Search Documents

The construction, commissioning and operation of a continuous pilot-scale selective agglomeration (oil agglomeration) unit are described. This plant has been used to recover fine coal from an effluent stream that is produced by a jig plant which scalps the coal from a New South Wales (Australia) colliery. The reject slurry is extremely fine (66.5% minus 53 um) and has an ash content of approximately 40%. The pilot plant can treat up to 0.3 tonne/h of this slurry, producing average product ashes as low as 9.1% and tailings ashes greater than 80%. The average yield observed was62%, which corresponded to a recovery of coal material of 88%. The operation of this pilot plant yielded data that enabled an economic assessment of this type of processing to be carried out. This study showed that selective agglomeration is an economically viable process for eliminating the substantial losses of coal to tailings ponds and minimizing consequent disposal and environmental problems. A commercial plant has been constructed and commissioned on the basis of the data obtained from this pilot-scale operation.

Jan 1, 1979

By A. Darragh

"Past Growth The Canadian coal industry has grown rapidly during the past two decades. Coal production increased over four-fold between 1965 and 1982; consumption almost doubled, imports remained relatively flat, exports soared and total demand increased nearly two and a half times. Coal production grew during this period at an average rate of 8.60/o, compounded annually; this remarkable performance is shown in Table 1 and Figure 1. The relationship between production and consumption is shown in Figure 1, where in 1981 the total Canadian production of coal for the first time exceeded total Canadian consumption. ln Figure 2, the relationship between imports from the United States and Canadian coal exports is shown; in_ 1981 again for the first time, exports offshore exceeded imports into Canada. The rapid growth in Canadian coal use between 1965 and 1982 followed a major decline after World War II, as the country moved rapidly to an oil based economy. Changes in consumption patterns between 1945 and 1982 are shown ~n Table 2. Railway consumption of coal was reduced to zero m the early 1960s. The industrial and domestic consumers market share fell from about 660/o in 1960 to 6.70/o in 1975; this share, however, appears to have stabilized in recent years and actual volumes can be expected to increase in the future. The steel industry's share of the coal market fell over the same period, but the volume in recent years has remained fairly constant at about seven megatonnes per year.Perhaps the most significant change in consumption is in the share of coal consumed in the generation of electricity; this has increased from 80/o in 1960 to over three quarters of the total Canadian coal consumed in 1982. This increase in thermal coal consumption has been supplied by indigenous coal, and was accompanied by a decreasing share for coal imported from the U.S.A. into central Canada. It is expected, because of the nuclear power commitment in Ontario, that this share will continue to decrease, although the total volume of coal imported may increase slowly over time. This will likely also have a dampening effect on future coal sales to Ontario from western Canada."

Jan 1, 1985

By R. N. Chakravorty

Environmental monitoring plays a key role in coal mine safety. In recent years, significant advances have been made in the development of systems suitable for monitoring air in underground coal mines. Because of intensive mining and large capital outlay, the need for higher productivity consistent with safety is well recognized and it appears that environmental monitoring may help achieve this objective. This paper reviews the state-of- the-art in the monitoring technology with particular reference to hazardous gas detection in underground coal mines. The preliminary results obtained from ongoing studies, with regard to continuous monitoring of methane and carbon monoxide in mine air in some of the operations in Western Canada, are discussed. The inadequacies of the methods using spot samples are examined and the need to supplement the present practice with continuous monitoring systems is emphasized.

Jan 1, 1979

By Hans von Michaelis

"INTRODUCTIONThe renaissance in gold and silver recovery technology has continued to unfold and it is appropriate to review some of the useful new technologies as well as try to identify some of the industry's future needs and frontiers.The remarkable strengthening in the US dollar has resulted in a relatively low gold price in US Dollars of around $310/oz at the time of writing and silver at $6.25/oz. This general softening in the dollar prices and the recent confusion as to environmental compatibility of cyanidation tailings and effluents, has led to a slowdown in announcements of new operations. Another reason for the slackening off in the USA is that in the past few years a large part of the capital has come from oi I and gas companies that now seem to be losing interest in mineral ventures, and foreign investors for whom the dollar is becoming out of reach. In the author's opinion this represents an unprecedented window of opportunity.Elsewhere in the world where local currencies have weakened, the price of gold is at or close to its all time high.For example, in South African Rands, the gold price was R571.00/oz when the rand was US$1.47 and the gold price reached US$800. Now at US $309/oz and with the Rand at US$0.51 = Rl .00, the local gold price is R600. The price of si Iver in Mexican pesos is not much less than it was when silver reached US$50/oz. Gold, and silver prices in local currencies outside North America are still buovant and at levels where additional investment in new projects is more encouraging.Even in Canada where the dollar is worth about US$0. 75, this provides a smaller but significant cushion compared with US operations. Considering the present strength of the US dollar and even the Canadian dollar relative to many other gold producing countries, there should be significant investment opportunities at today's prices. Mining companies have started to descend on Brazil, for example, where in a matter of just a few years annual gold production has increased from 10 to 70 tons. In South Africa, a Canadian company backed by Swiss financing has been able to take over a Witwatersrand gold mining operation and is installing a huge new tailin9s retreatment plant to process about 1 million tons per month of tailings."

Jan 1, 1985

By V. I. Lakshmanan, I. G. McColl

"Heap leaching of gold ores in permafrost conditions is feasible provided certain criteria are met. These criteria include relatively short heap leach residence time and the availability of waste heat.This paper describes the conceptual design of such a system for a mining operation in the North West Territories of Canada. The design includes the concept of continuous countercurrent leaching in enclosed ore heaps.Indicative capital and operating costs are given.INTRODUCTIONIn April 1984, Acres Davy McKee Engineering Inc. (ADM Eng.) in association with Ontario Research Foundation (ORF), was invited to carry out a preliminary design, cost estimate and financial analysis to assess the viability of gold heap leaching in a permafrost region in North West Territories, Canada.An orebody was being explored which could, by nature of its mineralogy, be upgraded substantially by crushing and screening in the size range of 1/4 in. to 3/4 in. It was proposed to process the screen undersize through an existing gold mill on site and to treat the oversize material in a heap leach facility to be constructed adjacent to the existing mill.Despite the formidable challenges imposed by isolation, permafrost and harsh winter conditions, the heap leach project was considered worthy of examination because of the relatively high grade of the heap leach material (> 0.1 oz/ton), very short leach times (in the range of 1 to 4 days) and the availability of substantial quantities of waste heat from the diesel generating station on site.Design challenges included the necessity to maintain the permafrost in frozen condition, to prevent freezing of ore and leach solution, to limit size of construction materials to that which could be carried in a Hercules freight plane and to contain water usage at an absolute minimum level."

Jan 1, 1987

Presentation Overview ?WRDC Purpose and Activities ?Women in Trades, Technology and Operations (TTO) Occupations ?Factors in Successful Recruitment / Retention of women (VBNC) ?Recruitment and Retention Strategies ?Conclusion Women in Resource Development Committee (WRDC) ?Incorporated in 1999 as a Not for Profit Organization ?Based in Newfoundland and Labrador ?Works to Increase the Participation of Women in Natural Resource Industries ?Research (Using Gender-Based Analysis) ?Career Exploration Programs for Women and Girls ?Outreach and Advocacy ?Policy Development ?Public Awareness and Education ?Gender Sensitivity Training ?WRDC Educational Resource Centre

May 1, 2006

By W. Evans, C. E. Ells

Nuclear power reactors using zirconium alloy pressure tubes generate electricity in several countries. Such reactors are particularly important in Ontario, where CANDUs* generate about 30% of the total electricity produced in the Province. Starting with the commitment of NPD-2 in 1956, the pressure tubes of the first five CANDU reactors were made of coldworked Zircaloy-Z, an alloy of Zr and Sn. This alloy was developed by the US Navy, but the decision to use it in a cold-worked condition was based on AECL work. In 1958, the USSR published information on a new alloy, Zr-2.5 wt% Nb. The Nb promotes stabilization of the (3-phase in the material, thus presenting opportunities of exploiting metallurgically strong pressure tubes analogous to the heat-treatable cx-{3 titanium alloys. After construction of two reactors using Zr-2.5 wt% Nb in a quenched and aged condition, an extensive development program on cold-worked Zr-2.5 wt% Nb pressure tubes resulted in them becoming the reference tubes for all CANDU reactors committed since 1966. Anticipating the future needs of the domestic and export markets, AECL have pressure tubes of Zr-3.3 wt% Sn-0.8 wt% Nb-0.8 wt% Mo (Excel) in an advanced state of development. These tubes will be used in an annealed condition; our projections show that they will have improved dimensional stability over the lifetime of the reactors. These improvements result from experimental programs leading to an understanding of the relationship between microstructures and fabrication variables and effects of the environment during service in nuclear reactors.

Jan 1, 1981

By A. J. Faulds, K. C. Westaway, Z. Waszczylo

"PAH compounds have been found in the exhaust from all types of engines burning hydrocarbon fuels . They have also been found in the air over cities and in water. The authors report on a study to assess the concentrations of twelve different PAH compounds in several different environments in dieselized underground mines. In addition, the differences in the PAH levels and distributions in different mines will be demonstrated. Finally, the influence of blasting and the type of diesel engine used as well as the effect of catalytic converters in the exhaust system on the PAH concentration in the mine will be discussed.IntroductionMining methods have been altered significantly in the last 25 years; i.e ., the tools and machinery used underground have changed from electrically operated trains and other equipment to diesel-powered equipment. This has been done for several reasons: 1) economics, 2) convenience and 3) safety. Today, most mines are heavily committed to using diesel equipment.Although the introduction of diesel equipment has revolutionized mining methods and has been a tremendous boon to the mining industry, it has also created new problems. These problems arise because the exhaust from diesel engines contains several pollutants which can be hazardous to the health of the miners. These pollutants are CO2, CO, NO., SO2, oxygenated hydrocarbons produced during the buring process and unburned hydrocarbons. There are two classes of hydrocarbons, of which polynuclear aromatic hydrocarbons (PAHs or PNAs) are a part."

Jan 1, 1981

By C. Bergstrand

"Precipitation of gypsum and the formation of scale may pose a serious challenge in the leaching of several minerals. As an example, precipitated gypsum may form scale in the machines increasing the need for maintenance. Alternatively, it may encapsulate precious elements, i.e. gold and lower the recovery during subsequent leach processes. In this work we explore how different biopolymers modify the rheology of gypsum at three different pH levels at ambient and elevated temperatures. The ability to disperse gypsum vary with temperature, pH and biopolymer. It is also inversely related to the scaling potential. Measurements of the zeta potential as a function of increasing amounts of biopolymer reveals that the magnitude of the zeta potential changes in the presence of biopolymer, and so does the ability to disperse the gypsum suspension. Similar results with hematite will also be discussed. The methodology and results may aid in the selection of additives used in mineral processing applications where scale pose a problem.INTRODUCTION Processing of refractory gold ores normally involve either atmospheric or oxidation under pressure in order to convert sulfides to oxides (Weir, King, & Robinson, 1986; Weir, Robinson, & King, 1986). This conversion facilitates leaching of gold (and silver) in normal CIL processes. During oxidation, sulfides are converted to sulfates. Normally, there is an abundance of calcium ions in the process water, either released from the ore or added as lime to adjust pH for the CIL process. Precipitation of calcium sulfate, or other compounds (calcium carbonate, jarosite, hematite) is a way to remove gangue minerals from the solution entering the CIL circuit (Ji, King, Fleming, & Ferron, 2010). Precipitation may also cause challenges in the process as gold (or other valuable elements) may become encapsulated in gangue. (Beauchamp, Choung, & Xu, 2006). In addition to precipitation, the precipitated gangue minerals may solidify and form scale in the processing equipment. Recently, Lauten and Kluck (2016) found that dispersants used as scale inhibitors to prevent encapsulation of gypsum did not modify the solubility of gypsum. In the utilised model system, similar amounts of gypsum precipitated with and without dispersants. Instead, it was found that the dispersants evaluated as scale inhibitors reduced the yield stress of gypsum suspensions. The reduced yield stress was associated with a reduced tendency for gypsum particles to agglomerate and form scale."

Jan 1, 2017

By Alfred W. G. Wilson

THE state of development of its iron and steel industries serves as a 1eading index to the general condition of a nation's business affairs. In this paper, the authors present an economic study of the progress of this group of industries in Canada for the decade 1927-1936. The statistical data and most of the tables which accompany this article have been com-piled by John Casey, Statistician, Bureau of Mines; the text and some of the computations have been prepared by the seni0r author. The principal source of statistical information has been the publications of the Dominion Bureau of Statistics; where other sources have been consulted, they are noted in the text. All weights are given in short tons. Records for the years 1913 and 1918 are also presented in the group of tables dealing with iron ore and pig iron; they will serve as a basis for comparison with nearly normal years in the two decades prior to 1927-36, which included the abnorma1 years of the Great War. GENERAL REVIEW At the beginning of the decade under review, this group of industries had returned to almost normal production, as determined by pre-war conditions. Iron ore consumption showed a steady increase between 1927 and 1930; a marked decline began in 1930 and reached its culmination in 1932, when the recorded consumption of ore was 293,353 to11s, about 16 per cent of the average consumption during the first four years of the decade; the last four years of the decade show a gradual increase in consumption; the amount of ore used in 1936 was still slightly below the amount used ten years before, in 1927 (see Table 1, top).

Jan 1, 1938

By W. S. (Steve) Vaughan

The Origins of Joint Ventures in Canada?s Mining Industry ? Among the most important financing structures used in our mineral industry today ? Virtually unheard of in the Canadian industry prior to the 1970s ? Borrowed from the U.S. oil and gas sector where it came into prominence in the late 1930s ? The Securities Acts of 1933 and 1934 in effect killed the sale of (equity) shares for financing oil and gas wells and start up mining companies

May 1, 2013

By Michael Farley, Paul Dufour

"Relationships, Partnerships,Marriages (RPM)RPM has a nice musical ring to it, but it is in fact synonymous with science and technology, university-government -corporate links and the more genera l issue of university roles in technology development. Pick up any report on one of these issues, and chances are that you will find one of these key words in the title. Play it, and you will find that the revolutions per minute are increasing. It is difficult to keep track of the wide variety of institutional experiments now developing in Canadian universities in attempts to marry science and research with technology commercialization and technology transfer.Why is the role of Canadian universities in this matter important? There are at least five good reasons:1. It is important because these knowledge institutions are producer s of scientific research, a major component of technology. Today the gap between the two is rapidly shrinking.2. It ' is important because Canadian industry is turning to universities for tech no logy development and new knowledge. Figure 1 shows that universities are becoming an important source of technology available to Canadian firm s; more important in fact than government. Figure 2 illustrates this trend more graphically in showing that university collaboration is one of the preferred methods of industry participating in co-operative R&D efforts:3. The role of Canadian universities in technology development is also important because the provincial and federal governments have embarked on various programs and policies for promoting the use of technology and science for economic benefit. Universities are playing an increasing role here. For example, the submission of IDEA Corporation (a venture capital operation funded by the government) in Ontario to the Bovey Commission on the Future Development of Ontario Universities clearly spelled out its ideas for commercialization of university research in Ontario . Among other things, the brief suggested that Ontario's universities need to be better equipped to transfer technology, and the reward structure in university research must incorporate industrial interests."

Jan 1, 1986

By L. Nutter, J. Clancy

"Barite is used extensively by the oil and gas well-drilling industry as a weighting agent. It is particularly well suited for drilling mud because of its qualities; it is non-abrasive, heavy, virtually inert chemically, easy to handle and inexpensive compared to other available heavy materials. Increased deep well drilling in Western Canada, and especially in the Arctic regions, could dramatically affect the demand for barite through this decade. Known deposits in northeast British Columbia are possible sources of incremental barite supplies, should the situation develop.IntroductionThe purpose of this report is to examine the opportunities for expanding barite production in British Columbia. Of primary interest will be the relationship between the projected future levels of production and consumption of barite in Western Canada and the extent to which increased domestic production could replace the need for imports in filling any expected supply shortages.After a brief overview of the nature and uses of barite and some of the relevant features of the barite supply industry, the discussion will turn to the supply gap in the Canadian market and the possibilities for import substitution.OverviewBarite is an industrial mineral which is used in large quantities by the oil and gas well-drilling industry. It is often an important component of drilling mud, a fluid circulated continuously in the well during the drilling process to lubricate and cool the drilling apparatus and to contain the high oil and gas pressures found at depth. Barite (BaSO4) is particularly well suited as a weighting agent for drilling mud because it is a heavy (specific gravity to 4.5) inert mineral which is inexpensive in relation to other materials having a high specific gravity. In the on-site use of drilling mud, ground barite is combined with numerous other solid ingredients and chemicals in the form of a slurry. Other advantages of barite include cleanliness, ease in handling and its non-abrasive character (hardness of 3-3.5)."

Jan 1, 1982

By M. Stelter

Since the first years in copper electrorefining natural products have been used as so called "additives" in the electrolyte. Glue as one of these additives offers a lot of different reactions with the metal ions and also with other additives like thiourea in the electrolyte. For a deep understanding of the effect of these additives it is important to know the routes of possible reactions in the electrolyte as well as the basics of electrocrystallization. Using this knowledge the interpretation of nodulation or inclusions of electrolyte in the cathodes in copper electrorefining is easier than before. Setting up on physical and chemical properties of the electrolyte and the additives practical investigations of the effects of additives in copper electrorefining and their impacts on copper crystallization and cathode quality are presented in this paper. Chemical deposition of glue against time and temperature are only few of the effects that are mainly caused by the use of natural products. In fact parameters like anodic and cathodic polarization are strongly affected by the additives as well as the effects of the additives are strongly affected by current density. This second part of the paper presents results concerning interactions of the above mentioned parameters.

Jan 1, 2007

By Roger Lafrance

"This paper discusses various aspects affected by the use of large-diameter boreholes in underground mines. Topics covered consist of noxious fumes, vibrations, post-blast effects, various types of explosives, the cordine system in production blasts, the slider primer system and wall-control methods. In general, the paper is an overview of this important fact of underground mining.IntroductionWith economical factors leading the way, many reasons motivated drilling equipment companies to develop equipment that can drill holes up to eight inches in diameter and even larger for underground applications. One of these other reasons is the fact that many orebodies were considered marginal, given the high costs of conventional mining methods utilizing small diameter boreholes. With these criteria in mind, accelerated programs were put in motion to develop equipment that would reduce both-development and production costs in underground mines. Change s in any basic program often affect other areas down the line. This is particularly true with the ad vent of large-diameter boreholes underground.C-I-L Inc. is certainly no stranger to this phenomena. Whether production headings increase in size and tonnage or whether production increases due to lower costs, one fact remains unchanged and that is the fact that all development and production holes are loaded and blasted whether they be of small or large diameter. Due to this fact, C-I-L Inc., as a leading explosives manufacturer, initiated a program to examine blasting methods in use in surface work with the intent of revising these method s for underground applications. Research facilities were also oriented toward developing appropriate products. This was a task that was accepted with anticipation, with the result that many new blasting systems and methods were brought forward, thanks to the collective efforts of both the consumers and manufacturers."

Jan 1, 1984

By K. T. Audt

The Yayoi period, from about 300 B.C. to A.O. 300, represents a time of important changes in Japanese history. During this period the advanced rice culture of the Asian continent was introduced to Japan, along with the techniques of animal husbandry, spinning, bronze casting and metal working(1) . As was the case in the Jomon period (11000 B.C. to 300 B.C.), the Yayoi period is traditionally defined by a particular type of pottery, characterized by the use of the potter's wheel and an extreme simplicity of decoration and form(2) . Pieces of this pottery were found in 1884 in a district of Tokyo, known as Yayoi-Cho, not far from Tokyo University. Within a decade the name Yayoi had come to be used for the period which also saw the first casting of metals in Japan121. During the Yayoi period, the foundation of the ancient Japanese state was laid as the individual small communities were unified and as labour specialization and social levels developed. In fact, the Yayoi may be the true ancestral culture of Japan(3) . However, the origin of the Yayoi is not definitely known. One theory indicates that the Yayoi people may have been driven from the Asian mainland (via Korea) by the dynastic wars that accompanied the unification of China under the Ch'in and Han and that these settlers rapidly displaced the Jomon. Bronze objects and the cultivation of rice may have arrived about the same time - in the third century B.C. Iron was in Japan within another century, but since it rusts badly and disintegrates, only a few small pieces are known from such an early date(4) . After about 50 B.C., the Yayoi cultures of western Japan were in fairly close and regular contact with the continent via Korea(5)

Jan 1, 1999

"IntroductionNOTE.-All figures on the supply and consumption of coal in Canada cited in this paper were collected and reported by the Dominion Bureau of Statistics. The friendly and efficient co-operation of the officials of the Bureau. is the foundation upon which it has been my privilege to rely in the preparation of this and two earlier papers ( 1). My thanks are due also to our own staff on the Dominion Coal Board, who spared neither time nor effort in helping to prepare this paper.STATISTICS are comparatively dull and, to many people, coal statistics are duller than most. Coal is, however, the one basic mineral upon which our whole way of life depends and it may be well if attention is drawn to this fact by an occasional statistical review of the coal position in Canada. The recent furore over the oil and gas discoveries has so obscured the basic position of coal in many minds that a little basic coal information may be useful. It is for this reason that, for the third successive year, a factual survey of the coal position is being presented.In the previous papers (1) explanations have been given of the basic considerations in the preparation of these reports and some special phases of the overall picture have been examined. For these explanations, the earlier papers may be consulted."

Jan 1, 1952

By Bruce C. Smart

"Very little attention was given to the regulation of uranium mills by the Atomic Energy Control Board prior to 1974. The ore grade treated by Canadian mills in the past was in the order of 0.08 - 0.3% U and it was not difficult to keep the exposure of workers well below regulatory limits. Furthermore, uranium milling has also been substantially free of occupational illness because environmental control has been generally satisfactory (l).The discovery of higher grade ore bodies in Canada has resulted in higher radiation levels in one mill and this has partly contributed to a need for increased radiation monitoring in the mill. In addition, as greater insight is gained on the effects of radiation, the implementation of the ALARA principle is being stressed at all mills.The concept of ALARA was emphasized by the ICRP (International Committee for Radiological Protection) in 1977 and stands for '""as low as reasonably achievable'"". It is based on the premise that no proven threshold for potential effects of radiation exists and that the actual individual exposure should therefore be kept as far below the regulatory limit as possible, economic and social factors being taken into account."

Jan 1, 1982

By Andrew Cormier

"The Early YearsThe Grand Lake coal fields in New Brunswick undoubtedly can claim the distinction of being the first part of North America from which coal was mined and exported. The diaries of the Governor of Massachusetts during the first half of the 17th century clearly establish this fact. There is also a reference in the Massachusetts Colonial Records which indicate that coal exports to New England were carried on as early as 1639.It has generally been believed that Cape Breton mined and exported the first coal; but no account has yet been found to show that this took place earlier than 1676. Both at Grand Lake and Cape Breton the coal was near the surface and removed by hand.When the country passed entirely into British control, Joseph Garrison, a grantee of Maugerville in 1765 moved to Jemseg. While surveying the north side of Grand Lake he discovered outcroppings of coal on the shore of the lake and further inland along the banks of streams. It was he who named Newcastle Creek in reference to Newcastle in England, which was widely known for its coal mines. Joseph Garrison died in 1783, the same year that an influx of United Empire Loyalists increased settlement in Newcastle Creek in the area now known as Minto. Many Loyalists also settled on the shores on both sides of Grand Lake.At a number of points where streams cut channels through the overlying strata, the coal seams were exposed and it was at such outcroppings that the early operations were carried on. A tunnel was driven in the seam from the foot of the bank, affording both an outlet for the coal and natural drainage from the workings. The coal was loaded into boxes and wheeled over wooden tracks to a point on the surface where it could be dumped into wagons and hauled either direct to destination or to where it could be loaded into boats and conveyed via Grand Lake, Jemseg and Saint John river to points of distribution.In the latter part of the 18th century and first years of the 19th century, farmers were undisturbed by mining the coal found on their lands. This was soon to change and resulted in many years of contention between landowners and the Legislative Assembly.New Brunswick became a separate province from Nova Scotia in 1784 and the seat of government moved from Saint John to Fredericton in 1788. The new province had its first priorities; the establishment of counties, the building of roads, and the development of its natural resources. From 1805, records of coal and land development are fairly complete. These records show the increasing interest of the Province in developing the coal fields. This interest resulted in the granting of coal leases to many friends of the government, without any regard for the wishes of the farmers who owned and had occupied the land for many years. The farmers fought back with lawsuits and other forms of dissension but with little success. By the end of the 19th century there were very few farm operators left in the area."

Jan 1, 1992

By Kim H. Shikaze, John R. Hawley

"Even though acid mine drainage is an old problem, particularly in coal mining areas, its appearance in the form of a major environmental hazard in the hardrock mining districts of Ontario was unexpected. The yellow and amber coloured wastes that characterize an acid mine drainage situation were first noted by the Ontario Water Resources Commission in the uranium mining Elliot Lake district. Problems of a similar nature were also noted in the copper-lead-zinc camp at Manitouwadge, the nickel camp at Sudbury and at numerous isolated base metal properties, both in and out of the Province of Ontario.Without exception, when acid mine drainage type effluents were evident, the specific companies involved worked sulphide or sulphide-associated ores. Without exception, the ore bodies contained quantities of iron sulphide (in various mineralogical forms) and, without exception, the milling circuits serving these operations were such that the iron sulphides were rejected to the tailings areas as waste.Once in a tailings area and after a varying period of time, iron sulphides react to form water soluble salts which, when discharged in the effluents from the tailings area, can affect stream chemistry and stream ecology.It is not unusual that the minerals pyrite, marcasite and pyrrhotite (all iron sulphides) react to form a stable oxide under atmospheric conditions. The law of stability of rocks and minerals, for instance, states that rocks and minerals are stable only in the environment of their formation and, as the environment surrounding them changes, the rocks and minerals tend to change to other species which are relatively more nearly stable under the conditions of the new environment (a). Under atmospheric conditions, iron oxide exhibits a greater stability than iron sulphide."

Jan 1, 1971