Search Documents

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level position is then calculated from these pressure readings using an equation which includes the bulk density in the froth and bubbling zones. The precision with which the level is detected depends on how well these density values represent both zones. The calculation of these bulk densities from theoretical considerations is not possible and, therefore, the practice is to estimate them by calibration. Unfortunately, the calibration parameters often do not report the level with an acceptable accuracy. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the bubbling and froth zones. This probe can be used to detect the position of the interface to an accuracy of± 5 cm. The probe can be used while the column is in operation, which allows the on-line calibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 min diameter) are described.

Jan 1, 1989

By Michel Jebrak, Claude Bellehumeur

Regional and orientation geochemical stream sediment surveys were carried out by the Quebec Department of Energy and Resources in southwestern Quebec, over a part of the Mont Laurier Terrane of the Grenville Province. The area contains some small stratiform zinc deposits. The response of Zn mineralization to geochemical surveys is weak; the known mineralization is not dermed by anomalous samples and consistent patterns. This study uses a technique that increases the geochemical signature of Zn mineralization in filtering out geochemical background components related to lithologies and surficial conditions. The background variations were modelled using principal component analysis, and the filtering technique consists of the partial reconstruction of the data matrix from results of principal component analysis. The filtering procedure considerably enhances the Zn anomalies located in the catchment basins of Zn deposits, and defines some new anomalies in proximity to the marbles of the Mont-Laurier Terrane, the principal metallotect of Zn mineralization.

Jan 1, 1993

By Ginger Gibson

As an occupational culture, mining comes with its own set of rules, agendas and values. Yet mines often also operate in the traditional territories of indigenous communities, with whom specific agreements are negotiated that commit to respect culture, economy and environment. Mines in these locations employ extremely diverse workforces whose value systems often come into conflict in on-the-job relationships. Adaptation of individual worker attitudes and industrial operating culture thus both need to occur if there is to be the negotiation of a workable relationship. This paper will discuss ways that NWT diamond mines have adapted to their workforce, to ensure that rights and cultures of their diverse workforce can be respected. Historically, the concept of culture has been dealt with solely through the forum of ?cross-cultural? workshops. Gibson presents a model of a new type of ?cultural-engagement? workshop based on the top ten cross-cultural conflicts that actually arise at a remote mine-site. This model helps managers, team leaders, and workers to tackle in-mine conflicts that arise based on differing value systems of aboriginal and non-aboriginal workers and management. In addition, Gibson suggests that the concept of culture must be more rigorously applied throughout the mine structure and not discussed only in the forum of the cross-cultural workshop.

May 1, 2007

By Marcin Ziemski

This paper reports on an energy efficiency analysis completed as part of a research project looking at energy reduction opportunities in minerals processing operations. The plant discussed is a gold production facility owned by Newmont Gold in the Tanami region of central Australia. Due to its remote location, lack of nearby gas pipeline or power grid, the operation has been completely dependent on diesel fuel for its electricity generation and transport needs. The mine and processing plant use electrical power at a rate of 12MW to 18MW, resulting in a monthly electricity cost of over US$1.5M. The high cost of diesel combined with an impending power generation capacity shortage drove Newmont to undertake the energy efficiency study. An energy audit of the plant showed opportunities for significant energy savings through the strategic use of waste heat, fuel replacement alternatives and renewable energy sources.

May 1, 2007

By Jean-Marie Fecteau

The gold mine sector is presently facing low gold prices as well as technological challenges. Its competitiveness and survival will depend on new mining methods and equipment to improve ore extraction. In 1999, Natural Resources Canada has invested new funds over a period of three years at CANMET?s Experimental Mine to establish the Narrow-Vein Mining Project. A team of engineers and researchers specialised in mining, mechanics and electronics engineering are working to meet the critical need of ore-extraction technology. CANMET?s program in mechanisation and automation for narrow vein mining had, prior to 1999, realised several important achievements, many in co-operation with a consortium of mining companies (Soredem). The investment of new funds in this area will contribute to develop technologies to improve the productivity, as well as health and safety conditions of the narrow vein mining industry. Several important impacts of this project will be monitored. Specifically, a database of methods and equipment used in narrow vein mining is being developed. A key thrust is to identify operators? needs with respect to the development and automation of mining methods and equipment. Based on those needs, research and development projects will be created. The main problems identified following meetings with mine operators are described with a few elements of solution and the Web site created for the broadcast of the results is presented.

Oct 1, 2001

By David G. Almond

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations having large SAG mills fitted with variable speed drives. Problems associated with effective operation of this equipment has created the need for better operator knowledge of mill load behavior and the need for new instrumentation capable of providing accurate information about load movement and composition. This paper discusses two performance enhancing instruments available to address these needs.INTRODUCTIONThe economic demands of new mining projects has resulted in increased equipment sizes and this is particularly evident in milling where there are now many SAG mills operating in the range of 28’ – 40’ diameter with installed powers of 8 – 22 MW. These mills are designed to process very high capacities of ore daily2 and the variable characteristics of many of the deposits mined results in the need to vary the mill speed during processing to cater for the changes in ore hardness. Mill speed changes often result in operational problems associated with high-energy impacts striking the mill liners reducing energy efficiency as well as degrading the grinding media through breakage, accelerating liner wear and in extreme cases even breaking liners. These operational problems have given rise to the need to have instruments aimed at providing operators with accurate information in real time about the load composition and movement within SAG mills.The original concepts for operating SAG mills were derived from past experience of operation of conventional fixed speed ball mills. However, the relatively stable conditions that applies with fixed speed and constant ball charge in ball mills supports theoretical approaches to the grinding process based on energy calculations such as Bond’s Work Index concept. Later a set of parameters Si and Bij were used for describing load kinetics, but all of these methods neglect the details of load movement and how the energy is actually used inside of the mill. It is now commonly accepted as a basic rule that SAG mills grind by impact whilst ball mills grind by attrition and consequently SAG mills are designed and operated to generate a large amount of impacts by the cataracting load without paying sufficient attention to where these impacts are actually occurring. Many mills are operated on the basis that as long as the mill is consuming the expected power there is little attention given to the class of bodies using this energy and this often results in the inefficient use of energy."

Jan 1, 2005

By Jodi Wilding, Barry Lurnsden

The implementation of new technology to mineral separation operations requires rigorous testing to confirm the technology&apos;s technical and economic benefit. The Jaguar Mine owned by Jabiru Metals is located in Western Australia and sequentially separates a copper concentrate and then a zinc concentrate. Fine grinding (80% of zinc in tail is <25µm) is required to achieve efficient mineral separation. All mineral losses are therefore fine mineral losses, and so improvements in metal recovery must focus on this fine mineral. Magnetic aggregation technology has been shown to increase the recovery of fine paramagnetic minerals so it was an appropriate technology to evaluate at Jaguar. Testwork commenced in the copper circuit and it was found that there was a substantial reduction in copper in copper tail and an increase in zinc recovery to the zinc concentrate. The increase in zinc recovery in the latter zinc circuit was an interesting result and initiated the second stage of testwork that was to install and test a second magnetic conditioning unit in the zinc círcuit. This showed a further increase in zinc recovery. Magnetic conditioning technology has now been fully evaluated in the plant and is now part of the Jaguar flowsheet.

Jan 1, 2011

By J. Gustavsson, S. Holmin, Å. Afvander, E. Rosseland, E. Zimmerman

There are numerous advantages in replacing lead-based anodes with mixed metal oxide (MMO) coated anodes in copper electrowinning; for example, lower energy consumption, improved working conditions for operators and less environmental impact. Since 2012, Permascand AB in Ljungaverk, Sweden has evaluated Permascand coated titanium anodes in copper electrowinning pilot trials at Glencore Nikkelverk in Kristiansand, Norway. The investigation has proceeded in three different steps (Phase I, II and III). In Phase I, different Permascand coatings, electrode structures and coating methods were investigated. The results showed that improved current distribution, lower energy consumption and longer service life could be obtained with expanded mesh electrode structure in a box configuration compared to rod anodes in a single-mode construction. In addition, improved current distribution and less coating wear was found when electrostatic spray coating was used instead of brush (manual) coating. It was also found that the extrapolated service life from controlled lab experiments at 200 A/m2 was much shorter compared to what was experimentally obtained in copper electrowinning pilot trials at similar current densities. This was mainly attributed to different coating failure mechanisms in lab and industrial copper production. INTRODUCTION Traditionally lead-based anodes have been used in copper in electrowinning due to lower cost. But there are many advantages in replacing lead-based anodes with mixed metal oxide (MMO) coated titanium anodes in copper electrowinning, such as lower energy consumption, higher corrosion resistance, improved working conditions for operators and less environmental impact. Still, many facilities are using lead-based anodes, although the progression of using metal oxide coated anodes in copper electrowinning has slightly increased (Robinson et al., 2012).

Jan 1, 2019

By R. A. Lunceford, K. C. Shaver

Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km

Jan 1, 1998

By D. Naden, D. J. King

"The high capital and operating cost of liquid-solid separation circuits in hydrometallurgical plants has led to an increased focus on the use of in-pulp systems for metals recovery in order to eliminate the need for solids washing and to reduce the need for liquid-solid separation.Carbon-in-pulp (CIP) has now been accepted in Canada and around the world as the leading process for recovery of gold and silver, replacing the Merrill-Crowe process and thus removing the need for CCD thickeners or belt and drum filters. The overall design of conventional CIP adsorption circuits was established in the late 1970s and it has remained substantially unchanged until now. Most of the development work since 'hen has been concentrated on improving methods of separating pulp and carbon and on reducing carbon losses during transportation and agitation.Resin-in-pulp (RIP) has been used for many years in uranium mills in the USA. However, most of the plants were built in the 1960°s and RIP was only chosen when liquid-solid separation of leach pulps proved very difficult. The plants are far from ideal as they have high resin losses and high maintenance costs. Consequently, there is room for improvement.Davy McKee has taken a fresh look at the engineering development of in-pulp contactors leading to a fundamental redesign of the adsorption units. The improved in-pulp technology uses a modification of the proven air-swept screen techno1ogy together with a new technique of process operation. The new contactor operates at high pulp throughput rates with high concentrations of carbon or resin in the recovery stages, resulting in a significant reduction in the contactor size over conventional design. As a result of this reduction in the size of the contactor by up to 80%, significant savings can be made in equipment and building costs. In addition, the plant 1s easier to operate than a conventional CIP plant."

Jan 1, 1987

By M. G. Lipsett

"The Mining Information Technology User Group considers information to be a strategic enabler to improved business performance in mining. This ad hoc group has been meeting since 2000 to share knowledge and leverage their efforts in effectively using IT in mining. In this paper, core issues to mining IT are reviewed, along with initiatives to engage industry professionals and decision-makers in the potential for improved use of information in their operations. Relevance of IT to Canadian MiningMining operations always drive to improve their performance, and so far they have succeeded by using different technologies. While economies of scale have come in fragmentation and material handling, and energy usage has improved through conservation and design of integrated mineral processing plants, these systems have the net result of tightening operational constraints, through reduced excess capacity. There are higher opportunity costs of lost production when integrated, large-scale systems are operating in a sub-optimal way.The problem is that it is profoundly difficult to run a mine in an optimal way. Optimization requires a defined objective function (e.g., profit), which is hard to pose, let alone solve, because so many inter-related aspects of an operation affect the bottom line. Even for a small, well-defined process state, it is difficult to measure all the pertinent information with sufficient accuracy to ensure that the system is performing well in real time.The art of mining remains making good decisions with uncertainty: in the orebody delineation; in the allocation of resources; in the efficiency of the operation; in the reliability of components and systems; and in responding to the downstream market. As well, individual decision-makers need to know how their decisions affect other processes and systems, so that improvements in one part of an operation do not result in such degraded performance in the rest of the plant that overall profitability goes down."

Jan 1, 2003

By A. Brown

THIS P APER has been pre-pared as a progress report on Mines Branch investigations into problems of ground stress in certain co al mines of Western Canada. As such, it should be considered as a companion report to the one ( 1) presented to the Mining Society of Nova Scotia in 1956 and which dealt with similar investigations in the coal mines of Eastern Canada. For the past 50 years, dynamic incidents in the form of &apos;bumps&apos; and &apos;outbursts&apos; have been occurring in the coal mines of the Inner Foot-hills belt of tl1e Canadian Cordillera. As these phenomena generally become more frequent with in-creased thickness of overburden, a limiting depth of mining of 2,500 feet has been set (2) for estimating recoverable reserves of coal. If such a view were accepted, from a long-term viewpoint very large resources of coking-grade ?coal -in a part of the continent deficient in such coals -would not be available to the nation. The terrain in which these in-6dents take place may be described in geological terms as being dominated by pronounced structure in strata ?consisting of a large proportion of highly indurated rocks. The Geological Survey of Canada has co-operated by carrying out structural studies (3) at the mines, supplemented lithological by stratigraphic observations.

Jan 1, 1958

By R. A. Price

The base of the biozone of Olenellus is accepted as the most universally applicable criterion for defining the base of the Cambrian System. The use of this definitive criterion is restricted by important practical considerations. In the southeastern Canadian Cordillera this zone appears to truncate the basal ortho-quartzite of a west to east marine -transgression. This transgression began in Interior British Columbia in the Late Proterozoic and terminated in the region of the present Rockies in the Late Waucobian. Most of the material deposited by the transgressing sea originated in the eastern positive element &apos;Laurentia&apos; and was transported over the intervening low Proterozoic-Windermere erosion surface. The configuration of the advancing shoreline and the distribution of the sediments were controlled by the tectonic activity of positive elements in northwestern Montana (Montania) and in the Fairmont Hot Springs-Radium area of British Columbia.

Jan 1, 1956

By Sean Dessureault

Information technology (IT) initiatives in the past have tended to be sold on their ability to maximize resource output and return on capital by using assets more effectively and efficiently. Many IT projects fail, not delivering return on their investment. This is known in the IT industry as the ?productivity paradox,? where increasing investments in IT do not result in comparable increases in productivity. Experiences and studies of most business sectors reveal that this paradox is rooted in the false assumption that more IT spending automatically results in financial benefit, whereas the true source of benefits is in how effectively IT is used. Most business sectors have accepted that the reengineering of processes is required to gain the full benefits promised of IT. A mining operation has organizational processes similar to most business sectors but unique operational processes. The lessons of changing business practice in more common business processes such as inventory control and customer-supplier relationships can be adequately transposed into a mine. The unique operational processes in mines, in turn require unique redesign efforts. Several enabling information technology opportunities have recently become available, such as more integrated mine production management systems and tactical manger training simulators. This paper reviews the latest IT products and ou lines the processes and kinds of change that will be required in order to benefit from these new investment options.

May 1, 2002

By Y. Nara, N. Aramaki, M. Maruyama

Evaluation of three dimensionally non-uniform strain distribution in rocks under various conditions such as in water or under freeze-thaw cycles is of significant importance to understand their complex deformations and fracturing mechanisms. For this purpose, we developed an image analysis method which can evaluate or “measure” the three dimensional (3-D) strain distribution in rocks. The proposed method utilizes the 3-D images of rock under initial and deformed configurations, which are obtained by some imaging techniques such as X-ray computed tomography (X-rayCT). In the proposed method, the obtained 3-D images are divided into multiple sub-regions of interest. For each sub-region, the strain is evaluated utilizing 3-D affine transform with unknown coefficients to be determined. In the first step, 3-D voxel level displacements at multiple representative points in each sub-region are computed by 3- D digital volume correlation technique between the comparison images and the initial-guess of the transform coefficients are obtained. In the second step, referring to the initial-guess of unknown transform coefficient, they were optimized in sub-voxel level by finding optimum digital volume correlation between the comparison images, which can evaluate the transform coefficients with higher precision. From the calculated transform coefficients, the strain was directly obtained through the spatial derivative of displacement based on affine transform. In this paper, along with the description of the proposed method, the evaluation of deformation in a lignite specimen due to immersion in water was presented as an application example. As the 3-D imaging technique, micro-focus X-rayCT was applied. The result showed that the induced dilatational strain field due to the initiation and extension of cracks in the specimen was clearly captured. Therefore, authors believe that the proposed method can be applicable to various problems in rock mechanics.

Jan 1, 2015

By W. G. Mine

In September, 1953, seismographs were installed in the Crowsnest Pass area of Alberta and British Columbia to study the &apos;bumps&apos; which were occurring in the coal mines at Fernie and Coleman, and to investigate the possibility that they might be related to minor earthquakes in the area. During the initial phase of the work, three seismographs were operated at widely separated stations, two in the region of coal mines at Coal Creek and Coleman and one at Turner Valley, distant from any mining operations. Some earthquakes were recorded at all three stations and, in addition, many small disturbances were recorded by the seismographs located near the mines, especially -by the instrument at Goal Greek. A closer network of radio-linked seismographs was then in-stalled near Fernie, the records of which definitely established that the small disturbances were occurring in the mine workings, both active and inactive. No relationship was established between bumps and local earth-quakes in the area. This work was initiated as a -co-operative effort with the Fuels Di-vision of the Mines Branch, Department of Mines and Technical Surveys, which has undertaken a study into the phenomena of ground stress relief in underground mine workings.

Jan 1, 1958

By L. P. Chrismas

"IN 1975, Nova Scotia produced 1.8 million tons of coal with a FOB mine value of $47.6 million. Of this total, about 30 per cent or 600,000 tons was coking coal and the remainder was steam and industrial-grade coal. The Nova Scotia Power Corporation consumed 630,000 tons in three generating stations and 570,000 tons were sold to Sydney Steel for making coke for its steel operations. Exports, principally to Great Britain, comprised 370,000 tons in 1975 in addition to the 300,- 000 tons shipped to other provinces for use by cement and pulp and paper companies. In 1975, just over 100,000 tons of coking coal were imported into the province from Alberta. Before 1975, low-volatile coking coal was traditionally obtained from the United States. In 1975, production came from seven individual mines and one project involving reclamation from mine dumps in Pictou County. Of the seven producers, four are owned by the Cape Breton Development Corporation, a federal Crown corporation; the remaining three are small independent mines, but, even though small, they are sizeable contributors to the economies of their local areas. After 101 years of continuous operation, Devco's Princess mine was closed in 1975. The Nova Scotia coal industry, in terms of value, accounted for about half of total mineral production in 1975. The industry provides jobs for 3,000 men and women. It is also significant that in 1975 Nova Scotia produced about 6.5 per cent of Canada's total coal production of 28.3 million tons. Detailed statistics on Nova Scotia's coal industry appear in the Appendix."

Jan 1, 1976

By A. E. Wraith, J. Protheroe Jones, P. J. Mackey

INTRODUCTION When Victoria became queen in 1837, that technical wonder of the 19th century—electricity— had progressed from being an exciting physical curiosity and was now a field of intense scientific investigation, invention and application. Its role in electrochemistry had been brilliantly quantified by Faraday in 1833–1834, and his earlier discoveries in electro-magnetism were to lay the foundations of electricity generation and the electric motor. In this age of electrical experiment, silver electro-plating emerged as a popular decorative art, at first using batteries to provide the deposition current, superseded by dynamos in the early 1840s. The decorative chemical and electroplating of precious metals was largely pioneered in England by the firm of G.R. Elkington and Co., founded in Birmingham by George Richards Elkington (1801–1865) in 1832, and protected by a series of patents which helped the company establish a leading position in the new field of ‘electrometallurgy’. In the same decade, the technique of electrotyping emerged, the first application of electro- forming by electrolytic deposition. Simultaneously invented by Spenser in England and Jakobi in Russia, but generally claimed for Jakobi, electrotyping involved plating a thick copper layer on to an electrically conducting mould wall embossed or incised with a pattern or profile which would consequently be replicated on the copper deposit—essentially a method of casting by electro-deposition with the mould wall as cathode. Woolrich’s invention of the low voltage magneto-dynamo in 1842 eliminated the need for batteries as a continuous source of deposition power, opening up the possibility of making more massive electroplated deposits, and by the mid-point of Victoria’s reign in 1869, the work of Wilde, Wheatstone and Siemens had produced the self-excited electro-dynamo, capable of higher voltages and yet greater deposition power. In this early Victorian period copper was extracted and refined by methods which had developed step-by-step over many decades. Only relatively rich copper ores containing more than, say, 6% Cu were economically useful, and the final copper product was far from pure. Copper production in Britain was located principally in the Swansea area of South Wales, based upon the ‘Welsh process’ of reverberatory batch smelting and refining, using locally mined coal and ore imported from Cornwall and elsewhere. Silver was an important by-product. Much of the output was exported and South Wales remained a principal supplier to the world copper market until the 1890s. It was here at Pembrey, a few miles west of Llanelli, that a new primary copper smelter was stablished in 1849 under the name Mason and Elkington, arguably to supply the Elkington company’s market for electrotype products.

Jan 1, 2019

By J. Palarski

In the Polish coal mining industry, the use of mine waste in underground backfill has been the most common means of providing ground support to minimize surface subsidence, increasing extraction ratios, and reducing the quantity of waste for surface disposal. Over the last decade attention has been focused on the use of different waste as filling material of underground workings and grouting of roof fall rocks in caving area. In the paper, a brief history of the development of fill technology in Polish coal mining industry is presented. Next, the paper discusses various criteria that should be taken under consideration in the preparation process of a fill slurry and grout, fill distribution systems, mining geometry and placement methods. Moreover, in the paper evaluation of the potential of utilizing coarse and fine waste as a resource material in the production of a backfill slurry and grout for filling and injection in abandoned mines is presented.

May 1, 2007

By F. G. Vetsch, F. A. Ronaghan

"Introduction1N THE FALL of 1951, Peace River Allied Fort St. John No. 1 well was drilled in Lsd. 1, Section 9 Township 83, Range 18, West of the 6th Meridian, on the flats of the north side of Peace river, six miles southeast of the village of Fort St. John, B.C. During this operation, non-commercial shows gas in three zones and of oil in one zone were obtained during the drill-stem tests. Further geological study indicated that this well was on the southeastern edge of the Fort St. St. John structure.Pacific Fort St. John No. 4, drilled shortly afterwards, obtained possible commercial gas flows on drill-stem test in five zones and thus encouraged development of what has become Canada's largest multizone gas field.In general, the productive horizons in this area possess fair per-meabilities and high porosities, a combination which provides for high reserves and moderate productivities. Development to date has therefore stressed experimental techniques in drilling and completion practice to provide high deliverability wells.Data and information of a specific nature apply, in all cases, to the pools in the Fort St. John structure."

Jan 1, 1954