Search Documents

By H. Al-Kazzaz

The 2-mm butt joints of ZE41A-T5 sand castings were laser welded using 1.6 mm EZ33A-T5 filler wire and a continuous wave Nd:YAG system at a power of 4 kW, surface defocusing and various welding speeds, Compared with the base metal, the fusion zone showed significant grain refinement due to high cooling rate, No grain coarsening was observed in the heat affected zone (HAZ). The porosity area percentage and total solidification crack length in the fusion zone (FZ) were reduced as the welding speed increased from 4 to 7 m/min, Fusion zone area, total penetration depth, and weld width decreased with increased welding speed, The hardness in the FZ was similar to or higher than the base metal after a natural aging of about one year, but there was a drop in the hardness of the HAZ, The HAZ width decreased with increasing the welding speed, Tensile test showed that a joint efficiency of approximately 75 ? 90 % was obtained.

Jan 1, 2005

By D. Tao

The adverse effects of clay particles on coal and mineral processing processes such as gravity separation, flotation, filtration, and thickening are well known in the mining industry. In particular, the presence of ultra-fine clay particles deteriorates froth flotation performance, which has been attributed largely to slime coatings that inhibit bubble attachment and to adsorption of the frother and/or collector by the clay particles. The present study was conducted to evaluate the performance of clay binding agents developed by Georgia-Pacific Resins, Inc. in enhancing coal and mineral flotation performance. Mechanical and column flotation tests were carried out using coal and potash samples. Process parameters investigated include slurry solids percentage, impeller rotation speed, binder dosage, collector dosage, etc. Flotation results show that use of GP reagents significantly enhanced flotation efficiency under different conditions. The required binder dosage and conditioning time was about 1 lb/t and 0.5-1 min, respectively. More significant improvements in process performance were observed at higher solids percentage and higher impeller rotation speed.

Jan 1, 2006

By M. Wu, G. Plascencia, A. E. M. Warner, A. Vahed, T. A. Utigard

Nickel oxide granules formed by pyrohydrolysis of a chloride solution, were reduced in hydrogen. Below 400 °C, an incubation period was observed, followed by very slow reduction. In the temperature range from 400 to 600 °C, the rate of reduction increased with increasing temperature and increasing hydrogen pressure. Microscopic analysis showed that in this temperature range the reaction followed the shrinking core model. Above 600 °C, the reduction rate decreased noticeably before suddenly becoming very fast at and above 950 °C. Microscopy showed inner bands of metallization inside the outer metallic rim, indicating partial blockage of the interface between the reacted and un-reacted NiO core. At these temperatures, particle agglomeration and sintering were also found to take place. Surface segregation of sulphur may account for the slow down in reduction rate above 600 °C. From an industrial point of view, reduction should be carried out from 550 to 600 °C with as high a concentration of hydrogen as possible. If sintering and agglomeration are not of any concerns, reduction can be carried extremely fast at about 1000 °C.

Jan 1, 2005

By Zoltan F. Oszter

The design of belt conveyors is a well-known procedure and related formulae can be found in any handbook dealing with materials handling. Belting and conveying equipment manufacturer's catalogues and design manuals offer a wide range of detailed information which can be applied to most of our conveying problems. The aim of this paper, however, is to investigate the design of a specific type of belt conveyor, namely the long horizontal, or nearly horizontal, type. (The undulating type, with moderate lifts and drops, can also be included in this category.) Most of the long overland conveyors carrying ore from pit to processing plant, or those carrying over-burden to the disposal area, fit this description. A critical appraisal will show that reasonably accurate results can be obtained when tl1e familiar horse-power formulae are applied to this type of conveyor. The progress and new developments in the design of belt conveyors, which have resulted from the extensive research done in the past decade, will also be explored.

Jan 1, 1962

By E. Ghali, A. D. Bas

There is a lack of electrochemical studies of oxidized gold ores since the majority of previous studies were conducted with sulphidic gold ores. In this study, the influence of agitation and iron oxide minerals, i.e. magnetite, hematite, and maghemite on gold leaching was investigated by means of galvanic and passivation phenomena. Cyclic voltammetry studies of Roasted Gold Ore (RGO) in de-aerated electrolyte have shown one oxidation and one reduction reaction while three oxidation and one reduction peaks were observed with gold electrode. Galvanic coupling results by Zero Resistance Ammeter (ZRA) mode indicated that magnetite showed a negative effect on gold dissolution while maghemite and hematite showed a positive effect, relatively, as a result of higher galvanic corrosion rates. Generally, gold dissolution was found to increase in the initial 15 minutes. Increasing agitation speed from 100 to 400 rpm resulted in higher galvanic corrosion rates for RGO, magnetite, and maghemite electrodes, while 250 rpm was found to be optimum for hematite electrode. Passive products such as silver and iron-oxide were identified by XPS and SEM-EDS analysis, respectively.

Jan 1, 2015

By I. Thobadi, C. Pawlik, K. Bisaka, S. Mokoena, M. Erwee

The PyEarth™ process developed at Mintek has been demonstrated successfully at pilot scale. Nine tons of ore containing 2.3 mass % of total rare earth oxides (TREO) from a dormant mineralogically complex iron-rich ore deposit, was subjected to a concentrating smelting step in a 200 kW DC open-arc pilot furnace and the rare earths from the resulting slag were extracted via a hydrometallurgical route. This ore deposit is practically not amenable to extraction by conventional methods. The testwork results proved that the PyEarth™ process was able to optimize the extraction of rare earths while minimizing waste through the removal of iron as a saleable iron alloy. Reduction of iron to the alloy in the smelting step was found flexible, efficient, and controllable, while rare earths were left virtually unreduced in the slag phase. The slag chemistry is selected to optimize both the smelting and leaching performances as well as the alloy composition. Leaching of the resulting slag was found possible and most efficient in hydrochloric acid amongst other lixiviants tested.

Jan 1, 2017

By Yves Gratton

The International Commission on Large Dams (ICOLD) is a non-governmental International Organization which provides a forum for the exchange of knowledge and experience in dam engineering. It is the world's leading professional organization dedicated to advancing the technology of dam engineering and supporting socially and environmentally responsible development and management of the world's water resources. ICOLD was founded in 1928 and has National Committees in 82 countries with approximately 7,000 individual members who are engineers, geologists and scientists from governmental and private organizations, consulting firms universities, laboratories and construction companies. Its original aim was to encourage progession in planning, design, construction, operation and maintenance of large dams and associated civil works by collecting and disseminating relevant information and by studying related technical questions. Since the late sixties, focus was put on subjects of current concern such as dam safety, monitoring of performance, reanalysis of older dams and spillways, effects of ageing and environmental impacts. More recently, additional subjects have included cost studies at the planning and construction stages, harnessing international rivers, information for the public at large, and financing.

May 1, 2002

By Ian R. Muirhead

Over the past year or so, a number of mining companies have been meeting to examine the role of research in surface mining and, in particular, how to establish a collaborative research effort for the surface mining industry. A review has been completed which has identified the topics that are of interest to the surface mining companies for undertaking collaborative research. This has identified key subject areas such as Operations & Equipment; Maintenance; Environment & Reclamation; and Stability. Specific research projects for the initial research effort have been selected which include Wireless Data Communications, Analysis and Management; Application of GPS in Mining; and Tires for Heavy Haulers. In addition, attention has also been focussed on finding a suitable low cost, but effective, organization to coordinate and manage the collaborative research. The recently formed CONRAD Organization (Canadian Oilsands Network for Research and Development) appears to be a suitable candidate and discussions are ongoing with that group. This paper provides a summary of the review of surface mining research needs and of the status of the establishment of a collaborative research body for surface mining.

Jan 1, 1996

By G. P. Contractor

Medium and low carbon steels, modified with uranium, were studied in order to evaluate the influence of uranium on forge ability, mechanical 11roperties, response to heat treatment and microstructure. Uranium contents ranged up to 0.70 per cent. The medium carbon steels are hot short if the uranium content exceeds about 0.35 per cent. More uranium can be tolerated in low carbon steels. The hot shortness is caused by the formation of intergranular phase UFe2. Critical transformation temperatures, Jominy hardenability, and resistance to tempering are not significantly affected by the 11resence of uranium. Similarly, uranium has little or no effect on the tensile properties of carbon steels. The addition of uranium has a favourable effect 11n the stress-rupture characteristics and some beneficial effect on fatigue properties. However, more results are required for verification. In the steels investigated, it seems that most of the uranium carbide combines to form complex inclusions of U (0, C, N) or (C, N), rich in oxygen or nitrogen or both.

Jan 1, 1963

By K B. Bowley

This paper covers the application of a systematic maintenance plan by the Plant Engineering Department of Rio Algom Mines Limited, Milliken Division. The plan established the function of work study, developed and installed formal work planning and labour cost control procedures, and extended the existing preventive maintenance routines. In June, 1961, assisted by management consultants, a more scientific approach to maintenance was instituted. The emphasis was placed on the control of labour. The development and application of the primary control system was established with-in six months. Since then, the Department has operated for a year, consolidating the system. The procedure of the installation, the results achieved and the results to be expected will be discussed. JNTRODUCTION THE Milliken Division of Rio Algom Mines Limited operates a 3,000-ton-per-day uranium mine, in the Elliot Lake district of Ontario, which went into production in April of 1958. The lowest operating level is 3,000 feet below surface. Mining is carried out by open stopping, with planned pillar support and footwall haulage on rail.

Jan 1, 1963

By C. C. Walden, D. W. Duncan, P. C. Trussell

Thiobacillus ferrooxidans released copper from -400-mesh chalcopyrite at a rate of 54 mg/I/hr. Any flotation chemicals remaining on the concentrate did not inhibit the leach rate. Zinc rougher tailings were also leachable. With bacteria, 75 per cent of the zinc and 68 per cent of the copper came into solution. In the sterile controls, only 16 per cent of the zinc and 10 per cent of the copper were released; 100 per cent of the copper and 36 per cent of the zinc were leached from pyrite cinders through the action of bacteria, and 17 per cent of the copper and 10 per cent of the zinc were solubilized in the sterile controls. Less than 0.027 per cent of ~he iron came into solution. The majority of the copper in a converter slag was acid-soluble, but a reverberatory slag responded to microbiological leaching. About 62 per cent of the copper came into solution, compared to 12 per cent in the sterile control. The various factors influencing the rate and extent of microbiological leaching are discussed.

Jan 1, 1966

By David Runnels

The Mount Wright iron are mine and upgrading plant were brought on line in the fall of 1975. The mine is located near the Quebec - Labrador border some six hundred miles northeast of Montreal. This paper describes the crushing, grinding and concentrating facilities at Mount Wright, and some design: criteria used in equipment selection and flow sheet design. Also mentioned are some "asbuilt" modifications. A brief description of the over-all flowsheet is also included. Introduction IN SEPTEMBER 1970, the Quebec Cartier Mining Company started development of the Mount Wright iron ore mine. The estimated are reserve is in excess of 1,000,000 ,000 long tons of concentrates, with an average crude are grade of 31.5% Fe. The run-of-mine ore is crushed, ground and concentrated to a product having 66% Fe and 5% silica at an annual concentrate production r ate of 18.4 million long tons. The daily production rate of over 50,000 long tons of concentrate necessitates a daily mine output of approximately 250,000 long tons of material, of which 50% is waste.

Jan 1, 1977

By S. C. Tadolini, J. M. Goris, J. L. Gallagher

Cable supports offer several advantages over traditional secondary support methods by enhancing stress redistribution to pillars and gob areas, minimizing or eliminating timbers and cribs that reduce ventilation, eradicating material-handling injuries related to placement of crib supports, and providing a cost-effective alternative to secondary support. The U.S. Bureau of Mines (USBM), researching alternatives to traditional roof support methods, designed and installed high-strength cable supports to improve the stability of longwall gate road entries in a western U.S. coal mine. With the cooperation of industry, methods were developed to install and evaluate cable supports in a tailgate area using traditional resin cartridges. The cable-bolted areas successfully maintained roof support throughout the developed entries. Cable supports have replaced wood cribbing as secondary support in the bleeder entry system and have minimized or eliminated the use of cribbing in the longwall tailgate entries. This paper describes the theory, application, and advantages of cable supports and presents some mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1999

This work illustrates the potential of two welding processes for joining AA1100-16 vol.% B4C metal matrix composite: laser welding process using a 4 kW Nd:YAG laser and Friction Stir Welding. A comparison is made between these two welding techniques in terms of microstructure and mechanical properties of welded joints. A large amount of brittle needle-like phases, together with some residues of B4C particles were observed in the fusion zone of laser welded joints. The use of Ti filler can improve the microstructure and increase the joint efficiency from 63% to 75%. On the other hand, the friction stir welding process being a solid state welding technique is interesting as it avoids the formation of brittle intermetallic phases. In addition, the breakage of B4C particles and the grain refinement of the matrix were observed in the weld zone. Consequently, FSW joints show much better mechanical properties than laser welded joints. Up to 100% joint efficiency can be achieved by FSW for annealed AA1100-16 vol.% B4C materials.

Jan 1, 2011

By W. K. Coughlan

The Wabana deposit of Dosco Industries Limited is situated on the east coast of Newfoundland, at Bell Island in Conception Bay. It is a Clinton-type iron-formation of Lower Ordovician age. Five separate beds have been recognized, with others noted locally. Economic production has been obtained from the Lower, Middle and Upper beds, which are second, third and fifth in sequence, al-though at present only the Lower Bed is worked. The potential area of occurrence is about 70 square miles. It i;; bounded by major faults to the north, east and west and truncated by erosion at the south, where rocks of the de-posit crop out on the north side of the island. The iron is contained in oolitic hematite and chamosite, with minor siderite. As the deposit is submarine, conventional exploration methods are not applicable and much interpretation and projection from mined areas is necessary to guide exploration and development. With the interpretation of information from existing mined ores, it is possible, using a minimum of diamond drilling in advance of working faces, to maintain adequate ore reserves.

Jan 1, 1966

By W. Blum

Progress made in improving the creep resistance of Mg alloys is reviewed with the emphasis on microstructural interpretation. Experimental results on the increase of creep strain with time at constant stress a measured for limited times and strains are displayed in a transparent form as creep rate-strain diagrams from which the minimum creep rate stress is safely derived. In addition, data on the thermal stress component a derived from high-precision a-reduction tests are reported. Within a simple statistical dislocation model these data allow one to quantify the relation between dislocation velocity v and a . In combination with structure evolution laws this relation serves as a basis for modeling the creep rate. New alloys have distinctly higher creep resistance than AZ91 where precipitation hardening plays a minor role. This is due to hardening by intermetallic phases which may form a continuous skeleton along the grain boundaries (e.g. Ca-alloyed AZ91) and/or submicron-sized precipitates within the grains (MRI230D, Mg-Zn-Ca alloys).

Jan 1, 2006

By Engineering Staff

In 1958, the Iron Ore Company of Canada decided to proceed with the Carol Project. The ore deposits in the area are part of the highly metamorphosed southern zone of the Labrador Trough. They lie along the shore of W a bush lake, in the western part of Newfoundland-Labrador, 190 miles north of Sept-Iles. The project is designed to mine, by open-pit methods, 17,200,000 long tons of crude ore, grading 37 per cent iron, per year. This ore will be beneficiated to produce 7,000,000 long tons of concentrate, grading 66 per cent iron, of which 5,500,000 long tons will be pelletized. Production is scheduled to commence this summer. Initially, ore will be taken from 45-foot benches in the Smallwood mine, using jet-piercing production drills and large-scale blasting with "slurry" explosives. Four 13-yard electric shovels will muck the broken ore into 100-ton trailer trucks. The trailers will be hauled to two 2,000-ton loading pockets, which feed the ore into 100-ton railcars. Four ore trains, each comprised

Jan 1, 1962

By S P. Giambra

The 50,000-ton-per-day Concentrator and Crushing Plant, complete with its related water supply, tailings disposal and concentrate handling systems, was started up in a five-month period, with the entire plant obtaining its design capacity six months after the first mill became operational. Individual mill lines, with their spiral circuits, achieved design capacities within a week after the first treatment of ore through each mill. Construction and start-up proceeded together in many areas of the plant, and considerable organization and cooperation between the Owner, the Engineer and the Contractors permitted a smooth transition from construction to operation. PLANT DESCRIPTION THE Carol Lake Plant of the Iron Ore Company of Canada l1as been well described in various technical magazines. The purpose of this paper is to present a brief outline of the start-up of the con-centration complex. This start-up was accomplished in a period of five months, with the plant producing one million tons of concentrate and achieving its design-rated tonnage less than six months after the first ore was treated.

Jan 1, 1963

By Pizhi Zhao, Yingdong Li, Hailong Cao, Yingjuan Feng

"Three types of anodic films (unsealed, hot water sealed and agent sealed) were prepared to study the effects of anodizing pores structure on the adhesive bonding performance of AA5754 automotive sheets. The morphology of the anodic films was examined by using scanning electron microscope (SEM) and the composition was examined by glow discharge optical emission spectroscopy (GDOES). The adhesive bonding strength and durability in corrosive environment were investigated by using single lap shear test and salt spray corrosion test (SST), respectively. The results showed that the pores structure could significantly influence the adhesive bonding performance. The unsealed sample showed porous structure and provided high bonding strength, however, the durability was poor in corrosive environment. The hot water sealed sample showed fine and loose hydrated alumin a structure on the surface and provided high durability in corrosive environment, but the bonding strength was low. In contrast, the agent sealed sample provided both high bonding strength and durability in corrosive environment.INTRODUCTIONAdhesively bonded aluminum joints by using adhesives have been widely used for the realization of lightweight design in industrial applications like automotive and aerospace industry[1, 2]. Durable bonds which are capable of taking structural loads can be created due to a careful consideration of the way in which the joint is formed, the type of adhesive and the appropriate treatment of the adherend surfaces prior to bonding[3-6]. Experiences demonstrate that the surface treatment is the most critical step which could not be disregarded, since it is essential to achieve long-term service capability [7].In structural applications, a bonded assembly is expected to maintain a significant load and may be combined with exposure to harsh environmental conditions in its service life. For this purpose, the pretreatment for structural bonding of aluminum alloy must provide not only strong tensile strength and durability but also good corrosion resistance. Chromic acid anodizing (CAA) process provides an anodized layer which has good corrosion resistance while also exhibiting useful adhesion characteristics as well as lacquer coating retaining characteristics[8].However, the use of Cr (VI) is unadvised from a health and environmental point of view since it is toxic and carcinogenic, and this process is gradually limited even prohibited. Boeing's phosphoric acid anodizing(PAA) process provides a more open pore structure allowing penetration of high molecular primers/adhesives[8]and PAA process is the most widely used pre-surface treatment suitable for adhesive bonding between aluminum alloy components. Rahimi et al. demonstrated that nanostructure can be produced by PAA process and is affected by the time of pretreatment and anodizing parameters [9]. Xu et al.investigated the influence of surface energy and roughness on adhesive bonding through PAAprocess and provided improved adhesion performance under certain anodizing parameter[10]. However, PAA process is normally not recommended for a major concern of deterioration of the mechanical performance of the joints as a result of exposure to a wet and corrosive environment. Sulfuric acid anodizing(SAA)process, recently, has been widely used for corrosion protection and good base coating for the adhesion of lacquers in aerospace manufacturing[11]. The good performance is explained by properties such as the porous morphology and high adsorptive power of the oxide film, the chemical and electrical inertness of the anodized layer. Moreover, modified sulfuric acid could also used for adhesive bonding. Lunder et al. found that anodizing in hot sulfuric acid is promising as a simple, very rapid and environmentally friendly pre-treatment for adhesive bonding[12].Saeedikhani et al. studied the process of phosphoric/boric/sulfuric acids anodizing and found it was is a promising pre-treatment for adhesive bon"

Jan 1, 2018

By J. F. Wang, Y. Jin, Z. L. Wang

Smelting reduction as an ironmaking technology for the 21st century has been challenging the traditional blast furnace. The process has many attractive advantages over the blast furnace, however, the massive by-produced coal gas mainly containing CO, H2 and CO2 requires further treatment. From a chemical engineering view, coal gas is a valuable chemical stock and can be transformed into hydrogen-rich synthesis gas. Hydrogen can be directly used as clean fuel and synthesis gas can be used for the production of some important chemicals such as methanol, ammonia and dimethyl ether. Among those chemicals, dimethyl ether as an alternative clean fuel for diesel engine and liquefied petroleum gas has been drawing more attention. It has excellent environmentally-benign behaviours not only in compression ignition combustion, but also in the much lower emission of SOx and NOx. In this work, a combined technology of smelt reduction ironmaking and direct synthesis of dimethyl ether, which will strongly promote the energy efficiency, environmental protection and resource recovery, is proposed and described in detail.

Jan 1, 2004