Search Documents

By Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the North American database.

May 1, 2006

By P. Lausch, Z. X. He, J. F. Archibald

"Documented underground fill failures have resulted because of the lack of adequate knowledge concerning fill strength and other physical parameters, as well as to a lack of consistent quality of fill materials being used by operators. On the basis of literature review and correspondence with backfill operators at 18 mines throughout the province of Ontario, non-systematic quality control procedures have been shown to exist, both within different levels of single operations and between separate mining operations, which act to provide inferior engineered fill materials and erratic application response in situ.Assessment of existing procedures set by mine operators for determining backfill physical parameters, and recommendation of optimum fill material testing and manufacturing guidelines are presented in this paper.A series of standard fill characterization test procedures are recommended to provide substantial, though not comprehensive, fill behaviour review. The purpose of these recommendations is to propose industry standards for backfill quality review. Data acquired could be utilized for fill design functions and as a means of comparing fill quality parameters between sites in a regular and more systematic fashion than is presently done."

Jan 1, 1993

By Jane Li, Kevin Tom

"Research has shown that broken rock on conveyor transport systems can contribute upwards of 50% towards the overall heat load in underground mines. However, few studies have made significant efforts to predict the temperature distribution of the ore and air simultaneously, which can help implement heat management strategies. The present investigation explores a transient, analytical heat transfer model to track ore-pile temperature distributions, along conveyor systems in an example underground mine. Production rate, ambient conditions, ore pile thickness and belt velocity are adjusted to evaluate the effect on dry and wet bulb temperatures.INTRODUCTIONWith an ever increasing demand on Earth’s resources due to a multitude of factors like population growth and step changes in technology, pressure on the mining industry to bring out more ore with improved margins is a persistent challenge. Typically, high-volume producing mining methods (i.e., exceeding 5000 tons per day (tpd)) such as sublevel and block caving, room and pillar, and longwall shall utilize belt conveyors instead of trucks as the primary haulage method to surface to save on operational costs (de la Vergne, 2014). However, studies have shown that when such material transport systems are installed at mine depths with virgin rock temperatures (VRT) above 40oC, the heat dissipated by the conveyed ore can account for over 50% of the underground heat-load (Pareja, 2000; Bluhm, Jones, Moreby, & von Glehn, 2012; van den Berg, Moreby, & Kok, 2015).Unlike other types of heat sources encountered in underground mines, such as diesel machines, strata, electrical devices, and autocompression, heat transfer by conveyed broken rock is much more difficult to estimate. The seminal work of McPherson (1993) states that broken rock heat transfer is a function of its surface area, and the air’s psychrometric condition. It is additionally a function of the VRT, its specific heat, production rate, heat transfer coefficient and the residence time (Bossard, 1997; Ross, Tuck, Stokes, & Lowndes, 1997). Consequently, few studies have attempted to analytically quantify the significance of ore heat flow."

Jan 1, 2019

By B. D. H. Knights, M. A. W. Bryson

Flotation of PGM ores, specifically UG-2, presents a number of technical challenges. These centre on the prevalence of chromite. Subject to over-grinding, chromite is primarily recovered to the flotation product through entrainment. This is of unique concern as it must be kept below a threshold for downstream smelting, with significant operational and monetary penalties being imposed should it exceed this concentration. A number of strategies have been developed to maximise PGM recovery in the presence of this unwanted contaminant. Specialised flowsheets form a vital basis and advanced control algorithms further enhance PGM recovery while minimising the recovery of chromite. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By Jean-Luc Collins

"This new tool can be used as a quick guide f or the assessment of the potential economic wealth of any risky capital project. It does provide an unambiguous recommendation of the type ""go or no go"" to the decision-maker simply by comparing two different ratios profit/investment. One ratio determines the minimum value required to at least break even while the other measures a probable value based on the asymptotic theory of statistical extremes.Its application is briefly illustrated by means of an underground gold mine extension project, an oil sands mine project and a polymetallic open pit project.Once a favourable recommendation has been obtained then a detailed ""cash flow after taxes"" analysis can be carried out for the project.IntroductionMany tools are used in financial decision-making such as the payback period, the discounted cash flow, the internal rate of return and the wealth growth rate (Berry , 1971).These tools are useful and meaningful in evaluating normal projects closely related to regular business where the number of assumptions made is usually very small and where the cost of capita! is usually selected as a discount rate or a hurdle value. In situations where a significant number of assumptions have to be made,two problems can emerge, namely:I. the risk involved is underestimated leading to a potential financial disaster; or2. a good opportunity is lost because the approach used in evaluating the project is too conservative.Each assumption has its own degree of uncertainty and it is well known that combining uncertainties together can lead to a total uncertainty of critical proportion. The easiest way to account for risk is to increase the discount rate or the hurdle value, but this approach alone is quite subjective and can easily lead to the problems described above."

Jan 1, 1993

By Phil Molloy

"In March, 1968, Skega Ruh her Liners were used to reline the shell of an 8' x 12' Allis Chalmers ball mill.This mill is used to regrind the cyanided pulp from 58i -200 mesh to 92% -200 mesh prior to this pulp passing to the flotation circuit, at approximately 450 tons per day.Before the use of rubber liners, the regrind ball Mill shell had been lined with single wave ni-hard liner!'. These liners had an average life of five years. Ni-hard end liners were used both prior to and during the use of rubber liners, as the life of the ni-hard end liners was about seven years, and it was thus felt that little economic benefit would be realized by lining the ball mill ends with rubber.The rubber lining used has a thickness of 57.15 millimeters and the square shaped lifter bars which are spaced at 14~ inch centres, have a 4"" x 4"" cross-sectional dimension.With the use of ni-hard liners, the consumption of 1 1/4 forged steel balls averaged 1.062 pounds per ton, Using rubber liners the consumption of l~"" forged steel balls increased to 1.368 pounds per ton. Also the level of the ball load which previously had been kept at approximately 18 inches below the mill discharge, had to be increased to approximately 8 inches below the mill discharge in order to effect the same grind.The initial gri4ding performance of the newly relined mill was also poor, until the leading edge of the rubber lifter bars, which were square shaped in cross-section had been worn to a rounded profile. These lifter bars were replaced after 4 years and 3 months of operation.The advantages of rubber liners in our opinion is as follows:"

Jan 1, 1974

The hydrometallurgical treatment of copper ores and concentrates continues to be an active field of innovation. The direct extraction of copper from ores containing chalcopyrite is an important development to provide an alternative to flotation-smelting and refining. Jetti Resources (with the University of British Columbia) and the JX Nippon Group have developed process options for chalcopyrite heap leaching. Biological heap leaching developments for chalcopyrite are also continuing in parallel. These direct leaching technologies are also very attractive for arsenical ores. The atmospheric leaching of copper concentrates is an attractive option along with autoclave processing. The Galvanox™ Process is the focus of commercialization by InCoR Galvanox Holdings under exclusive license by the University of British Columbia. The Galvanox™ Process can be used to treat chalcopyrite or enargite containing concentrates to high copper extraction with simultaneous precipitation of arsenic as atmospheric scorodite. FLSmidth has continued development of the Rapid Oxidative Leach (ROL) and associated technologies for chalcopyrite leaching. The Glencore Albion Copper Process using ultra fine grinding of copper concentrates and atmospheric leaching has found application in central Africa. The pressure leaching of copper concentrates continues to be attractive for rapid, complete oxidation of sulfide minerals with high copper extraction and arsenic stabilization of iron-arsenate minerals and precipitates. The Ecometales PLCC project is designed to use high temperature total pressure oxidation for treatment of an arsenical copper concentrate with use of existing copper SX-EW facilities for copper cathode production. The excess acid from the autoclave process will be used to make up the acid demand for associated copper ore heap and dump leaching operations. INTRODUCTION The recovery of copper from ores is dominated by the flotation of copper concentrates followed by smelting—converting and electrorefining. This process has been enabled by the development of froth flotation and progressively made more efficient by advances in smelting and converting technologies.

Jan 1, 2019

By P. G. Lazenby

This paper describes the latest instrumentation improvements in the INPUT Airborne E.M. System, particularly the new electronic signal-processing techniques. Several anomaly examples illustrating these techniques are shown.

Jan 1, 1973

By A. Putz, F. Vincent, A. R. Laplante

"This paper briefly reviews some of the gravity research done at McGill University and current Canadian operating practices, with emphasis on results of interest for operators. The following topics are addressed: security, economics, predicting recovery, circuit optimization, unit selection and final upgrading. Emphasis is placed on the Knelson Concentrator.The topic of security and economics are addressed jointly, in terms of the place of the gravity circuit in the mill flowsheet. Actual plant experience is drawn upon to identify potential problems and actual solutions.Predicting primary recovery is linked with a characterization of the ore, the choice of a circuit, and the fraction of the bleed used. Factors such as feed preparation, preliminary upgrading, fraction of recycle treated, ability to recover fines and location of the bleed are discussed.Final upgrading is achieved almost only by tabling and smelting. This can lead to fine gold recovery problems when more effective units are used upstream. Alternatives are discussed.IntroductionResearch on gold recovery by gravity over the past eight years has associated McGill University with a number of gold producers. This paper attempts to review the information gathered from a practical perspective. Some of the information was generated in McGill University's labs, some gathered at plant site, and some was shared by operators."

Jan 1, 1994

By C. Pichler, S. Luidold, C. Wagner, C. Sagadin, D. Kreuzer

Engineers and scientists have been combating the attack upon refractory materials of molten metals/matte and slags for hundreds of years. The details in many cases are still questionable or at least debatable. The corrosion is a major concern for furnace operators as refractory wear or failures inevitably results in reduced production efficiency and furnace reliability. Also the cost to industry is considerable and only a thorough understanding of all the complexities of the process will help to minimize that cost. One of the critical questions to overcome is the correct selection of refractories for the individual process steps to provide long and predictable refractory life together with high furnace availability. To understand the nature of the reactions involved in refractory corrosion, it is crucial to determine the complex thermo- chemical equilibria of the reactions occurring between the refractory materials and the process phases. A simulation model coupled with commercial software like FactSageTM is demonstrated aiming to understand the corrosion mechanisms between refractories and the molten process phases and draw implications for improving the performance of refractories and refractory lifetime. INTRODUCTION The extraction or recycling of valuable materials, e.g. metals, can be done by two main routes, pyro- and/or hydrometallurgical processing, depending on the chemical behavior of the used ore, scrap or pre-treated concentrate. Sometimes it is also necessary to use both process routes for the extraction or the recycling of valuable materials. In the case of a pyrometallurgical treatment, the usage of refractory materials is inevitable. This is mainly caused by high temperatures, prevailing during processing. The interaction between refractory material and slag, metal or matte leads to different reactions and interactions. As a main result corrosion of the furnace lining (refractory material) takes place. Hence, recurring furnace shutdowns occur for renewing the refractories. This leads to reduced production efficiency. Such refractory lifetimes are between some hours and decades, depending on the processes.

Jan 1, 2019

By L. Zhu, S. Kaierle, M. Dahmen, C. Zimmermann, T. Haubold, I. Kelbassa, C. Mattern

Application of integrally bladed disks (blisks) is of increasing interest in compressors of aero engines. Blisks are preferred due to their potential for size and weight reduction, for increased performance and for reduced manufacturing costs compared to conventionally bladed disks. In case of a damage the blisk aerofoils cannot be simply replaced. If the damage is beyond acceptance or blending limits refurbishment is possible only by scrapping the whole blisk assembly, or more cost effective by the application of advanced weld repair methods. Weld repair of blisk aerofoils is challenging as it affects a critical part with specific requirements regarding its mechanical integrity, and as the accessibility is usually limited. The paper describes the ongoing development of advanced weld repair processes as part of a comprehensive repair strategy which have been developed for small-sized blisk assembly to give competitive maintenance cost.

Jan 1, 2006

By D. Ofstie, B. Kargutkar

BIM, or Building Information Modeling, is transforming the way metallurgical facilities are built, operated and maintained. BIM provides a digital representation of the facility, complete with all physical and functional characteristics - enabling collaborative planning, concurrent design, construction simulation, sustainable operations and predictive maintenance through a connected information model. Building on experience gained in other industries, Hatch is aggressively applying the BIM process to the mining & minerals processing industry to address inefficiencies inherent in traditional document-based information management. Intelligent 3D models support real-time quantity forecasting and cost trending by commodity type and construction work package. By linking procurement and schedule data, material availability and constructability reviews are visualized to verify construction critical path, ensure work front safety and minimize craft downtime. The BIM digital information model connects engineering, construction, commissioning and vendor data, aiding timely asset-centric handover to plant operating and maintenance systems.

Jan 1, 2015

By K. Soucek, J. Ptácek, A. Hastíková, R. Kukutsch, P. Konícek, P. Waclawik

"Cable bolts are used frequently as a secondary support system (with steel arch support) in difficult stress-strain conditions of deep coal mines. The load transfer mechanism of cable bolts depends on several factors, such as the strength, deformation and geometric properties of the bolts, resin and the surrounding rock mass so-called cable-resin-rock system (CRR system). The bonding length and bolt/borehole diameter ratio strongly influence the final bearing capacity of the CRR system.The study presents the behaviour of CRR system during a pull-out test which is usually used in the carboniferous rock mass in the Czech part of the Upper Silesian Coal Basin. A series of 28 pull out tests were performed on 3-m-long cable bolts, with various combinations of borehole diameters and bonding lengths, to understand this behaviour. Boreholes were drilled into a solid rock mass consisting of fine-grained sandstone to guarantee similar conditions during the pull-out tests. Video inspection and measurement of borehole diameters were performed to determine their quality and real diameters. Three characteristics were observed from pull-out test results: ultimate pull-out load; displacement of the end of bolt and system stiffness. Numerical modelling by FEM (Finite Element Method) was used to determine the stiffness of the CRR system for variable bolt/borehole ratios and bonding lengths each under constant load. A linear elasto-plastic model and a mohr-coulomb model were used for cable and resin-rock respectively. The results of the experiment may contribute significantly to improving of the methodology of cable bolts installation as well as the design of used cable bolts."

Jan 1, 2015

By R. Llewellyn

"Wear damage is responsible for very high maintenance costs and significant production losses in the oil sands industry of northern Alberta.It affects all areas of operations and involves a panoply of wear mechanisms from low stress sliding abrasion at extremely frigid temperatures during winter mining, to elevated temperature erosion/corrosion in processes where bitumen is converted to lighter hydrocarbon products.There is no universal panacea to defend against such diverse attack and a wide selection of resistant materials and systems is employed. These range from relatively soft rubbers which rely on their elastic properties for their protective capability, to some of the hardest ceramics and cermets which are currently available commercially.Details are presented of the characteristics and forms of the variety of wear materials being used and how they relate to the requirements of their areas of application. The review focuses on the practices followed at Syncrude Canada Ltd., which is the larger of the two commercial oil sands plants."

Jan 1, 1997

By Mohamed Ourriban, Yongjun Peng, Qi Liu, Denis Cotnoir

"In the flotation of fine particles, there are two difficulties in general: low recovery of valuable minerals and high recovery of gangue minerals. The low recovery of fine valuable minerals is attributed to low bubble-particle collision and attachment efficiencies, while high recovery of fine gangue minerals is attributed to mechanical entrainment through water films between gas bubbles. Over the last five years COREM has been actively developing fine particle flotation techniques with the objective of improving fine particle flotation separation efficiencies.The fine particle flotation techniques with both generation of micro bubbles and enlargement of sizes of fine particles have been developed to increase bubble-particle collision efficiency. For oxidized fine sulphide minerals, both physical and chemical techniques have been developed to modify the hydrophilic surfaces and therefore increase bubble-particle attachment efficiency. To reduce mechanical entrainment of fine gangue minerals, a new approach, polymeric depression and flocculation, has been developed. By selecting the high molecular weight polymeric depressants to make fine gangue minerals hydrophilic and also enlarge their sizes, entrainment can be minimized. By combining these techniques, we are able to improve both flotation recovery and selectivity in some fine ore flotation systems.INTRODUCTIONWith depleting mineral resources and their declining grades, ores leaving grinding circuit for froth flotation are becoming increasingly finer to achieve mineral liberation. Together with the increasing demand for minerals, ever-increasing tonnages of fines are being produced. Therefore, flotation of fine particles is an immense challenge to be tackled by researchers all over the world today."

Jan 1, 2006

By Hiroyuki Sano, Hiroshi Chida, Katsuya Toda, Takafumi Sasaki

Saganoseki Smelter & Refinery is one of the largest copper producers in Japan to produce 450,000 tons of new copper annually. Saganoseki used to operate six PS converters with "4 Hot-2 Blow" scheme, but managed to change its operation to "3 Hot-2 Blow" scheme with four PS converters, while maintaining the same production capacity. To achieve the operational change, the following improvements have been carried out; 1) Extending service life from 220 to 350 batches, 2) Shortening cycle time by increasing the blowing rate and the matte grade, 3) Reducing environmental impact by applying sophisticated fugitive gas collection system and 4) Saving energy by waste heat boiler’s modifications. The operational change has been successfully executed, and results in drastic productivity increase and cost reduction. Currently, Saganoseki is maintaining the efficient and consistent operation with 4 PS converters. This paper describes the above-mentioned improvements for increasing productivity and the recent operational conditions of the PS converters.

Jan 1, 2015

By João Felipe Costa, Jair Carlos Koppe, André C. Zingano

Abstract - Traditional mine planning based on block models built with interpolation techniques such as kriging does not take into account the uncertainty associated with the estimates. These models are inadequate for short-range mine planning. In contrast, conditionally simulated models reproduce the actual variability (histogram) and spatial continuity (variogram) of the attributes of interest. Conditional simulation can be used to address the problem of measuring the uncertainty associated with an estimate. This paper outlines how the sequential Gaussian conditional simulation algorithm can be used to assess uncertainty of grade estimates and also illustrates how simulated models can be incorporated into mine planning and scheduling. A case study demonstrates the efficiency of the method in assessing risk associated with geological and engineering variables.

Jan 1, 2000

By R. W. Thompkins

"PREFACEPart 1 of this paper, published in the September issue, covered the occurrence of uranium, radiation from uranium ores, the uranium series, radioactive theory, radioactive equilibrium and application to the radon series, the working level, the theory of emanation and diffusion, transport by thermal diffusion of radon emanating from porous rocks, and definitions.The October issue carried Part 2, which dealt with radiation theory applied to uranium ores, other radon migration factors, factors affecting the radon gas release rate, the measurement of radon gas emanation rates, the tunnel concept, variation of emanation rate with grade and estimating radioactivity from grade analysis.Part 3, in this issue, concludes the series by discussing the techniques for controlling radiation and providing some example calculations.17.0. Techniques for Controlling Radiation17.1. Altering the Factors In the Diffusion EquationIt has been noted that radon gas emanates from the surfaces of exposed ore to the mine atmosphere. The diffusion laws establish the rate of this flow. The fundamental relationship is that the rate of flow (J) is a function of the pore concentration and the distance from the surface. It is expressed as: []If any of these terms is varied, either naturally or artificially, the rate of gas emanation will be altered.Altering the Diffusion CoefficientThe literature describes many ways to lower the radon gas emanation rates which are dependent on changing the diffusion coefficient:1. A layer of ice on top of a tailings dam or on a soil.2. Humid clayey materials and swamped soils over a radon source."

Jan 1, 1982

By Michel Aubertin

Using mine wastes as backfilling material for underground stopes has been a common practice for more than 60 years. Waste rock and tailings are used as filling materials because they are available at a reasonable cost to support the rock walls. Backfilling is also very advantageous because it reduces the amount of mine waste disposal on the surface. In underground mines, the backfill must first ensure stability of the opening, while increasing recovery of ore and minimising dilution. It is thus critical to accurately evaluate the pressures exerted on the walls and on the barricades placed near the base of the stope. In this presentation, existing solutions for evaluating the stresses on stope walls and barricades are briefly reviewed. The authors then present recently developed analytical solutions that take into account the stress transfer from the backfill to the walls in the stope and access drift. The stress state solution, which is based on arching theory, considers the influence of the stope geometry and barricade position within the drift. The method gives the pressure generated by partly or fully submerged backfill. The solutions apply shortly after backfill deposition, when the effect of pore water pressure cannot be neglected, and also for long term conditions under a fully drained state. Experimental testing and numerical modelling results are used to validate the proposed equations. Both numerical and analytical results show that the total pressure on barricades can be significantly increased by water pressure, while the effective stress is decreased (compared to dry or drained conditions). A discussion follows on the implications of the results for backfill applications.

Nov 1, 2008

By C. W. Eggert

This paper gives an account of the E.V.O.P. tests made at the Copper Rand mill of the Patino Mining Corporation in Chibougamau, Quebec. The runs were made to acquire an understanding of the method. A description of events, along with conclusions, observations and opinions, is out-lined.

Jan 1, 1967