Search Documents

By M. Tanaka, Y. Sato, H. Narita, S. Alam, T. Ogata

To ensure a stable supply of rare earth elements (REEs), it is highly necessary to establish the corresponding recycling technologies for RE magnets and phosphors in inplant wastes and endoflife products. Solvent extraction using 2ethylhexylphosphonic acid mono2ethylhexyl ester (EHPNA) is often applied in the separation and purification of REEs. In this study, the equilibrium distribution ratios of neodymium and dysprosium between 1 mol/L nitrate solution and the EHPNA in an alkane diluent were measured at 298K. The experimental data were analyzed by correcting the nonideal behavior of the organic phase using the Alstad empirical equation under the assumption that a complex with a molar ratio of 1:6 (REE:extractant monomer) was formed. The model correlated well with the experimental data and the extraction equilibrium constants were obtained. The extractant equilibrium constants obtained by this methodology would be useful in the design of REE recycling processes using solvent extraction.

Jan 1, 2014

By P. H. Shipway, D. G. McCartney, H. Saghafifar

The microstructural changes during thermal ageing at 650ºC in the interfacial region of Alloy 625 weld overlay on a 2.25Cr-1Mo steel was evaluated. Optical microscopy, scanning electron microscopy in SE and BSE modes, electron probe microanalysis and hardness mapping were used to characterize as-welded microstructure and its changes during thermal ageing and precipitates of interfacial region. Carbon migration across the interface was recognised as a major issue. A region of 300 µm wide adjacent to the fusion line, which was found harder in the as-welded condition decarburized during thermal exposure. Studies revealed that this region transformed to a soft region containing large ferrite grains and micron-sized carbides. In the weld overlay, a 50 µm wide hard band (over 650 Kgf mm-2) adjacent to the fusion line formed and carbide precipitates were observed along grain boundaries. Carbide precipitation mostly occured in the 150 µm wide region close to fusion line.

Jan 1, 2017

By Karl Nienhaus

The BGMR has developed a method for an online-analysis during drilling processes in cooperation with Fraunhofer Institute for Laser Technology in Aachen and various industrial partners. This allows for efficient utilization of deposits, maximum recovery of desired minerals and frequent and costefficient updates of deposit models. The used method, namely laser-induced breakdown spectroscopy (LIBS), was implemented into a compact demonstrator in order to analyze drill dust and loosened material within mining environments and directly on drill rigs. The consequently developed OFURanalyzer (OFUR ? online-analysis of mineral deposits) provides possibilities for exploration and visualization of deposit models in real-time and thus creates an opportunity for innovative applications, such as contactless, continuous quality control of minerals throughout the extraction process. A major challenge in the execution of this project was the necessity to develop a laser system that could withstand rough mining environments dominated by dust, shocks, vibration and therefore would be suited to operate under such conditions.

Oct 1, 2009

By R. Hamilton

"Louvicourt mine began operation in 1994. It is located in northwestern Quebec, 20 km east of Val d’Or. The mine is owned by Aur Resources (30%), which operates the mine, Teck/Cominco (25%) and Novicourt (45%). By the end of 2002 there were approximately 280 employees working on the site, including contractors. Production averages 4300 tons per day, working a massive sulphide body located between 415 m and 920 m underground.Maintenance expenses represent 27% to 29% of the operating costs, and the maintenance personnel represents 34% of the total workforce (including electrical, mechanical and concentrator maintenance staff). Considering these figures, in addition to capital costs and indirect costs, such as energy (electricity, fuel, gas, etc.), it is worthwhile to pay attention to how things are done in order to protect such investment. Every task performed to help understand the impact of Louvicourt’s practices must to be seen as an investment in the reliability of its operation."

Jan 1, 2003

By I. H. Warren

"An analysis of form-coking processes is presented in terms-of their fundamental mode of operation and their relationship to other coking processes. Their possible future role in cokemaking is assessed. IntroductionAny consideration of prospects and possibilities for form coking must commence with the iron and steel industries-their likely future growth pattern on a world and regional basis and the potential direction of future developments in iron and steelmaking technology.From the numerous estimates which have been made of the future consumption of steel, it would appear that a growth rate of 3lllo between now and the year 2000 is likely. Radical changes in steel making technology are unlikely to be commercially adopted on any significant scale during the next twenty years . However, widespread commercialization inter alia of continuous casting and direct reduction, growth of electric furnace steelmaking and a decrease in coke rates will all contribute to a growth rate for metallurgical coke that certainly will be less than that of steel."

Jan 1, 1980

By G. W. R. Kuzyk

"Hydraulic drills, recently implemented at the Tantalum Mining Corporation of Canada, Limited, Bernie Lake Mine, are proving to be an economic alternative to pneumatic drilling systems. The paper describes the application of an electric-hydraulic drill jumbo to the mechanized room-and-pillar mine and its performance. The application of these drills resulted in improved environmental and working conditions.Drill rods and bits are a major cost centre in hard-rock mining applications. The paper also discusses the performance of one manufacturer's product used on the hydraulic drills.IntroductionThe Tantalum Mining Corporation of Canada, Limited (TANCO) started producing tantalum ore from its Bernie Lake pegmatite in 1969. The pegmatite, encased in amphibolite, is shallow seated and flat lying. It is defined by diamond drilling along 4,000 feet of strike and 1,500 feet down dip, ranging in thickness from 60 to 280 feet. Relatively well defined zones of mineralization occur within the pegmatite and form separate orebodies of tantalum, lithium and cesium."

Jan 1, 1981

By G. T. Fisher

A continuous process is used at Phelps Dodge Sierrita Inc. to produce copper sulfate pentahydrate via a solution extraction ? crystallization approach to supply the animal feed market. A review of the fundamental concepts of the process and unit operations is presented. Improvements in the process are aimed at achieving a controlled size distribution of product crystals (-40+80 mesh) with minimization of fines by primary nucleation and crystal breakage. An independent temperature control design was implemented for the heat transfer medium (water) in each crystallizer, albeit using common headers in and out of the chiller. This design was developed to maintain a controlled degree of supersaturation in each vessel while preventing localized spontaneous nucleation of fines and reducing encrustation of the heat transfer surfaces in each crystallizer. A model was developed to calculate the heat load and heat transfer coefficient of each crystallizer along with the saturation copper tenor as a function of temperature and free acid.

Jan 1, 2007

By B. T. Lu, J. L. Luo, J. F. Lu

The present paper investigates the chemo-mechanical effect in slurry-erosion corrosion process of carbon steel to understand the synergistic mechanism due to interaction of chemical and mechanical factors. The erosion-corrosion tests were conducted with A1045 steel in slurries comprising tap water and silica sand. Various heat treatments were adopted to achieve different hardness in the test material. The chemo-mechanical effect is evaluated in line with the correlation between the degradation of hardness in the surface layer and anodic current density. During the erosion-corrosion tests, various anodic currents were applied to find the relation between the anodic dissolution rate and erosion rate. The experimental results indicate that the hardness decreased with increasing anodic dissolution. Based on the fact that pure mechanical erosion rate increased with decreasing hardness, this result suggests that the corrosion-induced degradation of mechanical property is a mechanism of corrosion-enhanced erosion. This theoretical prediction is verified by erosion-corrosion experimental results.

Jan 1, 2004

By R. S. Rogers

Abstract - Forensic geology in a mineral exploration context is concerned with geology and related technical matters as they pertain to legal cases involving exploration and evaluation of mineral properties. Such cases involve the possibility of outright scams that include falsification of data and information, as well as inappropriate application of various technical procedures. Experience in forensic geology in such cases emphasizes the need for systematic quality control procedures during routine exploration/appraisal and indicates the need for more attention to ‘target hardening’ (improving security in the chain of custody of samples and assay results). A number of ‘early warning signs’ that might suggest some form of tampering or falsification of information are listed. These measures will support the work of the "Qualified Persons" (geologists and engineers) entrusted with the scientific and technical aspects of mineral exploration, and facilitate the increased attention to regulatory oversight and enforcement of securities laws recommended in the report "Setting New Standards."

Jan 1, 1998

By Q. Dong, S. A. Nightingale

An investigation has been carried out to assess the effects of an applied voltage on the dissolution rate of MgO refractory in a steelmaking like slag. In this study corrosion results obtained from dip tests using a dense direct bonded MgO refractory in a CaO-SiO2-Fe2O3-FeO-MgO slag are presented. These results demonstrate that the application of a voltage across a dense MgO refractory-slag interface can change the rate of refractory dissolution. For the slag composition used and the voltage range tested, it was found that a maximum corrosion rate was obtained at a voltage setting of -0.45V. The results of this investigation have been explained in terms of voltage affects on Marangoni (interfacial tension induced) stirring and its effect on the MgO dissolution reaction that is at least partly controlled by mass transfer in the slag.

Jan 1, 2004

By M. Kawahara, H. Sunayama

Oxidation rates of the cubic specimens, which were prepared by cutting the shaped magnesia-carbon bricks, were measured continuously with a thermo balance in the temperature range from 1273 to 1 823 K in N2-02 and Ar-02 mixed gas with 2.1 x 104 and 3.7x 102 Pa of oxygen partial pressure respectively. The effect of the graphite content, the maximum grain size of magnesia clinker and the oxygen concentration in the atmospheric gas on the oxidation rate for the MgO-C refractory has been investigated. The value of effective diffusion coefficient of O2, which diffuses through the porous decarburized layer, decreased with the decreasing of the porosity and the oxygen concentration in the external gas phase. It was speculated that the dense layer formed easily due to the high tortuosity of pores and the low recession speed of the carbon interface in the MgO-C bricks.

Jan 1, 2004

By P. Stantke

Glue, thiourea and chloride are the common reagents which are used in copper electrorefining to achieve fine-grained and smooth copper deposition. While thiourea and chloride are clearly defined chemical substances, glue is a natural product consisting of a mixture of amino acids in different constituent parts. The amino acids are continually degraded in the electrolyte by hydrolysis until they finally become completely inactive. This effect is well-known, largely constant and balanced by the continuous dosing of glue. In contrast, the behaviour of glue in the batch container is not always foreseeable. The glue can become partly or completely inactive by contamination with acid or bacteria, for instance. Usually this is not noticed, and partly or fully inactive glue is added to the electrolyte over a longish period, with the result that the copper growth is significantly impaired. Examples from operational practice show that, with the help of the CollaMat system, partly or fully inactive glue batches can be quickly detected.

Jan 1, 2007

By K. Koyama

As a study to establish a new energy-saving copper recycling process, the copper deposition at a cathode and oxidation of copper(I) at an anode from ammoniacal alkaline solutions containing Cu(I) or Cu(II) were investigated in order to examine the feasibility of electrolysis in this solution.. The current efficiencies were greater than 95% in the current density range of 200 to 1000 A m-2. The current efficiency decreased with the increasing Cu(II) concentration and temperature. In the batch-type electrolysis at the anode, during the initial stage, the current efficiencies were 100%, and the anode potentials ranged from 0 to 0.15V vs. SHE at a current density of 100 A m-2. During the subsequent stage, the current efficiency decreased with time, and the anode potential was around 1.35V vs. SHE where oxygen evolution at the anode surface was observed. As a result, the present electrolytic method can be the core technology in the said copper recycling process.

Jan 1, 2007

By G. Dörsam, M. Spreij, S. J. Van der Wal, A. P. Schmidt

The transfer of hot metal desulphurising from the torpedo cars to the hot metal ladles at the IJmuiden BOS plant no.2 caused a decrease in ladle lining life from 680 to 470 heats. Changing the desulphurising agent CaC2 for CaO during a trial period, for environmental reasons, led to a further decrease in refractory life. Availability of the ladles became critical and the major reasons for the low life were identified. Solving one of them, temperature, quickly resulted in restoration of the original lives. However, re- introduction of the new desulphurising agent on 50% of the heats again resulted in a decrease, this time from 700 to 550 heats. In order to be prepared for the full introduction of the new agent, thorough investigation of worn linings was conducted, revealing the major (chemical) wear mechanisms. With these findings, a new design for the hot metal ladle is proposed.

Jan 1, 2004

By D. S. Conochie

The world is poised for rapid growth in consumption as large, less developed economies acquire greater wealth. It might be expected that there would be a corresponding growth in waste generation, but this might not necessarily be the case. The metallurgical industry has an excellent record of process development which has allowed it to provide a high tonnage supply of low cost, high quality metals. Environmental challenges have been faced and indeed the recycling of scrap iron through the electric arc furnace has made a massive contribution to cleaning up obsolete structures and equipment of past generations. Issues in waste generation and processing still remain, and the expectation for cleaner processing and environmental performance continues to rise. The waste impact of key process developments of the last century and the recent developments in metallurgical waste processing in Canada will be outlined. The potential to use state of the art design tools to produce the next generation of zero waste processes will then be explored.

Jan 1, 2004

By D. Harris, S. Murugesan, G. Ye, G. Oprea, J. Rigby, T. Troczynski

The spinel-added and in-situ spinel bonded castables have been developed and widely used in steel industry. It is challenging to develop magnesia-based castables for the non-ferrous industry because the temperatures in industrial furnaces are significantly lower than those in the steel industry and therefore the binding systems of these castables must have the capability to develop a ceramic matrix below 1300°C. It is also challenging to develop a good binding system without addition of fume silica, because the hydration of magnesia may take place during installation, curing and firing of the castables. This work presents the experimental results on developing magnesia-based cement-free, silica fume-free refractory castables using hydratable alumina as the hydraulic binder and a spinel phase as the final ceramic binder. In order to activate the sintering and have a ceramic matrix well developed at the relatively low required temperatures, ultrafine aluminas, chromia, magnesium-aluminate spinel and aluminum titanate powders were used as components of the binding system.

Jan 1, 2004

By Jörgen Appelgren

Atlas Copco, a leading supplier of equipment and services to the mining and construction industries, is consistently pursuing its strategy to offer the most productive and economical solutions by continuously offering new innovative products. These are in most cases developed and tested in close cooperation with demanding end users before being officially launched on the international market. The demands for higher productivity and improved overall economy have resulted in systems for automation of the drilling cycle and also tools for integrating the Drilling equipment to the production control system used by the customer. In terms of improving the blasted material quality, Atlas Copco has placed emphasis on hole straightness and the need for hole logging and positioning. By applying state of the art technology to today?s computerized drilling rigs, major steps in improving overall drilling and blasting performance have been achieved. This paper will give some examples derived from the latest development of solutions for the Rotary drilling product line.

Oct 1, 2009

By Laurence D. Burke

The electrocatalytic behaviour of gold in aqueous media is surprisingly complex and a novel view of gold electrode surfaces is proposed to explain the observed electrochemical responses. The metal surface is considered as a chemically (or redox) modified electrode, with equilibrated, low energy, surface gold atoms functioning as a relatively inert support and low coverage, high energy, protruding gold atoms (or minute clusters of same) functioning as electrocatalytic redox mediators. The protruding atoms are viewed as surface active sites and the complex electrocatalytic behaviour is attributed to the basic instability of the mediators, the diversity (and poor control) of same, and the acid/base (or hydrolysis) behaviour of the oxidized states of the mediators. It is assumed that major advances in the application of gold in the heterogeneous catalysis of gas phase reactions will be accompanied by similar advances in the use of gold in the electrocatalysis area; however, this will require considerable work of both a practical and theoretical nature.

Oct 1, 2003

By J. W. Stickney

"On July 1, 1977 Hudson Bay Mining and Smelting Company Limited announced the commencement of construction of a 3800 ton per day concentrator at Snow Lake, Manitoba. Snow Lake, a community of 2200 people, is located 130 road miles from the main metallurgical plants at Flin Flon.The design, detailed engineering and equipment selection for the project was awarded to Wright Engineers Limited of Vancouver, B.C., who would be working in close liason with Hudson Bay Mining personnel throughout the project.The feasibility of constructing a metallurgical plant in the Snow Lake area, in addition to the concentrator at Flin Flon, had been under study since 1964 with plants of varying capacities and designs being considered. Each successive study recommended a plant of increased capacity and sophistication and finally upon an in-depth study in 1976 of ore reserves, freight rates and operational benefits, the construction of a 3800 ton per day copper-lead-zinc concentrator appeared highly benificial."

Jan 1, 1981

By Kimberly M. Curran

The path by which hydrogen supply is provided to any end use application will have a strong effect on the specific economics and price stability for the product supply and the flexibility with which it can be used. The objective of this paper is to present those variables which play a significant role in the selection of the hydrogen production technology, with a particular focus on several typical mining applications. The variables examined include gas requirements in terms of flow-rate and demand profile, overall volumetric consumption, level of interruption tolerable, gas pressure and quality needs. Also examined are the effects of geography in terms of primary energy supply available as well as existing hydrogen sources, developed or not. The role of these factors in the selection of an appropriate supply chain capable of supporting mining applications that use hydrogen as an energy carrier will be illustrated with a typical mining application scenario drawn upon in the form of a case study.

May 1, 2007