Search Documents

By Q. Dong, S. A. Nightingale

An investigation has been carried out to assess the effects of an applied voltage on the dissolution rate of MgO refractory in a steelmaking like slag. In this study corrosion results obtained from dip tests using a dense direct bonded MgO refractory in a CaO-SiO2-Fe2O3-FeO-MgO slag are presented. These results demonstrate that the application of a voltage across a dense MgO refractory-slag interface can change the rate of refractory dissolution. For the slag composition used and the voltage range tested, it was found that a maximum corrosion rate was obtained at a voltage setting of -0.45V. The results of this investigation have been explained in terms of voltage affects on Marangoni (interfacial tension induced) stirring and its effect on the MgO dissolution reaction that is at least partly controlled by mass transfer in the slag.

Jan 1, 2004

By S. Afshar, C. Allaire

Several studied have recently shown that the use of non-wetting additives is not always a sufficient solution to improve the corrosion resistance of refractories against molten aluminum. Once in contact with liquid aluminum, the coarse aluminosilicate aggregates, which do not benefit from the protective effect of non-wetting additives in the matrix, may be corroded. In some cases, the corrosion of aggregates, especially those containing a significant amount of free silica and/or alkalis, promotes corrosion in the surrounding matrix. The present work explores the possibility to protect the poor corrosion resistant aggregates via a lining procedure. A slip casting method, using either alumina or celsian-like composition based slurries, has been applied for lining of a series of aggregates. The results from this study show that such linings may prevent efficiently the corrosion of aluminosilicate aggregates. This work also analyzes the effects of firing temperature and lining quality on the corrosion behavior of aggregates

Jan 1, 2004

By B. T. Lu, J. L. Luo, T. Yu, C. W. Chen

In this paper, the synergism in erosion-corrosion process occurring in oil sand wastewater transportation caused by the interaction of mechanical and electrochemical factors was experimentally investigated. The erosion-corrosion tests were conducted with A1045 steel in synthetic slurries comprising tap water and silica sand. The material loss due to corrosion-enhanced erosion was assessed with the chemo-mechanical model developed by the authors recently. The results indicate that the material loss produced by corrosion-enhanced erosion at the open circuit potential can be formulated as a linear function of logarithm of corrosion current density. The wastage caused by the erosion-enhanced corrosion was analyzed based on the concept of non-equilibrium thermodynamics. The material loss induced by the erosion-enhanced corrosion is approximately a linear function of overall erosion rate measured in synthetic slurries, indicating that erosion-enhanced corrosion could be reduced by adopting surface strengthening techniques to improve the resistance to the plastic deformation in surface layer.

Jan 1, 2004

By Steven Aiken

The East Boulder Mine located in Montana, U.S.A. utilizes snowmaking to assist with mine water treatment for nitrogen removal. Nitrogen species, including ammonia, are common contaminants in mine water from underground mining operations. Snowmaking provides secondary treatment of nitrogen during the winter due to the chemical and physical processes that occur during snowmaking, in the snow pack and in the snowmelt. The primary processes include atomization, evaporation, sublimation and volatilization. The snowmakers also provide secondary treatment for nitrogen removal when used as evaporators and/or land application units during the summer. In 2002, the snowmaking process was successful at reducing total nitrogen in the mine water by up to 87%. If additional losses due to soil and root zone processes are included, total nitrogen reduction would increase to between 87 and 97%. Snowmaking is an effective nitrogen reducing treatment method during the winter when other treatment methods such as land application cannot be used.

May 1, 2004

By D. D. Rodier

The mining and metals indusrty's approach to Sustainable Development has dramatically evolved in response to growing concerns for the future ability of the industry to continue as a vital contributor to the sustainability of society. This paper will review recent trends,including the overriding global issues impacting the sustainability of society and what the Global responses to these issues have been. This will be followed by the response of the mining and metals industry to better contribute to sustainable development, starting with the landmark independent study the MMSD Study and the creation of a global policy voice for the industry, the Intrenational Council for Mining and Metals (ICMM). The tenants of the ICMM's Sustainability Framework guide this organization's work with the overall themes of performance improvement, leadership and leverage through partnerships. The paper will then conclude with a brief description of an example of what, an individual company, a service provider to the industry, is doing to assist in the industry's efforts.

Jan 1, 2007

By W. D. Gould, F. Goodazi, W. F. A. Duncan, A. G. Mattes

A biological treatment system designed to passively remove high concentrations of metals from leachate collected from a landfill near a large integrated zinc lead smelter has been in operation intermittently for the past five years including winter time operations. High metal removal efficiencies in the system were achieved. After 729 days of operation and treating over 8 million L of water the original anaerobic bioreactor constructed in 1997 was taken apart and rebuilt. The deconstruction of the bioreactor allowed systematic sampling at all depths of the biological matrix. Samples were analyzed for metal, S and TOC concentrations; as well bacterial populations were determined. Results of this sampling procedure are examined and compared at various depths within layers and between layers using one-way ANOVA and linear regressions. Metal concentrations were positively correlated with sulphur and negatively with total organic carbon. This is in concurrence with a model of biogenic precipitation of metal sulphides.

Jan 1, 2004

By G. Dörsam, M. Spreij, S. J. Van der Wal, A. P. Schmidt

The transfer of hot metal desulphurising from the torpedo cars to the hot metal ladles at the IJmuiden BOS plant no.2 caused a decrease in ladle lining life from 680 to 470 heats. Changing the desulphurising agent CaC2 for CaO during a trial period, for environmental reasons, led to a further decrease in refractory life. Availability of the ladles became critical and the major reasons for the low life were identified. Solving one of them, temperature, quickly resulted in restoration of the original lives. However, re- introduction of the new desulphurising agent on 50% of the heats again resulted in a decrease, this time from 700 to 550 heats. In order to be prepared for the full introduction of the new agent, thorough investigation of worn linings was conducted, revealing the major (chemical) wear mechanisms. With these findings, a new design for the hot metal ladle is proposed.

Jan 1, 2004

By Chelto. D. Smith

With the pressure on mine and metallurgical managers to take accountability for responsible corporate governance in their operational area, it is no longer acceptable to rely on central departments in the organization to manage safety, health and environmental impacts of the company?s processes. Environmental impacts exist because of the production or mining process. Some of the inputs to the process are natural resources and some of the outputs of the process are the inputs to the environmental control equipment, plant and the environment itself. Environmental management therefore needs to be incorporated in production management to effectively control and reduce the impacts. Many aspects of environmental management are identical to production management and the systems to manage them will likewise be very similar. By examining key components of these two management systems a decision can be made whether environmental management and production management are structurally similar and can be integrated into a combined IT solution.

May 1, 2009

By Jörgen Appelgren

Atlas Copco, a leading supplier of equipment and services to the mining and construction industries, is consistently pursuing its strategy to offer the most productive and economical solutions by continuously offering new innovative products. These are in most cases developed and tested in close cooperation with demanding end users before being officially launched on the international market. The demands for higher productivity and improved overall economy have resulted in systems for automation of the drilling cycle and also tools for integrating the Drilling equipment to the production control system used by the customer. In terms of improving the blasted material quality, Atlas Copco has placed emphasis on hole straightness and the need for hole logging and positioning. By applying state of the art technology to today?s computerized drilling rigs, major steps in improving overall drilling and blasting performance have been achieved. This paper will give some examples derived from the latest development of solutions for the Rotary drilling product line.

Oct 1, 2009

By Ross Dimmock

The productivity of a mine has the same goals as the quest to complete a tunnel project both safely and within time. A key aspect to achieving this goal is to excavate and support the working face as quickly as possible, allowing early re-entry to start construction of the next advance in safety. As with tunnels, the use of high performance wet-mix sprayed concrete has increased in mines dramatically over the last few years, and year on year has seen a stepwise increase in shotcrete performance, particularly in the first few hours. Shotcrete early age strength development clearly offers mining teams enormous advantages by allowing early, safe re-entry to the face. This paper illustrates that in the hard rock tunnelling field, modern shotcrete approaches do not cause delays in re-entry, but allow a continuous construction cycle. Furthermore, the paper identifies the most suitable, up-to-date shotcrete admixture and equipment technology available to the mining community to permit early re-entry.

May 1, 2003

By F. Shi

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT’s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By Wei Yun-Jie

Columnar jointed basalt is a fractured rock, with a lot of small spacing structural planes and poor integrity of the rock mass. On the basis of the comprehensive study of the columnar shape of Columnar joints, rugosity of the fracture surface and the chemical composition of basalt, columnar joints of Bai hetan dam area were formed as a result of the cooling and shrinkage effect of magma. Columnar joints basalt are mainly chlorite, kaolinite, epidote, tremolite chemical reactions and the content of columnar joints are mainly chlorite by slice identification and chemical analysis. Columnar joints basalt showed high uniaxial tension test, low coefficient of friction and high cohesion by indoor physical and mechanical test. Columnar joints rock mass showed high strength and large deformation by field shear test and deformation test. Columnar joints basalt can be used directly as a foundation of dam as long as we follow the rules and reduce disturbance strictly.

May 1, 2009

By Cheryl L. Allen

Increasing energy costs associated with mining have become an issue that must be addressed by industry to ensure sustainable production. As underground mine ventilation systems account for 40% to 50% of a mine?s total energy requirement, initiatives to maximize their efficiency have been introduced worldwide. A control method known as Ventilation-On-Demand (VOD), which adjusts the ventilation system by responding to the activities of mine personnel and air quality, has been commissioned at Vale?s Coleman Mine. This initiative is an effort to reduce energy consumption, maximize efficiency of the ventilation system while ensuring air quality. There are five control strategies that can be executed with the VOD control system in place at Coleman Mine: Manual real time control Time-of-Day Scheduling Event-based control Environmental control Activity Based Control/Tagging This paper describes the system, control strategies and impact on energy consumption and flexibility of airflow distribution as applied at Vale?s Coleman Mine.

May 1, 2011

By A. J. Antony Chettupuzha

Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project as well as model project processes. Much of the information relating to processes and their structure, the actors that operate them, and the data associated with each instance of a process is encapsulated within workflows. The wealth of information contained in an EPPM system can be exploited to extract knowledge that can provide significant cost benefits to construction companies. Workflows provide an ideal medium for the capture of knowledge over the course of a project lifecycle. We demonstrate how this knowledge may then be used to analyze workflows and determine metrics that establish the suitability of workflows to construction processes. We present a conceptual approach to measure the performance of a workflow, its constituent components and evolution, which may be used to lay the foundation for establishing paragon workflows suited to classes of construction activities.

Aug 1, 2013

By Craig Faulkner

Discharge cones for large Semi Autogenous Grinding (SAG) and Autogenous Grinding (AG) mills are subjected to high wear as significant volumes of ground ore and slurry exit the mill. With the larger diameter mills of 32ft to 40ft in size becoming the norm, very high, concentrated wear is highlighting the limitations of conventional discharge cones and frequent changes are subsequently required. This paper outlines the advances made in the design of the Bullnose discharge cone. Superior wear materials to increase wear life over conventional rubber or chrome-moly steel discharge cones and the introduction of key design features to reduce reline times and improve fit and safety during installation, offer significant opportunities for the mill operator. Collated from multiple case studies, the wear data and reline history from 2004 to present clearly illustrate the way in which superior component longevity has reduced the frequency of relines over the life of the product to increase mill availability and effectively increase the tonnes milled in a period.

Jan 1, 2012

By Yan Qun, Chen Xiao-ming, Ma Pei-long, Luo Xian-ping, Luo Cai-gui, Feng Bo

The effect of leach promoting reagent LPF on the leaching process of a weathered crust elution-deposited rare earth ore has been investigated and the mechanism is discussed. The result shows that the leach promoting reagent LPF can enhance the leaching extraction of rare earth ore effectively. With the addition of LPF to the lixiviant at a concentration of 0.1%, the leaching extraction increased by more than 8%, the ammonium sulfate concentration could be decreased by 25%, and the leaching liquid/solid ratio reduced by 34%. The mechanism analysis shows that LPF can react with rare earth ions and form soluble coordination compounds, thus reducing the activity of the leached rare earth ions, increasing the concentration difference for ion diffusion, and promoting the rare earth leaching process. These results will hopefully help point to a new approach to making the leaching process of low-grade weathered crust elution-deposited rare earth ore more efficient and with lower lixiviant consumption.

Jan 1, 2014

By J. Oliveira, A. R. Barnes, R. Pandher

Sub-stoichiometric roasting of arsenic-bearing copper ores is a well established practice. However, ores containing calcium commonly prove challenging where very low arsenic levels are desired, but the reasons for this phenomenon have largely been speculative. In the course of treating arsenicbearing copper ores by partial roasting in fluid bed reactors, XPS encountered one of these Ca-bearing ores which proved a challenge to roast to acceptably low levels of arsenic. Mineralogical examination of the calcines using a combination of XRD (X-ray diffraction), QEMSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) and EPMA (Electron Probe Micro-Analysis) helped to identify the arsenic bearing species and assisted in developing a workable theory on the sequence of reactions occurring during the roast. With the assistance of thermo-chemical modelling, this allowed adjustment of the roasting conditions to minimise the amount of arsenic retention in the calcine in spite of the presence of calcium in the ore and advance the roasting program to a commercially acceptable solution.

Jan 1, 2014

By A. S. H. Kabir, I-H. Jung, J. Su, S. Yue, M. Sanjari

The final mechanical properties of wrought magnesium alloys are mostly controlled by microstructure and crystallographic orientation or texture. In common magnesium alloys, grain coarsening occurs during annealing process and formation of undesirable basal texture cannot be changed markedly. The aim of this work is to investigate the effect of static precipitation on microstructure and texture evolution during annealing at 250 °C after warm rolling of Mg-Al-Sn alloy. Mg-3Al-3Sn (wt. %) alloy has been designed using thermodynamic modeling software, FactSageTM, based on forming target stable and incoherent Mg2Sn precipitate within the industrial deformation temperature range. Microstructures and precipitation were investigated by optical and scanning electron microscopes and macro-texture was measured by X-ray diffraction (XRD) techniques. It was found that static precipitates form in a large scale at the recrystallized grain boundaries and retards the grain growth during annealing. Slight weakening in basal texture was also observed during annealing.

Jan 1, 2014

By R. H. McCorkell

Measurements of radon in air and aqueous solutions can be affected by leakage from vessels in which samples and standards are kept and by absorption and later release of radon by the materials of these vessels. The author had received various oral communications concerning the se processes : e.g ., that natural rubber and greases absorb large amounts of radon, whereas silicone rubber and grease do not; and that radon is readily lost from polyethylene bottles and that inverting glass bottles containing aqueous samples reduced radon loss from them . However, the results of actual tests and quantitative data showing these effects were not available. For this reason, it was necessary to make numerous measurements of the leakage and absorption of radon in the course of designing apparatus and methods for measuring radium and radon concentrations. It was thought that the data obtained might be of use to others, and consequently they are compiled in the present note .

Jan 1, 1980

By Robert B. Parsons

"Effective January 1, 1990, mines in British Columbia are subject to a new provincial mining tax statute, the Mineral Tax Act. Under this Act, mines are subject to a two-tier tax system, with a minimum tax payable on ""net current proceeds"" and a higher tax paid on net income. For many mines, the present value of tax paid under the new rules should be comparable to the amount paid under the old rules. Earlier cash payments could pose difficulties, particularly for smaller mines, but existing producing mines could benefit in the short-term.IntroductionEffective January 1, 1990, British Columbia has replaced the provincial mining tax regime under the Mineral Resources Tax Act with a new system under the Mineral Tax Act. The new rules borrow some ideas from other provinces (New Brunswick's two-tier concept, and Saskatchewan's indexed costs) with a view to levying a tax that is fairer to both the producer and the province."

Jan 1, 1990