Search Documents

By Lang Tao, Jun Wang, Wei Xiao, Wenqing Qin, Pan Cao, Guanzhou Qiu, Key Lab of Biohydrometallurgy of Ministry of Education, Central South University

"The effect of metal cations on the rutile flotation using styryl phosphoric acid (SPA) as the collector was investigated by micro-flotation test, bench scale flotation test, zeta-potential measurements and adsorption measurements. The micro-flotation results indicated that Fe (?) and Al (?) ions in low concentrations had obvious activation on the rutile flotation, and Pb (?) ions in low concentrations had smaller activation of rutile, but Fe (?), Al (?), Pb (?), Ca (?) and Mg (?) have strong inhibition of rutile flotation in high concentrations. The bench scale flotation results indicated ethylene diamine tetraacetic acid (EDTA), boracic acid, and sodium hexametaphospate can decrease the metal ions concentrations, and increase the recovery of rutile flotation. Adsorption measurements and zeta-potential measurements revealed that Fe (?), Al (?) and Pb (?) ions were adsorbed on the rutile surface, and had interaction with SPA. But when these ions concentration were over the largest adsorption capacity, residual metal ions could occur chemical reaction with SPA.INTRODUCTIONRutile is one of the favored minerals for production of titanium dioxide white pigment, primarily through the chloride manufacturing process (Stanaway 1994; Hou et al., 2013) However, the majority of rutile ores belong to refractory ores, while flotation is one of the most efficient methods to separate fine rutile from gangue (Dolbear et al., 1937). With the flotation development, many effective collectors were successfully applied in the oxide ore. Many reviews have indicated that organic phosphonic acid collectors showed good selectivity on oxide ores such as ilmenite and rutile (Bulatovic & Wyslouzil 1999; Liu & Peng 1999).It is inevitable that many types of metal cations are present in ore pulp. These metal cations significantly influence the flotation of minerals. Liu et al. (2015) showed that Ca2+ and Mg2+ could improve the floatability of spodumene at pH 12.5 and 10.0, respectively. The authors proposed that Ca2+ and Mg2+ ions readily form hydroxy complexes (CaOH(l) and MgOH(l)) and precipitates as (Ca(OH)2 and Mg(OH)2) in strongly alkaline solutions. Fan and Rowson (2000) investigated the effect of Pb(NO3)2 addition as an activator on ilmenite flotation and showed that it could improve ilmenite floatability. The addition of Pb(NO3)2 resulted in an increase of ilmenite zeta potential in both weakly alkaline and acidic aqueous solutions. Mehdilo, Irannajad, and Rezai (2015) studied three kinds of ilmenite of different origins and discovered that both Mg and V had a negative correlation with ilmenite flotation, while the Mn content seemed to correlate positively with flotation efficiency. A number of studies have also showed that Fe3+ can improve the floatability of ilmenite (Fan et al., 2009; Nuri, Mehdilo, & Irannajad, 2014)."

Jan 1, 2016

By Mohsen Mohammadi, Edward Cyr

"To date, several studies have been performed on the static mechanical properties of SLM-AlSi10Mg alloy. There have also been more recent studies on the relation between scan strategy, texture, and mechanical properties of SLM metals and composites. However, there is a huge knowledge gap in the available literature regarding texture and mechanical behavior of SLM-AlSi10Mg alloy under high strain rates. Therefore, in this study, dynamic mechanical behavior of AlSi10Mg_200C alloy manufactured by DMLS technique was investigated at high strain rates ranging from 900/s to 1700/s using Split Hopkinson Pressure Bar. Texture using X-ray diffraction technique of the initial samples were measured. The yield strength, peak flow stress, and ductility increased in all samples with increase of strain rate. TEM studies have also revealed evidence of continuous dynamic recrystallization in grains after 900/s–1700/s strain-rate tests. A Taylor polycrystal crystal plasticity constitutive model was then developed to capture and predict the texture evolution and mechanical response under dynamic loading, using plastic work as a critical parameter for the onset of recrystallization.INTRODUCTION Additive manufacturing (AM) powder techniques are among the fastest advancing breakthroughs in manufacturing in recent years, defined by a bottom-up layer by layer process of joining with energy input from lasers or electron beam (Herzog et al., 2016; Gibson et al., 2015). Among alloys fabricated by SLM, AlSi10Mg is of high interest to industry and academia due to its low density, high specific strength and excellent corrosion resistance, making this alloy a viable contender for aerospace, automotive, and marine applications. Circumstances such as car crash or bird aircraft strike hazards subject potential additively manufactured AlSi10Mg parts to impact loadings. This drives an interest in understanding and predicting dynamic behaviour of these alloys. AlSi10Mg is the AM counterpart of A360 die-cast aluminum, which possess hypoeutectic microstructure (Li et al., 2015). Up to the present time, many studies have presented the mechanical properties of SLM-AlSi10Mg alloy. The mechanical properties and microstructure of AlSi10Mg produced by selective laser melting (SLM) or DMLS techniques can be controlled using different parameters, such as feedstock powder (Asgari et al., 2017), and process parameters (Olakanmi et al., 2015). The microstructure and mechanical properties of AlSi10Mg can also be controlled using post heat treatment after SLM process Li et al., 2016). The mechanical properties of SLM-AlSi10Mg are sensitive to strain rate and can both change under quasi-static (Rosenthal et al., 2017) and high strain rates (Asgari et al., 2018). However, a significant knowledge gap in available literature regarding modeling these behaviours, and especially micromechanical modeling of dynamic behaviour."

Jan 1, 2018

By R. Charlier, G. Radioti, J. -P. Radu, S. Delvoie, F. Nguyen

"In order to investigate the fracturing of the bedrock and its possible heterogeneous distribution in situ, four boreholes equipped with double-U geothermal pipes of 100 m long were installed on the campus of the University of Liege (Liege, Belgium) over a surface area of 32 m². The bedrock, which starts at a depth approximately of 8 m, is quite fractured and consists mainly of siltstone and shale interbedded with sandstone.Different geophysical methods are applied at two different phases, after drilling the boreholes and after injecting the grouting material. The first approach consists in lowering an ultrasonic borehole imager (borehole televiewer; Zemanek, Glenn, Norton, & Caldwell, 1970), an instrument that acts as an ultrasonic transducer and receiver, into the boreholes to obtain high-resolution, continuous images with 360° coverage of the local geology and fracturing. Moreover gamma-ray logs of the four boreholes are obtained and inclinometry is conducted.After drilling the boreholes fiber optic cables are attached along the pipe loops and the double-U pipes are installed inside the boreholes. Then the grouting material is injected. The second approach consists in measuring the temperature along the fibers by applying the Distributed Temperature Sensing technique (Soto, Sahu, Faralli, Bolognini, Di Pasquale, Nebendahl, & Rueck, 2007). A laser pulse is injected into the optical fiber and the temperature along the fiber is determined by the intensity of Raman stokes and anti-stokes reemitted signals. Temperature evolution is measured during hardening of the grouting material. Local maxima of the temperature curve are probably due to a local lower thermal conductivity and/or a local larger quantity of grouting material due to gathering of fractures.A detailed fracture characterisation (position, opening, orientation, dip angle) is obtained based on the acoustic signal travel time and amplitude. The fractures are characterised by the same dipping and orientation but significantly vary in number and location in the four boreholes, despite the close distance between them. Gamma-ray data and observation of the cuttings during drilling result in rock identification through depth as well as in determination of the layer dipping. The inclination of the four boreholes tends to be perpendicular to the dipping. The combination of the two geophysical methods as presented provides information useful for the hydro-thermo-mechanical behaviour of the bedrock. The contribution of the thermal behaviour of borehole heat exchangers to bedrock investigation will be further studied by conducting Distributed Thermal Response tests (Fujii, Okubo, & Itoi, 2006). During the tests we will measure the temperature variation thanks to the installed fiber optics. These data will allow us to correlate any anisotropic thermal behaviour to the geological characteristics. The available information could be used for a detailed numerical model."

Jan 1, 2015

By Wei Sun, Xiangsong Meng, Xiaodong Li, Weisheng Huang, Yuehua Hu, Chonggao Cao, Haisheng Han, Wensheng Chen, Runqing Liu, Central South University

"The similar flotability of scheelite, fluorite, and calcite resulted in the difficult separation by flotation. This work revealed the effect of water glass on the flotation of scheelite by FTIR and the wettability change of the usual cleavage plane, and proved that water glass inevitably influenced the flotation of tungsten minerals to a large extend in traditional fatty acid flotation process. A new collector, benzohydroxamic acid complexes, was found to be selective for the separation of scheelite and calcium minerals with little water glass. Hence a novel flotation process was developed for the recovery of tungsten minerals in shizhuyuan mine in China. Normal temperature flotation of tungsten minerals was developed to instead of the classical “Petrov's process” for scheelite-calcite-fluorite type ores. Compared with the traditional process, the recovery was improved by 10% and the grade of scheelite concentrate was above 55%. The disappearance or decreasing of water glass contributed to improving the recovery of tungsten and fluorite and the circulation of water and reagents.INTRODUCTIONChina is rich in tungsten resources and the proved reserves accounted for 60% of the world's reserves (Cai Gaipin et al., 2009). However the wolframite has been dried up and the scheelite resource has become the main resource of the tungsten metal. Scheelite deposits were classified to scheelite-silicate type and scheelite-calcite-fluorite type based on the associated gangue minerals. Scheelite was easy to separate from the silicate minerals. Flotation separation of scheelite from calcium minerals creates difficulties because of the existence of the same cation in the minerals and similar physicochemical characteristics such as solubility, hardness, specific gravity, PZC (point of zero charge) etc.(Arnold & Warren, 1974; Yongxin & Changgen, 1983; Ozcan & Bulutcu, 1993a; Deng et al., 2015, 2016;). The conventional collectors used in the flotation of scheelite ores are generally fatty acids or fatty acid derivatives ( Yongxin & Changgen, 1983; Oliveira & Sampaio, 1988; Sivamohan, 1988; Shi et al., 2014; Bo et al., 2015). It is difficult to separate scheelite especially from calcite with these reagents because the adsorption mechanism of these collectors occurs through chemisorption of the oleate ion onto the mineral surface (Atademir et al., 1979; Changgen and Yongxin, 1983; Hiçyìlmaz et al., 1993; Hu et al., 2011). Therefore, it is almost impossible to separate them by fatty acid flotation without using any selective depressant. Although oleoyl sarcosine was used as a selective collector in the flotation of fluorite and siliceous scheelite ores (Ozcan & Bulutcu, 1993b; Ozcan et al., 1994), this selectivity is not adequate for a low-grade calcitic scheelite ore. Unfortunately, the reagents such as organic colloids (dextrine, starch), quebracho, sodium phosphates, sodium silicate solutions containing polyvalent cations (hydrosols), etc. (Yongxin and Changgen, 1983; Schubert et al., 1990; Shi et al., 2014; Bo et al., 2015) used for calcite depression also depress scheelite to a large extent."

Jan 1, 2016

By P. Miranda, K. Le, G. Maes, R. Peters

"The Mount Milligan Mine, owned by Thompson Creek Metals Company Inc. (TCM), started operations in September of 2013. It is located between the communities of Fort St. James and Mackenzie and is the first major metal mine to open in British Columbia in 15 years. Based on reserves as of January 1, 2014, it has an estimated 22 year mine life with 2.1 billion pounds of copper and 6 million ounces of gold in reserves. Like all commissioning operations, there have been issues achieving design throughput and recovery due to flow sheet design, equipment failures, control philosophy, and reagent scheme. Efforts to improve overall mill performance include equipment modifications, reagent screening and testing, and grind size testing. Applying these changes to the mill and working closely with the mine has resulted in continuous improvement each month as Mount Milligan looks to achieve the nominal design capacity of 60,000 dry metric tonnes per day in the later part of 2015. Considerable focus is being placed into ensuring size reduction equipment is utilized effectively. Additional modifications and tests are being undertaken to steadily improve processes and alleviate restrictions in the mill. This paper will discuss the start-up and present ramp-up history of Mount Milligan, the current mill processes, and the steps taken to achieve expected production numbers.OPERATION BACKGROUNDMount Milligan is an open-pit copper and gold operation wholly owned and operated by Thompson Creek Metals. It is located approximately 155km northwest of Prince George, British Columbia, between the communities of Mackenzie and Fort St. James. The copper-gold porphyry deposit contains a Measured and Indicated Mineral Resource of 706.7 Mt at 0.18% Cu and 0.33 g/t Au, containing 2.84 billion lb. copper and 7.50 million oz. gold. Mine life is currently estimated at 22.1 years (“Feasibility Update – Mt. Milligan,” 2009). The mill is designed to process 60,000 dry metric tonnes per day and produce 400 dry metric tonnes of concentrate per day averaging 25.5% Cu and 40 ppm Au. Concentrate is delivered by truck and trailer to Mackenzie followed by rail to Vancouver for overseas shipping to various customers.Mount Milligan is considered a “zero discharge” operation meaning no process or surface water will be discharged to the environment. As well, stockpiling is very limited and is only permitted for a short period of time. This scenario presents several unique challenges. Scheduling of ore/waste production must be carefully planned as waste rock is used to build the tailings storage facility (TSF). Reagent selection is also important as persistent chemicals will have a tendency to build up in reclaim water which feeds the process water tank."

Jan 1, 2015

By Henk Dijkman, Wageningen University, Paula Gonzalez Contreras, Irene Sánchez-Andrea, Jan Weijma, Silvia Vega

"More than 20 years ago, Paques B.V. introduced innovative biotechnologies to recover metals and to remove sulfate from aqueous streams. These technologies find their origin in the exploration of microorganisms involved in the global sulfur cycle. Currently, several sulfur cycle biotechnologies are applied successfully at full-scale. The sulfur cycle is closely linked with the iron cycle, and also the latter offers opportunities for application of innovative biotechnology for the mining industry. Microorganisms of the natural iron cycle carry out reactions that are not feasible by chemical methods such as ferrous iron oxidation with oxygen at pH below 4. Iron oxidation with oxygen can be conducted using microorganisms living at pH between 0.5 and 7 and at temperatures between 0 and 95ºC. Remarkably these microorganisms can also carry out arsenite oxidation at similar acidic conditions and high temperatures. Making use of the extreme features of these microorganisms, Paques and Wageningen University have developed a biological process to precipitate arsenic as scorodite. This biological formation of scorodite is a novel combination of biological oxidation and biocrystallization. Depending on the level of saturation, biological oxidation rates and operational conditions, we could control the formation of the iron precipitates such as jarosite and scorodite. Currently new microorganisms have been harvested from hot springs and rock acid mine drainage to foster the growth of specialized microbial communities with potential high iron and arsenic oxidation capacities and higher resistance to other metals. In our paper we address the ongoing research and development of the bioscorodite process.THE USE OF IRON TO REMOVE ARSENIC In 2015 several environmental disasters related to the release of mine wastewater and tailings occurred. On August 5th, a waste water spill occurred from the Gold King Mine near Silverton, Colorado. A dam holding the tailing pond was damaged and spilled three million US gallons (11 ML) of mine wastewater and tailings, including elements such as cadmium, lead and arsenic, into Cement Creek, a tributary of the Animas River in Colorado. “At their peak, arsenic levels were 300 times the normal level and lead was 3,500 times the normal level” (The Guardian, 2015). In early November, another collapse of a mining dam in the Brazilian state of Minas Gerais spilled between ten and sixteen thousand US gallons of water and sediment after a dam failed from an iron ore mine. Arsenic and mercury polluted the Doce River, arsenic levels were found more than ten times above the legal limit in some places of the river (The Guardian, 2015). Waste production is inevitable during Mining. However, a preventive waste management strategy could have minimised waste production, maximised waste reuse and classified waste by their hazardous degree."

Jan 1, 2016

By M. J. A. Ruszala

Aggregates production is a huge global industry which uses an enormous amount of energy and produces a massive amount of unsalable fines. Reducing the amount of energy used per tonne of product and/or the amount of fines produced, would make a quarry more efficient. This reduction would make the quarry more environmentally friendly and profitable. This research looks at modelling Mountsorrel Quarry, a granite quarry in the United Kingdom (UK), using JKSimMet and Split-Desktop software packages in conjunction with the European Union (EU) project, EE-Quarry. Samples submitted to drop weight tests confirmed Mountsorrel Quarry granite as an extremely hard granite. Rock fracture data (t10) and energy of comminution (ECS) data were obtained from analysing the results. Split-Desktop image analysis software was utilized to determine the particle size distribution (PSD) of the primary crusher feed, as it contains particles too large to screen manually. It was also found that <1% of the feed is fines, which at Mountsorrel Quarry are classed as particles smaller than 5 mm, and that no particles were larger than 3,810 mm. JKSimMet was used to create a flowsheet of Mountsorrel Quarry. The crusher product PSDs were simulated and found to have strong correlations with experimental data, calculated by screening samples from conveyor belts, especially in the fines region, with a mean difference of 1%. The simulated primary crusher product PSD showed that it contains ~6% fines. A simulation over the entire quarry showed the product to be within the size range produced at Mountsorrel Quarry, and with a simulated fines content of 13%. When the CSS on the primary crusher was altered from 165.1 mm (the operating size on site) to 100.0 mm, it increased the overall percentage of fines produced by 3%, increased the power draw by 140.6 kW, but reduced the overall plant production percentage of fines by 2%. Two blasts were analysed on adjacent rock faces. They had identical blast designs, but the order of deck detonation varied; the first blast detonated the bottom deck before the top and vice versa in the second blast. For each blast, measurements of the feed PSD to the primary crusher, the number of particles that required secondary breakage on the quarry floor, acoustic levels and vibration readings were measured. No significant difference was identified between the two blasts in any of the parameters measured. In conclusion, a working model of Mountsorrel Quarry has been made in JKSimMet that has been validated against data from site and Split-Desktop has been used to simulate the primary crusher feed PSD, something that was previously unknown. The effect of reversing the order of deck detonation in a two deck blast was also analysed but with no significant difference between the two blasts found.

Aug 1, 2013

By Z. Zhong, Y. J. Hu, D. Elsworth

"A standard triaxial apparatus was set up to perform sliding tests. Slide-hold-slide (SHS) tests, with hold times from 10 to 3000s and at invariant effective confining pressures of 1MPa, incremented to 3MPa and then 5MPa, were conducted on both dry and wet split limestone samples to study the evolution of fracture friction under holding and sliding processes. Limestone fracture shows time-dependent behaviors in SHS tests, friction drops (creep) gradually during hold periods, and recovers (healing) after re-slide. Frictional healing and creep increment are proportional with hold times, while are inversely proportional with effective confining pressures. Moreover, the wet sample displays heavier healing than the dry one, whereas creep increment of the wet sample is lighter than the dry one. We conclude that the evolution of limestone fracture friction is significantly controlled by mechanisms of fluid-rock interactions.INTRODUCTIONThe evolution of the mechanical properties of fractures and faults exerts a critical influence on the behavior of fault zones and on the earthquake cycle. In addition to natural processes, this behavior has broad implications in induced seismicity and influences oil and gas production, the sequestration of carbon dioxide and the disposal of nuclear wastes.Fault friction is typically measured by slide-hold-slide experiments, where fault gouge is deformed at low velocities (<0.1 mms-1) and over small shear offsets (<30 mm) (Dieterich, 1979, 1981; Mair et al., 1999; Marone, 1998, 2004) or alternatively with rotary-shear devices, that enable higher slip velocities over very large shear offsets (Hirose & Shimamoto, 2005; Mizoguchi et al., 2006). Typical experiments (Dieterich, 1972; Marone, 1998; Olsen et al., 1998; Bos & Spiers, 2002; Tenthorey et al., 2003) show significant creep during the holding period and frictional healing (strength gain) upon reloading. Fault creep and healing are often time-dependent with longer hold times typically resulting in greater magnitudes of creep and in strength gains (Tenthorey et al., 2003; Yasuhara et al., 2005; Carpenter et al., 2012). Frictional healing may arise from growth of grain contacts (potentially induced by pressure solution) (Rabinowicz, 1951; Dieterich & Kilgore, 1994; Yasuhara et al., 2005), strengthening of the contacts (correlates with cementation) (Hickman & Evans, 1992; Beeler et al., 1994; Karner et al., 1997; Olsen et al., 1998; Muhuri et al., 2003; Tenthorey et al., 2003; Li et al., 2011) or via other changes in state including changes in porosity and rearrangement of force chains. Experimental evidence (Dieterich, 1979, 1981; Johnson, 1981; Marone & Scholz, 1988; Marone, 1998; Saffer & Marone, 2003; Moore & Lockner, 2007; Ikari et al., 2007; Ikari et al., 2011; Carpenter et al., 2012) quantifies both the mode and magnitude of second-order changes in the velocity-dependent (including velocity- strengthening and weakening) evolution of frictional strength."

Jan 1, 2015

By G. Barr

"The Polymetallic Twin Metals Project deposits in Northern Minnesota are being developed by Twin Metals Minnesota. Amongst the flowsheet alternatives being examined at a prefeasibility study level is one involving flotation of a bulk concentrate followed by high temperature autoclaving of the concentrate using the PlatsolTM Process to solubilize all the valuable metals in the concentrate (Cu, Ni, Pt, Pd and Au). Autoclave operating conditions have been established in which recoveries of all the pay metals are in the 92 to 99% range, and the autoclave residence time has been reduced to an hour. The stability of the precious metals in solution after autoclaving has been assessed, as well as the impact of internally recycling process liquors to the feed to the autoclave.INTRODUCTIONPlatinum group metals (PGMs; platinum, palladium, rhodium, ruthenium, iridium and osmium) are traditionally recovered from their ores by production of a high-grade concentrate by flotation and/or gravity concentration followed by smelting of the concentrate. Concentrates are smelted to remove nonsulphide minerals and converted to remove iron and sulphur. The resulting high PGM grade matte is processed hydrometallurgically to leach the base metals, leaving a residue with a very high grade (20-40%) PGM concentrate for final refining to individual PGMs. Due to the complexity of this process and its high capital cost, this process can only be applied economically to high grade PGM ores. Lower grade PGM concentrates might be accepted as copper and nickel concentrates but may not yield attractive payment terms for the PGMs. The mineralized Duluth Gabbro region of Minnesota hosts several low grade base and PGM deposits and Twin Metals Minnesota is working to develop the Twin Metals Project deposits. Earlier studies at both pre-feasibility and feasibility level, by other mining companies, have failed to yield an economically viable project based on the traditional process. It is possible to produce a saleable copper concentrate from these ores, but economic recovery of nickel and PGMs into saleable concentrates proved elusive.In the late 1990’s and early 2000’s the Platsol™ process was developed at SGS in Lakefield, Ontario (at the time Lakefield Research Limited) for the NorthMet deposit (also within the Duluth Gabbro) owned by PolyMet Mining. The process developed was a high temperature chloride-assisted pressure oxidation process capable of dissolving simultaneously the base metals (Cu, Ni, Co, Zn), gold and the PGMs."

Jan 1, 2012

By Xiang Li, Xibing Li

It is paramount that the stability of rock slopes be correctly accounted for under diverse operating and environmental conditions. Owing to different sources of uncertainty entailed in such stability problems, conventional deterministic approach through the calculation of a factor of safety (FOS) cannot reflect quantified uncertainties explicitly and sufficiently. Thus it is highly desirable to invoke the reliability approach to consider uncertainties in a systematic manner. Nowadays, the current design standards have an increasing tendency to ensure rock slope stability by pre-defining a target reliability index (or target probability of failure), viz., the reliability level of a rock slope is pre-set as a target to be satisfied. In such a situation and considering the fact that the FOS used as an indicator of slope performance still has a very wide acceptance, we focus on proposing an inverse-reliability-based methodology which aims at developing a two-fold indicator strategy, i.e., using the FOS and reliability together to deal with slope stability problems. The basic idea behind it is to utilize a so-called inverse first-order reliability method (IFORM) to directly calibrate the FOS provided the target reliability index has been given. In this way, the calibration scheme relating the FOS can be rationally done by not only incorporating uncertainties, but also satisfying a desired level of the prescribed reliability. Based on this, to make the IFORM computationally feasible and also reduce its computational cost, we introduce the response surface method (RSM) to generate a surrogate for the FOS-based limit state function (LSF), considering the lengthy and complicated form of the FOS in some recognized methods (e.g., within the framework of limit equilibrium). Distinguished from the existing RSMs that potential inadequacies may arise, we present an RSM based on a hybrid approach combining support vector machine (SVM; used as a regression technique) and uniform design (UD; pertaining to experimental design). Using a representative example of rock slope stability problem, we demonstrate the feasibility and validity of the developed methodology, during which the associated sensitivity study and further discussion are also performed. By dint of such a methodology, we can establish a link between the conventional deterministic approach and the reliability approach, where a logical and realistic framework is provided, for cases achieving the specified reliability, to assist in selecting the FOS which remains adequate for rock slope stability even in the face of uncertainty.

Jan 1, 2015

By John Kostuik

AT the Sladen-Malartic mine, a number of orebodies have been mined, some by shrinkage and others by open sub-level scopes, from which the ore is handled either through a grizzly system or by mechanical loaders. This paper deals with the comparative costs and relative merits of the two handling arrangements. The facts brought out in this comparison have a bearing on the selection of a proper handling method. The mine is in Fourniere township, northwestern Quebec, about forty miles east of the town of Rouyn. It is served by the Rouyn-Senneterre branch of the Canadian National railways. Two vertical three-compartment shafts give access to the present workings. No. 1 shaft, at which the plant is centralized, is the main hoisting shaft, with five levels to 950 feet. No. 2 shaft, 2,400 feet east of No. 1, is under development, with four levels to 725 feet. At the main shaft, the ore is hand-trammed in 1 1/2 tons cars from the scopes to the stations o:i each level and hoisted in cages to surface at a rope speed of 900 feet per minute. Air-operated tipples are used to dump the ore through grizzlies of 14-inch openings into a surface bin of 150 tons capacity. The ore hoisted at No. 2 shaft is trucked from the headframe bin to the mill. Milling commenced in January, 1938, ar a daily rate of 250 tons. Within two months this rate was increased to the unit&apos;s maximum capacity of 325 tons. A second unit to treat a further 325 tons daily was installed in April, 1939. The orebodies mined at No. 1 shaft are parts of a silicified zone at the contact between syenite porphyry and greywacke. The zone is ten co sixty feet wide, strikes easterly, and dips to the south at 55 to 85 degrees. The hanging-wall of the zone is marked, though not precisely, by a strong gouge fault. Locally, the boundary of silicification may be as much as twenty feet either above or below the fault, but for practical mining purposes the fault is the hanging-wall of the ore-zone. The footwall roughly parallels the fault, but as an assay wall it is usually irregular in detail. The ore is dense and hard, a siliceous replacement of both porphyry and greywacke, mineralized with fine disseminated pyrite.

Jan 1, 1941

By M. W. Grabinsky, J. H. Curran

"Characterizing the spatial distribution of rock stresses is a challenge, especially in the geologically complex environments typically found at most metalliferous mines. Therefore, instead of focusing, specifically, on the task of making stress measurements, the engineer should instead attempt to develop a better understanding of the interaction between stress, mining geometry and rock mass behaviour. This paper demonstrates such an approach using a Canadian Shield hardrock mine case study, in which geomechanical models are used to relate stress, mining geometry, and rock mass properties to observed excavation response, and numerical modelling is used to better quantify this interaction.IntroductionUnderstanding how the mine geometry, field stresses and rock mass interact to produce the observed rock mass response to mining can be a significant challenge. Consider our present ability to quantify the basic geomechanical design input data. Mine geometry is normally quantified in more detail than is required for analysis purposes. Our understanding of rock mass strength and stiffness is far from complete, but established procedures do exist to obtain estimates of these parameters based on index and laboratory testing data and field mapping. Our ability to quantify field stresses is probably the most limited, in part because stress measurements are difficult and expensive to carry out, and in part because the stresses vary to an unknown degree from point to point within the rock mass. The engineer must, therefore, consider whether or not stress measurements are justified and, when they are, where the average stress state needs to be quantified and how many of which type of measurements will be required to determine the average stresses.Such was the case at Ansil mine, a massive sulphide deposit in hard rock located at a depth of more than one kilometre in the northern Québec portion of the Canadian Shield. The Ansil orebody was relatively rich, but small, with the potential for significant stress-related problems. As a result, geomechanical design had to be done carefully from the start – there would be little opportunity to modify the mining strategy once production had begun, and the economic consequences of stope dilution and rock mass instability would be severe. An extensive stress measurement campaign was carried out, but the determined stress magnitudes were unexpectedly low. The designers were, therefore, faced with a dilemma:"

Jan 1, 1997

By A. K. Chetin, W. W. Fitkin

"The reservoirs of Mississippian Mi-dale beds and Frobisher beds found in the Weyburn field lie at the north-western termination of a broad productive belt extending 120 miles along the northeastern rim of the Williston basin. These carbonates, and inter-bedded evaporites, originated during cycles of marine transgression and regression, and were deposited as rock types characteristic of shoal, lagoon, and basinward shelf environments. The Frobisher-Alida Beds, which form a secondary reservoir to the main Midale Beds of producing zone are composed of oolit1c, fragmental-bioclastic, vugular limestone capped by an impervious dolomitic mudstone. Production is controlled by localized structural features resulting from de-positional build-up. Excellent reservoir conditions are accompanied by an active water drive. The Frobisher Evaporite, consisting of massive primary anhydrite with dolomitic veinlets, forms the floor seal for the Midale beds oil accumulation. A significant facies transition into an oolitic, bioclastic, vugular limestone characterizes this unit. Beyond the depositional margin of the evaporitic facies, marked increases in porosity and permeability of the en-tire reservoir are noted. Carbonate units overlying the areal extent of the Frobisher Evaporite exhibit a greater degree of metasomatism, dolomitization, and more abundant secondary anhydrite.Porous carbonates comprising the producing zone of the Midale beds are divided into an oolitic, fragmental bioclastic, vugular limestone, and an overlying granular marly lime-stone unit, capped, by the Midale Evaporite. Oil is accumulated in a stratigraphic trap bounded above and be-low by primary anhydrite and truncated by the post-Mississippian erosional surface. Mississippian strata dip basinward from this erosional surface in a broad homocline exhibiting only minor irregularities. Rapid lateral and vertical porosity and permeability variations are common. Localized, separated, porous lenticles contain interstitial water in areas where the Midale beds are underlain by the Frobisher Evaporite. The major portion of the field, however, is capable of water-free production. Bottom and edge waters are found in certain portions of the field. Productive limits are tentatively defined around most of the present field perimeter. A large area along foe southern edge of the field remains open to future development. Probable ultimate remaining recoverable crude oil reserves, as of September 30th, 1958, were estimated by Mc-Daniel Consultants Ltd. to be in excess of 330 million barrels."

Jan 1, 1959

By J. E. Ryan

General Description Due to the extreme cold weather experienced in Flin Flon during the winter months, thought and precaution were necessary in the design of the plant buildings. The machine shop, carpenter shop, drill shop, and coal plant buildings are similar in the building materials used in their construction. They are sided with two-inch shiplap, insulated with celotex and asbestos paper, and covered with corrugated iron on all side-walls. Roofing consists of 2 by 4 lumber on edge, laminated, and further covered by celotex and three-ply roofing. These buildings are heated by means of unit heaters. The heaters are primarily steam-heated radiators, through which the air of the buildings is circulated by electrically-driven fans. Our machine shop is located to the east of, but central to, the main operating buildings of the mine and plant, and is so connected by a net work of tracks as to be able to serve all portions of the entire plant conveniently. The building is divided into two bays, the main bay 53 ft. by 340 ft., and the east bay 24 ft. by 340 ft. The shop office and drafting room, a two-story annex 24 ft. by 30 ft., is located on the west side of the shop. The arrangement within the shop is such as to house conveniently the several departments, namely, heavy machine tool section, repair floor section, boiler shop heavy tool and floor section, blacksmith heavy tool and forge section, tool room, electric welding rooms, stock room, tin and copper shop, and electrical parts and armature winding and repair shop (see Figure 1). All the heavy tools, the repair floor section, and railway tracks are so located in the large open bay as to be fully serviced by an electrically operated 15-ton bridge crane, with a span of 50 feet and a travel the full length of the shop. A standard-gauge railway track, branched off the main line, penetrates the full depth of the building. This track lies along the extreme east side of the main bay, allowing easy entrance and movement of rolling stock and heavy machinery, loaded on standard flat-cars, to the repair floors in the main bay. Eight jib cranes, affixed to building columns, further facilitate the heavy repair work throughout the various shop divisions. Our light and heavy machine tools are standard equipment, not unlike tools used in mine, mill, and railway shops.

Jan 1, 1935

By M. K. Jain, Z. T. Xu, M. Bruhis, V. Hegedekatte

"Strain rate and temperature dependent deformation conditions are present during elevated temperature forming of aluminum and other metallic materials. While many constitutive laws have been proposed to represent such deformation conditions, a closer investigation often reveals their limited applicability in terms of fit to the experimental data, and interpolation within and extrapolation outside of the range of experimental stress-strain curves. This is often because material-specific primary deformation mechanisms of temperature-dependent strain and strain rate hardening are poorly captured. In the present work, the Voce-Kocks constitutive model based on mechanics of dislocations storage and annihilation has been found to be suitable for many metallic materials. The model was modified to include the effect of temperature dependent shear modulus. The modified model is then employed to represent the experimental data obtained from uniaxial tensile tests on AA7075-O sheet at elevated temperatures and strain rates. Also, hot gas bulging tests were conducted to verify the applicability of this model. Further, finite element simulation of the hot gas bulge test was performed by incorporating the model as a user material subroutine. Good general agreement was observed between the experimental and FE model predicted results. Some sources of discrepancy in the prediction are also discussed.INTRODUCTION There has been much interest in light-weighting of automobiles from automotive related industries to reduce overall carbon footprint and increase energy efficiency of the vehicles. Aluminum alloys, and especially the medium-strength 5xxx and 6xxx series alloys, have been the primary focus in the last 3 decades to reach the above environmental goals (Huo, Hou, Zhang, & Zhang, 2016) whereas aerospace industry has traditionally focused on high strength 7xxx series aluminum (Al-Zn-Mg-Cu) alloys for structural components (Deng, Yin, & Huang, 2011). Recently, there has been much interest in high strength 7xxx series aluminum as a replacement for heavier steel automotive structural parts such as A-pillar, B-pillar, side impact beams etc. (Harrison & Luckey, 2014). This is both interesting and challenging since the above aluminum structural parts will need to not only meet impact safety standards but also possess sufficient formability for manufacturing such complex parts. Since the formability of high strength 7xxx series materials is quite poor at room temperature, much interest has focused on improving both formability and final part strength via high rate hot stamping, in-die quenching, and subsequent artificial ageing process steps (Kumar & Ross, 2016)."

Jan 1, 2018

By G. D. Bateson

"The Low NOx/SOx (LNS) Burner is a technology which, in pilot-scale tests, significantly reduces acid rain-forming emissions from the burning of coal. The precursors of acid rain are nitrous oxides (NO) and sulphur dioxide (SO:;) . TransAlta is currently planning two demonstration projects.Esso Resources Canada and TransAlta are undertaking a project to demonstrate how coal can be burned cleanly for steam raising in heavy oil operations by using TransAlta&apos;s LNS Burner on a steam generator at Esso&apos;s Cold Lake Production Project. The $10.7 million project started up in mid-J990, with testing to be completed in mid-I99J. The province of Alberta and Western Economic Diversification Canada, along with other private industry, are contributing funding to the project.The other demonstration project that has been selected for funding under the United States Department of Energy&apos;s Innovative Clean Coal Technology Program is a retrofit of LNS Burners to a 33 MW cyclone unit at Southern Illinois Power Cooperative&apos;s Marion generating plant. The US$13.6 million project is scheduled for completion 18 months after final funding arrangements are made.TransAlta believes that these demonstrations will lead to the development of a commercial ""clean coal"" technology. Other demonstration projects being planned will further broaden the base of applications.IntroductionTransAlta has recognized an increasing concern worldwide for the environment, and in particular the acid rain problem. Increasing public concern and the need to meet either current or possibly more stringent emission regulations have prompted them to explore various emission reducing technologies - despite the low sulphur content of its coal.The flue gas desulphurization (FOD) and selective catalytic reduction (SCR) technology currently available to reduce sulphur and nitrous oxides from coal burning power plants is very costly. Having to incorporate FGD technology, or ""scrubbers"", greatly adds to the cost of producing power. Having to add such high costs to electric customers&apos; bills is something TransAlta is striving to avoid.There are many research programs now underway which are evaluating ways to provide electricity from coal in a clean manner. TransAlta has been observing or participating in a variety of these programs. However, there is one new technology which the company has identified as having the potential to control acid rain causing emissions at a fraction of the cost of conventional systems. That technology is called Low NOx/SOx, Burner - or LNS Burner."

Jan 1, 1990

"A method is described for determining the viability of hard rock orebody extraction by block caving. Using a very limited amount of geotechnical data, the procedure enhances Laubscher’s empirical stability graph method by using the complex structural modelling system (ChaSM) to assess cavability and block cave tonnages.IntroductionIn considering the selection of suitable mining methods, block caving has gained popularity over other extraction systems in recent years (Butcher, 1999). This has been ascribed to the fact that block caving is the lowest cost per ton mining method, with orebodies that were in the past considered unsuitable for caving, now being successfully mined. However, even though all orebodies will cave, a problem exists in the evaluation of economic viability — it is necessary to be able to predict both when the orebody will cave and what will be the sizes of the initial ore fragments (and the associated tonnages) that report to the drawpoints. This problem is compounded by the fact that, during the scoping study phase of a project, only limited geotechnical data may exist on which to base an assessment of whether block caving is viable or not. Empirical and numerical methods of cavability assessment do not account for the full effects of geological discontinuity trace lengths, nor for the stress regime. Those require significant geotechnical data to be available. The result is that uncertainty may exist as to whether block caving is an economic option. This uncertainty is complicated by the fact that limited experience exists with the caving of more competent orebodies.This paper describes a method for assessing cavability, and for predicting the size of initial ore fragments and the tonnages reporting to block cave drawpoints, using only the level of data normally available during a scoping study. Fragment size and tonnages are assessed by identifying potentially unstable blocks and wedges in the undercut back using statistical joint data. The effects of lateral confining stresses are accounted for by comparing the in situ stress orientations with the joint orientations. To evaluate the accuracy of the method, a back analysis exercise was conducted to predict cavability and initial tonnage for a mine in which the actual behaviour is known. The method is then applied to cavability and tonnage predictions for a hard rock orebody."

Jan 1, 2002

By A. M. A. Mohamed, F. H. Samuel, S. Alkahtani

"This article was undertaken to investigate the effect of nickel and zirconium additions on the strength of 354 aluminum cast alloy. The cast alloys were given a solutionizing treatment followed by artificial aging at 190 ºC for 2 hr. High temperature tensile tests were conducted at various temperatures from 25ºC to 300ºC. Optical microscopy and scanning electron microscopy were used to study the microstructure of the samples. The results revealed that the intermetallics phases of (Al,Si)3(Zr,Ti), Al3CuNi and Al9NiFe are the main feature in the microstructures of alloys with Zr and Ni additions. The results also indicated that the tensile strength of alloy decreases with an increase in temperature. The combined addition of 0.2 wt% Zr and 0.2 wt% Ni leads to a 30% increase in the tensile properties at 300ºC compared to the base alloy.INTRODUCTIONThe task of improving the mechanical properties in an aluminum alloy at high temperatures should include the knowledge of several factors which are related principally to a decrease in the strength of the metal with increasing temperatures. This behavior is linked to the change or deterioration in the principal metallurgical parameters of the specific cast aluminum alloy during its performance at higher temperatures. Most of applications of Al-Si casting alloys are generally used at temperatures of no more than 230°C (Lee & Chen, 2002). This recommendation is made in view of the fact that, for certain applications such as those required by the automotive industry, these alloys must operate over a wide range of temperatures and stress conditions where temperatures are liable to rise even higher than 230ºC (Robson & Pragnell, 2003).Aluminum-silicon-copper-magnesium alloys such as the 354 alloys show a greater response to heat treatment as a result of the presence of both Mg and Cu. These alloy types display excellent strength and hardness VALUES (although at some sacrifice of ductility and corrosion resistance. These alloys are used for a wide range of applications, such as engine cooling fans, crankcases, high speed rotating parts, structural aerospace components, air compressor pistons, fuel pumps, compressor cases, timing gears, rocker arms, machine parts, and so forth (Cáceres, Svensson, & Taylor, 2003; Rurrxia, Rong-de, Yu-hua, Cherrxi, Xiao-feng, Heng-rong, & H. Zhuang-qi, 2004)."

Jan 1, 2012

By Y. Thibault, L. Morin, R. Cameron, D. Gould

"There are an estimated 50 to 100 million dry metric tonnes of low-grade nickeliferous pyrrhotite tailings in the Sudbury area alone, with an average nickel grade ~0.8% (plus cobalt). Pyrrhotite is a highly reactive sulphide mineral that has the potential to generate acidity; consequently, it is stored in large tailings ponds that require perpetual treatment to avoid the production of acidic drainage. Re-processing this material using bioleaching technologies has the potential to recover valuable metals, while reducing the toxicity, reactivity, and acid generating potential of the remaining residues. CanmetMINING is currently developing a stirred-tank bioleaching process to recovery nickel and cobalt from pyrrhotite-rich tailings. Stirred-tank experiments have been conducted with one tailings sample over a range of pH and temperature conditions, resulting in 80 to 90% and 70 to 80% leaching of nickel and cobalt respectively in 10 days.INTRODUCTION Sulphide tailings may represent a significant financial liability for mining companies as these wastes may produce acidic drainage under some disposal conditions. As a result, the companies must post financial bonds large enough to ensure there are sufficient funds for perpetual management of these wastes. At the same time, there are billions of dollars in metals incorporated into these mining wastes waiting to become valorized. Many sulphide tailings are amendable to bacterial oxidation for metal extraction. Re-processing of tailings using bacterial leaching has the potential to recover valuable metals from waste; and reduce the toxicity, the reactivity, and the acid generating potential of the remaining residue. By reprocessing these wastes there is an opportunity to significantly reduce liabilities and financial assurance bonds, while recovering metal values. There are an estimated 50 to 100 million dry metric tonnes of low-grade nickeliferous pyrrhotite-rich tailings in the Sudbury area alone with an average nickel grade ~0.8% (Peek et al., 2011) plus cobalt and copper. Pyrrhotite is separated from pentlandite concentrates by magnetic separation and flotation. It is already finely ground and has often been segregated from other tailings material, making „mining? relatively inexpensive. This represents roughly (> $100/ton) in contained value, with negligible mining costs. This paper reports on the development of a stirred-tank bioleaching process for recovering nickel and cobalt from pyrrhoitite-rich tailings, which is currently underway at Canmet MINING."

Jan 1, 2017

By S. G. Luckey, N. R. Harrison, F. Nadeau, U. Brüx

"The adoption of tailored-rolled or tailor-welded blanks (i.e. TRB/TWB) in the automotive industry has been known to offer great potential for the optimization of weight, function, cost and complexity. Vehicle light weighting can further be achieved by using high strength aluminum alloys like the 7xxx-series. 7xxx-series alloys are capable of delivering specific strengths equal to or greater than high strength steels. However, room temperature formability of this aluminum class is limited, so one approach to forming 7xxx-series alloys is by hot stamping. Hot stamping utilizes an elevated temperature blank and the high pressure stamping contact of the forming die to simultaneously quench and form the sheet. This paper explores the initial feasibility of tailored thickness material for body-in-white applications when processed under hot stamping conditions.INTRODUCTION Steel tailor-rolled blanks (TRB) or tailor-welded blanks (TWB) have been used within the automotive industry as a method of reducing weight, expanding material utilization, and decreasing overall part/assembly cost (Ganeasan et al., 2015; Merklein et al., 2014; Hirt et al., 2005; Kridli et al., 2000). The production of such tailored thickness materials has resulted in over $2.5 billion (2016) in combined industry sales (Mubea, 2018). As automakers begin to adopt the manufacturing practices traditionally reserved for steel such as tailor rolling/welding with greater enthusiasm for vehicle light weighting, there exist an opportunity to expand the material database to extend beyond the traditional aluminum alloys found in current production. High strength aluminum alloys, i.e. 7xxx-series, are ideal for structural automotive applications due to their high specific strength; however, they have limited room temperature formability. Hot stamping, another manufacturing practice used by the steel industry, can be used to form these high strength materials. The combination of tailoring the thickness of a sheet material and hot stamping provides an opportunity for significant weight saving within an existing manufacturing footprint. This paper explores the potential and challenges of this approach when applied to structural body-in-white components. The methods for tailor rolling, tailor welding and hot stamping are described and applied to the production of a 7075 aluminum alloy B-pillar. The results are discussed in terms of feasibility and weight savings."

Jan 1, 2018