Search Documents

By G. M. Ritcey, V. M. McNamara

"In the processing of gold ores by the cyanidation route, effluents which are discharged to the tailings areas can contain up to several hundred parts per million of cyanide in complex combination with similar quantities of heavy metals. Complicating this obvious problem of waste control are concentrations of thiosalts and thiocyanates which are roughly equivalent to the amounts of cyanide species. Although most gold mills are located in thinly populated areas, such contaminants can represent a potential environmental problem due to the various limitations exhibited by on-property ponding.The former Extraction Metallurgy Division of CANMET recognized the problem and, in early 1974, invited representatives of the gold mills to Ottawa to discuss the situation. At that meeting members of the Division presented a ""state of the art"" literature survey of cyanide abatement technology for waste solutions, together with preliminary cost estimate data(1). Shortly thereafter, Environment Canada, together with Environment Ontario, decided upon a guideline of 0.1 ppm (0.1 mg/l) total cyanide content as tolerable for an effluent stream which is discharged, in any manner, to the watershed."

Jan 1, 1978

By Bennett McLaughlin, Gille Brousseau, John F. Cook

"La Mine Bousquet commenced operations in October 1979. Mining has been by underground methods from two main zones which dip steeply to the south , Sub-level stoping methods with following fill are used.The orebody and immediate country rocks are sericitic and highly schistose. The intensity of schistosity varies significantly and poor ground conditions prevail, especially within the orebody,Initially few mining problems were encountered but in May 1981, significant damage occurred. A system of stabilizing pillars was introduced with improved support systems. Predevelopment in ore and pre-drilling of blastholes were reduced with extra footwall development.Damage has continued to occur on a regular basis particularly during the spring thaw. Generally, the adverse conditions have been successfully overcome.IntroductionMost of the mining problems that have been experienced at Bousquet have been caused by poor ground conditions . This pa per describes these conditions, considers the cause and describes the ways in which the conditions have been dealt with . Despite the problems, Bousquet is a successful operation which in 1983 produced 95,000 ozs of gold from 514,000 tons of ore."

Jan 1, 1985

By D. A. Mackie, J. E. Rider

"Good belt conveyor design is the most often neglected detail in the engineering of a plant. This results in downtime from spills or jams and premature failure of equipment components. Careful layout and component selection will result in better operation, a cleaner plant and therefore lower maintenance costs.IntroductionDespite the availability of many excellent sources of data on conveyor design, such as the Conveyor Equipment Manufacturers' Association (CEMA) Manual, ""Belt Convyors for Bulk Materials"" , there continues to be repetitive errors made in design. Why? Certainly, there is no substitute for experience, but largely, classical errors in belt conveyor design is rather elementary and so the temptation to have the work done by relatively inexperienced designers is great. What that does is develop "" experienced"" designers who become incompetent through no fault of their own. It is hoped that this paper will supplement available design data, help those who are "" put into"" a design situation to better cope with their predicament, and ease the lives of plant maintenance personnel."

Jan 1, 1990

By W. F. Giuvlore, E. Mcroberts, T. S. Golosinski

"The rising demand for Canadian coal and depletion of shallow deposits, most suitable for surface mining, result in rapidly increasing volume of waste materials which have to be moved by the coal mining industry. While at present this challenge is being successfully met using conventional mining methods, in the future, innovative methods must be considered if Canadian coal is to remain competitive.The need for more efficient mining methods is also faced by the oil sands industry to assure competitiveness of the synthetic oil price.A look at the world mining practice indicates that large volumes of material can be economically mined and moved by the continuous mining systems comprising bucket-wheel excavators, belt conveyors and stackers. To assess the state of art and applicability of this mining method to Canadian conditions, the field trip was organized by the Department of Mining Engineering o f the University of Alberta, to several typical mining operations in Europe. It is in Europe where the continuous mining methods were developed and are almost exclusively used in large-scale surface mining."

Jan 1, 1984

By Holly L. O. Huyck

Disseminated hypogene sulphide mineralization in the Lakeshore porphyry copper deposit (also called the Cyprus-Casa Grande deposit) of Arizona occurs in both a granodiorite stock and associated volcanic rocks. Structural development and vein paragenesis at Lakeshore are similar to other Laramide porphyry copper deposits of the southwestern U.S. Two major structural trends are present: intrusive contacts, copper-bearing potassic alteration veins and major post-mineralization Basin-and-Range type faults trend N-NW, whereas phyllic veins and secondary post-mineralization faults trend N-NE, and deep propylitic veins trend NE-ENE. Lithologic permeabilities, caused by fracturing in all rocks and by grain size distributions in volcanic rocks, controlled the distribution of copper mineralization. Differences in chemical compositions of host rocks did not affect are grade. Structural control, through density of chalcopyrite-rich veins, was the major control of are grade. Fracture density of other potassic vein types did not strongly affect grade. Within volcanic lithologies, permeability, as indicated by grain size distribution, provided a second-order, but significant, control of mineralization.

Jan 1, 1990

By Robert B. Parsons

"Finance Minister Paul Martin's second budget might be good for Canada's mining industry in the long run, but the budget raises a number of concerns for the industry in the near term. The budget papers suggest that the 25% resource allowance is not working as intended, and report that the Department of Finance will be reviewing this valuable allowance. The so-called ""large corporations tax"" rate will be increased. This annual tax, which is imposed on a corporation's capital even when the corporation is not in production, is particularly harmful to the mining sector.IntroductionThe Honourable Paul Martin, in his second federal budget, emphasized spending cuts and made only modest tax changes. However, two of these tax changes could have a serious impact on the Canadian mining industry: the proposed review of the 25% resource allowance; and, the increase in the large corporations tax rate.Personal Tax Measures Personal Tax Rates UnchangedThe government has been under political pressure not to increase personal tax rates. Mr. Martin's announcement that rates would not change will be popular."

Jan 1, 1995

By L. R. Hougen

The Falconbridge Matte Leach Process yields high-purity nickel chloride by selectively dissolving nickel from copper-nickel converter matte with hydrochloric acid , purifying the solution by solvent extraction and crystallizing NiCl2 4H2O by further acidifying the purified leach liquor. In the Kristiansand Matte Leach Plant, a granular oxide is produced by high-temperature hydrolysis of the nickel chloride for subsequent reduction to a high-purity granular metal product, designated NICKEL 98. This paper describes the investigation of on alternate route to processing nickel chloride in which high-quality cathode nickel is produced by electrowinning from all- chloride electrolyte. The investigation was made in a pilot circuit containing two production-size electrowinning tanks operated in conjunction with the commercial-scale leach plant.

Jan 1, 1977

By D. Berkley

Off-gas systems often become the limiting factor in production increase and environmental projects. Any upgrade or new off-gas project needs to address control instability issues, instabilities that can result in safety hazards, significant loss of system capacity and/or emissions to the environment [1]. In addition, the design engineer must optimize system configuration and equipment size for the new operating conditions, to have a technically feasible and economically viable project. Dynamic simulations can be used for addressing both the control stability and the design optimization issues. This paper illustrates how the dynamic simulation of transient processes and of their control system can be used in "real life" situations for these purposes, presenting the example of an electric furnace off-gas system design.

Jan 1, 2005

By G. A. Gross

"Nearly 90 per cent of the iron ore produced in Canada is derived from iron-formation or bedded iron deposits. About 70 per cent of this consists of concentrates obtained from iron-formation; another 20 per cent was formed by natural enrichment processes.Four principal varieties of iron-formation are recognized -the Algoma, Superior, Clinton and Minette types. Differences in their geology, mineralogy, chemical com-position and environment of deposition are of special significance in their evaluation as ore.The properties of the ores, including grade, beneficiation qualities and minor element content in taconites, metataconites and naturally enriched ores, reflect characteristics of the primary stratigraphie units from which they are derived. A detailed description of the stratigraphie facies is essential for efficient utilization of these source beds."

Jan 1, 1966

By G. E. Veins

A three-phase, continuously-operated, 250 kv.a. electric smelting furnace has been installed at the Mines Branch, Department of Mines and Technical Surveys, Ottawa, for the experimental treatment of ores and by-products of interest to the Canadian mining, metallurgical, and chemical industries. In the operation of this furnace particular emphasis is placed on the accumulation of quantitative data which will be useful in determining the most suitable smelting technique and the nature of the products, and in arriving at preliminary conclusions regarding the cast of power and electrodes. The results obtained in the experimental smelting of iron, manganese-iron, titanium- iron, nickel, and chromiumiron ores, and of a number of industrial by-products, clearly show the value of such treatment for materials of this type.

Jan 1, 1957

By M. I. Kalashnikova, Y. M. Shneerson, E. E. Zhmarin, Y. V. Degtiarev, E. M. Vigdorchik

Separation of a magnetic fraction from nickel concentrate following matte flotation, and its treatment in a separate circuit enable reduces precious metals losses. The magnetic fraction is treated in two stages of oxidative leaching: atmospheric and pressure leaching. A study of the atmospheric stage, using mathematical modelling, is described in this paper. The mathematical model and experimental data were used to carry out industrial process calculations. The model enabled extrapolation of the results of batch laboratory test to industrial-scale continuous processing and the selection of optimal process conditions and large-scale equipment. In December 2004, commercial oxidative leaching tests were performed on the magnetic fraction at the Severonickel Plant (Monchegorsk, Russia). A comparative analysis of the mathematical modelling results and the actual process parameters is presented.

Jan 1, 2005

By Edward Martinez

Due to its unique properties, chrysotile asbestos is used in many diversified applications. In recent years, a better understanding of the structure and properties of chrysotile has evolved due to the research efforts of many investigators. A summary of the results of some of these investigations is given. An attempt is made to show the relationships between the properties of chrysotile and its crystal structure. Examples taken from the literature are cited in which methods have been developed for modifying the properties to improve the performance of asbestos in some applications. These include the effect of pH on the positive zeta potential and the addition of sodium silicate to improve filtration characteristics. The dehydroxylation and formation of forsterite when chrysotile is heated are also discussed.

Jan 1, 1966

By E. Mohammadi Zahrani

In this study, Mg-doped fluorapatite (Mg-FA) nanopowders were prepared through a sol-gel, technique and characterized. Designated degree of Mg2+ ions incorporation into the apatite structure was indicated by the x value in the general formula of (Ca10-xMgx (PO4)6F2), where x=0, 0.25, 0.5, 0.75, and 1. XRD, AAS, FTIR and TEM techniques were utilized to characterize the synthesized nanopowders. In vitro bioactivity of the powders was evaluated in simulated body fluid. Powders had a crystallite size less than 100 nm. It was concluded that Mg-substitution could alter bioactivity and dissolution behaviour of Mg-FA. These two parameters were proportional to magnesium content of the powders.

Jan 1, 2010

By Corinne Boone

CO2e.com, LLC - launched in November 2000 - aims to be ?the global hub for carbon commerce.? CO2e.com is a subsidiary of the Cantor Fitzgerald Group, one of the world?s leading brokerage firms Recent Investor in CO2e ? Mitsui & Co. Alliance with Cantor Fitzgerald Environmental Brokerage Services Group (CFEBS) Offices in London, Toronto, Tokyo, New York, San Francisco, Los Angeles, Connecticut, Houston Primary Goals/Benefits of ET § Goals of Emissions Trading: ? Permit Industrial Growth/Expansion ? Promote Economic Efficiency and Flexibility in Meeting Air Pollution Standards § Benefits of Emissions Trading: ? Enhance Air Quality w/o Economic Stagnation ? Encourage Development of New Technology ? Foster Most Efficient Use of a Limited Resource -- Clean Air § Contributes to Sustainable Development and objectives of UNFCCC, Kyoto Protocol?.

Nov 1, 2002

By P. J. Adams

Environmental regulations require means for controlling emissions of SO2 NOx and particulate when burning coal. The combustion of coal in limestone fluidized beds is one of the most promising techniques for the necessary reduction in emissions. Fluidized-bed firing, furthermore, offers potential economies in capital equipment. The world's largest steam generator applying fluidized-bed techniques was built under the sponsorship of ERDA and installed in Rivesville, West Virginia. This paper describes the design and discusses the start-up and development difficulties which were experienced during the period from initial operation to current readiness for commercial operation. Other developments leading to utility and industrial fluidized-bed steam generating equipment are reviewed. The future potential of this promising technique is discussed.

Jan 1, 1979

By R. A. Elliott

This paper describes the development of an infra-red ore dryer at the Mines Branch. The dryer utilizes an infra-red heat source mounted over a stainless-steel belt to dry ores and concentrates of varying particle size and moisture content. It has been found to ?be successful in meeting Mines Branch requirements of minimum dusting loss and ease of cleaning to decrease ,contamination between various batches of dried products. It is described with the hope that it might .prove useful in other laboratories where there are similar problems. It might have an application in the drying of concentrates containing high values where dust losses would result in a considerable loss of revenue; also for small batches of material or an intermittent drying problem.

Jan 1, 1958

By Richard Hurteau

Design and validation of an integrated guidance system for articulated ground vehicles is investigated. The development of an autonomous industrial vehicle must take into the account the specific geometry of these vehicles; they can be composed of a tractor with 1 or 2 trailers or of articulated type like LHD. Moreover the tractor-trailers type vehicles can have on-axle hitch configuration or positive/negative off axle configuration. The path-tracking of a tractor-trailer vehicle in restricted space is presented and discussed in this paper. Recent results obtained in simulation and validated by experimentation are also presented. These studies can lead to better ways of maneuvering an articulated vehicle in a restricted space or automatically executing of docking and parking maneuvers

May 1, 2002

By EJ. Reichhardf

The Molopo Farms Complex is a major, layered ultramafic/mafic, early Proterowic intrusion which is totally covered by sediments of the Karoo and Kalahari Fonnations and situated in southern Botswana and northeastern South Africa. The approximately 3000 m thick, generally fine- to medium-grained ultramafic and mafic cumulates are intrusive into equivalents of Thmsvaal Supergroup sediments and lavas. Multiphase defonnation resulted in tilting and segmentation of the Complex into individual tectonic blocks. Sr isotopes document at least two chemically distinct parental liquids which interacted in a complex manner to form an approximately 1000 m thick rhythmically layered succession which straddles the ultramafic/mafic boundary. Repeated mixing resulted in a complex cryptic layering pattern and numerous sulfide-enriched layers which contain significant PGE+Au concentrations.

Jan 1, 1994

By A. E. M. Warner, A. Vahed, P. J. Mackey

In the decade 2002 to 2012 some 6.7 million tonnes of new copper concentrate production capacity was brought on line, corresponding to 2 million tonnes of contained copper. This increase in concentrate supply necessitated the commissioning of a number of new copper smelters as well as the modernization and/or expansion of existing plants to meet the demand. This paper gives an overview of the copper extractive industry, reviews recent copper production trends and changes in the copper industry, including an examination of pyrometallurgical and hydrometallurgical technology developments. WorleyParsons has supported a number of the projects involved in these developments and this role is briefly discussed. The paper introduces a number of ideas related to possible future directions of the copper industry.

Jan 1, 2014

By Erin N. Legault-Seguin

The Lac des Iles Mine (LDI) is located approximately 100 km northwest of Thunder Bay, ON. The mine has been in operation since 1993. The initial mine production was 2,300 mtpd and increased to 15,000 mtpd following a mine expansion project that was completed in 2001. Effective Oct. 29, 2008, LDI was shut-down under care and maintenance due to low metal prices. Prior to shutting down, LDI was the only primary PGM deposit in operation in Canada and of the few found globally. The complex geology and physical properties of the deposit causes several challenges for the concentrator. This paper will discuss the solutions to the main challenges of attaining nameplate tonnage and achieve satisfactory Pd recovery and concentrate grades.

May 1, 2009