Search Documents

By J. M. Goris

"Researchers at the U.S. Bureau of Mines are conducting research on cable-type ground supports to assess their material and support properties and to provide design criteria for implementing cable supports as a workable roof control system under various underground mining conditions. Much of this work involves laboratory assessment of the material and support properties of cable supports using both conventional and birdcage steel cables. Included in this assessment are single and double cables, effects of changes in embedment length on support strengths, water-cement ratios, use of breather tubes, and pumpability and water-bleeding properties of grouts.IntroductionSince cable supports were introduced in the early 1970s, considerable research has been conducted in laboratories and at mine sites to understand their behaviour. The U.S. Bureau of Mines began a laboratory evaluation project in 1985 at the Spokane Research Center (SRC) to study the behaviour of cables supports under uniaxial loads so that the effects of various cable support components, such as grout and breather tubes, could be identified. Other objectives were to compare the behaviour of various types of cables and grouts and to collect meaningful data for numerical analyses. Pull tests were conducted to determine how cables supports reacted under uniaxial loads and how they failed when ultimate loads were exceeded. Such data are essential for the development of numerical models for analyzing rock mass behaviour when the rock is supported with cables.Test ProgramBecause each cable support can be composed of either single or double cables as well as a breather tube, pull tests were designed to include a variety of samples containing these components. A series of samples containing a single conventional cable, a neat cement grout having a water-cement ratio of 0.45, and no chemical additives was selected as a standard (Table I). Then one component in the system, such as the presence of a breather tube, was changed, and results of tests compared to results obtained for the standard samples to determine what influence that component might have on the behaviour of the support system. If significant changes in test data occurred, they could be attributed to that one component. To control the quality of the samples, the physical condition of the cables and tubes were monitored closely, and compressive and tensile strengths as well as flow properties were determined for the grout used in each test series."

Jan 1, 1991

By Michel Aubertin

Les haldes à stériles contenant des minéraux sulfureux réactifs constituent un milieu favorable à la production du drainage minier acide (DMA). Au sein de ces haldes, les processus physiques, géochimiques et biologiques qui mènent à la production du DMA sont nombreux et complexes. Un des aspects critiques qui affecte la génération de DMA est la distribution et le mouvement de l?eau dans les roches stériles. La modélisation numérique est un outil qui permet de comprendre, pour éventuellement contrôler, les mouvements de l?eau (et donc réduire la production du DMA) dans les haldes pendant la période d?exploitation de la mine et à sa fermeture. Plusieurs simulations numériques des écoulements non saturés dans des haldes ont été effectuées. Pour ces simulations, on a considéré divers types de matériaux, diverses conditions atmosphériques et diverses configurations géométriques. Les simulations réalisées montrent que l?on peut contrôler les mouvements de l?eau en introduisant des couches de matériaux fins intercalées dans les haldes formées de matériaux grossiers. Des couches horizontales ne sont cependant pas appropriées puisqu?elles peuvent, dans certains cas, favoriser la création de zones humides susceptibles d?amplifier les effets du DMA. Une faible inclinaison des couches de matériaux fins vers l?extérieur permet de palier à ce problème. Les couches inclinées favorisent un drainage des haldes vers la périphérie. Ceci a pour effet de garder sèche une grande partie des stériles et de réduire, par le fait même, la production du DMA.

Nov 1, 2002

By J .. R. Dalton

"Blasting in high sulphide content ores presents at least two major safety considerations: (1) compatibility of the explosives with the ore while resident in the borehole; and (2) introduction of a flame and shock producing explosive into this environment, while minimizing the risk of reactive ignition in the chemical reaction products/sulphide dust cloud resulting from the detonation. This paper will discuss only the second consideration, i.e. post detonation reactivity.The ETI (Explosives Technologies International) Technical organization, in consultation with the U.S. Bureau of Mines, reasoned that the most relevant considerations in the development of an explosive for this application are:• minimization of reactive gaseous detonation reaction products;• flame duration reduction;• flame temperature reduction;• increased explosive sensitivity;• reduced probability of ""low order"" detonation; and• maintenance of energy level as high as possible.Obviously, not all of these are totally independent properties, i.e. increased sensitivity will reduce the probability oj low order detonation as will higher energy levels. However, these considerations were examined separately as if they were independent."

Jan 1, 1994

By Roy Sage

Overview ? History ? background to current programs ? Kyoto status ? Support for technology development ? Support for GHG reduction ? Sources of information History ? 1988 - Toronto Conference - The Changing Atmosphere ? Proposed target ? CO2 levels reduced to 20% of 1988 levels by the year 2005 ? 1992 - Canada signed Framework Convention on Climate Change at the UN Conference on Environment and Development in Rio de Janeiro in June 1992 ? Canada launched the National Action Plan on Climate Change ? Kyoto protocol adopted in principle in 1997

Nov 1, 2002

Agenda 1.Energy consumption and energy costs ?focus and failings 2.Energy efficiency methodologies, people and supporting tools 3.Energy cost saving case studies from three minerals processing plants 4.The operations team and the supporting role of Operations IT 5.Conclusion: Reducing energy consumption and energy costs There are many good Energy Efficiency Methodologies ?Energy and GHG Emissions, Management Guidance Document, The Mining Association of Canada ?Energy Savings Toolbox ?An Energy Audit Manual and Tool, Canadian Industry Program for Energy Conservation (CIPEC) ?Lean and Energy Toolkit, Achieving Process Excellence Using Less Energy, www.epa.gov/lean ?Energy Efficiency Opportunities Assessment Handbook, www.energyefficiencyopportunities.gov.au

May 1, 2010

By S. C. Cohen, A. F. Mikkelsen

"This paper describes the improvements made to the operation of a liquid phase, 300°C, heat transfer system in the paste plant of an aluminum smelter. These improvements were achieved by replacing the original heat transfer fluid, a synthetic aromatic, with a new technology, petroleum-based product. This new fluid, Calflo HTF, provided better thermal stability, with lower toxicity, and improved plant working conditions.The procedures for fluid selection, changeout and performance monitoring are described along with a summary of control analysis over the last three years."

Jan 1, 1993

By Arthur Lieu

Outline Removal mechanisms of Se and Mo in the Key Lake Bulk Neutralization circuit Bulk circuit Detail process modification in the Key Lake BN circuit Process performance after commissioning Objective Legacy effects of Se and Mo from the historical operation of Key Lake mill were shown to have an negative effect on the regional biota in the downstream environment. The water treatment circuit was not designed to remove Se and Mo from the effluent. Reduce Se and Mo concentrations in final effluent under0.028 0.028 ppm ppm and 0.3 and ppm ppm(CNSC regulatory limits).(limits).??????

Nov 1, 2011

By K. D. Card, K. Howard Poulsen

Abstract - The Archean Superior Province craton and the Paleoproterozoic Penokean Orogen are major geological sub-divisions of the southern Canadian Shield and account for much of the metallic mineral production of North America. The Superior Province experienced a mainly Archean history involving several cycles of volcanism, plutonism, and tectonism, primarily in the Neo-archean but also including Meso-archean and Paleo-archean cycles as well. Superior Province consists of northern and southern high-grade gneiss sub-provinces and a broad central region of alternating greenstone-granite and metasedimentary belts. The sub-provinces may represent tectonic terranes assembled in the Archean by accretion processes similar to those of some Phanerozoic orogens. Most of the mineral deposits, including VMS, intrusion-related, and lode gold deposits occur in the greenstone- granite sub-provinces where they were formed in an interval of 100 million years or less around 2.7 Ga. The Paleoproterozoic Penokean Orogen comprises supracrustal sequences deposited in fault-controlled epicratonic and rifted margin settings developed on and about the Superior craton. Deposition of the ~2.4 Ga Huronian Supergroup and its paleoplacer uranium deposits in the eastern Penokean Orogen, and their pre-2.2 Ga deformation, were probably unrelated to the deposition of the ~2.1 Ga Marquette Range and Animikie groups and their major taconite iron formations in the west. However, these sequences were deformed together during the ~1.85 Ga Penokean Orogeny which resulted when an assembly of island arcs containing VMS deposits, the Wisconsin magmatic terrane, collided with the Superior block and its Paleoproterozoic cover. The Sudbury structure with its world class Ni-Cu-PGE ores was also formed at this time, possibly triggered by meteorite impact. Metallogenic patterns in the Paleoproterozoic rocks were controlled by a complex interplay of factors including tectonically controlled variations in deposition and deformation, distribution of mineralization in the Archean basement, and oxyatmoversion, the transition from anoxic to oxygenic atmospheric conditions that occurred during the deposition of these sequences.

Jan 1, 1998

By Carlos Nieble

Ferteco Mineracao, belonging to the CVRD group, is one of the several iron ore mines in the south east of Brazil. Some of these mines have pit walls of over 350-m height and operations under difficult geo-technical conditions are steadily increasing. In order to mine the 15 million tonnes of high grade hematitic ore remaining in the Fabrica pit, Ferteco had to deal with the following restrictions: Warrant power to its concentrator and pellet plant, relocate the load-out rail road loop, stabilise a poor phillyte slope, relocate a creek on a bench, lower the water table and mine at maximum angles at a slope with phillyte and loose itabirites directly under the rail road loop. Considering these aspects, 3 stages of operations were designed, considering a safe operation, but with the lowest possible security factors at the last mining stage, before the pit would be filled in again with tailings. Stage one above the rail road loop and below the high tension power mast, where the poor phillyte slope was secured by a flexible retaining wall, using old rails and anchors up to 27 meters (80ft) with a working pressure of up till 30 tonnes and stage two with different slope angles, and deep wells, high wall blasting perpendicular to the highwall with relief holes and rerouting the creek in steel half culvert and stage three, the filling in with tailings and recuperation of the deep well pumps. Following studies and analysis were made: Geotechnical and geological studies of all rock formations including rock strength test, a hydrological study to define the lowering of the ground water level, slope stability analysis for every bench and all possible combination of benches, definition of blasting parameters close to the pit slope, a monitoring plan, including topographical movements, vibrations due to blasting, piezometers and pressure cells as well as a plan how to fill up the pit again with tailings in combination with the rising of the ground water level. A close co-operation between the geo-technical consultant, pit operations, the blasting contractor and the geological department resulted in an operation without any incidents, lowering the pit with an additional 3 benches and mining an additional 5 million tonnes of high grade ore.

May 1, 2003

By Shinji Shirakawa

The gold wire bonding technology is widely used for electrically connecting aluminum pads on IC devices to external terminal of semiconductor. In 1960?s, the tensile strength of gold bonding wire was about 100 MPa only. However, recently the wire with 300 MPa in strength has been developed. Since the gold bonding wire was started to use for IC package in early 1960?, the many types of gold bonding wire has been developing continuously in order to meet market?s needs, such as high density, small size and thin type of IC packages. Moreover, electronic equipments were used in automobile applications and also demanded good reliability under severe temperature environment. Thus Au-Pd alloy wire has been introduced instead of the wire with 4N(99.99wt%) purity gold to provide excellent reliability in Au-Al bond interface. The phenomena at Au-Al interface in the high temperature storage have been already explained by several studies as follows. There are five phases of inter metallic compound (IMC) between gold and aluminum. Just after bond gold ball on aluminum pad, Au5Al2 phase was formed and occupied almost all of IMC area. During high temperature storage test, Au5Al2 phase transformed to Au4Al phase, then this phase was corroded by Bromide (Br) ion that was isolated from molding resin. Thus the reliability between Au and Al degraded. In case of Au-Pd alloy wire, the concentrated palladium phase (Au-Pd-Al) was formed at the interface between Au alloy ball and Al pad. The Au-Pd-Al phase prevented from transforming between Au and Al, therefore Au5Al2 phase was hard to transform to Au4Al phase. Consequently the reliability at the interface between Au alloy ball and Al pad was less degradation. However, in recent study using several advanced analysis technique, Au4Al phase was found at the interface between Au alloy ball and Al pad same as the case of conventional gold wire (4N purity gold bonding wire). It was suggested that the formation of concentrated palladium phase (Au-Pd-Al) related the excellent reliability at ball bonding process.

Oct 1, 2003

By Akira Miura, Katsuyuki Sato, Yuken Fukano

JX Nippon Mining and Metals Corporation has developed the JX Iodine Process, which is an innovative and patented copper-leaching process for low-grade primary sulfide ores. This process consists of the irrigation of ferric iron and a low concentration of iodide solutions. One-meter column leaching tests were conducted on ore samples from two different mines. At the end of experiments, the total copper recovery exceeded 70% for Sample A and 50% for Sample B with the iodine method, which was significantly higher than that with conventional ferric leaching of 14% for Sample A and 20% for Sample B. To elucidate the reason for the JX Iodine Process effectiveness, cross sections of leached residues were studied. Reaction products were confirmed around chalcopyrite even in the central area of particles in Sample A, however, reaction products were recognized at a depth of only 1 mm from the ore rim in Sample The resistance of Sample A to the leachate appeared to be lower than that of Sample B because Sample A had a high permeability and porosity, whereas Sample B had been affected strongly by a potassium alteration. No reaction products were visible on conventional leaching samples, even at the ore surfaces. INTRODUCTION Hydrometallurgical copper leaching (heap leaching or dump leaching) has been used extensively for copper recovery from oxide and secondary-sulfide ores, but not for primary copper sulfides, which contain mainly chalcopyrite as copper minerals. Although they are major resources of copper, primary copper sulfides are difficult to process because of their refractory nature. Extensive leaching studies have been carried out to leach primary copper sulfides (chalcopyrite), including biological and chemical, using a variety of oxidants and additives to enhance copper recovery. Watling (2013) reviewed acid-chloride-oxidizing agents with chalcopyrite. Abdollahi et al. (2015) tested silver as a catalyst for bioleaching with a chalcopyrite-bearing molybdenite concentrate. Hiroyoshi, Miki, Hirajima and Tsunekawa (2000) found a specific redox-potential zone for high-speed chalcopyrite leaching by controlling the ratio of ferric and ferrous iron. However, no ambient-temperature economic process has been developed for leaching primary copper sulfide, which usually has a low copper grade.

Jan 1, 2019

By L. J. Surges, C. Bazin, D. Hodouin

"A kinetic model was developed for the conditioning and flotation processes of an industrial lead concentrate dezincing circuit. The models were incorporated into a flowsheet simulator. Simulation results demonstrate the advantages of split conditioning of coarse and fine particles and the potential of this approach for the production of the heuristics required for the development of intelligent control strategies.The conditioning model relates the proportions of activated and hydrophobic surfaces and residual reagent concentrations to activator and collector reagent flowrates. The model accounts for the solids and water flowrates, and for the solids grade and size distribution. The flotation model uses the predicted proportion of hydrophobic mineral surface, the aeration rate and the froth depth to estimate cell, bank and circuit performances. IntroductionFlotation has been the object of modelling and simulation studies for more than two decades. The process is usually modelled as a kinetic one in which the particle flotation rate constants are key parameters. Rate constants are related to the operating variables (pH, reagent flowrates, aeration rate, etc), however these relationships are seldom established in the literature.In spite of the large amount of literature on flotation modelling and simulation, few papers deal with the interaction between flotation rate constants and operating variables. This important gap, which was identified in the early seventies by Woodburn (l970), still exists. One of the first attempts to include operating conditions in a flotation simulator was made by King (l973), who explicitly introduced the aeration rate into an air bubble loading model. Lynch et al. (1981) used an empirical model to relate the proportion of slow floating particles to the ratio of collector per ton of ore. Such empirical relationships are difficult to calibrate and cumbersome to use when an activator and a collector are added to slurries in which particle size distribution and surface characteristics are changing. Eascur and Herbst (l982) relate in a fundamental way the mineral flotation rate constants to the aeration rate, froth depth, agitation and frother concentration, however the model does not account for reagent flowrates. Niemi et al. (1982) have proposed a model for the conditioning of minerals and included it into a conventional flotation simulator."

Jan 1, 1988

By J. G. Schofield, R. C. Francki, K. M. Donaldson, F. E. Ham

"Developments in pyrometallurgical technology have led to larger furnaces operating under more intense process conditions. In order to maintain the reliability of these furnaces, which are frequently single-line units, the design of the refractories, cooling systems and bindings has become more critical. Traditional thermal and chemical requirements for the refractory to resist slag attack must still be carefully determined. The larger, modem furnaces have placed a new emphasis on the structural properties of the refractories as well as their thermal properties to suit the extensive cooling systems. Based on operating experience, supported by computer models, the refractories and bindings are designed to work together to accommodate the thermal expansions and contractions in order to minimize permanent furnace growth and the risks of leaks. IntroductionElectric furnaces are used extensively in smelting copper and nickel ores and concentrates. Laterite nickel ores and high-magnesia copper, nickel and platinum sulphide concentrates are smelted virtually exclusively in electric furnaces to accommodate the high melting point of the slags produced. Although a number of smelting processes using oxygen-enriched and/or preheated air have been developed to replace reverberatory furnace smelting of conventional copper and copper-nickel concentrates, (lnco, Noranda, Outokumpu, Mitsubishi) electric matte furnaces remain a strong process alternative for these concentrates, either as the primary smelting vessel or for cleaning the slags produced from these processes.The development of large, high-powered furnaces has been an important factor in the growth of electric smelting technology, as evidenced by the list of operating matte and ferronickel furnaces shown in Table I. Because the compressive forces required to maintain a tight, leak-free furnace increase with furnace dimensions, the selection and design of the furnace refractories, cooling systems and bindings require increased attention."

Jan 1, 1993

By Rick Hyndman

? Context: Ø Global action on climate change ? The situation of trade-exposed industry sectors ? The federal government?s draft plan for industry ? CAPP?s position ? Canadian emissions & Canada?s Kyoto target Simple Economic Theory of Dealing with Externalities ? Put cost on emissions Ø Carbon tax Ø Emission trading with auctioned permits ? GHG costs get reflected in the prices of energy alternatives, goods & services Ø Decisions driven by changes in relative prices ? Switching to lower emission fuels ? More energy efficient ways of producing ? More energy efficient appliances, cars, housing ? Reduced demand for energy intensive goods & services ? Anticipation of higher CO2 price drives low CO2 technology Development

Nov 1, 2002

By A. Liard, H. Sommelet, G. Sauriol

"Description des études qui ant conduit à la conception spécifique du système de drainage de la mine à ciel ouvert. Les approches différentes sont examinées ainsi que la valeur du système recommande.IntroductionLa Division Mines Gaspé de Mines Noranda Ltée exploite un gisement de cuivre par mine souterraine et mine à ciel ouvert à Murdochville, Québec. L'exploitation par mine aciel ouvert a commencé en 1965 avec une operation à flanc de montagne. Elle se poursuit actuellement sous Ie niveau de la vallée dans une fosse dont Ie diamètre est de I'ordre de 800 m (2,600 pi), et la profondeur de 150 m (500 pi) sou s Ie fond de la vallee. Elle doit atteindre une profondeur de 360 m (l, 180 pi) sous Ie fond de la vallee , avec des murs hauts de 360 à 490 m et des pentes moyenne de 44°. Le rythrne d'extraction est actuellement de 85,000 tonnes par jour.Dans Ie cadre des etudes entreprises par les Services Techniques de la Division Mines Gaspé, la compagnie Géomines Ltée a été consultée pour étudier les conditions hydrogéologiques et hydrologiques locales et participer a la conception d'un système de drainage superficiel et souterr ain. Un tel systerne de drainage visait: a éviter les importantes venues d'eau qu i affectent I'exploitation en periode de crue; amaintenir les pressions hydrostatiques au sein des parois de la fosse dans les limites imposees par les etudes de stabilite des pentes réalisees par la Mine.Les principales étapes de cette etude ont porté sur: la collecte et la compilation des données sur la géologie, l'hydrologie et l'hydrogeologie du site; . la détermination des caractéristiques hydrauliques du milieu rocheux à partir d'études structurales et de test s de perméabilité;"

Jan 1, 1981

By J. G. Henning, T. R. Yu, J. E. Croxall

"Test work was carried out to investigate the thermal response of loose and solid rock under varying environmental conditions. The primary interest was to develop a technique that could be used to increase the thermal variation between loose and solid rock for better detectability of loose rock underground with a thermal imaging infrared scanner.A variety of thermal enhancement methods were evaluated both in the laboratory and in the mine environment. Air temperature variation created by the exhaust from diesel driven, mobile mining machinery was studied in detail. When sufficient hot exhaust was supplied to the air, unsteady thermal conditions became more pronounced on the rock surf ace. This allowed a greater percentage of loose rock to be detected by a high-resolution infrared scanner within minutes.The degree of thermal enhancement of loose rock was found to be dependent directly on the thermal conductivity of rock, looseness, air temperature change, and inversely on the size of loose, airflow rate and distance downwind from the heat source. It was also found that an air temperature rise of at least r c, or rock temperature differential of1°C was necessary for minimal thermal enhancement required f or infrared detection."

Jan 1, 1990

By James Logan

BC Alkaline CuBC Cu--Au PorphyriesAu Porphyries ?Formed over narrow time interval ~205 Ma ?from silica deficientvsalkali-enriched magmas ?At shallowdepths ?Structuralcontrol ?Cu-Au-Ag, trace Mo ?Oxidized system anhydrite, magnetite ?Multipleintrusions & multiplemineralized centres

May 1, 2006

By D. Doyle, T. Cienski

"This paper presents and discusses the results of a detailed study conducted on the subject of energy consumption in the comminution of industrial minerals. The study was based on pilot circuit testing, plant operating data collection, detailed equipment data and literature research. The areas covered by investigations include: high efficiency classification; air classifiers for cement grinding circuits; grinding aids in dry grinding; and dry grinding circuit control based on particle size measurement. Results obtained indicate a large potential for the reduction of energy consumption, in particular in the cement clinker grinding circuits. Better classification techniques and correct application of grinding additives can significantly reduce power used per tonne of product and also substantially increase grinding circuit output."

Jan 1, 1992

By M. A. Vos

"Cretaceous sands and clays underlie an area of approximately 5,000 km2 in Northern Ontario, southwest of James Bay. The deltaic deposits occur as a wedge of continental sediments to the north of an east-trending fault scarp referred to as the Precambrian Escarpment. They rest on older sedimentary formations of the Moose River Basin (Jurassic, Devonian) and are covered by glacial tills and marine sediments of the Quaternary period. Outcrops are restricted to occasional exposure in the deeply incised riverbeds.In 1975 and 1978, drill programs sponsored by the Ontario Government provided new information on the extent and quality of the deposits. Fourteen holes at approximately 12-km intervals were drilled to a maximum depth of 189 m by reversed- circulation chip drill methods. Some core was obtained as well. Analytical results show that the thickness of Cretaceous deposits exceeds 100m in several instances. Abundant kaolinitic clay and quartz sand of glass-grade quality, both unique materials in Ontario, are available in an area where hydroelectricity and lignite resources combine to enhance the energy outlook.IntroductionThe presence of refractory clay in deeply incised riverbeds in Northern Ontario was known to geologists travelling the rivers as early as 1875. Robert Bell (1877) reports outcrops of clay and lignite on Coal Brook, a tributary of the Missinaibi River. E.B. Borron in 1880 collected a sample of clay from the bed of the Missinaibi River which H.H. Croft of the University of Toronto considered to be ""nearly if not quite, equal to the Cornish clay used in the manufacture of English porcelain"" (Keele, 1920, p. 42). The Cretaceous age of the clay, sand and lignite deposits was determined with the help of plant remains collected by Keele. He referred to the deposits as the Mattagami series, which later became the Mattagami Formation."

Jan 1, 1982

By S. Yannacopoulos, L. Bichler, P. Wanjara, J. Gholipour

Characterization of a virgin and in-service Inconel 718 alloy was undertaken to study the changes caused by the service conditions on the grain size, ?? phase, MN-type nitrides and MC-type carbides. The size, distribution and volume fraction of these phases and grain size were studied using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and electron backscattered diffraction (EBSD) analyses. A considerable difference in the grain size, as well as distribution and volume fraction of the precipitates was observed in the in-service material as compared to the virgin Inconel 718. As a result of these microstructural changes, a notable dissimilarity in hardness between the materials investigated was observed. The results presented in this study are important for proper development of repair parameters and heat treatment of in-service Inconel 718 material.

Jan 1, 2014