Search Documents

By Kr. N. Karparov

Measurements made with high precision GPS landmarks and geotechnical radar Reutech MSR- 300 associated with the observed movements in the north face of Assarel Mine, where on a horizontal distance of 50 m, 2 groups of landmarks indicated different deformation behavior. Measurements are made in order to confirm the applicability of the radar system in regions of complex geotechnical conditions. The standard deviation of each landmark is used as an accuracy standard between the separate measurements of the deformation vectors made by the high-precision GPS system for each landmark. A very good correlation between the displacement vectors can be seen based on the measurements made with the high-precision GPS system and the measurements made by the radar system MSR-300. Geological, engineering geological and hydro-geological conditions of the area of concern are discussed in this paper. The measured deformations and the FLAC/SLOPE analysis show similar results. In the paper is discussed their local character and their sensitivity to other geotechnical and hydro geological conditions.

Aug 1, 2013

By B P. Scott

Podsol soil horizons developed on Pleistocene glacial sediments overlying the Coronation Mine orebody were analyzed for copper and zinc spectro-photometrically, using biquinoline-isoamyl alcohol and dithizone carbon tetrachloride reagents. Copper and zinc are concentrated in the A. and C horizons, whereas the A1, A2 and B horizons are leached. Of economic significance is the fact that the C horizon contains a copper anomaly, in excess of 100 times back-ground, directly over the orebody. Due to the erratic distribution of high copper concentrations in the Ao horizon with respect to the orebody, that horizon is not considered as a reliable prospecting datum. U NDER certain conditions, metallic ore deposits are accompanied by primary halos of trace elements in unweathered rock surrounding the orebodies or by secondary halos in weathered rock, alluvium, soil, or vegetation above or near the mineralized zones. Where such halos occur, chemical analysis, as applied to the detection of trace elements, is a valuable prospecting aid, permitting the detection of mineralization of possible economic value.

Jan 1, 1965

By H. Link

"The extremely low permeability of the water-carrying beds in the nevonian formation of the potash district of Saskatchewan does not permit the injection of cement or chemicals to seal off sufficient water from the shafts to guarantee the safety of the mine. Based on many years of experience with wet shafts in the German and French potash mining industry, Alwinsal Potash of Canada Ltd. decided to have their potash mine shaft near Lanigan, Sask., which was completed in September of 1967, lined by means of an absolutely watertight lining of combined concrete and steel-plate construction.This shaft lining, consisting of two steel shells of welded construction with concrete filled in between, has proved itself before in the German coal mining industry. It guarantees a permanently dry shaft. With this type of lining, time-robbing and very often abortive injections are superfluous and the regular repair and adjusting work as well as the corrosion of conveyances and ropes can be avoided. Above all, however, the danger of a water inrush into the shaft is abolished completely."

Jan 1, 1971

By M. J. deBastiani

The uranium producing division of Denison Mines Limited operates a 6,000-ton-per-day integrated mining unit in the Algoma area of Ontario. The property is located approximately one and one-half miles from Highway I 08, eight miles north of the town of Elliot Lake. The property was staked in 1953, diamond-drilled in ?late 1954 and 1955, and put into production in 1957. Since that date, the operation has produced $250,000,000 worth of uranium oxide from approximately 11,000,000 tons of ore milled, and paid $18,000,000 in dividends to its shareholders. The operation employs about I000 people, and monthly operating costs are approximately one million dollars. From these figures alone, it is obvious that it was necessary to develop and institute an adequate set ?of controls for effective management at all levels of supervision over a period of four years, a system of production and cost control was developed that enables us to effectively measure the pulse of the various phases of the operation at any given time.

Jan 1, 1963

By R. M. Porter

PILLAR extraction at the Sullivan Mine bas been in progress for over twenty-five years and bas .involved progressively larger pillars. The largest pillar blasted to date exceeds one million tons and is described in this paper. This blast is believed to be one of the largest to take place entirely under-ground. The Sullivan Mine, owned by The Consolidated Mining and Smelting Company of Canada Limited, is located in the southeastern corner of British Columbia on the east flank of the Purcell range overlooking the twenty-mile wide Rocky Mountain Trench (Figure 1). The orebody is a bedded replacement deposit in argillites, varying in thickness up to 300 feet, but averaging about 80 feet. Above the 3900 Level, the dip varies from nearly horizontal to 40 degrees; be-low the 3900 Level it varies from 45 to 20 degrees (Figure 2). Pillar extraction follows a plan of retreating outward from caved areas. The size of each blast is determined by the effect which the removal of support

Jan 1, 1961

By R. W. Thompkins

MINE operators are concerned with temperature conditions in their mines, particularly the effects of high temperatures on the l1ealth and efficiency of tl1eir employees. This paper is written to focus attention on the variables of heat transfer between rock and air. It illustrates the difficulties of predicting the manner, and the extent, of heat transfer from theoretical concepts, prior to actual operation of a mine airway. There are ~1any sources of heat in mines. The most important is that of the rock surrounding the airway. This heat, in turn, is a product of the age of the rock, faulting, proximity to recent igneous activity, oxidation of sulphides, hot ground waters, etc. The sources of heat may be constant for any one mine, but they are far from constant when dealing with various mining districts or e1•en with a number of mines in the same district. A second source of heat is that produced by machinery in operation. Practically all the waste

Jan 1, 1962

By T Salman

The construction and use of the B.E.T. (gas adsorption) apparatus is described. Examples are given for the determination of large and small surface areas using nitrogen and krypton. Introduction A NY study of the milling of ores from crushing to grinding, classification, and concentration and finally dewatering of the products involves solid particles which are either in contact with a gas or a liquid phase. The surface area of the solid and its characteristics constitute important parameters in all mineral dressing operations. The success of any particular operation is dependent on the interaction of the surface of the solid particles with the gas or the liquid phase. Particle size and specific surface (surface area per unit weight) continue to be important parameters in the flotation research associated with the adsorption of collector molecules or ions on mineral particles, as in the early years of mineral dressing research (1). In order to understand the mechanism of the flotation process, it is essential that the surface properties of the adsorbent be known.

Jan 1, 1965

By P. Leo

The hot deformation behavior of a Mg-9A1-1Zn alloy produced by high pressure die casting has been investigated by means of compression tests in the temperature and strain rate ranges of 125-300°C and 10-5-10-1 s-1 and torsion tests over 150-450°C and 5, 0.5, 0.05 5-1 . The compression samples were deformed in the die-cast state or after homogenization at 415°C for 2 h to evaluate improvements. A premature fracture at 45° with respect to the compression axis was observed in samples strained at low temperatures and high strain rates. The torsion specimens were tested as received or after a predeformation-homogenization treatment. In addition to constitutive analyses suitable for modeling previously published, the results are fitted to a relationship between strain rate normalized by diffusion coefficient and flow stress normalized by modulus. The results fit well with a set of published creep experiments that were conducted in the range of 70-150°C.

Jan 1, 2006

By Dallas W. Davis

Twin - Kennecott Deal Announced April 15, 2004 ! Kennecott earns 56% interest, if in 4 years, spends C$10 million and recovers at least 200 cts of +1 mm diamonds in all dimensions from any contiguous body ! Earn-in can take up to 6 years, but incurs stepped reduction of interest from 56% to 46% or 0% if $C10 and 200 carats not achieved ! By funding all costs through feasibility study, Kennecott earns 71% in 7 years, or, stepped reduction to 62% if completed after 8 years ! By achieving production within 10 years and funding Twin?s share of development and construction costs, Kennecott earns further 4% ! If no election to develop a mine within 2 years of feasibility study completion, Twin may present development proposal which Kennecott has 60 days to elect to follow or transfer management to Twin and dilute to 49% ! Each party has one time right to elect to market its diamond share ! On signing and annually, Kennecott will purchase $C250,000 of Twin shares at 130% of then prevailing market price until achieved earn-in

May 1, 2004

By R. Patrick

As a unique South African organisation, CSIR: Division of Mining Technology (Miningtek) strives to support the mining industry by improving health, safety and productivity through developing, adapting and transferring technology. Considerable effort is currently directed towards the development of potential non-explosive mining methods with the potential to allow continuous mining in narrow reef conditions. Besides improving productivity, continuous mining results in concentrated mining which has a significant impact on reducing infrastructural costs. Impact Ripping and Water Pulse Rock Breaking have been tried on gold mines, whereas Activation, Mini-Disc? cutting and the Plasma Holemaker are currently being tested on platinum mines. The organisation?s many years of experience in novel rockbreaking, together with its world-wide collaborator network, has placed it in a unique position to assist the mining industry and manufacturers in developing and/or adapting existing technologies for application underground. Currently a range of technologies are being investigated, which have reached different stages of maturity. The main technologies under investigation are; - Impact ripper system - Water pulse rock breaking - Activated undercutting rollers - Mini disc cutters - Electric rock breaking

Oct 1, 2001

By L. Li

The rock quality designation (RQD) was initially introduced by Deere (1963) for civil engineering. But, its application has been largely extended to rock mechanics and has become a fundamental parameter in geotechnical engineering (e.g., Hoek & Brown 1980; Milne et al. 1998). The success of this definition is due, in great part, to its simplicity. However, this index includes a number of limitations. Among these limitations, a critical one is associated with the arbitrarily selected threshold value (e.g., Priest & Hudson 1976). Consequently, the RQD value would vary with different threshold length for the same core. Also, using the customarily and universally adopted but very arbitrarily selected threshold value of 10 cm (for NX cores) in the assessment of RQD, the RQD values usually tend to be either high or low in most rock engineering. Some intermediate values (50%) are less frequently encountered (Harrison 1999). The original definition of RQD does not well represent the actual quality of rock masses. In this paper, an improved definition of rock quality designation (RQDc) is given.

May 1, 2009

By Andrea M. Ouchi

A major focus of ground control research presently being conducted by the Geomechanics Group in the University of British Columbia Mining Engineering Department is to incorporate weak rock masses (RMR76 less than 50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented by mapping of one mine in Montana and of several mines within the Carlin and Getchell Trends of Nevada. In addition, a neural network analysis has been performed and modifications of the span design curves at the lower RMR76 range have been made. The common factor in all the above mentioned mines is a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be dealt with to safely extract the mineral bearing rock. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

May 1, 2004

By T. Gerritsen, R. MacRosty, R. Pula

For several years Hatch has been installing fibre optic temperature sensors on the copper cooling elements of smelting furnaces to improve monitoring capabilities in critical locations. The metal/matte tapblock is a key area to monitor in the furnace as it undergoes severe wear from the molten material repeatedly drained through it. The high wear rate around the tapblock means downtime is necessary to perform refractory repairs. A good understanding of the tapblock condition allows the operation to maximize safety and production; consequently the metal/matte tapblocks have been the focus of this study. Fibre optic technology allows the installation of numerous sensors in locations that are very sensitive to refractory thickness, thereby providing information previously unavailable with traditional measurements. The transient nature of the thermal response to tapping and the three-dimensional geometry of the tapblock confound the interpretation of refractory thickness from temperature measurements. This paper focuses on the analysis of both plant data and thermal modelling simulations and details the progress made in relating the temperature measurements to the refractory thickness in front of the copper tapblock.

Jan 1, 2014

By K. Morikawa, K. Asano, J. Yoshitomi

The quality requirements for ladle shrouds have become stricter year by year to the pursuit of higher productivity and improved quality in the continuous casting of steel. The ladle shrouds must be sufficiently durable under severe conditions, such as operation without preheating and during several sequential castings. The consideration is that ceramic fibres, which have been applied in shrouds for thermal insulation during casting, could pose a risk to the worker's health. We realized materials for the ladle shrouds which show high strength and low elasticity. At the same time pursuing effective insulation, a coating which contains no fibres (Foaming Coat) has been developed, replacing the conventional one containing fibres. These materials are durable under conditions of repetitive use and consequently satisfy the customer's demands. The ladle shrouds which were improved in this way have achieved an excellent durable life in hot service of three times that of conventional ones. This paper reports the recent technological developments in ladle shrouds as well as their performance under hot operating conditions.

Jan 1, 2004

By Douglas E. Wolfe, Jogender Singh, Robert Miller, Dong-Ming Zhu, Jeff Eldridge

This paper discusses microstructural changes produced by two novel approaches using electron beam physical vapor deposition (EB-PVD) in which periodic strain fields/microporosity was incorporated within the large columnar grains of Zr02- 8wt.%Y2O3 (8YSZ). The traditional columnar microstructure of partially stabilized zirconia has been slightly modified to produce a lower thermal conductive thermal barrier coating (TBC) by periodically interrupting the condensing vapor resulting in microstructural modifications with diffuse or sharp interfaces and morphological changes on the sub-micron scale without changing the composition of the TBC. These microstructural modifications resulted in a 20-30% reduction in the thermal conductivity, 28-56% increase in hemispherical reflectance, improved oxidation cyclic life (over 100%), and better strain tolerance as compared to standard ZrO2-8wt.%Y2O3 deposited on platinum-nickel-aluminide and CoNiCrA1Y bond-coated MAR-M-247 test samples. The TBC with tailored microstructures were examined by various techniques including scanning electron microscopy (SEM), x-ray diffraction (XRD), steady-state laser heat flux technique, and hemispherical reflectance.

Jan 1, 2004

By T. Cutard, E. Yeugo Fogaing, C. Gault, H. Marzagui, N. Prompt, M. Huger, C. Deteuf

This paper deals with studies made in the field of the French research network PROMETHEREF. Several refractory castables are considered in this program. In the present paper, one of these materials is considered, it is a low cement castable based on andalusite aggregates. A particular attention is paid to microstructural changes during the first heating and on their effects on the high temperature mechanical behavior. Microstructural evolutions have been characterized by the way of dilatometry, scanning electron microcopy and X-ray diffraction. In-situ observations by environmental scanning electron microscopy gave complementary results on these high temperature microstructural changes. They deal with microcrack formation, phase changes, crystallization, liquid phase formation and sintering. By propagation of ultrasonic waves, high temperature continuous measurements of the Young's modulus have been made. Results confirm the existence of microstructural changes and allow to quantify the Young's modulus variations all along specific thermal cycles. High temperature four point bending tests and room temperature tensile tests were made in the same temperature range. Behavior evolutions could be found and interpreted with the help of previously mentioned results.

Jan 1, 2004

By G. M. Ross, I. M. Ross, J. A. Scott

"The otherwise waste heat in many water streams in the mining industry can be used to provide space heating of adjacent infrastructure including laboratories, workshops, and offices. This can be achieved by using heat pump systems, which can work as a replacement or in conjunction with existing space heating. In the example investigated—process cooling streams at an ore smelter—the analysis provided illustrates that annual heating costs can be 19% lower and a simultaneous 62% reduction in CO2 emissions can be achieved.RÉSUMÉ Dans l’industrie minière, la chaleur qui serait normalement perdue des circuits d’eau pourrait servir à chauffer des structures adjacentes incluant les laboratoires, les ateliers et les bureaux. Cela pourrait se faire en utilisant des systèmes de thermopompes, qui pourraient remplacer ou s’ajouter au chauffage existant. Dans l’exemple étudié, des circuits de refroidissement de procédé à une fonderie, l’analyse fournie illustre qu’il est possible de réduire les coûts annuels de chauffage de 19 % et d’obtenir une réduction simultanée de 62 % des émissions de CO2."

Jan 1, 2016

By K. D. A. Whaley

The Captain North Extension deposit consists of five sulfide lenses hosted in cherty and chloritic metasediment that is bounded by quartz-eye rhyolite and laminated rhyolite. Lens 2 consists of sphalerite and galena with silver-rich tetrahedrite in chert. Lens 3 contains massive pyrite, with chalcopyrite and minor gold, gradational to minor pyrite in a chloritic metasediment. The other lenses are unexplored. The sulfides occur as beds, fracture infills, and disseminated grains. Reserves are estimated at 207 555 tonnes grading 7.380/0 Zn, 2.76% Pb, and 91.81 g/t Ag. The deposit is isoclinally folded, dips steeply west, plunges 50 degrees south, and is faulted out to the north, where drag folding has reversed the plunge. Minor cross-faults contain talc and sericite. High sphalerite but low pyrite abundances result in poor responses to standard electromagnetic techniques. Lens 3, which contains more pyrite than Lens 2, responds better to induced polarization and allows detection. Geochemical anomalies are found in a nearby swamp and stream, but an impervious till cover inhibits the development of soil anomalies.

Jan 1, 1992

By P. R. A. Andrews

"The sillimanite group minerals, kyanite, sillimanite and andalusite are identified as alumino-silicate minerals with the common chemical composition AIP3.Si02' so that each possesses similar physical properties. Kyanite is the most abundant mineral and mainly occurs in Quebec, Ontario and British Columbia; sillimanite occurs in Ontario and Manitoba; and andalusite in Nova Scotia. The main use for the sillimanite-group minerals is in refractory applications for the production of refractory bricks and shapes. In refractory applications, the main performance criterion is the relative percentage of mullite formed within the material during firing. This phase gives a greater degree of resistance to creep deformation and slag attack, and improves the ability of the refractory to withstand high temperatures under load. The beneficiation of refractory silicate minerals has been the subject of many investigations at CANMET, and the former Mines Branch. Eighteen kyanite, two sillimanite, and three andalusite evaluation studies were conducted between 1933 and 1987. A review of some of the more important studies is presented, which includes information concerning mineralogy, beneficiation methods and flotation data."

Jan 1, 1995

By Juan C. Sotomayor Álvarez

The Huantajalla mine is seated on Uchucchacua 's Mixing District that is the fourth producer of Silver in the world. Huantajalla Mine is a new mine that nowadays is being explored and recently it has began to operate. The project for 4-A vein exploitation in Huantajalla Mine using Longhole drillings as a new method of mixing is developed by Planning Department of Uchucchacua Mine in coordination with Geology Department of this mine, started in June 2004. This project is funded by Company of Mines Buenaventura S.A.A In July 2002, Geology Department started the exploration on the area of Huantajalla Mine, discovering the 4-A vein. The reconnaissance and definition of the vein finished June 2003, finding 79,080 Ton of mineral of Silver with a grade of 40.0 Oz Ag/ton and a thickness of 1.85 meters (6 feet ). Using the longhole method on the vein exploitation will replace the cut and fill and shrinkage methods, and it will keep a dilution of 15%.

Oct 1, 2004