Search Documents

By J. F. Davis

Pegmatite dykes containing lithium minerals and beryl occur dose to the borders of intrusive masses of granitic rock in the Winnipeg River area of Manitoba. Both vertical and flat-lying dykes are present. Most of the pegmatites consist of zones, containing characteristic mineral assemblages, arranged more or Jess parallel to the borders of the dykes. Five important lithium minerals are present; each occurs in a separate zone, but all the lithium-bearing zones are situated toward the centres of the pegmatites. Spodumene is the most abundant and widespread of the lithium minerals and occurs as small crystals intimately intergrown with quartz. Beryl is not an important constituent of the lithium pegmatites, but when .present, occurs outside the lithium zones, toward the margins of the -dykes. Beryl is most common in dykes containing few or no lithium minerals. The mineral assemblage in the beryl zone of the lithium dykes is the same as that of the beryl dykes. The attitude and internal structure, particularly zoning, of the pegmatite dykes, and the texture and assemblages of the constituent minerals, have an important bearing on exploration, development, and mining of these pegmatites, and on the extraction of various mineral products from them.

Jan 1, 1958

By P. C. Benedict, J. A. Titcomb

"The following description of the geology of the Northern Empire mine is recorded by the senior author, but is based on the observations and complementary mapping of both authors.The Northern Empire mine is a mile east of Beardmore, and 100 miles northeast of Port Arthur, Thunder Bay district, Ontario.Production started in March, 1934, and terminated in September, 1941. The total number of tons milled was 425,866, from which 153,103 oz. gold was recovered. The lowest level from which ore was mined was the 1,900- foot, but considerable drifting was performed on the 2,075-foot and 800 feet on the 2,415-foot, the deepest level,The vein strikes about N.72°E. and has an average dip of80°S. In stoped sections the quartz averaged about 2 feet wide. On the 1,725-foot level it was drifted on continuously for more than 7,000 feet. In the mine as a whole, practically no commercial ore was found beyond points 1,400 feet west and 1,800 feet east of the shaft. Conspicuous wall-rock alteration extended throughout this section, but not much beyond these limits. There was some splitting of the vein and widening of the alteration halo on the lower levels. The average general colour of the quartz changes with depth .The vein is in 'Keewatin' lava flows, to which it is almost conformable. It lies only a short distance south from the 'Timiskaming-Keewatin' contact ( Fig. 2). This contact is marked by a black graphitic fault. So far as is known the fault is parallel, or nearly parallel, with the flows in strike, but dips at 72°S., which is 5° flatter than the average dip of the overturned flows. A post-vein, almost flat sheet of diabase about 550 feet thick cuts outthe vein from about the 650- to the 1,200-foot level ( Figs . 1 and 3). If it was intruded along a fault, the fault had only minor displacement. A strong alteration halo extends to 200 feet above and below the diabase. The vein was conspicuous but in large part it was below ore grade for 100 feet or more above and below the diabase.-"

Jan 1, 1954

By C. Xiao, F. Mohamm, A. Borsoi

"Nitrogen compounds produced by cyanide destruction and/or blasting are often a cause of concern for environmental compliance and at times, for water re-use in metallurgical circuits. Natural attenuation in tailings ponds and wetlands is not always sufficient to ensure compliance and/or achievement of overall water management objectives. This paper provides a general overview of active treatment methods for nitrogen management followed by an investigation of selective adsorption combined with electro-oxidation as the potential treatment method for thiocyanate. Results from bench scale treatability study are presented. The concept of holistic assessment of nitrogen management at mine sites using Risk Adjusted Life Cycle Cost is introduced and discussed in the context of gold mining operations using sodium cyanide.INTRODUCTION Unlike metals, nitrogen compounds present in mine waters originate entirely from anthropogenic sources rather than mineral deposits. Table 1 summarizes the main sources of nitrogen compounds reporting to mine wastewater.The best management practice related to the use of ANFO involves minimizing contact between ANFO and water, control and monitoring of blasting to reduce the occurrence of misfires, and reducing the consumption of blasting reagents for a given ore body. The most common practice for the management of NaCN is the incorporation of cyanide destruction in the metallurgical flowsheet and the use of tailings impoundments and holding ponds for natural attenuation of cyanide destruction residues such as NH4-N and CNO. At most mine sites there is no active management of NO3-N and SCN in wastewater. While current practices have produced satisfactory results, new enhanced methods to manage nitrogen compounds at mines are needed due to: 1) Increased scrutiny over the adverse effects of nitrogen compounds released into the environment; 2) New effluent standards; and 3) The shift away from wet tailings towards dry stack systems resulting in diminished natural attenuation and dilution of nitrogen residues prior to effluent discharge or water re-use in mineral processing."

Jan 1, 2017

By F. Bosché

Previous research has shown that ?Scan-vs-BIM? systems are powerful to provide valuable information for tracking structural works (progress, quality, safety). However, the transferability of this capability to other construction areas such as MEP works has not been assessed so far. Comparatively, the construction of MEP systems, in particular pipes and ducts, tends to be more flexible with respect to the positioning of individual components, so that Scan-vs-BIM systems could be defeated when tracking MEP installation works. This paper presents recent results on the feasibility and performance of using a Scan-vs- BIM system to track MEP works. The approach followed is presented and then tested with two real-life challenging case studies were conducted simultaneously but totally independently in Canada and Italy. The results show that, as expected, pipes and ducts tend to be more loosely positioned than structural elements leading to a poorer performance of the Scan-vs-BIM system. Nonetheless, it appears that the system works well to assess the level of conformance of site installation works, providing valuable information for estimating emerging performance metrics like ?percent built as-designed?. In addition, the proposed system could also be useful to accelerate and thus reduce the cost of delivering as-built BIM models for in the case of new builds.

Aug 1, 2013

By Y. Shu, A. R. Laplante

"A laboratory Knelson Concentrator (LKC), 7.5 cm in diameter, was used to study the performance of a similar unit at plant scale, 76 cm in diameter, This paper reports on sampling and assaying procedures and problems, and discusses the performance of the plant unit.The sampling procedure was based on the extraction of large samples, 5-15 kg, and their complete processing with a LKC, to characterize size-by-size performance. The procedure yielded reliable estimates of overall gold assays, after blatant assaying errors were corrected. The plant centrifugal unit concentrate was sampled in situ, which yielded very erratic grades, with a large overall negative bias. Due to the very heterogeneous nature of the concentrate, which can be linked to flow patterns in the riffles of the unit, it is recommended that for future testwork, the concentrate be recovered separately, blended and then sampled.The plant centrifugal separator, when operated at a feed rate of 25 t/h, yielded total and free gold recoveries of 41 % and 62%, respectively. This is much lower than previously reported data, and suggest that at 25 t/h, the unit is overloaded. However, recovery did not decrease with time over a loading cycle of 2 hours, which suggests that present loading cycles, generally 1 hour, can be significantly increased. INTRODUCTIONThe study of gold gravity circuits is plagued with the statistical problem of determining the behaviour of particles occurring with a very low frequency. This problem becomes particularly acute with increasing particle size. For example, considering the average weight of a gold flake in the 840-1200 µm (20/28 mesh) to be about 5 mg (Banisi et al, 1991), a reasonably high grade feed of 10 git would require, for a relative error (standard deviation) of 10% on grade, 100 particles, that is 0.5 g of gold, or 50 kg of 840-1200 µm material (a Poisson distribution is assumed). Gy's formula, for the same data, yields a weight of 33 kg, with a shape factor of 0.1 and a size distribution factor of 0.5. Both results are comparable; to obtain the suggested weight of material, a stream containing 5% weight in the 840-1200 µm would require 1 tonne samples (of unsized material). The problem rapidly disappears with decreasing particle size. Still with Banisi et al's data, a gold flake in the 300-420 µm range averages 0.5 mg in weight; the same 10% error on grade corresponds to a weight of 5 kg. Gy's formula for the same size distribution and particle shape factors as above predicts a required mass of 1.4 kg. This would correspond to an unsized sample weight of 10 kg with 14% weight in the 300-420 µm, for example."

Jan 1, 1992

The Red Lake greenstone belt is an irregular mass of lavas sedimentary rocks and intrusives which is approxiately 35 miles long 18 miles wide and 7 miles deep. Basaltic volcamcs are the oldest rocks w1thm the belt. They are believed to have been laid down on an ancient crust which is at least 3 billion (3 x 109) years old and was composed partly of sediments. The basaltic rocks are overlain by acid volcanics and sedimentary rocks which have been complexly folded and are preserved as a down-folded remnant of younger rocks within the older crust. The volcanics and sedimentary rocks of the greenstone belt have been cut by intrusives with a wide range of composition. The emplacement of the intrusives and the accompanying regional metamorph-ism which terminated the orogenic activity in this area are believed to have occurred approximately 2.4 billion years ago. The basalts and many of the basic and ultrabasic intrusives undoubtedly had their source in the sub-crust or mantle. At least some of the granitic intrusives are believed to have had

Jan 1, 1965

By Soumitry J. Ray

Poor visibility of powered industrial vehicles, such as forklifts, used in industry is often the cause of accidents that include pedestrians. Current standards allow up to 20 % non-visible regions for forklifts where measurement of these regions is performed by using lamps. A collaboration of research organizations, including National Institute of Standards and Technology, Georgia Institute of Technology (NIST), and Direct Dimensions, has been evaluating advanced methods for measuring a forklift operator?s visibility. These methods can potentially improve visibility standards. They can also help forklift and sensor manufacturers to determine (1) how visibility-assist sensors and algorithms can be designed and (2) where sensors can be mounted on forklifts. This paper includes explanation of visibility measurement experiments performed and results, associated language suggested to standards organizations, and a prototype design for measuring the visibility of forklifts automatically.

Aug 1, 2013

By Luis A. Tondo

The Paracatu Expansion Project III in Brazil was implemented between 2006 and 2008 to increase the existing capacity from 20 to 61 Million tons per year of gold ore treatment. This expansion led the Brazilian subsidiary of the Canadian Kinross Gold Corporation to become the single largest gold producer in Brazil and the largest single gold concentrator in the world, with a nominal capacity to treat around 167,000 tons per day of ore. This paper describes the Project Development areas for the Paracatu Expansion, using the approach proposed by the Project Management Institute (PMI) and the methodology included in the PMBOK (Project Management Book of Knowledge). The author has more than 20 years of experience in the gold mining industry, having worked as a plant metallurgist, mill superintendent and development manager for RPM until he took the position as the Project Manager of the Paracatu Expansion III in 2005. Luis Tondo has a BSc in Mining Engineering from UFRGS-Brazil, an MScEng from the University of Queensland - Australia and an MBA degree from FDC-Brazil. Luis is currently based in Santiago-Chile, acting as the Project Director for developing projects in Latin America for the Kinross Gold Corporation.

May 1, 2009

By Brian Hart, Stamen S. Dimov

"The naturally occurring carbonaceous material (CM) in gold bearing ores often exhibits strong-preg-robbing properties. It can adversely affect the process of gold recovery during the cyanidation due to its ability to adsorb, or preg-rob gold from the cyanide leach solution.Treatments of carbonaceous ores with chemical surfactants as blinding agents to limit preg-robbing have shown promising results but at the same time have demonstrated that, if not properly used, could have a strong detrimental effect on the gold recovery process. High dosages of surfactants used as passivating agents for carbonaceous matter could lead to unwanted partial passivation of the activated carbon added during the CIL process and severely impact the gold recovery. Optimal dosage for various surfactants would strongly depend on the ore mineralogy and the parameters of the pulp (temperature, pH, surface area and maturity of the carbonaceous material, etc).This paper describes an experimental study on the effectiveness of various commercially available blinding agents used to minimize the preg-robbing capacity of naturally occurring carbonaceous matter. The scope of the study was to: i) establish the optimum addition of blanking agent (surfactant) to minimize the preg-robbing capacity of the CM in the ore, and ii) establish maximum threshold amounts of blanking agents to be used before it negatively impacts the preg-robbing capacity of the activated carbon used in the CIL process. The study procedure involves standardized doping tests to evaluate the maximum preg-robbing capacity of treated CM, coupled with surface analysis with ToF-SIMS to monitor the presence and the degree of loading of these chemical surfactants on both the naturally occurring CM and the added activated carbon.INTRODUCTIONNaturally occurring carbonaceous material (CM) in gold bearing ores often exhibits strong-preg-robbing properties. Thus, it can adversely affect the process of gold recovery during cyanidation due to its ability to adsorb, or preg-rob gold from the cyanide leach solution. The preg-robbing properties of this naturally occurring carbonaceous matter can vary widely between ores, and within a single ore body (Dunne et al.,2013;Helm et al.,2009;Miller et al.,2005). The degree of preg-robbing related to the CM within an ore is defined by several parameters: total organic carbon (TOC) content, surface area, maturity (i.e., crystallinity) of the CM and the presence of various functional groups on the surface of the CM. Preg-robbing gold ores continue to be a significant challenge because of the lack of a single or universal solutions."

Jan 1, 2016

By R. N. Murarka

"Hydrocyclone modelling and selection procedure is illustrated. Computerized procedure for hydrocyclone cut size determination for grinding and non-grinding applications is described.A standard procedure for evaluating operating hydrocyclones is described in detail. Many case studies are illustrated comparing actual plant performance with the computer simulation output in terms of overflow product size distributions.INTRODUCTION Cyclones are widely used for applications such as: close circuit grinding, backfill, tailings and dewatering. Normally, cyclones are used for very fine separations where screens are not suitable or too expensive. Figure 1 shows the separation size range of various classifying devices. Cyclones are popular because of their low capital and operating cost. Cyclone selection procedure for different applications depends on the amount of information available on the cyclone feed slurry characteristics. Closed circuit grinding applications will be discussed in detail in this paper. The Cut Size:The size of the material in the feed which reports 50% to each product stream (i.e. underflow and overflow), after correcting for the feed solids by-passing with the underflow liquid, is termed the cut size or ""d50c"". This is often used as the criterion and the basis for cyclone design.When the corrected recovery to underflow of each mesh size in the feed is plotted against the geometric mean size in microns on a log scale, the micron size corresponding to 50% recovery is the d50c size."

Jan 1, 1992

By R. V. Typliski, G. J. Labarre

"Hudson Bay Mining and Smelting Co., Limited, Flin Flon, Manitoba, Canada, has developed a metallurgical wastewater treatment system employing two-stage lime neutralization, sludge recirculation and conventional mechanical thickening.Laboratory investigations, initiated in 1970, led to the construction of a pilot-scale minewater treatment plant, at Schist Lake Mine, in early 1971. This plant, treating 600 cubic meters/day wastewater containing 30-60 mg/l zinc, demonstrated metal extraction efficiencies of 99% under normal operating conditions.On the basis of this pilot work, a second pilot-scale treatment system was established in 1975 at the Flin Flon metallurgical plant to treat zinc refinery process waste water. Through numerous improvements, including automatic control equipment, the system has evolved to a full-scale operation capable of treating 800 cubic meters/ day wastewater containing 4-11 gm/l zinc. Treated effluent contains 0.2-20 mgll zinc. Hydroxide sludge produced returns to the metallurgical process for recovery of metals while clarified effluent discharges to waste.With the system, Hudson Bay Mining has achieved its original goal: the reduction of environmental contamination, while realizing ii return from metal recovery."

Jan 1, 1980

By Norman R. Paterson

"Under certain conditions useful gravity information of a reconnaissance nature can be obtained with-out measuring elevations by spirit level surveys on the ground. Gravity surveys can become part of a practical exploration program where high cost and slow progress previously hindered their utility. The advantages of the new elevation procedures are realized mainly in remote areas, in areas where ground transportation is slow and difficult and on surveys where the station spacing is large in comparison with the distance of the average optimum level shot. To utilize the advantages, transportation by helicopter or light plane is usually necessary. Methods of obtaining elevation control without leveling include: barometric altimeter survey; photogram-metric -APR spot determinations; methods involving the measurement of gravity gradients. The accuracies of these methods have been tested and compared with the normal accuracy of level surveys. It is felt that each method has its place in reconnaissance gravity work, particularly in the open areas of Northern Canada."

Jan 1, 1960

By Selwyn G. Blaylock

There is no more important problem today than industrial relationship, and probably none that is receiving more thought. But in these days of Epie and Utopia, one has to be rather careful in speaking on this subject. Consequently, for fear that my plea for taking the working man into the family might be misconstrued, by some, as a step towards communism or socialism, I would like to say at the outset that I believe that, so long as we have human individualism, human ambitions, human hopes and fears, straight socialism is as far off as the Millennium. The same applies to communism, which only differs from socialism in that the communist realizes that his ideals can only be attained by massacring millions and destroying all that we hold sacred. Each still looks to Russia for inspiration and guidance, totally disregarding the Soviet swing-back to individual contract work and differential wage scales. They seem to be oblivious of the tyranny and repression in the present Russian system, and get very restless when reminded of it. In spite of the fact that the standard of living in civilized countries has improved tremendously and is still improving, we find that, every seven or eight years, production in many lines has outstripped consumption, and we have had panics or depressions of greater or less magnitude, accompanied by extensive unemployment. It is evident to every thinking person that there must be no little inefficiency in the control of industry. For four long years, governments and industrialists have striven to find the key to solve the present problem. Many countries are getting back to a position approaching normal-Canada probably more so than most. None, however, can feel assured that they have actually cured the situation. All kinds of schemes have been developed; tariff barriers have sprung up over-night where none existed before; currencies have been inflated to gain added security in the home markets and to try to gain advantage in export trade; and each country watches the movements of the others with fear and mistrust. I am not prepared to formulate a full solution of our troubles, but I hope to be able to demonstrate the feasibility and wisdom of the type of industrial relationship I advocate, and also that it may be a large, and possibly an essential, step towards the solution of our difficulties.

Jan 1, 1935

By J. G. Cullain

Inco Limited is an integrated mining, smelting, refining and manufacturing company with operations located worldwide. The Ontario Division operations consist of 13 mines and 10 processing facilities located in Sudbury, Port Colborne and Shebandowan. The scope of our utilization of energy in the Ontario Division in 1976 included in excess of 2.2 billion kilowatt hours of electric power, 12 billion cubic feet of natural gas, 60 million Imperial gallons of residual oil and smaller quantities of other fuels. In addition to the primary energy consumption, waste-heat energy is recovered in various operations throughout the Division, thereby reducing our primary energy requirements. Total expenditures for primary energy alone in 1976 exceeded 60 million dollars. Energy management studies were initiated by Inco's Utilities Department in late 1972, and resulted initially in a program of electric power cost reduction. This program produced significant results by improving the use of the water available for our hydraulic generation facilities and by a comprehensive peak reduction program. Our experience showed that a program of peak power control creates an awareness of both peak and energy costs, and thereby encourages a general reduction in the electric energy consumption as well as lowering the peak demand. Energy management is a continuing program at Inco and, recently, a formal energy management policy and program was instituted. Energy management committees were formed in each plant or mine area to identify the major areas for energy; consumption, thereby isolating areas with large potential energy losses, and determining immediate action which will improve the energy efficiency or reduce the energy waste within their respective areas. A decentralized program with good cross-communication between all committees was felt to be the best method of providing an on-going effective energy management program. In the future, the projections of dwindling fossil-fuel supplies in Canada and the resultant spiralling energy costs will further emphasize the need of sound energy management practices for all Canadian industry.

Jan 1, 1977

"At a current mining rate of 3,750 tons per day, La Mine Doyon is currently the largest gold mine in Canada. La Mine Doyon is an open pit gold mine located in the Abitibi area of Northwestern Quebec. The project is a joint venture between Soquem, a Quebec Crown Corporation in the resource development field and Lac Minerals Ltd., a publicly-held, resource development company. Lac Minerals is the managing company and operator of the project.Doyon went into production in 1980 on a very limited basis at 600 tons/day, and has seen a step wise increase to the current rate of 3,750 tons/day. Initially, all the ore was processed at Noranda Mines, Horne Division as flux for the copper smelter. The East Malartic Mill in Malartic was then upgraded and began processing Doyon ore. The third step in the progressive increase of throughput was the commissioning of the Doyon mill in November of 1982. Doyon ore is currently being processed at all three locations.During 1983, an exploration ramp was driven to explore the ore below the ultimate pit depth. Current plans indicate the sinking of a shaft and the commencement of underground mining during the next 2 or 3 years.Since its humble beginning, La Mine Doyon has always been a success; ore reserves have been extended to the east and the west and will soon be confirmed at depth, the mining and processing rates have been increased 6 fold, and the recovery has been increased from a designed recovery of 85% to over 95%. The intent of this paper is to trace the history and reasons for these rather dramatic improvements."

Jan 1, 1984

By Frank B. Amon

Highland Valley Copper had to make some significant changes in the way it was working in order to counter the effects of ever-increasing costs and decreasing metal prices. A mine/mill optimization plan started in 1997 introduced new technologies and management approaches that resulted in a dramatic drop in cash breakeven costs. The changes involved employee training, added authority and responsibility for staff, better communications, and a consistent approach to setting and achieving property-wide goals. The net effect was to change the culture of the organization from one that was fragmented and focussed on local objectives to one that is cohesive and has common goals. These changes have allowed the mine to remain in business during a protracted period of low metal prices, and have positioned the mine favourably to benefit even more from any future increase in prices.

May 1, 2004

By Larry J. Hulbert, Louis J. Cabri, John L. Campbell, Gilles Laflamme, Chris G. Ryan, Soey H. Sie, Rolando Lastra

"Abstract- The mineralogy of samples from the Wellgreen Cu-Ni-Pt-Pd deposit, Yukon Territory, is complex and the metals of interest are contained within fme-grained minerais which vary in size and mineral associations from sample to sample.The major Ni carriers are pentlandite and violarite; the major Cu carrier is chalcopyrite. About 700Jo of the major Ni carriers and 78% of the major Cu qmier will be liberated at a grind of 80% -'}f,.7 J.Uil (-500 mesh) for typical low-grade gabbro (West zone, sample No. 1). For typical ""clinopyroxenite"" (West zone, sample No. 2) and typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3) the liberation would be 71""lo and 65% for Ni, 74% and 60% for Cu, respectively. Fine grinding, however, cannot liberate the Ni contained in silicates and pyrrhotite, estimated to total24.5% for typicallow-grade gabbro (West zone, sample No. 1), 15% for typical ""clinopyroxenite"" (West zone, sample No. 2), and 12% for typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3).The principal Pt carrier (sperrylite) varies considerably in grain-size between samples and fme grinding, required to liberate the major Ni and Cu carriers, may be counterproductive in samples where sperrylite is relatively coarse-grained, as sorne would then be unrecovered (e.g. sample No. 1). In addition, sperrylite in samples No. 2 and No. 3 is closely associated with magnetite.Palladium occurs in diverse ways. It occurs in the form of several Pd minerais (e.g. sudburyite, testibiopalladite, merenskyite), as a replacement for Ni in several tellurides, antimonides and tel­ lurantimonides (e.g. melonite), or as very low concentrations in pentlandite (up to 34 ppm), chal­ copyrite (up to 9 ppm), and pyrrhotite (up to 5.6 ppm). Palladium minerais and Pd-bearing minerals are strongly associated with chalcopyrite in sample No. 1 and will thus report to a Cu concentrate. However, 22% of the total Pd is in solid solution in pentlandite in this sample and will thus report to the Ni concentrate. In samples No. 2 and No. 3, less Pd occurs in solid solution in pentlandite, and the PGM are distributed mainly among pentlandite, chalcopyrite, and magnetite in sample No. 2, and among pentlandite, pyrrhotite, chalcopyrite, and magnetite in sample No. 3. Therefore, the feasibility of magnetic concentration should be investigated for samples like No. 2 and No. 3, in order to improve Pt and Pd recoveries.Rhodium was found to occur as rare hollingworthite, in sparse cobaltite (up to 2.7%) and, as low concentrations in chalcopyrite (to 10 ppm) and pentlandite (to 12 ppm) by proton microprobe. Iridium occurs in hollingworthite (up to 7.8%) and very rarely as the native metal or in an undefmed Re-Ir-Os-Ru alloy. Ruthenium was determined by proton microprobe analyses to occur in pentlandite (up to 13 ppm) and chalcopyrite (up to 10 ppm), in addition to rare laurite and Re alloy."

Jan 1, 1993

By J. Maheu

Heap leaching is an old technique for the recovery of copper, but a fairly new technique for the recovery of gold.The paper outlines the equipment required for the establishment of heap leaching test facilities and the procedure required to insure meaningful results. Sampling methods, the metal balance, carbon adsorption and stripping and safety procedures are discussed in broad outline.

Jan 1, 1982

By C. M. Campbell

IN 1902, a famous Canadian geologist made the following statement : ?'From what we know row of the iron-ore fields of the Province, we may feel that Ontario is assured of a great future as an iron-ore producing country. Judging from the extent of the territory over which the newly discovered ranges have been found, Ontario should in the not far distant future take her place as one of the chief iron producers in the world". In 1905, an official of the Department of Mines said: "In ten years Canada will have b:ecome a great metallurgical country. You will see an iron industry in this Dominion larger than in any country in the world. Canada will yet furnish the world with its iron supply. It will be the same with iron as with wheat. A decade from now Canada will outstrip all other countries in wheat growing. The production of iron at a cheaper rate than it can be made elsewhere will cause Canada to take a similar position as far as iron is concerned". In 1924, a former President of the Institute, in arguing his claim for inconceivable mineral wealth in this country, stated as a "certainty" that iron-ore deposits on the scale of the ones in Minnesota would be found "again and again" in the Canadian Precambrian. In 1930, a Minister of Mines announced that "The country surrounding Churchill holds large deposits of valuable iron and coal", and he stated that, at that place, 'We will have an industry in iron that will compare with Pittsburgh". These statements are definite promises, just as definite and important as the statement "I promise to pay" on a note, and they are not fulfilled by casually stating, as is the habit, that someday we will work our low-grade iron ores. Nor are they fulfilled by stating, as is often done, "Oh, So-and-So did not mean that ' . Due to their importance and to the prominent positions held by the men who made these statements, they were widely circulated throughout Canada. They were taken at their face value, and on the strength of them and many more of the same kind in regard to our other resources we have planned and built, at huge expense, provinces, governments, civil services, railways, and other equipment. The reserves that were to justify these expenditures have not appeared. There has not been a ton of iron ore mined in Canada for many years, and important commercial reserves are unknown. We have built the mill, but adequate ore is lacking.

Jan 1, 1937

By J. A. Folinsbee, Andre Robitaille, Tony Y. Chong

"Conventional crushing and grinding is followed by gravity concentration to recover free milling gold. Refractory gold, finely disseminated within the pyrite and arsenopyrite matrix, is recovered by flotation followed by pressure oxidation, cyanidation, and cementation. Non-refractory gold is recovered by cyanidation/CIP processing.A comprehensive test program aimed at improving flotation recovery was initiated in June 1995. Plant testing indicated that flotation tails value could be significantly reduced using mechanical flotation cells. Based on these test results, a flotation circuit that incorporates one of the three existing flotation columns followed by mechanical scavenging and cleaning was developed. Detailed engineering was completed in September 1996. Construction started in February 1997 and was completed in 3 months at a cost of $3.2 million. An on-stream X-ray analyzer was installed to provide real-time arsenic and iron analyses and inferred sulphur value on some of the flotation streams.The new flotation circuit proved to be an instant success. Flotation tails values were reduced by 27%. Final tails solids and solution was reduced from 0.035 to 0 023, and 0.0014 to 0.0006 oz/ton Au, respectively. Based on a mill throughput of 1,620 stpd this decrease in tails value will result in an increased gold production of 7,500 ounces per year. The payback for the project is estimated to be around one year.This paper describes the evolution of the project from bench scale testing to commissioning. Also, the operational and economic impacts on down stream processing are highlighted"

Jan 1, 1998