Search Documents

By J. Esson, R. A. D. Pattrick, M. K. Nimfopoulos, D. A. Polya, K. M. Michailidis

"Abstract-Economic Mn-oxide ore deposits of commercial grade occur in the Rhodope massif near Kato Nevrokopi in the Drama region, Northern Greece. The Mn-oxide mineralization has developed by weathering of continental hypogene rhodochrosite-sulphide veins. The vein mineralization is confined by tectonic shear zones between marble and metapelites, extending laterally into the marble as tabular, pod or lenticular oreshoots (up to 50 m ?? 20 m ?? 5-10 m). Supergene oxidation of the hypogene mineralization led to the formation of in-situ residual Mn-oxide ore deposits, and secondary infills of Mn-oxide ore in embryonic and well developed karst cavities.Whole rock geochemical profiles across mineralized zones confirm the role of thrusts and faults as solution passageways and stress the importance of these structures in the development of hydrothermal and supergene mineralization at Kato Nevrokopi. Three zones are recognized in the insitu supergene veins: (A) a stable zone of oxidation, where immobile elements form (or substitute in) stable oxide mineral phases, and mobile elements are leached; (B) a transitional (active) zone in which element behavior is strongly influenced by seasonal fluctuations of the groundwater table and variations in pH-Eh conditions; and (C) a zone of permanent flooding, where variations in pH-Eh conditions are minimal. Zone (B) is considered as the source zone for the karst cavity mineralization. During weathering, meteoric waters, which were CO2-rich (PCO2 ~10-3.8 to 10-1.4) and oxygenated (fO2 ~10-17 for malachite), percolated downward within the veins, causing breakdown and dissolution of sulfides and marble, and oxidation of rhodochrosite to Mn-oxides. Karst cavity formation was favored by the high permeability along thrust zones. Dissolved Mn2+ was transported into karst cavities in reduced meteoric waters at the beginning of weathering (pH~4-5), and as Mn(HCO3)2 in slightly alkaline groundwaters during advanced weathering (pH~6-8). Mn4+-oxide precipitation took place by fO2 increase in ground waters, or pH increase by continuous hydrolysis and carbonate dissolution. In the well developed karst setting, some mobility of elements occurred during and after karst ore formation in the order Na>K>Mg>Sr>Mn>As>Zn>Ba>Al>Fe>Cu>Cd>Pb."

Jan 1, 1997

By Michael Harley, E. Guy Charleworth

"Bedding-parallel thrust-hosted gold veins are developed in the Sabie-Pilgrim's Rest goldfield, eastern Transvaal, South Africa. The reefs display a complex history characterized by temporally and spatially overlapping events of similar mineralization and deformation. Recognition of the episodic reactivation of these low angle (5° to 10°) thrust faults implicates high fluid pressures (equalling or exceeding lithostatic pressures). Geochemical constraints limit the amount of fluid-rock interaction and the occurrence of transgressive mineralization within the Archaean granitoid basement suggests that the high pressure fluids originated at depth beneath the Transvaal Basin.Similarities exist between gold deposits of Sabie-Pilgrim's Rest and Telfer, Western Australia as well as Passagem de Mariana, Minas Gerais, Brazil. All deposits are sub-parallel to the enclosing bedding which is shallowly inclined. Furthermore, they are also hosted by contractional deformational structures and are clearly epigenetic in origin."

Jan 1, 1994

By Michael Harley, E. Guy Charlesworth

"Abstract - Bedding-parallel thrust-hosted gold veins are developed in the Sabie-Pilgrim's Rest goldfield, eastern Transvaal, South Africa. The reefs display a complex history characterized by temporally and spatially overlapping events of similar mineralization and deformation. Recognition of the episodic reactivation of these low angle (5° to 10°) thrust faults implicates high fluid pressures (equalling or exceeding lithostatic pressures). Geochemical constraints limit the amount of fluid-rock interaction and the occurrence of transgressive mineralization within the Archaean granitoid basement suggests that the high pressure fluids originated at depth beneath the Transvaal Basin.Similarities exist between gold deposits of Sabie-Pilgrim's Rest and Telfer, Western Australia as well as Passagem de Mariana, Minas Gerais, Brazil. All deposits are sub-parallel to the enclosing bedding which is shallowly inclined. Furthermore, they are also hosted by contractional deformational structures and are clearly epigenetic in origin."

Jan 1, 1994

By Beaumier. M., J. -P. Lalonde

"Les réultats obtenus dans les sols sur quatorze aires d'essai et six cheminements régionaux dans I'A bitibi-Témiscamingue indiquent clairement qu'il existe des variations régionales importantes dans les teneurs en éléments traces de l'horizon A1 formé sur l’épais recouvrement glacio-lacustre de cette région. Les anomalies obtenues correspondent à celles qui ont été décelées lors de précédents levés des eaux souterraines et du till de base.Selon les critères d'évaluation utilisés, treize des quatorze aires d'essai ressortent comme anomales dans Ie contexte abitibien; dix de celles-ci sont tres anomales. Ceci suggère fortement qu'un levé régional de sols, fondé sur une approche multi-éléments, identifierait entre 70 et 90 % des cibles géochimiques reconnues par des échantillonnages en profondeur. Les résultats d'un échantillonnage systématique effectué sur une région de 1000km2 viennent aussi appuyer cette hypothèse. Conséquemment, les sols formes sur les sédiments glacio-lacustres sont un médium très utile pour inventorier de grandes regions recouvertes par ce typ e de sédiments.L 'horizon A1 est Ie plus utile pour ce type de levé parce qu'i1 est facil e d échantillonner, qu 'it assure une plus grande constance du typ e de matériel échantillonne et qu'il contient des teneurs accrues.De multiples mécanismes de dispersion géochimique ont joué des rôles d 'importance variable pendant et après la mise en place des sédiments glacio-Iacustres. Les plus importants sont la pression hydrostatique, la diffusion chimique et électrochimique ainsi que la bio-accumulation. Si on veut progresser dans la connaissance de ce milieu complexe, on devra adopter une approche plus systemique tenant compte de I'interaction des mécanismes agissant dans l'environnement global avant, durant et apres Ie depôt du mort-terrain."

Jan 1, 1984

By J. Esson, R. A. D. Pattrick, M. K. Nimfopoulos, D. A. Polya, K. M. Michailidis

"Economic Mn-oxide ore deposits of commercial grade occur in the Rhodope massif near Kato Nevrokopi in the Drama region, Northern Greece. The Mn-oxide mineralization has developed by weathering of continental hypogene rhodochrosite-sulphide veins. The vein mineralization is con-?ned by tectonic shear zones between marble and metapelites, extending laterally into the marble astabular, pod or lenticular oreshoots (up to 50 m x 20 m x 5-10 m). Supergene oxidation of the hypogene mineralization led to the formation of in-situ residual Mn-oxide ore deposits, and secondary infills of Mn-oxide ore in embryonic and well developed karst cavities.Whole rock geochemical pro?les across mineralized zones con?rm the role of thrusts and faults as solution passageways and stress the importance of these structures in the development of hydrothermal and supergene mineralization at Kato Nevrokopi. Three zones are recognized in the in-situ supergene veins: (A) a stable zone of oxidation, where immobile elements form (or substitute in) stable oxide mineral phases, and mobile elements are leached; (B) a transitional (active) zone in which element behavior is strongly in?uenced by seasonal ?uctuations of the groundwater table and variations in pH-Eh conditions; and (C) a zone of permanent ?ooding, where variations in pH-Eh conditions are minimal. Zone (B) is considered as the source zone for the karst cavity mineralization. During weathering, meteoric waters, which were CO2-rich (PCO2~10-3.8 to 10-1.4) and oxygenated (fO2~10-17 for malachite), percolated downward within the veins, causing breakdown and dissolution of sul?des and marble, and oxidation of rhodochrosite to Mn-oxides. Karst cavity formation was favored by the high permeability along thrust zones. Dissolved Mn2+was transportedinto karst cavities in reduced meteoric waters at the beginning of weathering (pH~4-5), and as Mn(HCO3)2in slightly alkaline groundwaters during advanced weathering (pH~6-8). Mn4+-oxide precipitation took place by fO2increase in ground waters, or pH increase by continuous hydrolysis and carbonate dissolution. In the well developed karst setting, some mobility of elements occurred during and after karst ore formation in the order Na>K>Mg>Sr>Mn>As>Zn>Ba>Al>Fe>Cu>Cd>Pb."

Jan 1, 1997

By Jan W. Merks

"The settlements between mines and smelters are based on the mass of metal contained in concentrate lots. The mass of contained metal is a function of the wet mass of a lot, and its moisture content and metal grade while the variance of the mass of contained metal is a function of the same variables and their variances. Uncertainties in the measurement procedure applied to estimate each variable are quantified in terms of precision and bias. The absence of bias and an acceptable degree of precision are the keys to effective risk analysis and loss control.ISO Technical Committee 183-Copper, Lead and Zinc Sulfide Concentrates, has developed standard methods for sampling and weighing, estimating precision and testing for bias, the determination of mass loss on drying, the calculation of the mass of contained metal and its variance, and various analytical methods for major and minor metals. The variance for wet mass is calculated from the precision of the scale while the total variances of moisture and grade are estimated from pairs of interpenetrating primary samples. The variance of contained metal can be calculated either from mine data or from smelter data but the risk associated with the settlement is largely determined by the absence or presence of bias and the variance of differences between exchange assays.ISO/TC 183 does not deal with precision and bias for exchange assays but is developing guidelines to determine realistic splitting limits. Given that the exchange of assays between mines and smelters accounts for a large part of the risk associated with the settlement, precision and bias for exchange assays should be measured and monitored. The need for umpire services can be reduced by applying statistical quality control (SQC).Calibrating static scales, moisture balances and analytical balances, bias testing of sampling methods and sample preparation procedures, estimating the variance of a single variable or the variance of a function that a set of variables defines, and monitoring precision and bias for exchange assays, are the quintessence of metrology, the science of measurement, when applied in mining and metallurgy."

Jan 1, 1995

By C. H. Hitchcock

History In approaching the subject of diamond-drilling practice, a brief history of the origin and development of the diamond drill may be of interest. The use of black diamonds for boring holes in rock was discovered in 1863 by Rudolph Leschot, a French engineer. In 1864, he employed a diamond bit to bore holes for blasting purposes in the construction of the Mont Cenis tunnel between France and Italy. The method was introduced and developed in the United States in the late sixties. The first deep hole was drilled for coal in 1870, near Pottsville, Penn., by M. C. Bullock. This hole was seven hundred and fifty feet deep. It can be inferred that the diamond drill was introduced into Canada in 1871, when a bore-hole, known as Harper's bore-hole, was drilled for coal at Springhill, Cumberland county, Nova Scotia; and at the old Silver Islet mine, near Port Arthur, the diamond drill was in use as early as 1872. Diamond Drills While M. C. Bullock was developing the diamond drill for exploratory work, the Sullivan Machine Company, of Claremont, N.H., was developing the diamond channelers and gadders for quarry work. These quarry machines were very successful until the high price of black diamonds became prohibitive. In 1878, Albert Ball, chief engineer of the Sullivan Machine Company, designed the Sullivan diamond drill so well known today. The first of these drills went to the Lake Superior iron ranges. After 1880, use of the diamond drill expanded rapidly and spread to all parts of the world where exploratory work was being done. In recent years, the type of diamond drill has not changed much, but better material is going into its construction. Steel castings have replaced cast-iron. Ball and roller bearings are now used instead of brasses and babbits. Gun lubrication has eliminated the oil-can. These improvements make a drill that can be operated for long periods without expense for repairs.

Jan 1, 1933

"The Code was developed in 2004 through the Collaboration Agreement between Institution of Mining Engineers of Chile (IIMCh) and the Ministry of Mining (Chile) in Dec 2002. It is an amalgamation of current practices with respect to standards and procedures for exploration prospects, mineral resources, and reserves for the purpose of public reporting. Certification is required to prepare and issue information on mineral assets according to the guidelines that regulate the technical, economic, and environmental aspects that satisfy the conditions set by the Chilean capital and financial markets.The Mineral Resources Committee of the Instititution of Mining Engineers of Chile (IIMCh) is pleased to introduce theCode for the Certification of Exploration Prospects, Mineral Resources and Reserves which is the result of a Collaboration Agreement between the IIMCh and the Ministry of Mining established in December, 2002.This code synthetizes the present practice of the mining industry in regard to standards and procedures applied to exploration prospects, mineral resources, and reserves with the purpose of reporting publicly on financial instruments based on these mine assets in the capital markets. These standards follow general criteria already adopted and applied by capital markets in those countries characterized by a very dynamic and well developed mining sector such as Australia, Canada, Southafrica, United Kingdom, and others. The work done by the Mineral Resources Committee of the IIMCh has had the recognition of the Combined Reserves International Reporting Standards Committee (CRIRSCO) that leads the establishement of an international code in these matters. CRIRISCO is an entity formed by representatives of the countries previously mentioned, a representative of the Society of Mining Engineers of the UStates and a representative of the IIMCh. The Institution thanks the Ministry of Mining, the representatives of these Ministry in the Mineral Resources Committee, and specially the Minister of Mining, Sr. Alfonso Dulanto Rencoret due to the genuine support given to the IIMCh in the preparation of this Code.The Institution also thanks the Superintendencia de Valores y Seguros (SVS) because of the help given continuously to the Committee as well as by the interchange of opinions and suggestions received during the preparation of this document."

Jan 1, 2003

By J. A. Brothers, M. R. Foran

"AbstractThis paper reviews the progress made in the manufacture of hydraulic cement from iron blast-furnace slag by simply grinding the granulated material with other constituents. The influence of the chemical and mineralogical composition of the slag, the conditions of granulation, the manner of drying, and the fineness of grinding, on the hydraulic properties of the cement, is discussed. The effect of additions of lime, portland cement, and anhydrite, alone and in combination, on the physical and cementing qualities of the mortar and concrete made from Sydney blast furnace slag, is shown in tables of data and is reviewed in some de- tail. The work at the Nova Scotia Technical College has shown that a cement equivalent in every respect to portland cement can be made from basic blast furnace slag- by the us2 of certain quantities of portland cement as an activator.IntroductionBlast furnace slag is a potentially valuable material for the manufacture of hydraulic cement. It is a by-product of the manufacture of iron in the blast furnace, and is formed by the combination of the silica and alumina .of the iron ore with the limestone flux. The metallurgist terms a slag .acid or •basic according as the percentage of lime is less or greater than the percentage of silica plus alumina. The basic slags have the •more pronounced hydraulic properties."

Jan 1, 1950

By W. B. Boggs

Part 1 Originally, the copper produced at the Noranda ?smelter was shipped in the form of blister bars to the Laurel Hill refinery of the Nichols Copper Co., New York. In 1930 a refinery was built at Montreal East for the purpose of refining Noranda copper and copper from the Hudson Bay Mining and Smelting Co., at Flin Flon. After investigation of the probable costs of making anodes at Noranda and at Montreal, it was decided to make them at Noranda rather than to continue to make blister bars there. Fuel is a major item of expense in making anodes: and since less fuel would be required in making anodes from molten copper than in making them from blister bars, a lower anode furnace cost could be expected at Noranda than at Montreal. Further, the expense connected with making blister bars at Noranda would be eliminated. The cost of treating anode and wire bar furnace slags is a serious item in a refinery, and it was found that the cheapest method would be to ship such slags back to Noranda. With the anode furnace at Noranda, much less anode furnace slag would be made at the refinery. Against these savings which would be effected by making anodes at Noranda must be set the high operating cost of an anode furnace at Montreal, using only tank-room scrap and the Flin Flon copper. This furnace would be handling a comparatively small tonnage and would have a high cost per ton. The usual equipment for making anodes from. liquid copper consists of either a stationary reverberatory furnace or a tilting Tacoma-type furnace together with an anode wheel of the Clark or Walker type. The reverberatory type of furnace has been developed from the furnace used in the old Welsh process of smelting and refining copper, while the tilting furnace is a development of the holding furnace, which is essentially a Peirce Smith converter without tuyeres and provided with burners.

Jan 1, 1932

By D. S. Case

"Following a brief explanation of the land arrangements under the Alaska Native Claims Settlement Act, this paper will examine both a mineral exploration agreement and a mining development agreement negotiated between two large mining companies and two different Alaska Native institutions. One of the institutions is a village corporation involved with an exploration agreement and the other is one of the Alaska Native regional corporations, which is party to a mining and development agreement with Cominco Alaska for the development of the Red Dog lead and zinc mine.Special attention will be given to the factors to be considered when dealing with small aboriginal owners with few resources in the context of an exploration agreement, including development issues which must be considered early in the process. The paper will also discuss the unique royalty and taxation structures developed for the Red Dog Mine Agreement as well as environmental issues. The paper will also consider the ways in which the cultural and differing economic interests of an aboriginal owner and a large mining company have been accommodated in the both the exploration and development agreements"

Jan 1, 1998

By R. J. Hundermark, K. van der Merwe, L. R. Nelson

Taphole integrity is critical to all furnaces, but it is especially important in high intensity electric furnaces processing matte and metal of high superheat. Key furnace dimensions are the electrode proximity to the taphole, hearth sump below the taphole and the shape and location of the taphole in the furnace wall (e.g., circular versus rectangular furnace). In addition, electric furnace power density needs to be matched appropriately to any configuration to achieve operational reliability and furnace integrity. The role of furnace dimensioning is generically reviewed across many pyrometallurgical processes to explore potential impact on furnace taphole performance. Some empirical furnace dimensions and power density ratios of industrial furnaces are then compared to explore to what extent they may indeed influence taphole integrity.

Jan 1, 2015

By Orlando C. Gaspar

Abstract - The presence of fine-grained mineral intergrowths, the complex distribution of deleterious minor elements, and the variable base-metal contents in some assemblages commonly pose technical problems for the processing of volcanogenic massive sulfide ores. The beneficiation of most massive sulfide ores from the Iberian Pyrite Belt requires extremely fine grinding to liberation sizes of K80 = 15 µm to 25 µm. For several deposits, mapping of the ore types and metal zoning patterns has shown that the different ore types are distributed as ore lenses within the massive sulfides. Mineralogical, textural, and metallogenetic studies have provided an understanding of the distribution of both the vertical and the horizontal metal zonation in the orebodies. Because the efficiency of ore processing is affected by ore textures, and because the same mineral commonly has different textures and varies in chemical composition, a relationship between textures of the feed and the middlings must be established for all ore types defined at the deposit scale. Quantitative mineralogical methods have been developed to provide, on a timely basis, the information needed to optimize the concentration processes for the massive sulfide ores at the Aljustrel and Neves-Corvo deposits, Iberian Pyrite Belt, Portugal.

Jan 1, 1997

By Orlando C. Gaspar

The presence of ?ne-grained mineral intergrowths, the complex distribution of deleterious minor elements, and the variable base-metal contents in some assemblages commonly pose technical problems for the processing of volcanogenic massive sul?de ores. The bene?ciation of most massive sul?de ores from the Iberian Pyrite Belt requires extremely ?ne grinding to liberation sizes of K80= 15 µm to 25 µm. For several deposits, mapping of the ore types and metal zoning pat-terns has shown that the different ore types are distributed as ore lenses within the massive sul?des. Mineralogical, textural, and metallogenetic studies have provided an understanding of the distribution of both the vertical and the horizontal metal zonation in the orebodies. Because the ef?ciency of ore processing is affected by ore textures, and because the same mineral commonly has different textures and varies in chemical composition, a relationship between textures of the feed and the middlings must be established for all ore types de?ned at the deposit scale. Quantitative mineralogical methods have been developed to provide, on a timely basis, the information needed to optimize the concentration processes for the massive sul?de ores at the Aljustrel and Neves-Corvo deposits, Iberian Pyrite Belt, Portugal.

Jan 1, 1997

By J. Bouchard, A. Desbiens, M. Maldonado, R. del Villar

ABSTRACT: Despite many years of practical applications in mineral processing plants, the potential of column flotation has still not been fully exploited. The challenge in measuring some key variables is certainly an important contributing factor to this situation. Reliable online measurement of varibles, such as the froth depth, bias, gas hold-up, frother concentration, bubble surface area flux, and bubble size distribution, provides opportunities for the application of various advanced control strategies and real-time optimization based on an economic criterion. For several years, Université Laval’sLaboratoire d’observation et d’optimisation des procédés researchers have been working on these opportunities. This paper describes the most recent advances and current research trends.

Jan 1, 2011

By Stanley G. Butcher

"Introduction Many operators in western Canada, with a background in the minerals industry, talk of ""coal beneficiation"", whereas the coal industry generally uses the term ""coal preparation"" . The sophisticated cleaning circuits and thermal drying units found in western Canada makes the term beneficiation particularly appropriate. This chapter uses standard coal preparation terminology(l,2J and assumes general knowledge of coal preparation unit processes and equipment(3,4,5). The geologic setting and mining methods of western Canada, described elsewhere in this volume, present for preparation run-of-mine coals which have particular problems. As a result the cost of preparation is a higher proportion of the total minesite production costs than in other coal fields . Preparation requirements are determined by the types of coals being produced and the markets in which they are sold. Western Canadian coals have a low sulphur content and do not require cleaning on this account. Prepared coal from western Canada has to be shipped vast distances -to the Pacific Rim countries and Ontario in particular -and the savings in transport costs justify the high costs of preparation. Factors which dictate selection and operation of the preparation processes are: i) Market specifications and coal rank. ii) Size distribution of particles and particularly the liability of coal and refuse particles to degrade during handling and processing. iii) Quantity and characteristics of the associated refuse. iv) Washability characteristics (the distribution of particles by specific gravity within each size fraction). v) Surface characteristics of the fines. vi) Variability of the raw coal. Where the product (coal or discard) has a high fines content special consideration must be given to dewatering, the removal of surface moisture, to give acceptable handle ability characteristics. In the severe winter climate of the western foothills and mountains thermal drying is necessary to prevent freezing of washed coal in stockpiles and railcars."

Jan 1, 1985

By Guy Chevalier

The QCM Mount-Wright mine and concentrator complex produces about 14 M tonnes of iron concentrate annually. Approximately 9.5 M tonnes of this concentrate are used to produce iron ore pellets at four different silica grades: Three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the realization of two projects where the acquisition of new process equipment led to an improved pellet plant iron recovery, a better flexibility and to lower operating costs as well as to the production of fine iron ore concentrate from the Port-Cartier tailings pond. Typical 4.8 % SiO2 concentrate is processed to achieve required pellet silica content. This is obtained with the aid of hindered settlers or hydraulic classifiers, screens, whims and, lately, spirals. The increasing demand for low silica iron ore products resulted in a greater need for upgrading. The Pellet Plant upgrading capacity being limited, more and more iron units were lost. Base on test works results and economic evaluations, QCM engineers figured out a way to increase efficiently their upgrading plant capacity and go back in the pond gather what has been lost in recent years of operation.

May 1, 2007

By J. W. Spyker, D. H. Filson, W. H. W. Husband

"Large deposits of sodium sulphate exist in southern Saskatchewan in the brines or muddy crystal beds of alkali Jakes. Currently, more than 300,000 tons per year of sodium sulphate are produced from these lakes and sold as salt cake to the paper industry. Most of the production is obtained from the brines of a limited number of Jakes.The Saskatchewan Research Council was requested to develop a process for recovering sodium sulphate from the muddy crystal beds so that this type of deposit could be exploited in the future. A flowsheet was developed with the aid of phase diagram data and the process was studied on a pilot-plant scale using raw material from three different lakes. Satisfactory yields and product purities were obtained in all cases, and an economic analysis indicated that a 100,000-ton-per-year sodium sulphate plant could produce salt cake at a cost of $12.26 per ton for a rate of return upon investment of 16 per cent at current market prices."

Jan 1, 1966

By Marcel Vallée

Frequently, costs overruns and defaults in mining project performance result in serious problems and headaches for all project participants and impact on corporate objectives, profits and image and, occasionally, lead to project failure. As mining professional s, we should be very concerned that, in a recent World Bank paper (Weber-Fahr, 2001), geological and technical risks were considered the most important ones facing mining projects. Whenever we manage to reduce or minimize these risks, we are in better position to overcome the environment-, market-, finance- and community-related ones. The causes of this situation seem rather systemic, as a fairly long list of industry problems with new pro jects has been described in industry papers in pas t and recent years. A brief review of industry problems with mining projects will be given first, followed by a review of the basics of the current Quality Management and Continuous Improvement perspectives that have evolved from earlier quality control and quality assurance systems and policies. Particular particular attention will be given to the work of W. E. Deming. As the system approach is an essential part of such policies, it will be described succinctly. Given that poor communications and interactions among geologists, mineral processors and mining engineers/operators ca n seriously affect project efficiency and profitability, these interrelated processes with in the mining systems will be analyzed and modelled and the impacts of such situations will be described through a number of anonymous case histories and examples. A synthesis of Dr Deming's management system, includ ing his Four teen P oints and System of Profound Knowledge, will be prese nted .

May 1, 2002

By Mike Samuels, John Starkey

"This paper examines test results and grinding mill design for the recent Fortune Minerals’ NICO Project, located in the Northwest Territories. SAG milling and rod milling options are compared. Rod milling is clearly shown to be the best option because of the ore’s extreme resistance to breakage in a SAG mill environment.Surprisingly, the Bond Ball Mill Wi was 13 kWh/t for this ore. The Bond Rod Mill Wi was 20 kWh/t, whereas the SAG pinion energy to grind the ore to T80 1.7 mm was 30 kWh/t. The existence of ore with this ratio of SAG hardness to Bond BM Wi has not been previously observed. If not considered, this critical relationship may adversely impact the accuracy of mill design. This paper substantiates the significance of these findings to achieve successful grinding design on ore that is macro-competent during primary size reduction, but relatively normal during secondary grinding.INTRODUCTIONThe NICO Cobalt-Gold-Bismuth-Copper deposit is located 160 km northwest of the City of Yellowknife, Northwest Territories. It is the largest IOCG-type deposit (aka Olympic Dam-type) currently recognized in Canada with Mineral Reserves of 21.8 million tonnes contained within a larger 57 million tonne, lower-grade Mineral Resource. The project, owned 100% by Fortune Minerals Limited, has been assessed in a positive definitive feasibility study, subject to underground test mining and pilot plant testing, and is now in the permitting stage to develop a combined open pit and underground mine and process plant. An updated process flow sheet incorporates conventional crushing, grinding and bulk flotation, followed by filtration for shipment of a concentrate to a purpose-built refinery proposed to be built near Saskatoon, Saskatchewan. At the refinery, separate bismuth and cobalt concentrates will be produced following regrinding. The hydrometallurgical process methods include: pressure acid leach, precipitation, ion exchange, and electro-winning for recovery of cobalt as 99.8% cathode; solvent extraction and electro-winning of by-product copper cathode; ferric chloride leach and electro-winning for recovery of bismuth as 99.5% cathode; and cyanidation of the leach residues for recovery of gold as doré."

Jan 1, 2010