Search Documents

By Barry J. Turley

With over 700 large electric-drive haulage trucks operating in Canadian mining today and over 3700 in mines worldwide, most aspects of electric drive are well known. Recently, however, extensive application of these trucks to down-hill hauling in mountain mining makes it vitally important that many of us better understand the operation and proper application of the dynamic retarding feature of these vehicles. This paper is an attempt to clear up misunderstandings on this subject, to suggest precautions that mining operators should take in comparing competitive retarding systems and to challenge equipment manufacturers to evolve improvements to the important aspect of system performance.

Jan 1, 1978

By Gobbs C., J. Lam

"The Eagle East project, accessed from the existing and operating Eagle Mine in the Upper Peninsula of Michigan, is an underground base metal project currently in execution by Lundin. This paper will provide an update on several aspects of ventilation including use of a twin-decline access, innovative airflow crossover arrangement and construction ventilation methodology. Integration into existing mine ventilation systems including construction methodology will also be covered. Performance benchmarks and lessons learned are discussed across these topics.INTRODUCTIONLundin has owned and operated the Eagle Mine since 2013. This hard rock underground mine is located in the upper peninsula of Michigan, USA. High-grade nickel ore is mined using sublevel open stoping mining methods and trucked to surface via haul ramp. The mine, having been in production for four years, is nearing the completion of the initial orebody. A satellite orebody 2,000 meters East of the current workings and approximately 900 meters below surface, was identified that could extend operations until 2023. In 2016, Lundin approved the Eagle East project and construction began in 2017 (Lundin Mining Corporation, 2017).Due to proximity to the existing mine, Eagle East will be both accessed and serviced from the existing Eagle Mine. Ventilation at the Eagle Mine uses two fresh air intakes with direct fired combustion heaters; one at the mine portal feeding fresh air into the ramp and one at a fresh air raise located near the Eagle deposit. The primary ventilation circuit is powered on the exhaust air side, with two 700 hp exhaust fans located at a single return air raise. Underground, fresh air is distributed through the main access decline and fresh air raise (FAR) to the production levels and controlled with mechanical regulators on the exhaust side. The exhaust air is collected through return air raises with a collector/transfer drift on 250 Level and then to the surface through a return air raise (RAR)."

Jan 1, 2019

By J. L. Collins

"Une recherche debutee en 1987 tente de cerner divers éléments ayant un impact sur la productivite miniére, de facon à améliorer la planification des operations souterraines. II a été possible de recueillir jusqu'à trente variables dans sept opérations minières differentes du Nord-Ouest québécois. Cette présentation rend compte de quelques résultats préliminaires obtenus à l’une d'entre elle. Entre autres, elle montre comment une association entre une analyse de régression multiple et un logiciel d'optimisation (OPTIMUL) peut servir à une application particulière de la planification d'une opération minière du Québec. Plus spécifiquement, la présentation montre comment une quantité appropriée de ANFO et de TOVEX peut maximiser la quantilé de minerai cassé, minimiser les couts de sautage ou encore minimiser les coûts d'explosifs par tonne de roche cassée, en se basant sur une série de contraintes réalistes provenant de la mine.ABSTRACTA study, underway since 1987, tries to evaluate factors affecting mines' productivity. Information has been collected from seven underground mines in Quebec and this paper shows preliminary results from one. In particular, it shows how a combination of multiple regression analysis, mathematical programming and a set of realistic mine constraints can be used for a particular application of mine planning. More specifically, the paper shows a parallel between maximizing production of tons of broken are, minimizing explosives costs or minimizing the costs of explosives per ton of broken are by an appropriate selection of ANFO and TOVEX quantity of explosives. Finally, the paper shows that minimizing the costs of explosives per ton of broken are is the best alternative to follow providing a special optimization program can be set up."

Jan 1, 1990

By Glenn Davis

In the world of large scale open pit mining, the majority of a mines operating cost is tied to the removal and transportation of the overburden waste material. Typically, many large haul trucks are employed to transport this overburden from each excavating face. The trucks transfer the waste material from deep within the pit to waste dumps on the surface incurring significant costs in operators, road construction and maintenance, vehicle maintenance staff and support facilities, fuel, tires, and spare parts, as well as the capital cost of the truck fleet itself. In addition, the haulage of the actual mined material carries similar operational costs. In both cases, these costs grow as the mine face advances and pit haulage distances increase. Reducing truck haulage is one key to the success of the Dual Truck Mobile Sizer (DTMS). Being the world?s first fully mobile truck dump station, transportation costs can be significantly reduced as the mine face advances. Furthermore, when used in conjunction with a shiftable face conveyor and a mobile overland hopper, substantial cost savings can be achieved. The mobility of the system allows for the considerable reduction in the haul truck fleet. Overall mine site emissions levels are greatly reduced by the fleet elimination, as well as keeping the majority of the hauls on a flat grade within the pit. Emission levels on a typical truck will dramatically spike as the angle and the length of the haul are increased. Moreover, comparing diesel engines versus electric powered conveyors to move the material contributes to the realized savings.

May 1, 2010

By P. E. Cavanagh

THIS REPORT is not intended to be a ?comprehensive survey of the steel industry in Europe. For the past ten years the Ontario Research Foundation has been interested in several developments in the steel industry in Europe which it was felt would be of particular interest in Canada and might possibly find application in this country. This is an account of the present status of some of these developments. The economies of steel making in Canada are somewhat different than in the United States because of the nature of the market and the relative costs and availability of such raw materials as metallurgical coke and electric power. There are cases in Europe where a great deal of effort and money has been spent in trying to make steel profitably by methods which take advantage of locally available and cheap raw materials by modifying standard practices. ln cases wl1ere the investigations have been successful and the data are available to allow translation of the results into Canadian conditions, it is felt that such information may be of great benefit in the future in Canada and at !east should be known to all those in the steel industry in this country. The field to be covered in this report only comprises the steps from concentration and treatment of iron ores to production of iron and is only concerned with those commercially operating processes well known to us and judged to be of present interest in Canada.

Jan 1, 1957

By K. M. Tompson, R. L. Armstrong, C. I. Godwin

"Tungsten skarn deposits on the Clea property in the Selwyn Mountains, Y. T., are related genetically to a quartz monzonite stock, about 500 metres in diameter at the surface. Lower Paleozoic sedimentary rocks are metamorphosed for a distance of 3 km from the stock. Tungsten-bearing skarn mineralization within the altered sedimentary rocks is of two types: sulphide-rich pods and calc-silicate beds. The most significant scheelite concentration is in calc-silicate beds near or adjacent to the quartz monzonite stock. Discordant K-Ar and Rb-Sr isotopic dates indicate that the stock is probably of early Late Cretaceous age, 94 Ma or slightly older, and that it cooled slowly. High initial 87Srl86Sr ratios and disequilibrium relationships between K-jeldspar phenocrysts and groundmass minerals in the porphyritic phase of the granitic rock , and between different granitic rock specimens, indicate contamination of crystallizing magma by old sialic continental crust which extends westward under the Selwyn Basin.This study is significant to regional tungsten exploration. Granitic rocks associated with tungsten deposits, in this part of the Canadian Cordillera at least, appear to have specific isotope characteristics that indicate they were generated at a specific time and in a particular way.IntroductionThe Clea tungsten skarn property (Fig. I) is owned by Canex Placer Limited, and lies in the Selwyn Mountains (Bostock, 1948) near the eastern margin of the Selwyn Basin (Wheeler and Gabrielse, 1972), Yukon Territory. The property covers a 20-square-mile area centered near latitude 62°47 ' north and longitude 129°52' west, and is accessible by helicopter. An airstrip and the terminus of a summer-use gravel road at MacMillan Pass, Yukon, are about 20 miles to the northnorthwest.This paper deals mainly with the geochronemetry of granitic rocks from a stock associated with tungsten mineralization on the Clea property. We show that these rocks have specific characteristics that not only define the genesis of this stock, but also have significance for regional tungsten exploration around plutons in the Canadian Cordillera."

Jan 1, 1980

By B. McLaughlin

"The Penna shaft is the deepest single-lift shaft in North America. Agnico-Eagle started sinking the Penna shaft in 1995 with a hoisting plant capable of hoisting 1800 t/d from a 2240-m deep shaft. Exploration success at depth led to the replacement of the existing double drum hoist by another double drum hoist capable of hoisting 7000 t/d. The use of another double drum hoist, instead of a Blair multi-rope winder, to hoist 24.5 t skips was only made possible by lowering the safety factor.This paper describes recent experiences at Penna and in South Africa, and examines the possibility of extending the double drum hoisting system to a depth of 3 km. IntroductionThe original Penna production hoist was a 4.88 m (16 ft) diameter double drum and single clutch machine. Béliveau (1996) and Scott (1996) have described this hoisting plant. In 1998, a decision was made to increase mining capacity from 1800 t to 4500 t of ore per day from the shaft bottom. Final capacity had to include an allowance of 1800 t of waste per day for future capital projects. While daily capacity was to be 6300 t, it would, by taking into account the different rock densities, be equivalent to hoisting 7000 t of ore.The steps taken to lower the safety factor were presented by McLaughlin and Scott"

Jan 1, 2004

By J. L. Nebreda, Z. Fan, J. B. Patel

"A380 alloy has been widely employed to produce thin-wall components via high pressure die casting (HPDC). During HPDC processing, there is a significant problem of property variation even with the very stable and precision automated casting procedure. The enlarged variation lowers the component performance and affects the steady and uniform property distribution along the whole component. In this study, high shear melt conditioning technology was developed and applied to the melt prior to pouring into the shot sleeve. Experimental results show that with application of intensive melt shearing, the variation of elongation was decreased from 21.8to 13.9%, and yield strength variation was reduced from5.5to 3.6%. The improved property variation is attributed to enhanced nucleation both in shot sleeve and the die-cavity, and to the improved distribution of porosity and secondary phases as a benefit of high shear induced grain refinement. With application of high shear, large number of the Spinel phase (MgAl2O4) particles with double size distribution in average diameter of 80and 300nm were formed. Due to the good orientation relationship and small misfit between alpha Al and MgAl2O4, the particles act as the effective nuclei in shot sleeve and die cavity, respectively.INTRODUCTIONA380 alloy had been widely used for produce automotive components by cold chamber high pressure die casting(HPDC) processing, due to its relative good mechanical properties and cast ability performance, and more important most of A380 ingots were produced by recycled Al alloys. Therefore, to promote utility of A380 will contribute to reducing emission of CO2and to the lightweight of automotive industry as well. When cold chamber HPDC was employed to produce the components, the mechanical properties of A380 alloy always have a distribution range (named variation herein), or in other words the properties were not stable. The reason was ascribed to the typical solidification characteristics occurred in HPDC processing. During HPDC processing, there are three steps of melt movement. The first step is that the melt was poured into shot sleeve at temperature of about 680°C, in which shot sleeve was preheated by few shots of melt filling, or by heater. During step one, the first solidification of melt was happened in shot sleeve and about 20% solid made of coarse a-Al grains was formed(Li, Xiong, & Guo, 2016).Such kind of grains will retain in the final products and deteriorate the properties variation. The second step is that the melt was forced moving forward slowly by plunger at about 0.2–0.3m/s until the liquid melt front to the inner gate of mold. The third step is that the melt moved very fast to complete the filling of die cavity and refilling the solidification shrinkage by fast movement of plunger about 2–3m/s. The second solidification was occurred in die cavity and fine a-Al grains will be formed by high cooling rate at about 500–1000°C/s. From the solidification point of view, the grain size was dominated by nucleation and growth. When HPDC was employed to produce components, the melt quality becomes the priority factor to control the solidification process as the other casting parameters were kept at the same."

Jan 1, 2018

By J. R. Parga T., P. J. Valenzuela G., L. S. Quiroz C., P. Guerrero G., J. L. Valenzuela G.

"Pressure oxidation is a hydrometallurgical pre-treatment process used for refractory auriferous sulfide ores. In the work reported here, a refractory pyrite ore sample from the Mulatos mine, Sonora, Mexico was characterized. The sample was subjected to atmospheric cyanidation, and simultaneous pressure oxidation and cyanidation under different conditions of temperature and pressure. The mineral characterization showed that pyrite is the main species in the sample. The gold extraction tests were carried out in an 1-litre Parr pressure vessel at a temperature range of 90-120 °C, a pressure range of 87.5–150 psi (using oxygen), and a cyanide concentration range of 0.8-1.2 %wt. The gold extraction results showed that diffusion through product layer is the rate controlling step.INTRODUCTIONIn hydrometallurgical precious metals extraction, the most commonly used process is sodium cyanide leaching, as shown in the next reactions involving gold and silver (Fleming, 1992; Marsden & House, 2006):4Au(s) + 8CN- (aq) + 2H2O(l) + O2(g) ? 4Au(CN)2 -(aq) + 4OH- (aq) (1)4Ag(s) + 8CN- (aq) + 2H2O(l) + O2(g) ? 4Ag(CN)2 (aq) + 4OH- (aq) (2)“Refractory” auriferous ores or concentrates often contain gold and silver locked inside other sulfide phases such as pyrite. This renders cyanidation ineffective, so oxidative pre-treatments are used in order to convert the sulfide minerals into porous oxide minerals and make cyanidation work more efficiently. Reaction (3) shows the oxidation of pyrite in alkaline media and the formation of the porous oxide (Koslides & Ciminelli, 1992):2FeS2 (s) + 15/2 O2 (g) + 8H- (aq) ? Fe2O3 (s) + 4SO4 2- (aq) +4H2O(l) (3)A process of simultaneous chemical pressure oxidation and cyanide leaching for a flotation concentrate produced in the mine of Bacís, Durango, in Mexico, gave good results (Parga et al., 2007). In the study presented here, it was intended to use this treatment for a refractory pyrite mineral from the Mulatos mine in Sahuaripa, Sonora, Mexico, modifying variables such as pressure, temperature and cyanide concentration to find the best conditions for oxidation and leaching."

Jan 1, 2012

? CONSTRUCTION AND MINING COSTS ARE HIGH IN THE ARCTIC ? VERTICAL KIMBERLITE PIPES WITH HIGH STRIP RATIOS ? SITE SPECIFIC GEOMETRIC CONSTRAINTS ? OPEN PIT FOLLOWED BY UNDERGROUND MINING ? HIGH KIMBERLITE UNIT COSTS TRACK INSTALLED ON PIT WALL ? INTENDED TO REPLACE MAIN HAUL RAMP ? 5 MIN HOIST CYCLE TIME ? KEY ADVANTAGES - REDUCED CYCLE AND STRIPPING RATIO ? TECHNOLOGY EXISTS IN OTHER APPLICATIONS

May 1, 2003

By J. J. Barakso, C. Tarnocai

This paper outlines a method of testing for the mercury content of rocks, soils and plants. Techniques of sample collecting are described and the analytical procedures outlined. Examples are given of mercury determinations in two known mineralized areas in British Columbia - Copper Mountain Mines and Pacific Nickel Mines.

Jan 1, 1970

By H. Staton, XPS Consulting & Testwork Services, T. Deng, M. Kelvin

"Lundin Mining’s Eagle Operation, located in Marquette County, northern Michigan consists of a mine and concentrator that processes a Ni-Cu-(PGE) ore. Mine production began in 2014 and is expected to achieve production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year. The ore is trucked to the Humboldt Mill, where both a Ni and Cu concentrate is produced.XPS Consulting & Testwork Services (XPS) has assisted the team at Eagle since 2013. Prior to start up, the ore was piloted at the XPS lab in Sudbury, Ontario to demonstrate the concentrator flowsheet and establish flotation operating strategy. XPS consulting metallurgists worked closely with the Eagle team during the commissioning of the plant providing troubleshooting, sampling, metal balancing expertise and support. Finally, a series of monthly composites over a 6 month period was submitted for mineralogical characterization to assess plant performance, identify opportunities for improvement and to provide a baseline for the future operation.Lundin’s investment to test the ores ahead of mining and to team with XPS’s experienced mineral processing engineers to help commission the plant has led to the plant achieving concentrator production targets shortly after startup. The commitment to training and implementation of best practices, and a culture where ongoing testing is the norm, puts the Eagle Operation on sound footing for future operation.INTRODUCTIONLundin’s Eagle Mine is a subsidiary of Lundin Mining located in the upper peninsula of Michigan. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 2 hours to the Humboldt mill.The ore is an ultramafic hosted high grade Cu Ni deposit and exists as either massive or semi massive sulphides. The high resource grade of Cu (2.49%) and Ni (2.93%) make this a valuable ore source. (Owen & Meyer, 2013) A metallurgical team was put together by Lundin to ensure the mill was designed and commissioned to optimize metallurgy in the shortest time from this valuable deposit. The commissioning plan targeted commercial production by Q1 2015."

Jan 1, 2016

By Graham Davey

"Ultrafine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The recent development of industrially proven and cost efficient technologies for ultrafine grinding has opened up another processing option for the treatment of finegrained metalliferous and refractory gold ores. The current commercial designs are variations of stirred mills used in the industrial minerals sector for the past 30 years. For the purposes of this paper ultrafine grinding is considered to be P80 of less than 15 microns.Attrition milling to fine grind sizes presents some challenging issues relating to scale-up including the dearth of information on the quantitative impact of feed and operating conditions, as well as the precise and accurate measurement of particle size distributions. Two examples from recent installations will be analyzed including Thalanga Copper and Century Zinc Mines. Both have diverse grind size targets for the SMD, yet both have realized significant metallurgical gains."

Jan 1, 2002

By R. England

"This paper describes the objectives and design parameters for the operation of a computerized In-The-Hole (I. T.H.) Drill. The principal objective is to add computer control to an Inco 00-60 I. T.H. (CMS-CD-90) drill in order to drill holes with greater accuracy. The computer provides control of the angle of the hole by maintaining the orientation of the drill head, and optimizes the straightness of the hole by maintaining a constant force on the drill bit.The second objective is to provide the greatest degree of operational automation, so the objective outlined above can be accomplished with a minimum of operator intervention.In order to provide full operational automation it was necessary to also provide the capability for the computer to add and remove drill rods. To accomplish this, a rod-handling mechanism consisting of a rod storage rack and rod manipulator arms was used.IntroductionMining machinery that lacks automatic control has been found to show a high degree of variation in work output and performance quality when operated by different personnel. Differences in operator attitude, judgment, and skill are reflected directly by production statistics. The addition of automated control has the potential for considerable improvement in machine life and performance. Even with a more acceptable mine environment and much safer conditions than ever before, situations still exist where it is preferable to remove personnel for reasons of safety as well as productivity. Typical advantages of such situations are automated skip loading and hoisting, and the use of remote control load-haul-dump units exposed to open stopes.Other cases arise where heavy work is required under conditions where lighting is poor, floors are slippery, noise levels are high and dust and oil mist exist in the atmosphere. I.T.H. drilling is carried out under such conditions and is one operation where automation can easily be justified."

Jan 1, 1987

By A. Luszczkiewicz

This paper presents the beneficial effects of non-oxidative leaching of final and intermediate copper sulfide concentrates with sulfuric acid prior to the final cleaning stage of flotation. This unique process, combining leaching and flotation, appears to be advantageous for difficult-to-treat carbonate-bearing Polish copper ores, such as those processed in copper concentrators at KGHM Polish Copper. It was shown that after the chemical decomposition of about 70 % of the total carbonates naturally present in the flotation feed, a considerable enhancement of subsequent flotation results (both grade and recovery). The resulting products of non-oxidative leaching are solid hydrated calcium sulfate (gypsum), soluble magnesium sulfate and gaseous carbon dioxide. The beneficial effect established by the laboratory leaching tests was subsequently confirmed during a pilot plant operation treating final copper concentrate and a problematic intermediate concentrate at the Lubin concentrator.

Jan 1, 2007

By Jean Cayouette

"In 1995, Louvicourt Mine started one of the first paste backfill operations in Canada. From 500,000 tonnes in 1995, the annual paste backfill tonnage produced reached 800,000 tonnes in 1999. The maximum throughput of the surface plant (including binders) is 3,50Ot/d with a final density of 75 to 76% solids which gives a slump of 15 to 17cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders consisting of a mixture of 20% cement and 80% ferrous slag. In certain stopes, the binder ratio may vary from 2 to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.INTRODUCTIONLouvicourt Mine is operated by Aur Resources Inc. which owns 30% of the shares. Its partners are Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corporation (25%). The mine is located in the north-west part of Quebec, about 600 km north of Montreal and about 25 km east of Val d’Or. The mine commenced commercial production in July 1994."

Jan 1, 2002

By Anton Sizo, Alexey Klyashtorin

The Gunnar uranium mine operated from 1953 to 1961 on the shore of Lake Athabasca, in 1964 the site was abandoned, and the mine pit flooded. In 1981, the pit was found to be stratified with a chemocline at ~70 m by a sharp change in conductivity and TDS. The uranium concentration was ~700 μg/l on the surface, 320 μg/l at 50 m, and 2,900 μg/l at 110 m. The Ra-226 concentrations were 0.1, 0.06, 0.12, and 0.4 Bq/l. By 2017, the chemocline was ~60 m deep. The highest uranium concentration was 1150 μg/l and the lowest concentration (220 μg/l) was attributed to the chemocline. In the deeper column, the uranium content varied around 750 μg/l. The uranium distribution down the pit profile was aligned with DO, ORP, and TDS. Ra-226 averaged to ~0.4 Bq/l, Ra-226 and uranium profiles were inversely related with the respective maximum and minimum attributed to the chemocline. The uranium and radium amount accumulated in the pit by 2017 was 3,420 kg and 2,163 GBq, respectively. The uranium and radium apparent accumulation trend estimates to 64 kg/y and 41 MBq/y, respectively. A stable chemocline and no concentration gradients in the other parts of the pit suggest that the contaminants are unlikely to inflow from the bottom opening or outside the pit, but rather are mobilized from the pit walls. The contaminants are not in a steady state, and concentrations of both uranium and radium are likely to increase slowly in the future if no remediation occurs.

Jan 1, 2020

By R. C. Bryce

"Selbaie is located northwest of Joutel, in what is known as the fourth east-west volcanic sediment group in northwestern Quebec. The main metals produced are copper and zinc, with important contents of both silver and gold. Production comes from an open pit mine on the A-I zone and from two underground mines on the B zone and the A-2 zone. Each mine gave rise to important capital investment programs for construction and mine development, all of which were managed and staffed with company-hired, non-union personnel. Production from all sources now exceeds 7000 tonnes per day, with a workforce of540 regular employees. Of particular interest technically is the high recovery of B zone reserves underneath 40 m of overburden cover, the low-cost capital development of the A-2 zone, the computerized control of open pit mining, and the successful copper-zinc separation of the A-1 zone ore. Due to the low grades of the mineral deposits, efficiency in all aspects of the production process, is essential to the success of the operation.LocationThe Selbaie Mine is located 82 km northwest of the locality of Joutel in northwestern Quebec (Fig. 1). Access to the mine is by an all-weather road, 32 km of which is paved. A second road access to the site is via La Sarre, 134km to the southwest. Employee access, materials transport and haulage of copper and zinc concentrates take place over both of these roads."

Jan 1, 1990

By R. B. Allen, E. E. N. Smith, B. C. MacDonald

"LocationTHE MAIN PROPERTY and townsite of Eldorado Mining & Refining, Limited, Beaverlodge Operation, is on the north shore. of Beaverlodge lake, •about seven miles north of the deserted town of Goldfields on lake Athabasca, and four hundred and ninety air-miles equidistant from Prince Albert, Saskatchewan, and Edmonton, Alberta. Both Eldorado Airlines •and Canadian Pacific Airlines maintain scheduled flights from Edmonton to the 4,000-foot airstrip on the north boundary of the Company property. Bi-weekly flights are made by Saskatchewan Government Airways from Prince Albert. Men and priority freight are flown by Company aircraft direct from Edmonton. From June to-September, when the waterways .are ice-free, freight is carried by barge from the •railhead at McMurray, Alberta, down the Athabasca river to Chipewyan, and across lake Athabasca to• Bushell, the terminal on Black bay, lake Athabasca, a total distance of 265 miles.The Eldorado Operation has been connected by a 12-mile, all-weather highway to Bushell. Where the highway crosses the park-land along the Fredette river, the townsite, Uranium, is under construction to provide services to the uranium-producing district. Spur roads have been built to the Ace, Fay, Eagle, •and Martin mines of the Eldorado operation, and to the properties of Pitch-Ore Uranium Mines, Ltd., and Rix Athabasca Uranium Mines, Ltd."

Jan 1, 1954

By Gregory C. More O'Ferrall

Generally pillars in the Southern African hard rock tabular underground mining environment are designed using either empirical pillar design formulae or numerical modelling (analytical) methods utilizing the Hoek-Brown failure criterion. However, none of the pillar design methodologies employed takes cognizance of weak layers either within the pillar material or in the immediate foundation of the pillar. Over the past few years, the presence of a weak layer either within the pillar material or within the immediate foundation of the pillar has resulted in the closure of one platinum mine (Everest Mine), closure of one chrome mine (Wonderkop Chrome) and large-scale instability in a couple of chrome and platinum mines in South Africa and Zimbabwe. A study has been initiated to better understand the failure mode and strengths of the pillars where pillar failure associated with weak layers occurred. Owing to the infancy of the study into the failed pillar strength and failure mechanism, the purpose of this paper is to highlight the circumstances that led to the collapse of mining sections and a shaft, and the difficulty associated with designing pillars in the Southern African chrome and platinum mining operations.

Jun 1, 2012