Search Documents

By Ken G. Stowe, Stephen L. Chryssoulis, Joe Y. Kim

"Lead ions originating from galena during processing of complex sulphide ores migrate to ""cover"" the surface of sphalerite and iron sulphide mineral rarticles, and cause poor selectivity in differential flotation. Generally in sulphide ore processing, the lead activated minerals float in the Cu/Pb circuit. Subsequently, surface lead complicates the zinc flotation circuit by lowering the concentrate grade due to the co-flotation of lead- activated iron sulphide minerals. The effect of lead in the differential flotation of sphalerite from Cu-Pb-Zn and Pb-Zn ores is discussed. Plant and laboratory test data are interpreted by determining the surface composition of individual grains of sphalerite and iron sulphide rarticles using two surface analytical techniques, Laser Ionization Mass Spectrometer (LIMS) and Time of Flight-Secondary Ion Mass Spectrometer (TOF-SIMS). Cationic and anionic species on the surface were analyzed to elucidate the phenomena.IntroductionSurface properties play a critical role in many aspects of mineral processing such as flotation, flocculation, etc. An understanding of interaction mechanisms of different reagents (inorganic cations and anions, collectors, regulators, etc.) with mineral surface in an aqueous solution is a very important pre-requisite in achieving the desired selective flotation. In the flotation of complex sulphide ores, the flotation collectors respond to the activation of minerals such as sphalerite, pyrite etc. by heavy metal ions of Cu, Pb or Ag, which is a strictly surface phenomenon."

Jan 1, 1995

By W. R. Hopkins, J. A. Davis

"This paper presents a discussion of the mechanisms by which aerosols of the process electrolyte are entrained into the breathing environment of copper, Zinc and nickel eIectrowinning tankhouses. Literature outlining the health effects associated with worker & posure to the acidic and metallic contaminants found in the airbome aerosols is summarized and compared with existing North American regulations.A brief review of the existing technologies for the source reduction of these aerosols is presented. This paper outlines the industry experience with use of covers, balls, beads, shapes, fixtures and chemical surfaetants. Each of these devices is ranked according to its effusiveness in the process in which it is used, and rated according to its operator acceptance.The various forms of existing in-plant ventilation systems are reviewed with a discussion of their relative merits and effectiveness. Actual experience is related, detailing the methods of testing for ambient contaminant levels in a variety of tankhouse environments. Guidelines are provided for the site and process specific criteria which govern the selection and ultimate effectiveness of a particular form of ventilation system.Finally, actual project experience is cited in which hydraulic modelling is used a design tool in tankhouse ventilation design. These projects include the upgrading of existing traditional ventilation designs, and the ''grass roots"" design of a more efficient aerosol source control system to be used in high altitude, cold weather sites."

Jan 1, 1994

By Kathleen A. Altman

"This paper supplements the information provided annually at the Canadian Mineral Processors Operators Conference regarding the education of Mineral Processors in Canada. The purpose of the paper is to provide information regarding the engineering accreditation process in the United States and the universities that offer programs in Mineral Processing and Extractive Metallurgy in the U.S.There is a critical shortage of trained Mineral Processors and Mining Engineers world wide. The Society for Mining, Metallurgy and Exploration (SME) formed a task force to evaluate the national needs for trained engineers and to track the number of engineers who graduate from U.S. universities each year. The statistical information for Mining Engineers is well-developed. The current effort is to assemble similar information regarding students who graduate with expertise in Extractive Metallurgy and Mineral Processing as well as to explore the limitations of the accreditation system in the United States and its impact on the education of Mineral Processors. The long-term objective is to develop a data base regarding Mineral Processing programs and Mineral Processing graduates that is as complete as the one that has been maintained by the Canadian Mineral Processors.INTRODUCTIONIn the United States engineering curricula are accredited by ABET, which was formerly known as the Accreditation Board for Engineering and Technology. The objective of ABET accreditation is to ensure that educational programs in applied science, computing, engineering and technology meet quality standards set in conjunction with the professional organizations that represent professionals in the industries which hire students graduating from those educational programs. For example, the Society for Mining, Metallurgy and Exploration (SME) is the lead society for accrediting Mining Engineering programs in the U.S. For Materials Science and Metallurgical Engineering programs, the lead society is The Mineral, Metals and Materials Society (TMS). SME is a cooperating society for accrediting Metallurgical Engineering programs. Cooperating societies for the accreditation of Materials Engineering include the National Institute of Ceramic Engineers (NICE), the American Institute of Chemical Engineers (AIChE) and the American Society of Mechanical Engineers (ASME)."

Jan 1, 2008

By M. Sengupta

International trade in minerals plays a very important role in the economic growth of many nations. Several less developed countries a1•e heavily dependent on their mineral exports for earning foreign exchange, which is needed for industrialization. Mineral exporting nations experience many problems in international mineral markets; the most important are tariff barriers, deteriorating terms of trade, instability in metal prices, etc. The formation of international mineral cartels to raise prices can be successful only to a limited extent and only for a short period of time.

Jan 1, 1976

By Jan Butra

Longstanding mining of copper deposits in the Legnica-Glogow Mining Basin, Poland has accumulated broad experience concerning the impact of geological and mining conditions on seismic and rockburst hazard. Methods of rockburst prevention for deep copper mines have been developed based on gathered data. Methods of rockburst hazard evaluation and rockburst control constitute a set of rockburst prevention measures. Due to their nature and location within the production process, prevention methods can be passive or active. Active methods of rockburst prevention consist of the liquidation of stresses in the areas where they are concentrated through controlled generation of rock-mass tremors and rockburst by blasting works (group extraction blasting, release blasting in the rock mass and pillars able to accumulate the stress, as well as in the roof and floor). Group blasting works as a basic method are very effective in copper mine conditions. Provocation of dynamic events makes it possible to control the timing of their occurrence. In Polish copper mines, all blasting works are made during the absence of miners in the mining fields. Daily distribution of both the number of recorded strong seismic events and volume of energy released, confirm the advisability of using this kind of rockburst hazard prevention. The rockburst hazard prevention methods developed over 40 years of copper deposit extraction are economically reasonable and offer sufficient effectiveness under high rockburst hazard conditions.

Aug 1, 2013

By J. C. Gilbert

"IntroductionTHE PURPOSE of this paper is to discuss in a general way the heavy oil situation in Western Canada, and particularly to acquaint those in the oil industry who have not participated in the heavy oil end of the business with past and current developments. The author has covered •briefly the location of the heavy •and asphalt-base oil fields, their geology, current drilling and production practice, the location of the •refineries capable of handling heavy crude, their products and markets, and the problems and future prospects of the industry.Location and Description of FieldsThe term heavy oil is generally used to denote crude of 20.9° gravity and under. Since the products from heavy oil are also to a lesser extent obtained from asphalt-base crudes of higher gravity, some mention will be made here of the latter; but in general the emphasis of the paper is on heavy oil as such.In the order of their production to date, the heavy oil fields and those light oil fields which produce asphalt-base crudes are : Lloydminster, Taber, Vermilion, Conrad, Princess, and Wainwright.The Lloydminster oil field has not only produced most of the heavy oil, but also is currently the largest producer, supplying at the present time about 80 per cent of the heavy and asphalt-base crudes produced in Western Canada."

Jan 1, 1952

By R. Pérez, James A. Finch, F. Tavera, Cesar O. Gomez

"Gas holdup is a variable which affects the operation of flotation columns. On one hand, gas holdup is a function of bubble size (a function of sparger type, frother characteristics and concentration, and air flowrate), tailings flowrate, solids content, and mixing patterns in the collection zone. On the other, gas holdup defines flotation kinetics and carrying capacity. Therefore, gas holdup is a useful variable to control and diagnose the operation of a flotation column, but the lack of a reliable sensor for on-line gas holdup monitoring has prevented its use in industry.This work describes the principle and the practical difficulties associated with the development of a gas holdup sensor based on the measurement of the electrical conductivity of dispersions. Two different approaches have been devised. These approaches will be described and test results presented of prototypes in laboratory and industrial columns.Background.Several years ago, a research program was initiated at McGill to use electrical conductivity as the basis for developing sensors for process measurements in mineral processing. Electrical conductivity is an intensive property which is a function of the concentration of the different phases present in a dispersion. The initial focus was on the detection of the interface between two dispersions with different characteristics (i.e., that between the collection and froth zones in flotation columns or that between clear water and sedimented solids in thickeners). The technique works in this case by searching for the location at which a sudden change in specific conductivity occurs, as a consequence of different gas holdup or solids content, and absolute values of the specific conductivity of the dispersions involved are not necessary1,2."

Jan 1, 1995

By Michel Garon

"Several years ago computer control of the flotation process was successfully implemented at the Matagami concentrator of Noranda Mines Inc. At that time this was the first computer application being installed at this operation. The last few years have seen an extensive use of programmable controllers in areas such as the copper and zinc dewatering circuits and the lime preparation system. With the aid of such instruments, these areas have attained a high level of automation and as a result, a high degree of efficiency. The controllers have proven to be very dependable and easy to use.IntroductionThe Matagarni Division of Noranda Mines Inc. operates two mines in the Matagami District of northwestern Quebec which is located about 650 km northwest of Montreal. The mines ship ores to a central concentrator whose throughput averages 95,000 tonnes of ore per month. Metal contents of the mill feed average 0.9 per cent copper and 5.0 per cent zinc. Concentrate outputs are approximately 3,200 tonnes of copper and 8,200 tonnes of zinc per month.The concentrator commenced operation in 1963. An on-stream X-ray analyzer was installed in 1968, providing analyses of several samples in the flotation circuit without the aid of a computer. In 1974, control of the circuit by computer was added to the system. As a result, zinc flotation efficiency improved considerably and reagent costs decreased through the reduction of copper sulphate consumption.In the past few years it was realized that significant improvements could also be made in other parts of the operation . Copper and zinc dewatering circuits and the lime preparation system were identified as major areas that could drastically benefit from automation. In 1982, programmable controllers were seriously considered as an attractive alternative for achieving the company 's goal. Because of their relative lowcost and their high degree of flexibility, they were selected for implementing automation and, for improving the efficiency in each of these areas."

Jan 1, 1985

By Norman O. Lotter, André R. Laplante

"The pursuit of concentrator surveying for purposes of metal accounting or process optimization has not yet connected with the well-published realm of geostatistics. The reality of lognormality in time has seldom been discussed. One publication by Krige, 1962, examined such effects for a gold concentrator in South Africa, towards an information system that would provide feedback to the mining and surveying teams on grade control of ore mined.During present studies which are designing and testing a new survey model, called statistical benchmark surveying, it was found that the distributions of feed, concentrate and tailings bear significant residual signs of the parent lognormality in space. The multiple hosting of paymetals in different mineral species complicates the understanding of these distributions. These features have to be recognized and treated in order to perform appropriate quality control on the diagnostic sampling performed in the pursuit of statistical benchmark surveying.It is shown in this paper that the above two features can actually be used to advantage in the diagnosis of continuous periods of operations data ahead of such surveying, including the estimation of recoverable paymetals in flotation tailings from a graphical method.INTRODUCTIONAssessment of Concentrator PerformanceMilling and flotation, sometimes accompanied by gravity separation, are well-established unit processes, which have traditionally been used to treat ore that has been mined. This is because these processes liberate, then separate, the valuable minerals, which contain paymetals, from host gangue. This is often done by a combination of crushing and grinding processes, or autogenous grinding, to liberate the paymetal minerals, followed by gravity separation and/or flotation, to separate these valuable minerals into a concentrate, or several concentrates. These concentrate(s) have a lower bulk than the parent ore from which they are derived. Further, they contain a high percentage of the valuable minerals. Accordingly, they are more economically treated in subsequent beneficiation processes than the ore from which they were produced."

Jan 1, 2005

By William H. McCracken, William G. Holroyd

"The People's Republic of China could very well be considered the largest untapped mineral and metal resource in the world. The proven reserves of antimony, barite, bauxite, fluorspar, graphite, lithium, magnesite, mercury, molybdenum, phosphate, pyrite, rare earths, talc, tin, titanium, tungsten, vanadium and zinc are among the largest in the world.Any company involved in the purchase or supply of industrial raw materials has undoubtedly followed the phenomenal growth of some of the Chinese mineral commodities, where growths in production of more than 200010 have occurred during the past ten years, for commodities like barite, cement, gold, gympsum silver and talc. Others, like bauxite and phosphate, experienced production increases in one year alone of over 45%, from 1986 through 1987!A popular rationale in the United States during the past two years has been the acknowledgment by Professor David Calleo, of Johns Hopkins School of Advanced Studies, that ""America is not sinking-the rest of the world is rising"". While we recognized this rise to be that of economic power for Japan, Korea, Brazil, Taiwan and, more recently, the newly-combined Germanies, China has also successfully completed her own modern five year development binge. But with each boom there is also a bust, and the start of the 1990sfor China shows signs of economic distress. China posted a budget deficit equivalent of US$1.9 billion in 1989 coupled with official inflation at 18010. Projections for 1990 are for US$1.8 billion deficit and inflation as high as 24%. However, government spending in the first seven months of the year climbed 16.4%, outpacing an 11.6% rise in revenue. Spending increases have been related to the government policy to keep prices on domestic goods artificially low, through subsidies, and to bailout inefficient state companies."

Jan 1, 1991

By Ron Jessulat

"IntroductionBrunswick Mining and Smelting Corp. Ltd. is a IO 500 tid base metal producer. Development is carried out by Jarvis Clark MJM-21 3-boom development jumbos, using Tamrock E400, 410 and 550 pneumatic drills. Typical drift size is 13 ft by 18 ft with a 12-ft advance per round. Blast holes are 1 ½ in. in diameter while reamed holes are 3 in. in diameter. AN/FO is the principal blasting agent, being loaded by C-I-L model60R intermediate loader. The detonators are NONELS and DETINELS. Sulphide dust explosions occur during blasting when dusts from certain minerals such as pyrite and pyrrhotite are ignited by name from the detonating shots. The result is a secondary unwanted explosion with a characteristic shock wave and name front that are very destructive to mine services such as ventilation ducting, electrical cable, and ventilation control doors.A typical reaction in the Brunswick orebody occurs according to the chemical formula:4FeS 2 + IIOs-2Fe2O3 + 8SO2 + 3458--(Enright , 1988)The hematite (FeO3) is deposited as a red dust in the blast area while the toxic sulphur dioxide gas (S00 contaminates the underground workings . The presence of S02 gas disrupts production until it is purged from the area by the mine ventilation system or dissipates slowly in those areas where the vent ducting has been melted by the name front or torn down by the shock wave.Sulphide dust explosions exact a high economic toll. Direct costs in damaged materials and wages are probably exceeded by the value of lost production and disruption to the mining cycle. In addition, the health and safety concerns associated with sulphide dust explosions cannot be ignored."

Jan 1, 1993

By C. -G. Berg, J. T. Tuominen

Since the beginning of the 20th century, energy efficiency in copper smelting has been improved by a factor of 30 as a result of adopting autogenous smelting processes with more and more efficient waste heat recovery systems, increasing use of oxygen enrichment and countless smaller improvements. Nevertheless, energy in the form of electricity and fuels continues to be the biggest contributor to smelter operating cost. Metallurgists around the world are under constant pressure to find ways to save those precious megajoules wherever they can. One area that is often neglected is the removal of water contained in concentrates. Copper flotation concentrates, as delivered to a smelter, typically contain some 8–12% moisture. This moisture must be removed and the only way to do this is by evaporation, which consumes a lot of energy. Several studies have shown that the most efficient way of removing this moisture is to use a steam- heated indirect dryer—the least efficient way being the feeding of wet concentrate directly into a smelting furnace. Even in the most efficient smelters that employ modern steam drying, the energy needed to remove the moisture from the concentrates constitutes over 15% of the total energy consumption of a smelter – acid plant complex. The major steps that have been taken in the past to lower the energy consumption of moisture removal are the use of drying in general and the adoption of steam drying. The energy efficiency of concentrate drying has been improved by 25% over the last 20 years. The latest giant leap in this area, the Kumera Heat Recovery Dryer, is the result of Kumera’s long-term development in improving the efficiency of concentrate drying. The Heat Recovery Dryer is a novel application of steam drying that uses the waste heat from dryer exhaust gas for drying concentrates, thus, cutting the energy consumption by a further 30%. This paper discusses energy consumption in copper smelting in general and analyzes the energy consumption of concentrate drying in detail. Different dryer types are compared especially from the perspectives of energy consumption and environmental emissions. Applicability of different energy sources for drying is evaluated and discussed. The principle of the Kumera Heat Recovery Dryer is presented along with results from extensive continuous pilot plant tests. Potential applications and the feasibility of Kumera Heat Recovery Drying technology are discussed.

Jan 1, 2019

By Corrie Pitzer

Safety performance in many companies and even industries has stalled in the few years. Accidents rates are at a ?plateau? and yet, serious accidents and fatality rates are not. In more dramatic cases, such as in the BP Texas disaster, organizations that have ?exemplary? safety statistics, suddenly have a catastrophic or multi-fatality event occurring. Other classic examples are the Piper Alpha disaster and NASA?s Challenger and Columbia disasters and even the Chernobyl nuclear reactor. Looking into the root causes of these accidents provides an insight into the events and deficiencies that led up to the accident, but what are the common features in the organization?s mindset? What characterizes these organizations? decision making, their approach to safety and to risk and are there specific cultural features that can be delineated? The research and review presented in this paper covers a period since 1994, which started in the Australian resource industry and since then covered international events. The features of these organizations are summarized as the seven deadly delusions, based on extensive research since 1997 of organizations that suffered unexpected disasters. Their huge focus on safety, the achievement of lofty goals and celebration of safety successes led to ?mindset? that they are leaders in safety, protected by an extraordinary safety system and that their safety incident figures indicated a truly world-class safety performance. It led them into the trap of the seven deadly delusions?

May 1, 2011

By Kurt D. Mitchell

"This paper discusses general application for A C variable frequency drives in the mining industry. A review of induction motors characteristics, adjustable frequency controller fundamentals, and three commonly used controllers is presented. General application guidelines for the three different types of controllers; variable voltage input , current source input and pulse width modulated are then reviewed in detail, and an example of the economic benefit of this technology is discussed. IntroductionSoon after static DC variable speed drives were well established in industry, a need for static AC variable speed drives was seen. The first technical papers describing possible systems appeared in the mid-1960s, with commercially available units arriving in the early 1970s. Without exception, static AC drives are substantially more complex than their DC counterparts, but they have some very desirable properties. As compared to DC motors, AC motors are less costly, physically smaller, more reliable, require less maintenance , easily sealed, have good load regulation, are able to run at higher operating voltages, and have little danger of over-speed runaway . These properties are particularly desirable in explosion-proof, submersible or difficult accessibility applications.Variable speed AC drives are now a proven technology. available in packages from Sub-horsepower to hundreds of horsepower, from 115VAC to 4160 VAC. This paper covers the principles of operation of three common types of controllers, application criteria, motor consideration and finally an example of how an AC variable speed drive can pay for itself in terms of energy savings."

Jan 1, 1986

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988

By J. A. Finch, G. Labonté

"A long-standing objective has been to obtain interpretable measurements of the oxidation-reduction potential in mineral slurries. For this purpose several sensing electrodes (black platinum wire, platinum foil and spiral, gold foil and spiral, and sulphide minerals such as chalcopyrite and galena) were investigated to determine their response to the presence of sulphide minerals in the pulp, and to the addition of reagents commonly used in flotation. The observed discrepancies between the electrodes may be explained using a combination of the classical mixed potential model for complex solutions and the probability of contact between the mineral particles and the sensing electrode. It is shown from laboratory testwork that gold spirals are preferred over platinum electrodes. Finally, some of the practical aspects of using the electrochemical measurements in a plant environment are discussed.IntroductonThe interpretation of flotation of sulphide minerals in terms of electrochemical (electron transfer) processes has brought new possibilities for process control of selective flotation. Investigations on massive and compacted particulate bed electrodes have shown that the flotation of a given mineral in the presence of a collector can be controlled by the potential induced on the mineral surface. Also, phenomena such as collector less (self-induced) flotation, activation by heavy metal ions, and natural selectivity sustained by galvanic coupling during flotation might also be controlled by electrochemical means.The technique for measuring electrochemical potential in slurries is an adaptation of that used for solutions. The measurement of the oxidation-reduction potential of a solution (ORP , Redox, Eh) is usually carried out by immersing a noble metal electrode (platinum, gold or silver) and a non-polarizable reference electrode: Standard Hydrogen Electrode (SHE), Standard Calomel Electrode (SCE), or silver/silver chloride (Ag/AgCl) in the solution. (The abbreviation Eh implies the SHE is the reference electrode.) The potential difference between the two electrodes is measured using a high impedance electrometer. ASTM standard D 1498-76 (revised 1981)(1) covers the practical details of such measurements; however, it does not deal with their meaning either in complex solutions or in mineral slurries ."

Jan 1, 1988

By Y. H. Hatzor

"This is an extended abstract for a keynote lecture delivered by the author during the 2015 ISRM congress in Montreal on the application of the numerical discontinuous deformation analysis (DDA) method in rock mechanics practice. Due to the large scope of the topic this lecture will focus on studies performed by the rock mechanics group at Ben-Gurion University, alone or in collaboration which other research groups, and is not intended to provide a comprehensive review of everything that has been done on the subject worldwide during the past two decades. A forthcoming textbook (Hatzor et al., in preparation) will attempt to provide such comprehensive coverage.DDA has been developed by Dr. Gen-hua Shi while he was doing his PhD studies under the supervision of Professor R. E. Goodman at U. C. Berkeley (Shi, 1988). Dr. Shi has invented a new numerical discrete element method which provides a solution for dynamic deformation of block systems, hence its applicability to rock mechanics practice. The method is similar in essence to the finite element method in its implicit formulation of the time integration scheme and where in every time step the minimum potential energy of the entire system is sought, but here every element is a finite block with six degrees of freedom. The blocks are assumed to be stiff (simply deformable) so that most of the energy is consumed by slip along pre-existing discontinuities, the frictional resistance of which is assumed to obey the Coulomb-Mohr failure criterion for rock joints. The greatest advantage of DDA over alternative numerical discrete element methods is its robust area (volume) integration which ensures great accuracy even when the blocks are of irregular shapes, including non-convex blocks which may contain holes. The greatest disadvantage is the necessity to solve in every time step very large matrices of unknowns, imposing great CPU demand when the block system involves a large number of blocks. Another disadvantage is the sensitivity of the solution to the choice of the penalty parameter which is implemented in DDA in the form of stiff springs that are attached to contacts once detected automatically.The inherently dynamic formulation of the DDA method lends itself to solution of dynamic problems in rock mechanics. Dynamic analysis with DDA can be performed in different ways corresponding to different rock mechanics problems and loading conditions. Three main classes of loading conditions which are relevant to rock mechanics applications are discussed here: 1) dynamic loading of a single bock which rests on a stationary foundation, 2) response of a block to dynamic loading of the foundations, 3) wave propagation through a block system.The most common approach is to introduce the dynamic force to a specific block in an otherwise fixed block system and check the resulting deformation, typically the time dependent displacement or rotation of the loaded block. This approach is particularly useful for dynamic rock slope stability studies when a stability of a specific rock block against earthquake vibrations is in question. The first 2D-DDA benchmark test of this approach was performed by Hatzor and Feintuch (2001) who introduced harmonic acceleration functions into a block which rests on an inclined plane. The analytical solution proposed for this problem by Hatzor and Feintuch (2001) was later generalized by Kamai and Hatzor (2008). The first 3D-DDA benchmarking for this approach was presented by Bakun-Mazor et al. (2012) who studied single and double face sliding of blocks which rest on stationary foundations and subjected to harmonic input acceleration functions."

Jan 1, 2015

By M. Meratian

The in-situ methods have been developed in production of aluminum matrix composites. A commonly adopted in-situ method involves reaction between a metal oxide and aluminum to produce alumina particles or whisker reinforcements. Aluminum-alumina particle composite was fabricated by in-situ method where alumina particles were produced from reduction of copper and silicon oxides by melting and casting aluminum. Aluminum matrix composites reinforced by Copper and Silicon alloying elements and alumina particles have been obtained. The size and shape of alumina particles were studied by scanning electron microscopy (SEM). The size of alumina obtained from mixture of SiO2 and CuO was bigger than the alumina particles obtained from CuO.

Jan 1, 2007

By Janet S. Springer

Anomalous gold concentrations in carbonaceous material have given rise to misconceptions about the role of carbon in gold depo its. Some hydrocarbon and carbon-rich black muds may how gold contents raised to 100 time above background by mechanical entrapment. urface effect in fine ediments. and metabolic fixing of gold by micro-organisms. Such concentrates, however, are 10 times too low to be economic. Studie in the Archean of Ontario show that graphite schi t are not the protore to an economically workable gold deposit. A later event of gold introduction ha been uperimposed on the initial low concentrations. Gold enrichment i localized by reduction at vein margins where hear plane . the conduits of mineralization, cut carbonaceou horizons.

Jan 1, 1986

By C. P. Verschuren, P. W. Kingston, W. F. Caley

"In recent years, there has been rapid growth in the use of natural stone building and construct ion products. The largest growing markets are for pre-fabricated natural stone panels for interior and exterior wall facing and flooring. This increased demand is attributed to advanced quarrying and processing technologies, renewed appreciation for the aesthetic appeal of natural stone, and to the superior durability of natural stone when compared to glass, steel, and concrete. Geologically, plutonic rocks, and to a lesser extent marble and limestone/dolostone, are used extensively for these applications. This paper details the economic structure of the dimension stone industry, describes the necessary characteristics of a stone quarry, and outlines the geological criteria which favour an economic quarry.INTRODUCTIONThe world building stone industry has remained relatively stable over the last 5 to 6 years. In contrast, the North American stone industry has experienced substantial growth during that period. The increased use of commercial granite is primarily responsible for this growth, where use as exterior wall veneer for commercial, industrial, and institutional buildings represents the largest and fastest growing market.This increased usage in the construction industry has been sparked by the application of new technologies in quarrying, processing and installation , ma king natural stone more competitive with man-made materials which are energy intensive to produce, and have risen dramatically in price. The development of safer, time-saving stone installation techniques has also appealed to the liability-conscience construction industry. Finally, there is a trend by designers and architects toward utilizing long-la sting weather-resistant building materials, and a renewed appreciation of the aesthetic appeal of natural stone. The other large user of granite is the monument industry of North America which, although it has decreased slightly in recent years, still consumes approximately 40% of all commercial granite produced. The local use of commercial marble has remained relatively stable, and North America still relies heavily on European sources and suppliers. There has been some concern over the use of marble for exterior applications in areas subject to acid rain, and in colder climates where the marble ma y be vulnerable to freeze thaw cycles. Despite these concerns, the greatest problem is not with the structural breakdown of marble but the inability of some marbles to retain their polished finishes in the se environments. As a result, there has been an increase in the use of granite at the expense of marble for exterior applications. Finally, commercial marble is used extensively for interior flooring, wall s, counter tops, furniture, sculptures, and stairway components"

Jan 1, 1989