Search Documents

By Leopoldo Gutierrez, Sergio Castro, Lina M. Uribe, Janusz S. Laskowski

"The effect of sulfite and metabisulfite ions on the amyl xanthate flotation of copper-activated pyrite, in distilled water and seawater, has been studied by micro-flotation tests and redox potential measurements. The activation of pyrite was carried out varying copper ions concentration. It was found that in the presence of copper ions in solution, sulfite and metabisulfite are able to depress copper-activated pyrite at neutral or slightly acid pH. After the addition of sulfite or metabisulfite ions the resulting pH is more acidic with metabisulfite ions. A significant increase of the redox potential of the solution was observed as copper ions concentration increased. Then, the initial reducing conditions brought about by sulfite and metabisulfite ions, change abruptly to oxidizing conditions in the presence of copper ions. Under these oxidizing conditions, the metabisulfite showed to be an effective depressant for pyrite mainly in seawater. However, sulfite was a pyrite depressant in both distilled water and seawater. Based on these results, the pyrite depression by sulfoxy-depressants during the flotation of Cu/Mo ores in distilled water and seawater is discussed.INTRODUCTIONDepression of pyrite by sulfoxy-depressants (sulfite and metabisulfite) in the presence of copper ions is an important issue. This is particularly true when pyrite depression in the flotation of Cu/Mo sulfide ores is carried out in seawater. The use of lime in seawater must be avoided because the formation of magnesium hydroxy-complexes and precipitating magnesium hydroxide strongly depresses molybdenite flotation (Castro et al., 2014). In order to solve this problem, one large plant in Chile uses sodium metabisulfite (MBS) instead of lime to depress pyrite in seawater. In plant practice, this also improves molybdenite flotation since with the use of MBS the pyrite depression is carried out at pH 6-7, instead the pH 11-12 usually employed with lime.From a general point of view, pyrite exhibits some natural floatability over acidic pH ranges and may be partially floated without thiol collectors (a coating of sulfur/polysulfides has been claimed). Therefore, pyrite flotation with xanthates is usually high in the acidic pH region, but decreases greatly at alkaline pH (Leppinen, 1990; Fornasiero and Ralston, 1992; Zhang et al., 1997)."

Jan 1, 2016

By N. Parnian

"Carryover of caustic soda (NaOH) in the steam path caused catastrophic failure of superheater 304H stainless steel tubes in a steam generator and led to an unexpected shutdown after just five months of continuous service of petrochemical following the start of production. The cause of the failure was studied, with a focus on the formation of sigma phase in the weld joint and effect of caustic embrittlement on stress corrosion cracking (SCC). The cracks were examined at the seam weld, heat affected zone (HAZ), and Ubend areas. Hardness was measured for the base metal, HAZ, and weld metal, and microstructures were examined using optical microscopy and scanning electron microscopy (SEM). Crack initiation is attributed to gouging on the precipitated carbide at the HAZ and also the formation of sigma phase in the weld metal, as shown by energy dispersive X-ray (EDX) analysis. In addition, cracking was propagated by caustic embrittlement because of residual stresses and hammering. Finally, the characteristic feature of fracture was illustrated by SEM fractography, and consists mostly of intergranular SCC and some quasicleavage transgranular. INTRODUCTIONThree key factors are needed for the initiation and propagation of intergranular stress corrosion cracking (IGSCC): a susceptible material, a corrosive environment, and sufficient stress. Although austenitic stainless steels are susceptible to sensitization and IGSCC, they are widely used in boiler and superheater tubes because of their high corrosion resistance, high oxidation resistance, acceptable mechanical characteristics at elevated temperatures, and low cost.Sodium hydroxide is injected to neutralize acidic constituents in the steam path, but caustic can concentrate in boiler tubes and attack the surface metal (known as gouging) even traces of caustic in the steam can deposit on surfaces and cause local concentrations of several percent (ASM handbook, 1992). Not only sensitized grains but also sigma phase formed in the weld metal can initiate caustic cracking. In this research, the cause of the failure of 304H stainless steel superheater tubes in a methanol petrochemical plant in Iran was studied with a focus on the effects of caustic embrittlement on IGSCC."

Jan 1, 2012

By R. W. Lawrence

"In the past year, BioteQ Environmental Technologies Inc. have initiated design and construction of new plants to add to an existing list of plants that utilize the BioSulphide® and ChemSulphide™ process technologies for metal recovery and water treatment. In these plants, low cost biogenic sulfide or, in some cases, chemical sulfide reagent is used to selectively remove metals from contaminated water. The process produces high grade, marketable, metal sulfide products even from low grade feed solutions. The revenues generated from the sale of products can allow for water treatment at a profit in some cases, offset treatment costs in others, and generally reduce sludge disposal and management costs. The effluents produced from the process can meet stringent environmental standards. Current plants in operation and under construction range in sulphide demand from 50 kg/day to 3.7 tonnes/day, with the feasibility of larger plants with sulfide demands ranging from 6 to 43 tonnes/day under review.Biogenic sulfide reagent can also be considered for other applications in hydrometallurgy and mineral processing. Uses under consideration by a number of mining companies include: (1) replacement of sodium hydrosulphide in the SART process for cyanide regeneration and copper recovery in the processing of gold-copper ores, and (2) replacement of sodium hydrosulphide for use in the separation of copper and molybdenum in flotation. Biogenic sulphide, produced on demand at site, offers significant cost savings and provides the additional benefit of improved safety due to the elimination of the transportation, handling and storage required for chemical sulphide reagents.This paper reviews the applications of the BioSulphide® and ChemSulphide™ technologies for water treatment and metal recovery, and introduces projects where biogenic sulfide can be applied in hydrometallurgy and mineral processing."

Jan 1, 2007

By F. Parada Luna, F. Parada Torres, J. Salvo, A. Reghezza

In the pyrometallurgical processes of copper concentrates, arsenic is preferentially concentrated in the dusts carried by the gases as a result of their volatility and subsequent condensation in the gas cleaning train. In this work results obtained by alkaline leaching of the dusts from Ministro Hales roasting plant, belonging to Codelco, are presented. For the Ministro Hales plant the alkaline leaching would be an alternative to the recirculation of dusts to the roasting furnace. The experimental study considered NaOH and NaOH plus NaHS leaching of two samples of dusts, with 4.24 and 2.55% arsenic respectively. The results show that it is feasible to extract 90% of the arsenic and 50% of the antimony at room temperature using only NaOH, and when the temperature increases to 95ºC, the extractions of As and Sb increase. Copper remains in the solid residue with less than 1% dissolution, and the NaOH net consumption was approximately 140 kg/t of dust. In leaching tests with NaOH + NaHS, two types of methods were tested, baking plus leaching with water and direct leaching with a NaOH+NaHS solution. With the second method arsenic extraction increased to 95% and copper dissolution was less than 0.01% at 85ºC, NaOH 100 g/L, NaHS 90 g/L, 1.5 h and L/S ratio of 5/1 (L/kg). The bismuth remains stable in the solid in all cases. INTRODUCTION The presence of arsenic in copper concentrates has increased with time and the environmental regulations are becoming increasingly more stringent. In concentrate treatment pyrometallurgical plants, most of the arsenic is volatilized condensing in the gas train and is collected along with the entrained solids to form the flue dusts. Under these conditions, in smelters of copper concentrates with high arsenic content, the dusts are being treated in hydrometallurgical plants to extract and stabilize the arsenic, which also means that most of the copper contained in the dust is co-extracted with the arsenic. This affects the recovery of copper in the smelter and an alternative such as the selective alkaline leaching of arsenic, would allow the copper from flue dust to be recovered.

Jan 1, 2019

By V. L. Gravitis

Radioisotope X -ray techniques of analysis for nickel have been tested in laboratory and plant trials. In the laboratory tests. a comparison was made of radioisotope and conventional analyses for nickel in solid s samples taken from streams of a nickel concentrator. Coefficients of variation of 1.7% for feed and concentrate samples , and equal to 10% for final tailing samples, were obtained. Continuous determination of nickel in final tailing slurries was demonstrated in a trial lasting 20 days at a nickel concentrator (Western Mining Corporation), nickel being determined with a standard error of 0.036% Ni in the slurry solids within the range of 0.24 to 0.68% Ni. This error, obtained by comparison of on-stream probe analyses with assays of samples taken from the stream, includes errors in sampling and assay by conventional techniques.

Jan 1, 1977

By James A. Brown, Marius Botha, Christopher A. Fleming

"The technical and economic feasibility or re-processing hundreds of millions of tons of tailings in a number of historic gold tailings dams in the Witwatersrand area of South Africa is being investigated. The objective is to recover uranium and residual gold from the tailings, as well as to oxidize the sulphides to eliminate long term environmental liabilities associated with acid mine drainage. The tailings from the re-processing plant will be re-deposited in a new area far from urbanization, allowing for the rehabilitation of the real estate currently occupied by these historic tailings.The first step in the process involves a mild-regrind and mild acid leach of the tailings (pH 2.5 to 3.0) to dissolve up to 40% of the uranium. This uranium is recovered directly from the pulp by resin in pulp (RIP) with a strong base resin. The RIP tails are then treated by flotation to recover a rougher pyrite concentrate, and flotation tailings that are discarded. The rougher concentrate is cleaned to produce a final pyrite concentrate and cleaner scavenger tailings, and the pyrite concentrate is oxidized in an autoclave to leach uranium and generate acid. The autoclave discharge is combined with the cleaner scavenger tails, and the acid and ferric ions generated in the autoclave are used to leach more uranium and oxidize more sulphide in the cleaner tails. The product from the concentrate leach circuit is processed by resin in pulp for uranium recovery, followed by neutralization, cyanidation and carbon in pulp for gold recovery.The rougher float tails may be further treated to recover gold that was not recovered in flotation, but which had been liberated from the old dumps by natural oxidation of some of the pyrite over many decades. The float tails would be neutralized and treated by cyanidation and CIL to recover this liberated gold.All parts of the flowsheet have been extensively tested in the laboratory, and the critical elements of flotation, pressure oxidation and resin in pulp have been demonstrated in pilot plants. The results of the hydrometallurgical investigations are presented here."

Jan 1, 2010

By M. M. Hajdasinski

"Any study in the field of theoretical investment analysis, or practical project evaluation, must be based on the assumption of one of the commonly applied models of time and value representation, and the corresponding interest convention. The lack of clear assumptions in this regard may easily confuse both the author of the study and the reader, and sometimes even lead to inaccurate results.In the first part of this paper formal definitions of the continuous and discrete models of time and value representation are introduced; in the second part, the importance of transparent assumptions is shown using a concrete example of inflation calculation in project evaluation.IntroductionIn his recent paper, L.D. Smith(10) discusses an important aspect of mine investment analysis: inflation in project evaluation. His interesting presentation of current practices of handling inflation by Canadian and international mining companies in their feasibility studies ends, in the conclusions, with a call for clear assumptions made when evaluating mining projects.With this call, an important issue has been addressed. The lack of clearly stated assumptions, or their incompleteness, are relatively frequent with regard to the interest convention or the model of time and value representation assumed when evaluating mining projects. It is, for example, fairly common that the quantitative evaluation of a project is performed according to the discrete model of time and value representation and the discrete interest convention, and the graphical presentation, supporting this evaluation, reflects the continuous model.Sometimes such an ambivalency means nothing more than just a formal inconsistency; there are cases , however, that may well lead to a serious confusion and /or to inaccurate results . Before this can be demonstrated on a specific example, a concise description of the models of time and value representation used in the evaluation of industrial projects seems to be in order. Although these models (especially the discrete one) have been in common use in the research and practice of financial analysis for considerable period of time, they have been applied rather intuitively, and their forma] definitions are difficult to find even in the standard textbooks on Engineering Economy."

Jan 1, 1990

By Joo Hyun Park, Hyun-Sik Park

"Gold is one of the most valuable and precious metals. But, the extraction efficiency of gold from natural resources is very low and labor-intensive due to very low concentration of gold, i.e.,1–5 ppm, which means that gold extraction processes produce extensive amounts of tailings. The gold content in printed circuit boards (PCB) from waste mobile phones is about 100 to 400 ppm, which is enormously greater than the concentration found in natural ores. Consequently, processes for recycling waste PCB and gold mine tailings become of increasing importance to maintain a sustainable society. As processing these waste materials by pyrometallurgical methods has become more economically attractive, understanding the thermodynamic behavior of gold in smelting slags under oxidizing and reducing conditions has become increasingly important. Therefore, in this study, the effects of slag chemistry, oxygen potential and temperature on gold solubility in smelting slags are discussed. From the results presented, the predominant species of gold is strongly dependent on the basicity of slag. Furthermore, more basic slags showed higher solubility of gold at a given oxygen partial pressure, and more oxidizing atmospheres enhanced the dissolution of gold to the molten slag phase. As a consequence, careful control of the slag composition during pyro-processing of gold-containing waste materials is required to maximize gold recovery. INTRODUCTIONGold has good physicochemical properties. Thus, it plays an increasingly important role in industrial applications. For example, over 300 tons of gold are used annually in electronic components (Hageluken &Corti, 2010).However, 75% of all gold ever produced has been extracted since 1910 and gold reserves in the world are becoming rapidly depleted (Louis & Pluchery, 2012).The cost of gold production and its price in the market have increased rapidly during last 20 years as shown in Figure 1, and interest in the recycling of gold-containing materials has naturally increased.The wastes from electronic equipment (e-wastes) contain large amounts of precious metals compared to their own respective ores, and therefore such wastes may be considered as a secondary source of valuable metals. For instance, the concentration of gold in natural ore is commonly 0.5–15 g/ton-ore (0.5–15 ppm), while its concentration in electronic circuit boards is over 10 times higher, typically being about 150 ppm in expansion cards and over 10,000 ppm in central processing units(Barbieri et al., 2010).Also, gold mine tailings are discharged after the flotation process as slurry form then stored near the operating plants (approx. 100 ton per day in one Korean gold mine). Gold mine tailings contain gold at about 1–2 g/ton. This is the reason why Au-containing materials such as e-wastes and mining wastes are highly important sources of gold (Yamasue et al., 2009)."

Jan 1, 2017

By R. Luchese de Moraes, J. A. Matthews, C. Feliciano Bruzual

The role of biomass char in blast furnaces has been re-examined by scientists worldwide, as a feasible option to reduce the carbon intensity of ironmaking. This contribution makes a technical and economic analysis of the ferro gusa industry in Brazil, with the last 172 charcoal-Blast Furnaces operating in the world. A key strategic question is presented: what is the current status and future prospects of biomass use in Blast Furnaces? Findings provide significant implications to metallurgists: while ferro gusa from charcoal is regarded as carbon neutral iron with low impurities, there are limiting factors that hinder the further proliferation of charcoal-BFs: biomass generation requires vast extensions of arable land and aggregates have low production capacity. Additionally, most of the charcoal is presently generated in beehive kilns with low yields. These elements combined make charcoal-hot metal expensive in price. With respect to the future prospects of biomass, the injection of small biochar particles through the PCI rigs in BFs (here coined Bio-PCI) and iron ore sintering may offer a practical alternative to significantly reduce the CO2 emissions in the ironmaking process.

Jan 1, 2015

By M. Nakai, G. Itoh, R. Yamada, A. Kurumada

In order elucidate the mechanism for poorer fatigue properties of 7000 series aluminum alloys than those of 2000 series alloys, the effect of the test environment on the fatigue crack growth of the two series alloys was investigated, considering the relationship to hydrogen embrittlement. Two 7075-type and four 2024-type alloys were T6-tempered and T4-tempered respectively, and subjected to fatigue crack growth tests in moist and dry environments. When tested in moist air, fraction of intergranular crack path was higher in the 7075-type alloy with coarse equi-axed grains than in the 2024-type alloy with similar microstructure. This was in accord with the larger crack growth rate in the 7075-type alloy. Both the intergranular crack path fraction and the crack growth rate were decreased by changing the environment to the flow of nitrogen gas. Thus, the large fatigue crack growth rate of the 7075-type alloy is attributable to hydrogen embrittlement.

Jan 1, 2015

By Antônio Peres, Rogério Guimaraes, Lauro Takata, Harold Wyslouzil

"Serrana’s concentrator, in Araxii, has capacity of producing approximately 800,000 tomes of phosphate rock per year, with a P205 grade of 36%, from ores grading between 13% and 14% P205. The annual mining rate is around 3.5 Mt and the apatite is concentrated according to the following sequence: crushing, grinding, desliming, flotation and low and high intensity magnetic separations.Two industrial flotation columns (3.0 m x 4.5 m x 14.5 m) were commissioned in 1993 as a replacement for circuits of barite and apatite fines flotation. In 1994, four additional flotation columns of the same dimensions were put into operation, replacing 42 Wemco mechanical cells (300 ft3 each), in the barite pre-flotation, coarse apatite (two columns) and tailings regrind flotation Circuits. Overall, 66 mechanical cells (300 ft3 each) were replaced by only six flotation columns, designed by Cominco Engineering Services Ltd - CESL.The present paper describes the stages of process development, pilot plant testwork and implementation of the industrial project, highlighting the most relevant aspects of each of them. The results achieved are related to improvements in flotation selectivity, gains in P205 recovery and better process control, resulting in better quality products and lower production costs. Other benefits included a decrease in flotation reagents, electrical energy and maintenance materials consumption. These factors contributed to a significant decrease in the cost of phosphate rock production at Serrana, in Araxa - M G."

Jan 1, 1999

By K. Lillkung, J. Kourunen, M. Latva-Kokko

"Carbon-in-leach (CIL) and carbon-in-pulp (CIP) processes utilize activated carbon to adsorb solubilized gold for recovery. Due to carbon attrition and non-ideal carbon management, however, some of the gold is lost in carbon fines and to the solution. The carbon attrition mechanism inside CIL/CIP reactors is mainly abrasion-related. This is critical to gold loss since gold loading takes place predominantly in the outer shell of the carbon particles. Thus fine carbon dust has a relatively high gold content and such a small particle size that it cannot be captured with safety screens. The attrition rate depends on ore and carbon characteristics, but it is always proportional to the mixing power intensity. This rate can be minimized by continuous suspension level measurement and control of agitation speed. In addition, a novel tank bottom structure can significantly reduce the required mixing power input compared to a flat bottom tank. A major challenge in carbon management is infrequent and inaccurate measurement of carbon concentration in the reactors. In order to reduce soluble gold losses by means of improved carbon management, Outotec has been developing a continuous in-situ measurement for carbon concentration that is tolerant to changes in slurry density.INTRODUCTION Cyanide leaching has been utilized since the late 19th century as a standard technology for hydrometallurgical gold production. Since then, gold and silver recovery rates have increased due to technological development, but very similar recovery methods are still being used. The original recovery method was to use zinc precipitation – similar to the Merrill-Crowe process, which is still common for feed materials with low throughput and high silver content. However, in most cases, activated carbon recovery is preferred due to its improved efficiency. The carbon-in-pulp process (CIP) and its modification, carbon-in-leach (CIL), have a lower residual soluble gold level and are not similarly affected by soluble base metals. The main alternative for the use of carbon is ion exchange resins. The principle of resin processes is similar to the CIL/CIP processes, with a different type of adsorbent material. Carbon processes are usually preferred over resin processes due to the significantly higher cost of resin material and the possibility to use simpler, well-established technology with carbon processes."

Jan 1, 2017

By Jamal Asfahani

Abstract - Natural gamma ray well logging, an effective tool in geophysical prospecting, is used to investigate the radioactive and phosphatic layers in the Khneifiss mine in Syria. The interpretation of the gamma ray measurements, using numerical methods of analysis developed previously and applied successfully in some phosphatic areas in Syria, make it possible to define precisely the phosphate thickness from place to place in the study area. This technique has been successfully applied while studying seven boreholes in the area. Sixty-three core samples from phosphatic layers in the boreholes have been analyzed, using gamma ray spectrometry for the determination of P2O5 , U, Th, and K. Good correlation between P2O5 content and U concentration has been found. The total count gamma logs correlate reasonably well with the U core analysis, suggesting that radioactive equilibrium exists in the U decay series. These gamma logs can be therefore used effectively to quantitatively map the distribution of P2O5 and U. The characteristics of both subsurface phosphatic sand and phosphatic rocks have been investigated and outlined using a statistical approach. The affinity of uranium to some trace elements such as V, Sr, Cu, and Ni has been verified using correlation matrices of these elements.

Jan 1, 2002

By S. R. Amos, N. O. Lotter, A. L. Hannaford, J. F. Oliveira, D. W. Broughton

"Ivanplats Ltd appointed Xstrata Process Support to perform the flowsheeting development work for their hypogene and supergene geomet units of the Kamoa Copper deposit, located in the Democratic Republic of the Congo. Through systematic flowsheet development using modern Process Mineralogy, the optimised milestone flowsheet delivered a saleable concentrate grade of 32.8% Cu at 85.4% recovery with hypogene ore, and a saleable concentrate grade of 45.1% Cu at a recovery of 83.4% for supergene ore. The significant value of this development is that a single flowsheet will treat both hypogene and supergene ores and produce saleable concentrates. Further work to advance the flowsheet performance has been identified for investigation in the near future.INTRODUCTIONLocation and Description of the Kamoa DepositThe Kamoa copper resource is located some 40 km west of the city of Kolwezi, in the south west of the Katanga Province of the Democratic Republic of the Congo, in the region of Central Africa. Drilling at Kamoa in 2008-2009 had discovered laterally continuous, sediment-hosted, high-grade stratiform copper mineralisation in a newly discovered copper district that forms a previously unrecognised western extension of the famous Central African Copperbelt – which hosts such world-class deposits as Kolwezi, Tenke-Fungurume, Konkola and Nchanga. This discovery showed that the western end of the Copperbelt in the Congo does not terminate at Kolwezi (Friedland & Broughton, 2009). The resource contains hypogene and supergene geomet units with a transitional zone located inbetween the (upper) supergene and the (lower) hypogene. In the hypogene unit, the major copper sulphides are bornite, chalcopyrite and chalcocite, whilst in the supergene, the sequence is led by chalcocite, then bornite, and finally chalcopyrite. Covellite is present in both units as a minor copper sulphide. Both geomet units will be mined and treated in one concentrator, either as blends or as campaigns."

Jan 1, 2013

By G. Bartolacci

In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in several different types of flotation cells is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through an increase in gas flow rate and/or frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability. Results indicated that flotation conditions could be optimized by monitoring froth stability.

Jan 1, 2007

By R. K. Jonas

Many leading copper and other mineral processors have rapidly adopted advanced controls in last 5-10 years. Almost 600 multivariable predictive controls have been installed in mineral processing, and almost 50% of those are in copper concentrator plants. In most cases, mineral processors rely on 3rd party support to implement these advanced technologies. One challenge facing advanced control user is the selection providers and services for these technologies. The trend has been towards the use of multivariable predictive control and use of technology provider’s services. This paper will discuss status of advanced control, and the merging trends in the mining industry. A review will be presented of how advanced control is being applied in the mining industry over the last decade, and how user challenges are being overcome. Next the emerging uses of multivariable predictive control (such as multi/inter-unit optimization), focusing on the latest trends in concentrator plants. Finally, a review will be made of emerging technology advances in the that can be advantageous to mineral processors. INTRODUCTION Review of advanced control in mineral processing Advanced controls are serving an increasing role to improve processing plant operations and profitability. As advanced control is being installed into more mining processing plants such as copper concentrators, many of these plants are concerned about the selection technologies and vendors to support the installation and maintenance of these controls. In a study by Jonas and Craw (2011), they found that most new users have not had prior experience with advanced controls. It is the author’s experience of almost 30 years in advanced controls that most mineral processers considering advanced controls can benefit from better understanding of the technologies and their support requirements.

Jan 1, 2019

By K. Hanumantha Rao, A. Javadi

Our recent studies revealed that the sulfide minerals in contact with water during grinding produced hydrogen peroxide (H2O2) where the amount of H2O2 production by the minerals found to be in the order of pyrite > chalcopyrite > sphalerite > galena. The H2O2 effect on the oxidation of pulp components and its influence on the concentrate grade and recovery in flotation have been studied and the results have been presented and discussed in this paper. Studies have also been carried out to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp and as well of controlling the formation of these species through known chemical means for depressing the generation of the oxidant. Flotation tests using a complex sulfide ore with the same reagent scheme that is being used at Boliden concentrator in Sweden but with the addition of i) collector and depressant, ii) Na2S reductant and iii) inorganic (EDTA) and organic (TETA) surface modifiers, during grinding stage have been performed to judge the beneficial or detrimental role of H2O2 on the selective flotation of sulfides. The results demonstrate that the selectivity of metal sulfides against pyrite increases with increasing generation of H2O2 in the pulp liquid. H2O2 is also found to be a better oxidant in chalcopyrite-galena flotation separation than the commonly used K2Cr2O7.

Jan 1, 2016

By A. P. Yovanovic, P. Bonadia, M. N. Moraes, C. F. Matos

"The magnesite flotation operation of Magnesita Refractories, in Brumado – Brazil, has four parallel ball mills working in closed circuit with hydrocyclones to grind the ore for the reverse flotation of silicates in mechanical cells. The modification proposed here opens the circuit for three of the ball mills so that their products are collected together to feed a high frequency screen. The oversize of the screen feeds the fourth ball mill in closed circuit for secondary comminution. The product reports to dewatering and flotation. The undersize undergoes desliming and subsequent flotation operation. According to pilot tests performed, the modification on the magnesite flotation operation will promote a 20% increase in the productivity, 8.5% increase in mass recovery and a 26% reduction in water consumption. The gains are due to the fact that the silicates in the feed are concentrated in the smaller particles (<100µm) with over grinding in the existing closed comminution circuit, making it impossible to take advantage of this natural selectivity. The combination of open circuit, more selective milling, and the high frequency screen, ensures high efficiency particle size classification. This renders the process more effective, both to the screen undersize with its high contents of silicates and fines, and to the screen oversize, which is almost without fines and has a higher magnesite grade. This situation allows for the setting of specific parameters for the flotation of both the primary milling undersize and the secondary milling product.INTRODUCTIONMagnesita Refractories, with its operations site in Brumado, is the largest producer of high purity dead burned magnesia (DBM) in Latin America. The magnesite ore is extracted from an open pit mine, named Pomba, after which it is crushed and handpicked. Due to the presence of disseminated silicate the ore has to be ground and concentrated by means of reverse flotation, before feeding the high temperature kilns for sintering and conversion to DBM.The magnesite flotation unit has an impact crusher to reduce the size of the feeding ore, which is transported to the mills by conveyor belts. The milling operation is composed of four ball mills in closed circuit with hydrocyclones. The closed circuit generates a high circulating load with excess fines, which is detrimental to the selectivity of the desliming and flotation operations, reducing both mass andmetallurgical recovery.In the current scenario, the capacity of the flotation plant is insufficient to meet the demand of the DBM kilns, forcing the operation to work with high purity ores in order to attain the highest possible mass recovery in the concentration process. This is not an ideal situation as it requires the mining site to work with higher stripping ratios.The objective of this work was to improve the magnesite flotation unity to increase its productivity. After a detailed analysis, the milling was identified as the limiting process, which made the authors to focus on this operation."

Jan 1, 2016

By Kremena Dedelyanova

The paper presents research of mechanism for the creation of air bubbles in vibratory a column flotation machine. Factors are discussed that influence the increase in the duration of the bubble in the area of contact with the mineral particles. Formulas are derived for the parameter effect of vibrations, applicable to the design of flotation machine. The collision efficiency of the bubbles in a vibratory column flotation machine is determined.

Aug 1, 2013

By Gerhard Melcher, Hermann Hilbrans, Michael Gamroth

"IntroductionSeveral new smelting processes have been proposed and developed during the last 20 years. This has been true, in particular, for copper smelting technology. The important impulses for the advances in this field have been the recent demands regarding the environmental protection, energy saving and improved utilization of the metals contents of deposits, in particular that of complex raw materials.The methods developed more recently for pursuing these objectives have been outlined in several papers. In some of them the advantages and drawbacks of certain developments have been stressed. These documents are of great importance for assessing the different processes. The following paper tries to explain some details of the cyclone smelting process taking into consideration a few of these well-known presentations. The effectiveness of operation of the cyclone smelting process indicates that this process presents a significant achievement when compared with other conventional methods.The application of the CONTOP smelting cyclone range s beyond the field of copper metallurgy or the smelting of sulphide concentrates with the aid of oxygen. The research work carried out in the pilot plant of KHD Humboldt Wedag AG in Cologne-Porz also includes the recovery of the metal contents of intermediate products and processing of smelter residues which have to be converted in a disposable stat e, free of environmental pollution. This paper explains a few examples in this regard."

Jan 1, 1987