Search Documents

By D. H. Whiting, A. J. Sinclair

"The San Antonio gold mine, in the Archean Rice Lake Greenstone Belt, was in continuous production from 1932 to 1968, during which period the mine yielded 1.35 million ounces (41 985 kg) of gold and 195,000 ounces (6065 kg) of silver from 4.88 million tons (4.44 Mt) of ore for average grades of 0.28 ounces per ton (9.0 g/t) gold and 0.04 ounces per ton (1.3 g/t) silver. After the 1968 closure, several publications appeared implying that gold grade of ore decreased with increasing depth.Recent observations by the authors show that the relatively low grades in the middle levels of the mine are controlled geologically. However, the reduced average are grade in the lower levels of the mine was due to inadequate mining control that led to a high level of dilution. The similarity of geological factors such as vein styles within structural domains, variations in mining control, recent ore muck sampling results and lithogeo chemical profiles all indicate the similarity of ore in both upper and lower levels.Strict mining control should yield improved grades of gold for future production from the lower levels at San Antonio, in contrast with the production grades of the late 19605that represented extensively diluted ore. High-quality production records are an essential component in re-evaluating a past producer, particularly where workings are accessible. Poorly founded conclusions which cannot be checked by access to workings can have a negative impact on the evaluation procedure."

Jan 1, 1990

By H. K. Fredrickson

"Midwest Joint Venture (MJV) owns a high-grade uranium deposit in northern Saskatchewan. The deposit is located too deep below surface to be mined economically by open pit methods, and as a consequence, present plans are that it will be mined by underground methods. High-grade uranium ore of the type at MJV, encased in weak, highly altered ground and with radon-rich water inflows, has not before been mined by underground methods.The test mining phase of the project, completed in 1989, had three objectives: 1. to evaluate radiation protection requirements associated with the handling of large quantities of radon-rich water and mining highgrade uranium ore in an underground environment; 2. to investigate the quantity and quality of water inflows into the mine; and 3. to investigate ground conditions in and around the ore zone as an aid in determining the production mining method to be used.With information gained from the test mining project, a mining method for the production mine has been devised. Level plans have been drawn up, ventilation system designed, pumping arrangements made and methods of ore handling considered. All this is to be done in a manner that will be safe for those doing the work underground. Some of the mining methods planned are felt to be unique in that they are designed to cope with mining problems not known to have been encountered before. New problems underground have required new methods to handle them. Remote drilling, blasting, mucking and backfilling form the basis of the planned mining method."

Jan 1, 1992

By Y. H. Hatzor, D. Bakun Mazor

"A new model for thermally-induced block displacement in discontinuous rock slopes is being explored inside a Controlled Climate Laboratory (CCL). The model is based on a hypothesized wedging mechanism that takes place inside the filled tension crack of a discrete block that rests on an inclined plane. Irreversible block sliding is assumed to develop in response to climatic thermal fluctuations and consequent contraction and expansion of the sliding block material. While an analytical expression for this model is already available, we are exploring the possibility of obtaining such a permanent, thermallyinduced, rock block displacement, under fully controlled conditions in the laboratory, to enable effective analysis of the sensitivity of the mechanism to geometry, mechanical properties, and temperature fluctuations.A large scale (approximately 0.5 m3 in volume) model consisting of four blocks has been installed in the CCL. The CCL permits accurate control of atmospheric temperature (?0.5 °C) from 6 °C to 45 °C. Harmonic temperature function is planned in advance and is controlled by a computer program throughout the experiment process. The minimum length of the temperature cyclic period for thermally-induced block displacement is calculated here based on the existing analytical model.Due to the fact that this experiment is still in progress, preliminary results will be available in the next few months. The obtained results may explain sudden triggering of rock slope failures that are not correlated with common failure triggers such as seismic activities, pore pressure build-up, or freezing and thawing of water inside rock joints."

Jan 1, 2015

By F. Ford, J. Dong

"Laboratory and miniplant testwork was carried out to reject uranium from an Iron Oxide Copper Gold (IOCG) deposit that contains an average of 60-70 ppm uranium with high variability. The dominate copper bearing mineral is chalcopyrite with minor bornite and trace covellite. The main gangue minerals are iron-rich chlorite, quartz and magnetite. The main uranium-containing mineral is uraninite (UO2). Downstream processes require the maximum uranium level of no more than 80 ppm in final copper concentrate.Mineralogical examination reveals that uraninite particles are finely disseminated with grain size of less than a few microns in the deposit requiring fine regrind in order to liberate uraninite from chalcopyrite particles. A lab flowsheet was developed to include ultrafine regrind of the rougher concentrate to the particle size of 80% passing 11-13 µm with up to four stages of recleaning in flotation columns. Finer regrind to 80% passing 5-6 µm may continue to improve liberation but does not decrease uranium level in the final concentrate. In each of the successive recleaning stages by flotation column after fine regrind, uraninite is rejected into the column tailings, with the final copper gold concentrate containing less than 70 ppm uranium from a feed containing 83 ppm uranium. The conceptual flowsheet was further tested in an integrated, continuous miniplant showing average 94% copper recovery with average 74 ppm uranium. The uraninite particles that report to the final concentrate are either locked with chalcopyrite or entrained as liberated particles of less than 5 µm in size."

Jan 1, 2016

By Wang Wenqian, George W. Poling

"Devices and flowsheets for recovering fine placer gold are reviewed. Inefficiencies of gravity processing techniques are documented and discussed. Prospects of combining gravity and froth flotation techniques are presented. Possibilities of using other separation techniques, such as magnetic and electrostatic devices are also discussed.IntroductionSeveral new methods for beneficiating different types of placer ores have been developed in the last two decades. Improved efficiencies in the recovery of fine particles have been achieved by improving gravity flowsheets and machines as well as by developing multiple treatment techniques involving flotation, magnetic and electrostatic separations. Placer gold processing, however, has been an exception to some extent. Gravity concentration using riffled sluices accompanied by mercury amalgamation is still the main method in use today. Because of this, the recoveries of fine gold and the other associated values are often similar to those achieved several decades ago. For example, very few sluice systems recover significant placer gold finer than 100µm in size.Only a few proposals for using alternatives to simple gravity methods for recovering fine placer gold can be found in the published literature. The fixed, low gold price discouraged research in this field for many years. Development of more efficient processes has not kept pace with the recent rapid escalation in the price of gold. Froth flotation for saving fine placer gold might now prove economic, for example. This paper reviews literature published on the recovery of fine placer gold over the period 1907 to 1980. Suggestions for improving the performance in this field, based on the authors' current testwork, are also presented."

Jan 1, 1983

By E. Yan, M. Mankosa, E. B. Wasmund

Mechanical cells are the dominant unit operation in base metal rougher flotation applications worldwide. As economic demand for metals increase, and as the feasible ore grades decrease, the installed capacity of mechanical flotation units worldwide has greatly increased, adding significant capital and operating cost. One opportunity to improve this situation is to use fundamental knowledge to make the industrial flotation process more efficient. A key insight is that the flotation process can be optimized by dividing the processing of the pulp into two distinct fluidic environments; a collection cell where air and pulp mix in a highly energetic compartment, and a low energy gravity separation cell. This is the basis of the “2-stage flotation device” that has been patented by Eriez and marketed under the tradename StackCell™. Two industrial case studies will be presented to highlight the potential metallurgical and commercial advantages of the StackCell. In the first, a train consisting of three pilot scale StackCells (each 0.6 metre diameter) was run in parallel with a train of conventional mechanical cells in a major copper concentrator and benchmarked against a batch Denver test. In the second, the performance of a 3 metre diameter StackCell in a nickel sulfide cleaning application was benchmarked against a batch Denver test. The flotation kinetics observed in the StackCells were 2.4 to 2.9 times faster when compared with the lab Denver test. In the first case study, the kinetics of the StackCell was about six times faster than conventional mechanical cells. It is hypothesized that the efficiency improvement in kinetics is because of reduced “drop-back” during the froth recovery phase, which is reduced because of the reduction in the shear that is present in a conventional mechanical tank cell. This result suggests that a 2-stage flotation system can be used to reduce the working volume of flotation units by five to six times. This would allow operators to significantly reduce the size of their flotation lines for a comparable flotation objective. Some discussion will follow about the scale-up criteria, maintenance and operability issues, comparisons of layout, and possible cost savings. INTRODUCTION The solution that most equipment suppliers have offered to reduce the cost of mechanical flotation equipment over the last 30 years has been to increase the size of the flotation unit cell (Mankosa, 2017). For example, three 100 m3 machines with three smaller motors, mechanisms and control valves could be replaced with a geometrically similar 300 m3 with a larger version of each ancillary component. While there are some efficiencies and cost improvements to be gained by this approach, it does not take advantage of fundamental insights into the flotation process, and it does not represent a step-change in terms of process design or economic benefit for the customer. The advantage of the “bigger is better” approach is that there is past experience of incremental improvements by making cells larger and there is a well-established scale-up method, which allows practitioners to estimate equipment capital costs based on very simple laboratory test- work. A different paradigm, which is gaining interest rapidly is to use a unit operation in which it is easier to optimize the flotation process, which will be described in this paper. This approach is often referred to “2- stage flotation”. Because this approach is new, it is important to benchmark it against existing conventional technology and to demonstrate a robust methodology for sizing equipment and flowsheets. This paper aims to address these issues with two case studies.

Jan 1, 2019

By M. W. Mikhail, R. J. Mikula

"Funding has been made available through the National Energy Program to build a mobile fine coal treatment plant. The plant is intended f or field application and also to upgrade the existing pilot plant facilities.Western Canadian coals with high proportions of fines (due 10 their friability) cause high losses of fine coal to the reject and in turn reduce the over-all recovery of saleable coal. Eastern Canadian coals with high amounts of sulphur of ten require crushing to fin e sizes to liberate pyrite and therefore need effective and efficient separation of these fine sulphur particles. The difficulties involved in solving these problems are two-fold. One is the reluctance to experiment in an operating wash plant and the other is that laboratory scale testing often cannot be extrapolated to the plant environment. The mobile fine cleaning plant with its ability to operate at existing coal preparation plants across Canada and with its flexibility in implementing flowsheet option s and close monitoring of fine coal circuit variables, is ideally suited to solve these fine coal cleaning problems. The mobile plant objectives are to design and optimize flowsheets, evaluate and improve fine cleaning circuit operations and 10 lest new process monitoring and control equipment.The schedule for construction and the required resources will be outlined along with flowsheet options and the general R&D philosophy of the mobile plant.IntroductionIn relation to coal preparation technology, Canadian coal s can be grouped as Eastern coal, Rocky Mountain metallurgical coal and Foothills high volatile bituminous coal. The eastern coals have high sulphur contents and in some cases require crushing or even grinding to liberate the fine pyrite . Rocky Mountain metallurgical coals often occur in highly sheared seams which have been subjected to rapid coalification. The high friability of these coals means that degradation during mining, handling and processing is extensive and results in large amounts of fine s ranging between 20 and 60% by mass of the wash plant feed. The widely varying geo logical structure and exposure to the elements results in partially oxidized coals which perform inconsistently in the traditional method of fine cleaning by flotation . Foothills high volatile bituminous coals for thermal use are frequently interbedded with soft shales and bentonitic clays. These clays disintegrate during washing and swell, producing large volumes of tailings. The presence of clays in plant circuits, particularly fine circuits, tends to increase the viscosity and may cause deterioration of the fines density separation and increase magnetite losses. In view of the fact that fine coal cleaning is the most difficult aspect of coal preparation , a research program is being established to study the factors involved and to offer some solutions.A recent performance evaluation of Canadian washeries showed that yield losses in the minus 2 mm coal circuits were approximately ten times those occurring in the coarse coal circuits(1). Because 2 mm x 0 coal represents 30 to 70 per cent of the raw coal, these losses can be considerable . The operating and capital costs of beneficiating minus 6 mm coal are about four to five times higher than for plus 6 mm coal. In the case o f minus 2 mm coal the costs are even higher. The economic importance of the fine coal cleaning cannot be over emphasized and as a result, the CANMET R&D program is geared for fine coal beneficiation."

Jan 1, 1984

By L. H. Van Loon

INTRODUCTION THE property of Madsen Red Lake Gold Mines, Limited lies between Russet and Faulkenham lakes in Baird and Heyson townships, district of Patricia, Ontario. It is about six miles south west of the town of Red Lake, with which it is connected by an all-weather road. All orebodies found to date at the property are silicified lenticular bodies which lie within tuff beds. The ore bas a specific gravity of 2.95. It consists of mica and chlorite schist, silicified and containing a considerable amount of disseminated carbonate, and mineralized with pyrite, pyrrhotite, magnetite, arsenopyrite, and chalcopyrite. Of these, pyrite, in coarse to fine disseminated grains, is by far the most abundant. Pyrrhotite occurs in ?the gangue material as medium to fine disseminated grains. A very small amount of arsenopyrite, in small crystals, is associated with the pyrite, and small grains of chalcopyrite occur in both gangue and pyrite. Although some of the gold present in the ore is quite coarse, a good deal of it is extremely fine.

Jan 1, 1951

By F. Barriga-Ordonez, J. A. Finch, L. Calzado, S. R. (Ram) Rao

Sludge, formed by lime treatment of acidic drainage and stored in tailing ponds of the Sudbury region, contains 5-7% Ni, mostly in a mix of hydroxides with Fe (~ 10%), Mg (~ 10%) and Cu (-0.5%), and Ca (-3.5%) as sulphate. Investigations were conducted to recover nickel by a 2-stage process. In the first stage, the sludge was leached with sulphuric acid at pH 3.2. About 90% of the nickel was extracted, producing a solution, which contained mainly nickel (2 g/L) and magnesium (3.7 g/L). In the second stage, nickel was separated by treating with ozone which recovered 99% of the nickel in the Ni(III) oxidation state as -85% pure nickel oxide-hydroxide (NiOOH) precipitate. The oxide settled and filtered readily. A potential use of the product in battery making is suggested. The leach residue contained 0.5% Ni making it less toxic for disposal. Some physical properties of nickel oxy-hydroxide and process parameters including ozone consumption will be discussed.

Jan 1, 2005

By M. S. King

"A simple method is proposed for determining the long-term deformation behaviour of evaporites. The theory developed can be tested by measuring the change in diameter as a function of time of a vertical mine shaft opposite evaporite strata. Ultimate shaft closures predicted by the theory agree well with those calculated with the very much more complex theory of Serata (1968), provided that sufficiently high octahedral shear strengths are used in the former.An analysis of measurements made in an isolated opening in a Saskatchewan potash mine shows that the octahedral shear strength of the surrounding potash and halite was approximately 500 psi several years after the opening was mined. This value is less than that deter-mined experimentally for halite by Serata. The same data indicate, furthermore, that the in-situ octahedral shear strength is decreasing slowly with time.The current controversy regarding the actual deformation of evaporites will only be resolved by the cooperation of potash producing companies in releasing data on the long-term deformation of their mine shafts."

Jan 1, 1971

In April, 1961, a large pillar was removed by blasthole mining methods at Inco's Murray mine. More than half a million pounds of explosives were used to break 2,120,000 tons of ore in a single underground blast. The 5, 10 2-inch boreholes, involving 435,815 feet of drilling, were loaded over a three-week period, using conventional explosives and short-period electric caps. From this blast, more than half a million tons of ore have been removed to date (April, 1962) through slusher trenches situated in the footwall of the ore body. T HE Ontario Division of The International Nickel Company of Canada, Limited, operates six underground mines and two open pits in the Sudbury district in the north-central part of the Province. This paper describes the removal of a large pillar at the Murray mine (Figure 1), where 2,120,000 tons of ore were broken in a single underground blast by the blasthole mining method. This is the largest underground blast achieved to date (April, 1962) at Inco mines.

Jan 1, 1963

By N Berkowitz

Slurry pipelining, as now under-stood and practised, can only command marginal interest in Canada, as long-distance railway freight charges in this country are generally lower than slurry pipeline tariffs. Several alternatives to conventional slurry transmission are, however, now emerging, and two such alternatives are briefly discussed with reference to coal pipelining. In one, coal is transported as a suspension in oil; the other contemplates the movement of paste "slugs." Preliminary economic estimates indicate that the resulant process simplification and adoption of common carrier principles could lead to cost reductions that might make Western coal competitive with imported fuel in the power generating stations of eastern Canada. R ECENT appraisals of slurry pipelining techniques, some-what incongruously 'based upon the performance of successful installations (1,2), are making it increasingly apparent that current solids pipelining methods can only command marginal interest as methods of bulk commodity transportation (3). Although some uncertainties remain in matters of detail, it is now generally conceded that long-distance slurry pipelining cannot compete against rationalized railway transportation unless movement of

Jan 1, 1963

By M. S. Badollet, N. W. Edgerton

"A study of the physical properties of long grades of asbestos fibers imported into the United States during the past eight years has disclosed information that will contribute materially to effective selection and use of fibers for electrical products. The study embraced fiber lengths, volume resistivity under three different conditions, total iron by chemical analysis, magnetic rating, conductivity of an aqueous ex-tract and its sodium chloride equivalent.The fibers examined included chrysotiles from Rhodesia, British Columbia, and Barberton area; marlime from Bechuanaland and Province of Quebec; amosite and crocidolites from Africa and Australia; and anthophyllites from Mozambique and from Georgia in the United States. Volume resistivity values provide a relative basis for estimating the electrical performance of end products; magnetic rating -an estimate of the quantity of iron compounds present in excess of those in the asbestos structure; conductivity of an aqueous extract; and an estimate of the ionizable impurities in fibers.Tests of these factors yield in-formation, not heretofore generally known, which may serve as a guide in the evaluation of asbestos fibers for electrical products."

Jan 1, 1960

By Fr. -W. Bach

In the past years the enormous weight saving potential of magnesium sheet has been demonstrated by various research projects all over the world. It has been shown magnesium flat products can benefit automotive, aviation, machine tool and consumer electronics industries. Major material problems such as poor formability, corrosion resistance and high production cost still inhibit the application of magnesium sheets in large scale production. The present contribution outlines achievements in casting and rolling technology. The authors developed an adapted strip casting process in which near-net-shape rolling feedstock of several wrought alloys has been produced. During the rolling process, various parameters were varied in order to modify the microstructure and surface quality of sheet. Several temperature cycles, strains, lubricants, roll surface structures and roll coatings have been analyzed. The sheets were examined and tested in deep-drawing experiments. Suitable rolling schedules have been developed for standard and modified wrought alloys. The study concludes with an overview of current industrial solutions and an estimation of the potential cost savings that might result from the adaptation of the process that has been developed.

Jan 1, 2006

By F W. Irwin

In recent years, a number of significant developments have occurred in the steel industry which are no-table and of general interest. This paper is confined to the steel-melting phase of the business. The development of high production rates on Stelco's Basic Open Hearth furnaces is chronologically summarized. Al-though various aspects of this subject have been presented previously, this paper summarizes the developments in high fuel rates, the usage of basic refractories, low and high oxygen rates and hearth maintenance. Background T HE interest which has been shown in steelmaking techniques in the past few years has been due, primarily, to the extremely high production rates obtained. Upon further study of the facilities and techniques employed to generate this steel at record rates, tonnage oxygen appears as the common factor. It can be stated that tonnage oxy-gen has revolutionized steelmaking techniques to a degree never before encountered. It was only about ten years ago that the use of large amounts of pure oxygen in a steelmaking

Jan 1, 1965

By H. Sano

Most of the dust generated from the copper smelting process in Chile has been stored after the stabilization by hydrometallurgical process because it contains high concentrations of arsenic. However, in recent years, the dust generation has increased because of degrading the quality of concentrate. In addition, the environmental regulations become stricter. On the other hand, valuable metals such as copper and zinc are contained in the dust at high concentrations and it is desirable to recover them. In this study, the effect of dust recirculation to the smelting process was examined in order not only to decrease the amount of dust but also to recover copper. Dust generation and the distribution of arsenic, lead, zinc etc. among the matte, slag and gas phases were evaluated as a function of the amount of recirculated dust, partial pressure of oxygen and temperature. It was found that the direct dust return to the smelting process was quite effective for the recovery of copper and the reduction of dust generation, but the acceptable dust amount was limited by the produced matte quality.

Jan 1, 2007

By J. Xie

In underground coal mining, the potential for an outburst of coal and gas is considered to be one of the major hazards. As such, considerable emphasis is given to understanding and preventing such events. A number of indices are used in the prediction of the outburst in a coal mine. The main indices include initial gas desorption rate, gas pressure, gas content, coal strength, gas flowrate from a borehole drilled in a coal seam, and combinations of the above. Some of these indices are considered to be inadequate, inappropriate or impractical for some coal seam conditions, such as those with soft and friable coal. The Huainan Mining Group (Huainan) in China and the Commonwealth Scientific and Industrial Research Organisation (CSIRO) in Australia have been jointly developing gas content based technologies to predict the risk of the outbursts. One of the major progressive achievements is a new method for determination of outburst gas content threshold values. The method utilizes empirical analyses, numerical modeling, and seam-specific knowledge . This paper describes the method and its application for the #11 Seam at Guqiao mine, Huainan.

Aug 1, 2013

By B. Zeifert, C. Martínez-Morales, A. Romero-Serrano, A. Pineda-Rivera, H. Martínez-Gutiérrez, G. Diaz-Sandi

In this work, the effects of CaO/SiO2 ratio and the FeSO4 and FeS2 contents on the stability of the mineralogical species in chromium-based slags were studied. The chemical stability was evaluated by leaching with an acid solution. The main Cr-compounds in slags with FeSO4 and CaO/SiO2=1 were FeCr2O4 and Ca3Cr2Si3O12, while Cr3S4 predominated in slags with FeS2. The slags with CaO/SiO2=2 mainly contained CaCr2O4. The highest Cr concentration levels in the leaching liquors corresponded to slags with CaO/SiO2= 2, and the lowest Cr concentration corresponded to slags with high FeSO4 or FeS2, owing to the stable binding of chromium in the compounds FeCr2O4, Cr3S4 and FeS•Cr2O3.

Jan 1, 2011

By Paul Girard

"The copper property of Madeleine Mines Ltd. is in Lapotardiere and Boisbuisson townships, Gaspe North. The initial find was made in 1964, and subsequently a copper deposit of 5.3 million tons of ore was outlined. The property lies in Ordovician sedimentary and volcanic rocks near the major granite intrusive of the McGerrigle Range. The host-rock is a 300-foot-thick metamorphosed silty shale unit, close to the contact of the intrusive. The structure itself coµsists of a southerly-dipping monocline or the south limb of an anticline, on which a large dragfold has been imposed.Chalcopyrite, bornite and chalcocite are the principal sulphides present in the ore. Of particular interest is the zoning arrangement of these sulphides. The orebody is chimney-like in shape and appears to be a fracture-filling deposit that is genetically related to the granite intrusive and is confined within a highly fractured zone of very brittle rock. The deposit presents features uncommon to any of the other known copper deposits in the Gaspe Peninsula."

Jan 1, 1969

By H. W. Manley

SULPHUR, like the minerals of coal, iron and petroleum, is one of the essential materials in our modern expanding industrial civilization. Before discussing the salient features of the production of sulphur from the Canadian sour gas, it seems appropriate to outline the historical past and probable future utilization of sulphur. The ancient Greek writer Homer spoke of its "pest-averting sulphur" and the "divine purifying fumigation". Ancient alchemists found sulphur to be a fascinating and baffling material. The discovery of gun powder in the year of 1250, and its application to the art of war a, century later, made sulphur an important commodity in the progress of mankind. The initial manufacture of sulphuric acid in the year of 1736 by the Englishman Joshua Ward, established the basis of a chemical industry that today utilizes 80 per cent of the consumption of elemental sulphur. Commercial production of the chemical soda ash ( N a2C03) discovered in 1787 by the famous Leblanc Process, in-creased international demand for the element sulphur and marks the birthday of the Sicilian sulphur industry.

Jan 1, 1961