Search Documents

By A. J. Ouellet, A. Coulombe, B. Salmon

The no. 7 vein system cuts the Ventures gabbro which has undergone folding and fracturing; the latter, in response to movement on the nearby Campbell Lake fault. It fills a shear fracture which pinches and swells in the upper mine levels but has a more uniform width in the lower levels. The best copper and gold grades in the upper levels occur in the widest parts of this structure. The vein is richer in quartz on upper mine levels and in carbonate on lower levels. The north wall of the vein is more affected by major and minor element wallrock alteration than the south wall. The isocumulative ci;rves for gold and copper show a direct correlation between the two metals in the upper levels and their increased concentration in the wider parts of the vein. Gold grade decreases in lower levels. A proposed structural model identifies the no. 3 and no. 7 veins as second order conjugate fractures, related to the Campbell Lake fault. The fractures pattern suggests that a conjugate system developed between these two parallel veins as a consequence of rock competence and a relatively low confining pressure.

Jan 1, 1984

By K. El-Ouassiti, M. Zouadi, C. Bazin, D. Hodouin

Data reconciliation techniques are used to attenuate the effect of measurement errors and estimate unmeasured variables. This paper illustrates the application of data reconciliation to hydrometallurgy processes using measurements from leaching and solvent extraction obtained from laboratory experiments. The application of data reconciliation provides an efficient way to detect gross and systematic errors and produces reliable performance indices for process evaluation.

Jan 1, 2005

By J. Baumbach, H. Bombach, M. Stelter

"Today technical electro-refining processes for copper exclusively use sulfuric acid, for silver refining nitric acid electrolytes are used. Sulfuric acid is characterized by very good chemical and electrochemical stability, good conductivity and low cost. The disadvantages of sulfuric acid are the precipitation of fine-grained cathodes with smooth surfaces only by using additives like glue, thiourea and chloride. In case of silver the electrolyte is electrochemical unstable and bears the risk of the formation of toxic NOx when pH is too low. A second disadvantage is the form of electrodeposition of silver as dendrites with their removal from the bottom of the Möbius cells.This paper reports the results concerning the application of an alternative electrolyte in copper and silver electro-refining. At first the electrolyte was characterized by the determination of current density potential curves. Electrolysis experiments were performed in laboratory scale using technical anodes for copper and synthetic anodes for silver. During the copper tests the solubility of contaminations from the anodes and the amount and chemical composition of the anode slimes were determined. Moreover the influence of current density, electrolyte temperature and the effect of several additives on the precipitation and chemical purity of the cathodes were investigated. In all experiments cell voltage as well as anodic and cathodic polarization was measured and current efficiency and specific energy consumption were calculated. A comparison with the results with those of tests using conventional sulfuric acid electrolyte shows the advantages and disadvantages of both systems, additionally the technical application chances and limitations for the new electrolyte. This electrolyte enables the precipitation of smooth copper cathodes with low silver and sulfur concentrations even at lower temperatures without any additive. For silver refining the electrodeposition of compact silver sheets is possible, that can be stripped comparable to those in copper electro-refining."

Jan 1, 2016

By Glenn Davis

In the world of large scale open pit mining, the majority of a mines operating cost is tied to the removal and transportation of the overburden waste material. Typically, many large haul trucks are employed to transport this overburden from each excavating face. The trucks transfer the waste material from deep within the pit to waste dumps on the surface incurring significant costs in operators, road construction and maintenance, vehicle maintenance staff and support facilities, fuel, tires, and spare parts, as well as the capital cost of the truck fleet itself. In addition, the haulage of the actual mined material carries similar operational costs. In both cases, these costs grow as the mine face advances and pit haulage distances increase. Reducing truck haulage is one key to the success of the Dual Truck Mobile Sizer (DTMS). Being the world?s first fully mobile truck dump station, transportation costs can be significantly reduced as the mine face advances. Furthermore, when used in conjunction with a shiftable face conveyor and a mobile overland hopper, substantial cost savings can be achieved. The mobility of the system allows for the considerable reduction in the haul truck fleet. Overall mine site emissions levels are greatly reduced by the fleet elimination, as well as keeping the majority of the hauls on a flat grade within the pit. Emission levels on a typical truck will dramatically spike as the angle and the length of the haul are increased. Moreover, comparing diesel engines versus electric powered conveyors to move the material contributes to the realized savings.

May 1, 2010

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of the overall study, a comprehensive description of physical and chemical characteristics of fine tailings generated by caustic and non-caustic processes was carried out. Ultimately, the influence of these fundamental properties on the compressibility, hydraulic conductivity and shear strength properties of the fine tailings was assessed. The characteristics of the fine tailings are presented in terms of index properties, mineralogy, specific surface area, water chemistry, liquid limits, particle size distribution and structure. A difference in water chemistry was concluded to be the cause of substantial differences in particle size distributions and degree of dispersion of the comparable caustic and non-caustic fine tailings. The degree of dispersion was consistent with predictions for dispersed clays established by the sodium adsorption ratio (SAR) values for these materials. A linear variation of increasing dispersion with increasing SAR up to a SAR value of about 40 has been suggested, above which fine tailings are completely dispersed. The observed dispersed or flocculated structures (viewed using a scanning electron microscope) supported the predictions based on SAR values.

Jan 1, 2010

By N. Schmalbein, L. von Ketelhodt, L. Kotelo

"The mining industry continues to remain challenged. Lower commodity prices, increasing labor costs and more importantly diminishing reserves are amongst some of the primary factors contributing to the difficulties faced. Ore sorting technologies have demonstrated their potential to improve the downstream beneficiation performance. The general processing route sees all primary crushed material milled for liberation and then processed in accordance with characteristics of the gold therein, i.e.: refractory golds would require direct leaching or oxidation whilst free gold would follow the conventional cyanidation process, after gravity concentration. Ore dilution increases the associated operating costs within each stage of this process. The opportunity to process the same throughput at a higher grade can only be achieved through pre-concentration. Sensor based sorting has been examined on numerous occasions by various gold producers. Test work carried out on different bulk low grade gold ores has shown the successful applicability of ore sorting to remove waste, whilst maintaining high recovery rates of gold. The results of a combined XRT/Laser sensor sorter have shown grade improvements of over 300% from feed grades of 0,25g/t to 1,15g/t at gold recoveries of 66% and waste ejection rates of 85%. This paper presents some of the results from the work undertaken by STEINERT with respect to gold sulphide ore sorting and presents a modelled financial scenario, which can enable a company to target and reclaim low grade ores.INTRODUCTION The mining and minerals processing industry presents with many different challenges including, volatile commodity prices, increasing labor costs and more importantly diminishing reserves. Conventional processing routes will continue to play a crucial role in the beneficiation process, however innovative methods of reducing operating costs and optimizing on the overall circuit performance is where technologies such as sensor based sorting come into the fore. Sensor based sorting as a dry mechanical process not only reduces water consumption by eliminating unnecessary waste but also reduces the requirements for reagents in the downstream processes. Sensor based sorting under dry conditions presents a highly efficient alternative to wet pre-concentration methods such as dense medium separation (DMS)."

Jan 1, 2017

By E. Asselin, P. Sauve, H. Salomon-de-Friedberg

"Residues from the CESL Copper process were leached using the CESL Gold process. The kinetics of reaction were confirmed to be fast with over 50% of the gold consistently extracted within 2 minutes of leaching. Final gold extractions under the conditions tested here were between 80-90% obtained within 90 minutes. A model for the CESL Gold process was developed. This model is slightly different based on whether the copper concentrate leach residue was ground or unground prior to leaching: the gold leaching rate constant is approximately twice as fast for the ground samples. Unground residues had a P80 of 13 ?m whereas ground residues had a P80 of 10 ?m. The model predicts a 43% decrease in leaching time for ground residue versus unground residue to achieve the same extraction under otherwise identical conditions. The model was more accurate for the ground samples. INTRODUCTIONTeck's CESL Process (Jones, 1996) was developed to provide an economically attractive alternative to traditional copper smelting. It has since evolved to also deal with copper concentrates containing valuable impurities such as nickel and undesirable ones, such as arsenic, while reducing downstream costs. Effective recovery of gold and silver is essential to the economics of the CESL Process. The Brook Hunt 2007 copper concentrate assay data (Wood-Mackenzie, 2007) were examined to determine the ratio of gold plus silver value relative to the contained copper. As indicated in Figure 1 below, nearly two-thirds of concentrates have 10% or more of their total value tied up in their precious metals content.CESL has extensively examined the recovery of gold and silver at bench, pilot and demonstration scale, which has culminated in the present CESL Gold Process (Barr et al., 2007). The process targets the precious metal contained in the leach residues produced in the copper portion of the flowsheet. This residue has two primary components which influence downstream processing. The major iron-rich fraction (-75 wt%) of the residue is a mixture of various forms of iron oxide precipitates including hematite and jarosite (Sahu and Asselin, 2011). The iron fraction ranges from amorphous to crystalline in nature depending on the compound precipitated, upstream operating conditions and feed material composition. The lesser, but by no means less important, fraction is a mixture of elemental sulphur and unreacted sulphides (principally pyrite).Elemental sulphur formed during the oxidative leach of the copper concentrate reacts with cyanide to form thiocyanate (SCN-) making a traditional cyanide leach approach too costly. Since the SCN formation reaction strongly depends on contact time with the CESL residues (Po, 2007) short contact times were preferred. This factor guided the development work towards the eventual room temperature, pressure cyanidation process which results in near complete gold dissolution in 90 minutes. A recent CESL gold demonstration campaign treating 1.5 t/d of residue from the copper oxidation step achieved an average gold extraction of 91% (96% maximum)."

Jan 1, 2012

By D. C. Peck, H. D. M. Cameron, N. M. Halden, L. S. Jobin-Bevans

Abstract-The late Archean Pipestone Lake anorthosite complex (PLAC) is a 0.9 x 17 km sill-like layered intrusion that is part of a suite of coeval megacrystic anorthosite bodies in the Cross Lake region, northwestern Superior Province. Exploration for Ti-V-Fe oxide mineralization and concurrent geological investigations have contributed to a greater understanding of the lithostratigraphy of the PLAC and its oxide mineralization. Mapping and drill core studies have established a laterally continuous igneous stratigraphy comprising six leucogabbro/anorthosite zones and three melagabbro/gabbro zones. Field evidence, including disrupted blocks of layered units, scour contacts, and size-graded and modally-graded layering, suggests younging towards both the northern and the central parts of the complex. A decrease in the anorthite content of the feldspars from An75 in the south to An30 in the north suggests that the magmas become more evolved to the north. Macrorhythmic layering and gross morphological features suggest that the PLAC crystallized from four major influxes of geochemically similar basaltic magmas. The paucity of magmatic erosional features in the PLAC indicates that layering developed in a relatively static magma chamber, so that in-situ crystallization processes are required to account for the observed petrologic diversity. Drilling has confirmed that a significant Ti- V-Fe resource is contained in two of the four discrete mineralized subzones in the PLAC. Textural evidence and the stratiform nature of the oxide-enriched subzones are consistent with a magmatic origin for the oxide mineralization.

Jan 1, 1997

By D. Sprott, P. A. Kirsch, J. Harris, D. Cliff

This paper details the work of RISKGATE, the largest Australian Coal Association Research Program (ACARP) occupational health and safety initiative to date. The program is an interactive online risk management system developed to maximize health and safety performance in the coal mining industry by implementing continuous improvement in managing major unwanted events. The comprehensive knowledge base covers tires, collisions, fires, isolation, strata control underground, ground control open cut, explosions, explosives, manual tasks, and slips/trips/falls. All major Australian coal mining companies contributed topic experts to this broad industry initiative: nine coal mining companies, more than 80 experts, and more than 400 days of individual time for knowledge-capture workshops.

Jan 1, 2014

By V. Barranco, K. Yliniemi, A. Hubin, B. P. Wilson, D. Janas, M. Lundström, P. Hannula

Typical copper electrorefining electrolyte contains tens of grams of copper, some nickel and a wide variety of impurities. Some of these impurities comprise trace amounts of dissolved precious metals like Ag, Pd and Pt that currently are not fully exploited. This study presents an electrochemical method to recover precious metals via a combined electrodeposition-redox replacement (EDRR) process, where energy is used only to deposit copper during the ED-step, while the RR-step relies on the spontaneous replacement of copper by the precious metals (i.e. cementation). In order to conduct the recovery successfully, process parameters such as deposition potential (EDE), deposition time (tDE), redox replacement time (tRR) and the number of cycles (n) was adjusted. Investigations performed in synthetic electrolyte (40 g/L Cu, Ag = 10 ppm) proved the possibility to recover a high purity silver. Short deposition times (tDE) were found to result in small Cu particles that provided a suitably high surface area for silver cementation. In addition, experiments performed in real industrial electrolytes containing 44 g/L Cu and 54 ppb Ag (Boliden Harjavalta, Pori), demonstrated that EDRR could attain Ag recoveries of between 46–67% in an energy efficient, additive-free manner. INTRODUCTION The raw materials used in the state-of-art primary and secondary copper smelters contain mainly base metals, but also notable amounts of Ag, Pt and other precious metals. These valuable metals distribute mostly into the copper matte during the pyrometallurgical treatment (Tirronen et al., 2017) and end up into the cast anodes. During the electrorefining stage, metals more noble than copper such as gold and platinum, are not dissolved but enrich into the anode slimes. In contrast, silver may dissolve slightly and thus, minor chloride addition is used to retain silver in the slime as sparingly soluble AgCl. Moreover, other metals less noble than copper may also dissolve, such as nickel. Therefore the electrolytes used in electrorefining typically contain substantial amounts of copper, nickel and even arsenic as well as minor metals such as antimony and bismuth. In the Boliden electrorefinery these were reported to be in the magnitude of 51.2– 60.4 g/L of Cu, 10.9–15.8 g/L Ni, 7.2–15.9 As, 0.2–0.4 Sb and 0.1–0.4 Bi with an associated sulfuric acid concentration of 139–155 g/L (Lehtiniemi et al., 2018). Copper is the most noble of the dominating base metals in the electrolyte and is thus deposited on the cathode as 99.99% purity LME-A grade. Anode slimes are collected and subjected to precious metals treatment e.g. via pressure leaching—selenium recovery— Doré smelting—Ag refining—Au/Pt/Pd leaching and reduction process (Ludvigsson & Larsson, 2003). The Pori refinery, operating in Finland since 1941, not only produces 133 000 t Cu cathode and 2300 t nickel sulphate annually but also 66 t silver, 4.6 t gold and palladium and platinum (in year 2017).

Jan 1, 2019

By L. O. Thomas

BROADLY, Yukon is divisible into three physiographic provinces which are extensions of the similar divisions in British Columbia that are there known as the Coastal system, the Interior system, and the Rocky Mountain system. South of Yukon to about the 50th parallel of latitude, the Coastal system consists solely of the Coast range, which, in Yukon, passes behind the St. Elias range and for the remainder of its course constitutes the most easterly portion of the Coastal system. The extension, in Yukon, of the Interior system of plateaus and mountains of British Columbia is commonly referred to as the Yukon plateau, and the extension of the Rocky Mountain system as the Mackenzie Mountains system. The Coast-Range province is largely made up of granitic intrusives; the Mackenzie Mountains province of folded sediments; and the intervening Yukon Plateau province of ancient metamorphic rocks, folded sedimentary rocks, volcanics, and intrusives. Almost the entire area dealt with in this article was subjected to glaciation and, in those parts where its full effect was experienced, the valleys were invaded by vast masses of ice which transported and scattered the stream gravels, with their gold content, so that, even where gold still remains in the old stream channels, it has become so buried under boulder clay and other glacial accumulations that it is, in most places, difficult to find, and, when found, may prove very expensive to mine. Most of the present rivers have done little more than cut new channels in the glacial debris, touching only here and there upon the subjacent rocky floor. The territory in Yukon adjacent to the section of the Alaska highway between Watson and Teslin lakes is for the most part unknown both topographically and geologically. From Teslin to Kluane, the highway travels a fairly well-mapped part of Yukon, but beyond that point, until White river is reached, the geology of the adjacent country has, largely, yet to be determined, particularly on the north side of the highway.

Jan 1, 1943

By J. D. Bateman

Introduction The lifting of restrictions on the development of radioactive mineral deposits by private individuals has re-opened the search for uranium in Canada to a large body of professionally trained prospectors. The entry of private capital and experienced prospecting techniques into the search for radioactive minerals has been enormously stimulated by the atomic developments of the past several years; and we can now look forward to the discovery of new productive sources of uranium. The rate of new discoveries will, how ?ever, depend on the effectiveness of the methods used. The large number of new pitchblende occurrences reported within the past several months is largely a measure of the energy with which the portable Geiger-Müller counter has been applied in the field. The counter is simply a 'radio' receiver tuned to one of the products of spontaneous atomic disintegration that is characteristic of all radioactive materials. Its effective use depends largely on how it is applied under the various geological and topographical conditions that ma y be encountered, and also on an understanding of its limitations. Extensive geological information relating to the occurrence of radioactive minerals in Canada has been accumulated during the past several years, and it is now possible to define in a general way many of the geological formations in which pitchblende and related minerals are likely to occur. Furthermore, prospecting can be localized in those parts of the favourable formations that offer the greater promise of containing commercial deposits. In this selection, the Geiger counter is the most useful tool available to the prospector for the actual detection of radioactive materials. As an example, an area of two square miles in the Northwest Territories, within which about a dozen pitchblende occurrences had been found over a several year period by conventional prospecting methods, yielded more than forty-five additional discoveries by application of the Geiger counter. Yet earlier attempts at prospecting this area with the counter had failed, due largely to faulty instruments and lack of experience in field application. The limitations of the counter are very considerable; but, when they are recognized, there is no more useful tool for the discovery of radioactive ores. It was not until 1944 that a practicable portable counter was developed, and then only by co-operation in the field by geologists and physicists. Officers of the Geological Survey of Canada working with physicists of the National Research Council brought about the development of the modern counter.

Jan 1, 1949

By Barbara A. Filas

The IFC goal is to promote private sector investment in developing countries which will reduce poverty and improve people?s lives. The developing country goal is to promote health, education and employment opportunities that improve their economies and their standard of living. The mining company goal is to Promote successful ?triple bottom line? mining projects that will grow shareholder equity

May 1, 2002

By Helge B. Wurst, Michael P. Cipold, Jan F. Bachmann, Claus C. Bachmann

"In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink-float analysis. Time, cost and safety aspects of the sink-float method have prompted the search for a new approach for establishing separation performance criteria, especially as performance levels of separator plants can be maximized if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes readily available. The new method to establish washability and associated performance information utilizes at least two measurement technologies concurrently: single energy x-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy x-ray transmission and image processing. The value of the collected data increases considerably if the washability data were additionally available in time to be considered in the control of the process plant. The incorporation of an automated washability monitor gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested with a range of sample with different densities, varying from 1 g/cm³ (coal) to 5 g/cm³ (iron ore).INTRODUCTIONWashability of minerals like coal and iron ore is expressed by a curve or graph showing the results of a series of float-and-sink tests. Several of these curves are drawn to illustrate different conditions or variables, usually on the same axes, thus presenting the information on one sheet of paper. Washability curves are essential not only for the design but also for the operation of preparation plants.In determining the washability analysis, particle density is the underlying feature of all washability curves. Conventionally, the particles are separated into density fractions by immersing them in fluids of a predetermined density followed by skimming of those particles that stay afloat. The particles remaining afloat thus have a density lower than that of the fluid they were subjected to. The particles that remained at the bottom of the fluid container thus had a higher density higher than that of the fluid. By progressively increasing, for example, the density of the fluid and immersing the remaining particles so as to be able to skim the next density fraction, the particles would be fractionated into density groups. The liquids used range from aqueous solutions to organic liquids to suspensions. Unfortunately the liquids used for this separation process are often toxic and expensive. It stands to reason that a new method of determining washability is sought."

Jan 1, 2016

By W. J. Wright

Summary Statement The following notes on the geology of the Grand Lake coalfield are intended to be introductory to a second paper being read at this meeting, which paper will describe the earlier and the more modern mining methods. The coal industry of the Grand Lake coalfield is centred chiefly within a three-mile radius of Minto, but minor operations are dotted over an area of approximately 50 square miles extending easterly to the vicinity of Chipman and Coal Creek (see Figure 1). The coal comes from one seam of Pennsylvanian age. The seam varies in thickness from 16 to 30 inches and lies almost horizontal at depths of 0 to 125 feet. It has been mined and prospected over an area of approximately 150 square miles, but in a portion of this area the commercial possibilities have been destroyed by erosion. The industry is the oldest of its kind in North America, but it did not at tract particular publicity until about 1914. Since that date, mining methods have improved and the output has rapidly increased until, in 1934, it amounted to 271,335 long tons, and furnished employment for about 1,000 men (1). Approximately 73 percent of this amount was produced by the Minto Coal Company, the Miramichi Lumber Company, the Avon Coal Company, and Welton and Henderson, and 25 per cent by the Rothwell Coal Company, Harvey Welton Limited, G. H. King, the Reade Construction Company, and the Newcastle Coal Company. The remainder was produced by J. W. Carter, G. D. Crossman, T. H. Swift, C. S. Yeamans, and several other small operators. The coal is won by underground mining, except in the case of the Reade Construction Company, and a minor operation by Ashfield and Pieton, who have employed open stripping. It is mined only as required to fill definite orders, and is loaded directly into cars for shipment. In 1934, the larger mines did not operate full time, and the production could easily have been increased if markets had been available. The coal is sold in four grades: screened or lump, run of mine, slack, and stripping. The chief market is with the railways and commercial plants, with a fair amount for domestic purposes.

Jan 1, 1935

By H. C. Horwood

INTRODUCTION THE Argosy Gold Mines, Limited, which joined the ranks of active Ontario gold producers during the summer of 1936, holds a group of 21 claims on Casummit lake, in the Patricia portion, district of Kenora, northwestern Ontario. The Company is developing and mining goldbearing quartz veins that occur in a series of greywackes and slates of probable Keewatin age. The writer made a geological examination of the property and the surrounding area for the Ontario Department of Mines during the early part of the field season of 1936. This paper is a report on the general geology, structure, and ore deposits at the mine and is based almost entirely on data compiled during the examination. HISTORY Mineralization was first discovered on the property in May, 1929, by A. F. Hewitt, who, with J. A. Borthwick, decided that the country had prospecting possibilities and commenced work in April. Mr. Hewitt staked, and with his partner, J. Ziyone, still holds the group of claims lying immediately east of the present Argosy holdings. Mr. Borthwick staked six claims, K.R.L. 9,681 to 9,686, inclusive, adjoining Hewitt's on the west and later added claims K.R.L. 9,733 to 9,740, inclusive, to his holdings. F. Fiskness, who was also prospecting in the region, discoveted No. 1 vein on Borthwick's claims, and with his two partners, L. Parth and H. Jones, staked claims K.R.L. 9,758 to 9,763, inclusive, to the northwest of Borthwick's and Hewitt's ground. In July, 1929, the Casey Mountain Operating Syndicate, which held ground to the northwest, secured an option on Borthwick's claims. The Fiskness-Parth-Jones property was added in January, 1930, to protect the west dip of the veins. During the winter of 1930-31, the veins were explored by diamond drilling, No. 2 for a length ?of 900 feet and a vertical depth of from 51 to. 375 feet? and No. 3 .t~ a slope depth of 175 feet. I~ August, 1.931, after the msrallat10n of a miming plant, the Casey Summit Gold Mmes, limited, was incorporated to take over the property from the Syndicate. The Maple leaf Mines optioned a controlling interest in the stock in August, 1933, and on September 17th, 1934, brought a 50-ton amalgamation mill into production. From early in October to December 27th, 1934, when the mill was closed down, 4,094 tons of ore were treated to yield 887.89 ounces of gold and 87 .26 ounces of silver( ! ).

Jan 1, 1937

By J. F. Shirley

"Very seldom, if ever, is a molybdenite by-product plant operated exactly the way the process design engineer visualizes it. The best thing the design engineer can do is provide a sound, basic circuit with enough room and flexibility in order that the operating staff can make the necessary modi fi cations to optimize the process. The plant, with minor modifications, should be capable of handling more than one process. This is especially true when the client is having the plant designed for a new process.The writer would like to propose the following ten ""rules-of thumb"" for designing by-product molybdenite plants where the molybdenite is floated out of a copper concentrate. The term rules-of-thumb is used, because there are probably valid reasons for not using one or more of them in a particular plant design. In fact it was 1980 before the writer was all owed to start up a plant where all of these rules were honored in the plant design. This was after 19 years of experience in the design of molybdenite by-product processes and plants. The main reasons for not following the rules are available capital, available space, and the client's experiences based on pilot plant and laboratory test results."

Jan 1, 1981

By Tim Deans

This paper will address methods to manage hydraulic hose and coupling inventory so that parts will be available to build assemblies for the vast majority of equipment with as little inventory as possible. Topics also to be covered will include some basic hose assembly tagging techniques that will help keep equipment running by tracking problem hoses and building ?band aid? kits, having problem hoses premade in stock, and inventory usage tracking (one of the biggest problems for any inventory manager is knowing which couplings have been used so they can re-order). Cradle to grave tracking of hydraulic and industrial hoses insures reliable service of vehicles and ethical disposal of old hoses and couplings. With accountability for disposal of hose products that may contain chlorine (neoprene tube material in some hydraulic hoses) and carbon black that will be scrutinized more closely in the future, a proactive approach should be adopted in order to minimize maintenance facility problems.

Aug 1, 2013

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Abstract-Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-chalcopyrite core - interlayered pyrite-sphalerite-galena (Pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyrite­ quartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone 1) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (Il and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone 1, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F1 fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By K. Chattopadhyay

Fluid flows in metallurgical reactors play a vital role on liquid metal cleanliness for both ferrous and non-ferrous metallurgy. Thus, it is absolutely critical to understand different fluid flow mechanisms, and the use of computational methods to model the complex non-isothermal, turbulent, single- and multiphase-flows, has to be appreciated. The present case study emphasizes on controlling the flow of liquid steel in a tundish and enhancing liquid metal cleanliness. CFD modeling was used to build a robust mathematical model, and effects of flow control furniture and non-isothermal conditions were analyzed. The mathematical model was validated against water model experiments. Parameters that were conducive for inclusion removal were identified and implemented in the plant. Some flow control devices could increase inclusion removal to a great extent compared to the existing configurations. In cases, where a hot ladle was poured into a relatively cooler tundish, inclusion removal was better, whereas results were catastrophic in cases where colder liquid was poured from ladle to the tundish. Similar techniques can be applied for other liquid metals including light metals and non-ferrous metals.

Jan 1, 2015