 mg/L in the pulp pH range from 5 to 7. This collector can be used to float quartz from hematite. And optimal separation results with 86.59% iron recovery and 66.60% iron grade to synthetic sample were achieved at a collector concentration of 20.0 mg/L and pulp pH of 5.02 when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by XPS analysis, infrared spectroscopic analysis and zeta-potential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occur between collector and quartz surface.

Jan 1, 2016

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential ?nanciers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory under-ground development is required to de?ne measured resources. The de?nition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and speci?c gravity are common. Veins may be composite, with ore-grade mineralization restricted to a speci?c structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and re?ect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature;(2) estimation of tonnage and grade, and (3) the presentation of this information using a classi?cation that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the dif?culties in applying geo-statistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or under-estimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for pro?t and/or greater economies of scale. De?nition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than ?nding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Abstract-Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential financiers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory underground development is required to define measured resources. The definition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and specific gravity are common. Veins may be composite, with ore-grade mineralization restricted to a specific structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and reflect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature; (2) estimation of tonnage and grade, and (3) the presentation of this information using a classification that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the difficulties in applying geostatistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or underestimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for profit and/or greater economies of scale. Definition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than finding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997