Search Documents

By A. M. Abdel-Rehim

The present work reports a study of production of thorium concentrate from Egyptian monazite by decomposition of ammonium carbonate solutions containing ammonium thorium and uranyl carbonate complexes. These solutions were obtained from the processing of monazite by alkaline leaching in ball-mill autoclaves, followed by selective separation of thorium and uranium from lanthanides by autoclave leaching of the hydroxide cake obtained with ammonium carbonate - bicarbonate solutions. The separation of thorium and uranium in the form of thorium concentrate from their carbonate complexes was achieved by different methods, including neutralization of solutions at pH = 6.7 by acid, addition of alkali at pH = 11.5, heating of solution at 100°C and processing of carbonate solution with steam under pressure in steel autoclaves. Processing of solutions of thorium and uranyl carbonate complexes in an autoclave with steam causes their decomposition. Complete recovery of thorium 99.8% and 98.4% uranium recovery in thorium concentrate was attained at 120°C and steam pressure 2 atm, within 10 min. Meanwhile, the recovery of lanthanides was low and did not exceed 1.1%. The thorium concentrate produced contains 67.82% Th, 4.6% U and 3.14% REE. All methods achieve complete separation of thorium and uranium from their carbonate solutions, but the first two methods are unfavourable for the industry due to the high cost of reagents and their inability to regenerate the ammonium carbonate. The decomposition of ammonium thorium and uranyl carbonate complexes with steam under pressure is recommended for industrial application for its simplicity and the ability to regenerate the ammonium carbonate.

Jan 1, 2004

By Megan Becker, Aubrey Mainza, Indigo Research Laboratories, Jenny Wiese, Gaynor Yorath, Lucy Little

Particle shape characterisation has an important role to play in mineral processing, to clarify effects of shape on rheology, equipment wear rates, comminution, classification, sizing and flotation. However in industry, shape characterisation is not routine, and the most commonly used shape descriptor in the field (circularity/ angularity/ sphericity) is not invariant. This study aims to investigate shape measurements for a fine particulate ore sample measured with different analytical devices. Two Automated Scanning Electron Microscopy devices with Energy Dispersive X-ray Spectrometry (FEI QEMSCAN® and Zeiss Mineralogic®), and a camera based image-sizer using dynamic image analysis (Retsch CAMSIZER® XT) were compared. Each device was used to analyse the shape characteristics of specific particles in both a coarse sample (–212/+150 µm) and a fine sample (-53 µm) of UG2 platinum ore. Circularity and Roundness frequency distributions obtained from the three devices were then compared. For selected individual particles, circularity showed higher variability than roundness, and the sample circularity distributions obtained by the three devices were completely different. It is clear that circularity data from different studies relying on different devices should not be compared on an absolute scale. The shape parameter roundness was found to be a more robust descriptor than circularity, and it can give a stronger indication of a particulate sample’s shape characteristics on an absolute scale. However, there were still significant differences in the roundness measurements obtained by the CAMSIZER XT and the two Auto-SEM devices, which was attributed to the dissimilar mechanisms of image capture.

Jan 1, 2016

By A. Warczok, T. A. Utigard

"Slags from smelting of copper concentrates contains from 1 to 15% of copper. Copper is present in the form of copper or copper matte inclusions of size from 2 to 1000 micro, and as dissolved cuprous oxide. Removal of the copper requires the slag reduction, primarily reduction of magnetite and co-reduction of cuprous oxide. Thus, the kinetics of the slag reduction play an important role in copper recovery. Instantaneously, at the contact of carbon and a slag the gaseous film is formed. The magnetite and cuprous oxide reduction is going through a gaseous film, separating the slag and carbon of a coke or electrodes. The thickness of a gaseous film grows to a critical value and gas bubbles, containing CO and CO2, are created and rise up in the slag. Results of measurements of kinetic of the slag reduction with graphite showed high value of activation energy, close to the value of activation energy of Boudouard reaction. Strong temperature dependence of the reaction rate points out the thermal instability of the reacting system. It was found that the slowest process in the reduction stages determines the loop of CO and CO2 transfer and magnetite diffusion to the slag/gas film boundary. Strongly endothermic Boudouard reaction seems to cause thermal instability on the reaction surface. So, heat transfer to the reaction surface is very important. Due to low thermal conductivity of a slag the convection dominates in the heat transfer. So, any slag stirring accelerates the rate of reduction and coalescence of metallic copper or copper matte inclusions."

Jan 1, 2015

By Frederick J. Browne

Water, water everywhere, but not a drop (fit) to drink! Trite, but how often only too true? What is there met with in mining which, under various circumstances, may be said to be the most sought-for and highly-prized and also the most objectionable and most feared? Water! What visions that combination of five letters brings to all thoughtful minds? Up to near the end of the eighteenth century water was thought lo be an element but was then discovered to be the result of the combustion of two volumes of hydrogen with one volume of oxygen, and water so produced is chemically pure. Pure water is a clear and colourless liquid when seen under ordinary conditions, but appears bluish when seen through a long tube, and this same bluish tint may be observed in many lakes, especially those of glacial origin. A story often told describes a prospector in the desert who, failing to find water to replenish his canteen, suffers torture and death under fearful circumstances. Then again we may recall the flooding of mines, where water poured in so quickly that there was no opportunity of saving the unfortunate workmen. Instances might be multiplied without number showing that either the lack or excess of this essential fluid has taken heavy toll of human life. In all branches of mining and associated industries water must be dealt with to a larger extent, from an economic point of view, than any other substance, and very often the purity of the water is a matter of considerable importance.

Jan 1, 1925

By G. F. Round

In order to obtain values of angle of shearing resistance and initial resistance for McMurray oil sand for use in general design calculations, the shear strength of this oil sand was measured in a controlled strain type tester, modified so that the rate of deformation could be varied between 0.01725 and 0.1869 inches per minute. Effect of temperature was investigated by adapting the equipment to operate at both 71 ° and 185 °F. The data are reported in terms of angle of shearing resistance and initial resistance for varying rates of deformation, composition and temperature. While the main sets of results reported here were obtained at a bulk density range of 108.7- 109.5 lb. / cu. ft., some results were obtained at a bulk density range of 101-102 lb. / cu. ft. Analysis of varance tables have been drawn up from the results obtained from least squares correlations and significance tests applied. It was concluded that oil content and temperature were significant variables for the degree of shear strength developed by the oil sand; increase of oil content and decrease of temperature each cause an increase in shear strength. The bulk density range 108.7 to 109.5 lb./cu. ft. gave angles of shearing resistance from 30° to 40° and initial resistance values of 0.37 p.s.i. to 0.85 p.s.i. For the bulk density range 101 to 102 lb. / cu. ft., lower values of shear strength were obtained, indicating that compaction density was also of importance

Jan 1, 1960

By Keith Haddock

"The Sheerness Mine, a new surface coal mine located near Hanna, Alberta, went into full production in mid-1995. The mine, which is operated by Luscar’s subsidiary Forestburg Collieries (1984) Ltd., has the design capacity to supply up to 2.1 million tonnes of sub-bituminous coal per year to the adjacent Sheerness Generating station under a 30-year contract. This paper documents the construction phase of this project and highlights the major equipment purchases as well as the construction of the mine facilities. The paper also focuses on some of the areas where cost savings have been achieved that have allowed the mine to come on stream six months ahead of schedule, and under budget. Project ReviewMine DescriptionThe Sheerness Mine is located 25 km southeast of the town of Hanna in southeastern Alberta (Fig. 1). The mining property occupies the western portion of the Sheerness CoalField and borders the Montgomery Mine, operated by Manalta Coal Ltd. in the east, and Highway 36 in the west. The Montgomery Mine and the Sheerness Mine exclusively supply the total coal requirement of the adjacent Sheerness Generating Station. The station is owned jointly by Alberta Power Limited (APL) and TransAlta Utilities Corporation (TAU). APL is the operator. Manalta’s Montgomery Mine has supplied coal to the Sheerness Station since its opening in 1986. Coal is shipped by truck from the mines over a network of haul roads to the coal receiving hoppers located on the east side of Highway 36."

Jan 1, 1997

By Fathi Habashi, Ahmet Deniz Bas

"The mechanism of leaching of semiconducting minerals such as PbS, ZnS, UO2, etc., has been the subject of intensive speculation by hydrometallurgy researchers in the early 1950s who assumed the formation of intermediate surface complexes that could be neither separated nor identified by physicochemical techniques. The electrochemical theory of leaching introduced in the late 1960s resolved this problem by comparing the leaching process to a corrosion phenomenon similar to the corrosion of metals. Few years later, experimental evidence showed that anodic and cathodic zones are formed on the dissolving mineral although no electric current is imposed on the mineral during dissolution. A discussion of these findings is outlined.INTRODUCTIONIn the early 1950s researchers realized that kinetic studies for leaching ores are as important as thermodynamic calculations. It was also during this period that the concept of species adsorption on mineral surfaces has dominated the interpretation of the mechanisms of most reactions. This may have been due to the fact that many researchers of this period came from the mineral dressing sector and were influenced by flotation theories. However, when the knowledge of lattice defects and the semiconductivity of minerals became known and their importance in extractive metallurgy was realized, there was a need to explain the leaching reactions in light of these modern theories (Habashi, 1969, 1970). Semiconducting minerals of importance in metallurgy are two categories: the sulfides such as those of copper, lead, zinc, and the oxides such as those of uranium."

Jan 1, 2016

By H. A. Pearse

Introduction This paper may be regarded as another instalment of the story of the Britannia milling operation. From time to time in the past, articles (1) have been prepared by various members of the staff, giving details of crushing, grinding, and flotation treatment for the normal Britannia ore. It is not, therefore, the purpose of the present paper further to discuss what may be termed the standard milling operation, but rather to describe a flotation practice which has been evolved directly as a result of the general depression. The normal Britannia ore mixture contains chalcopyrite and pyrite as the main sulphide minerals, together with minor gold and silver values. The standard milling practice, evolved during several years of experimentation, provided for bulk flotation of the two sulphides after primary grinding to only approximately 35-mesh, followed by regrinding of the bulk concentrate, with subsequent separation of the chalcopyrite and pyrite to make a marketable concentrate of each mineral. However, in the face of a constantly increasing surplus of copper on the world markets and a steadily falling price during 1930 and 1931, it was obviously undesirable to continue producing large quantities of this metal at a loss. On the other hand, Company officials were very reluctant to add to unemployment by closing down entirely, provided operations could be continued without excessive losses. Fortunately, the existence was known of a fair sized body of ore, quite low in copper and relatively high in zinc content, with also a very considerably higher gold value than that prevailing in other sections of the mine.

Jan 1, 1934

By D. Karpoff

"IntroductionUNTIL the recent discovery and development of deposits at Allard Lake, on the Lower Romaine river, practically the whole of Quebec's - and indeed of Canada's - production of ilmenite had come from deposits in the vicinity of St. Urbain, Charlevoix •county, a village about eight miles north of Bay St. Paul on the north shore of the St. Lawrence, some sixty miles below the city of Quebec (see Figure l) . Although these deposits were known nearly three hundred years ago and were worked in a small way during the years 1872-74, when a charcoal blast furnace was operated by the Canadian Titanic Iron Company for making white pig iron, it was not until 1908 that more or less continuous production commenced and has •continued to the present by the American Titanic Iron Company. The whole of the output has been exported to the United States.The ilmenite occurs in lenses •and dyke-like bodies within anorthosite. Production has come chiefly from three deposits: General Electric, Furnace, and East and West Coulombe. During 1951 -52, an extensive diamond drilling programme was carded out under the direction of the writer to test the Furnace and the East and West Coulombe deposits (Figures 2 and 3), which form part of the property of St. Lawrence Iron and Titanium Mines, Limited. The average tenor of the orebodies encountered in the course of the drilling was 38.60 per cent TiO2 and, in addition to these high-grade •bodies, there was found a very considerable tonnage of lower grade ore."

Jan 1, 1953

By F. J. Hrach, K. P. Flynn, P. J. Miranda

"ST Equipment & Technology, LLC (STET) has developed a processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the triboelectric belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) particles with very high throughput. The high efficiency multi-stage separation through internal charging/recharging and recycle results in far superior separations that can be achieved with a conventional single-stage free-fall tribo-electrostatic separator. The triboelectric belt separator technology has been used to separate a wide range of materials including mixtures of glassy aluminosilicates/carbon, calcite/quartz, talc/magnesite, and barite/quartz. Separation results are presented for selected industrial mineral sources. An economic comparison of using the tribo-electrostatic belt separation versus conventional flotation for barite / quartz separation illustrates the advantages of dry processing for minerals.INTRODUCTIONThe lack of access to fresh water is becoming a major factor affecting the feasibility of mining projects around the world. According to Hubert Fleming, former global director for Hatch Water, “Of all the mining projects in the world that have either been stopped or slowed down over the past year, it has been, in almost 100% of the cases, a result of water, either directly or indirectly” (Blin et al., 2013). Dry mineral processing methods offer a solution to this looming problem."

Jan 1, 2016

By A. G. Scobie

THE research laboratory of this Company was recently faced with the problem of determining trace amounts of tungsten in a series of classifier sands. A spectrographie survey revealed the feasibility of using this instrument in the final evaluation, but a check of the common methods in use for the isolation of tungsten (3, 4) showed these methods to give incomplete separation for trace amounts. An investigation into the possibility of modifying these procedures, or developing others, was thus indicated. ASSAY PROCEDURE Weigh 10 grams of 200-mesh ore or concentrate into a 400-ml. beaker, wet the sample well with about 20 ml. of water, and add 100 ml. of hydrochloric acid. Cover, digest at 60° to 70° C. for about 1 hour, and then boil down to approximately 25 ml. Cool, add 25 ml. of hydrochloric acid and 10 ml. of nitric acid, and again boil to former volume. Add 20-ml. portions of nitric acid with successive boiling clown until chemical action is complete. Then add 20-ml. portions of hydrochloric acid until all nitric acid is removed. Take nearly to dryness on a law-temperature hot plate, but do not bake. Take up in 10 ml. of hydrochloric acid and 20 ml. of water and heat on a law-temperature hot plate until all iron goes into solution. Dilute to 200 ml. and heat to just below boiling. Stir in pulp of about half of a No. 41 Whatman filter paper (12.5-cm.) and continue digestion on plate with occasional stirring for 15 to 20 minutes.

Jan 1, 1943

By H. Kuno, H. Kobayakawa

A borehole inclinometer with FBG optical fiber sensors has been developed to clarify very slow slope movements, and the results of its application to a real slope have been shown. The main characteristics kept in mind while developing this inclinometer are as follows. Firstly, the workability must be good so that only one cable is required for taking the measurements, because the inclinometer is composed of several FBG sensor elements constructed on an optical fiber. Secondly, the minimum interval of the distorted measurements must be close, namely, within 100 mm. Thirdly, the inclinometer must excel in thunder resistance. The measurements were executed by setting up the developed borehole inclinometer on a slope where the rate of displacement is several millimeters per year. The movement of the device was developed by comparing it with that of the results of an existing borehole inclinometer. The area of the displacement concentration, 1 m in width for 4-m sections, was confirmed by the existing borehole inclinometer. The boring core, recovered using a high-quality drilling technique, was examined. Landslide clay was not permitted at the location where the displacement had concentrated as a result of comparing the measurement results with the boring core, and the rotation of gravel by the movement of the slope’s land block was allowed. These results show the slope being caught in the stage just before a primary landslide. In addition, the feature whereby the slope behavior depends on the depth was analyzed by comparing the information on the underground displacement with precipitation and earthquake records.

Jan 1, 2015

By J. Keith Haddock

"Introduction The Boundary Dam Mine is located 5 km south of the City of Estevan, Saskatchewan and is operated by Manitoba and Saskatchewan Coal Company Ltd., one of the Luscar companies. The entire production of 1.7 million tonnes per year is delivered to the Boundary Dam Generating Station of Saskatchewan Power Corporation. Geology There are basically two seams mined on the property, the main Estevan seam ranging in thickness from 3.0 m to 4.5 m with partings and the upper Roche Percee seam (roughly 15 m to 23 m above the Estevan) which ranges from 0.6 m to 2.0 m in thickness. Most of the reserves are concentrated in the Estevan seam, the Roche Percee only being mined whenever its thickness makes it economic to recover. The coal measures belong to the Ravenscrag Formation of Tertiary (Paleocene) Age. This formation is widespread in North Dakota and Montana and contains the lignite fields of North Dakota and subbituminous coals of Montana. The formation is gently tilted to the southeast at Boundary (0.5 degrees) and consists of weak sandstones, siltstones and silty mudstones. Reserves and Coal Quality The present minesite encompasses a coal reserve of approximately 50 million tonnes calculated to a maximum stripping depth of 37 metres or 20:1 mining ratio. The reserves form only a part of the total reserves in the Estevan area which are owned by the Saskatchewan Power Corporation. The coal being mined is classed as Lignite ""A"" and has the following specifications:"

Jan 1, 1985

By M. Mononen, J. Huuskonen, M. Vauhkonen, J. Kourunen, A. Lehikoinen

"A new approach to measure process conditions in flotation cells is presented. Real scale flotation cells in a Zinc circuit are imaged using Outotec LevelSense sensors based on electrical resistance tomography. The latest results from long period plant tests show that the sensors together with FrothControl analysis give new information that correlates well with other process parameters. The sensors can compensate for electrical contact contamination using an automatic calibration technique and they are basically maintenance free. The results indicate that using the LevelSense sensors and FrothControl solution, the process control and optimization can be done automatically, stabilizing and improving the metallurgical performance of the flotation process.INTRODUCTIONThe froth flotation process is widely used in mineral industry for the separation of minerals from low-grade ore slurry. Different property parameters of froth and slurry could be measured to monitor and control the flotation process: air bubble size distribution, flow dynamics, thickness of the froth bed, amount of solids in the froth, etc. Some techniques already exist that can be utilized in studying these important parameters on-line. Examples of the techniques are the high-speed video imaging, simple conductivity probes, ultrasound techniques, floats and pressure transducers (Maldonado et al., 2008). These techniques, however, often suffer from some limitations. For example, the video imaging only gives information from the surface of the froth, simple conductivity probes suffer from contamination and the floats may get stuck and therefore do not give reliable signal for process control and optimization."

Jan 1, 2013

By Walter K. (Cory) Conrad

Two pumping tests in the Chilson Member of the lower Lakota Formation were completed at nearly the same location in 1979 and 2008. The 1979 test consisted of a pumping well and several surrounding observation wells penetrating the full 55-m thickness of the aquifer. The 2008 test consisted of a pumping well and three surrounding observation wells screened over 10 m in one of the known uranium ore horizons in the lower portion of the Lakota penetrated only about 3 meters of the more than 55-m thick lower Lakota aquifer. The average transmissivity and storativity values determined from the 1979 tests were 17.6 m2/day and 1.8 x 10-4, respectively. Comparing median transmissivity of 13.9 m2/day and storativity of 1.2 x 10-4 determined in the 2008 test to the 1979 test, the new aquifer parameters for the lower Lakota are respectively about 80 and 70 percent of the 1979 results. Because transmissivity and storativity depend on aquifer thickness, comparing the results suggests that there may be some scaling effect between the tests due to the differing lengths of screened intervals. However, the effect cannot be predicted by calculations such as relative screen lengths or open intervals to the formation, or sandstone versus shale thicknesses on geophysical logs. The scaling effect is attributed to partial disconnection between the lower and upper portions of the Lakota Formation aquifer by locally continuous shale interbeds. Suggestions to resolve this scaling issue are presented.

Aug 1, 2010

By Scott G. Honan, Wayne F. Luinstra

"Since 1992, the concentration of gold using gravity methods has progressed to become an important part of production at Hemlo Gold's Golden Giant Mine. Currently, the gravity circuit accounts for approximately 25% of the Golden Giant Mine's Gold production. This circuit consists of a 30 inch Center-Drain Knelson Concentrator and a Shaking Table. The evolution of gravity concentration will be discussed with an emphasis on the economic justification for a gravity circuit as well as the practical aspects and metallurgical impact of operating such a circuit. It will be demonstrated that the operation of a gravity circuit has definite benefits to the operation of the Golden Giant Mill and will continue to play an important role in future gold production.1.0 IntroductionHemlo Gold Mines Inc. Golden Giant Mine is a 3000 TPD underground gold mine and milling facility located 40 km east of Marathon, Ontario. Mining is accomplished by means of sublevel longhole open stoping. The ore is processed using conventional crushing, 3-stage ball milling, conventional cyanidation and CIP processes. The mill and concentrator are described in more detail in other publications1,2.Since July of 1992, the Golden Giant Mine has been using a gravity circuit for gold recovery in the mill's grinding circuit. Despite the fact that gold recovery averages over 96% using conventional cyanidation and carbon-in-pulp processes, the gravity circuit has become an integral part of milling operations. This paper will discuss the economic justification for a gravity circuit as well as the practical and metallurgical aspects of its operation."

Jan 1, 1996

By Emmanuel Henry

Few industries are more challenged by technical, political and market uncertainty than the mineral industry. Technical uncertainty in mining projects concerns the volume and quality of the resource, the processing and metallurgical parameters, the production efficiency, etc. Political uncertainty can take diverse forms and includes possibilities of change in the taxation system, risk of expropriation and risk of social instability or war. Market uncertainty depends on the market structure of the commodity; price and demand volatilities are the most common sources of market uncertainty. Intensive feasibility studies including these uncertainties and risks are required before investing up to billions of dollars in the development of a new mine. Current feasibility studies are often based on a single (or very few) mean geological scenario and simplified price profiles along the life of the project. Yet, strategic decisions, for example, the level of investment in exploration and metallurgical studies, adoption of a flexible, but more costly, mine design and risk-sharing strategies are made at an early stage. Over the last twenty years, Real Option theory has emerged as a unifying framework enabling strategic planning under uncertainty (technical, political and market). Geological and market variances (second order statistics) are pivotal for proper uncertainty quantification. The present study explores the possible benefits of combining modern geostatistical tools and financial techniques for project management. More precisely, the following questions are examined: Is geological uncertainty really an issue? Can we combine geological and price uncertainties in a unifying Real Option framework? A simple example aimed at illustrating the concepts involved is presented.

May 1, 2003

By Göckmann. Klau

"IntroductionCopper has been recycled ever since its discovery. Even in Graeco-Roman times recycling of this resistant, and thus valuable material was carried out as a matter of course. Just take, as an early example, the Colossus of Rhodes: after the figure collapsed during an earthquake, the bronze parts were melted down into ingots and sold.Copper is a material which can be recycled again and again because copper produced from recycling is not different from copper originating from primary materials. This is mainly due to electrolytical copper refining whereby not only the base metals but also the precious metals can be removed. In contrast, with aluminum and iron only the more electropositive elements can be removed by refining, and the resultant scrap must, therefore, be sorted mechanically into various alloys for subsequent smelting.The recycling rate for different base metals is given in Table 1. Despite this ideal prerequisite, the generally quoted recycling rate of copper of about 40070 appears rather low. However, it must not be forgotten that the recycling rate is defined as the ratio of the annually utilized quantities of copper scrap and the annual production figures (Table 2). Moreover due to the economic growth over the last 30 years the availability of copper from scrap materials is lower than its consumption because copper is principally employed in very long-life consumer durables and only returns to the recycling circuit after many years. The average time for the copper of some goods to be recycled is detailed in Figure 1."

Jan 1, 1992

By F. J. Munn

"Since 1976, Cardinal River Coal s Ltd. has completed mining in eight pits. In each of these pits, at least one wall has failed, none by design, although not totally unexpected, yet there was no loss of production nor risk to personnel or equipment. Cardinal River Coals Ltd. has been successful in implementing a program to cope with failures and now feels justified in adopting more optimistic design parameters.The wall control program at Cardinal River Coals Ltd. is based on the premise that the walls are going to fail, monitoring is to confirm when. The program consists of monitoring slope movements and piezometric levels as well as structural mapping and visual inspections. In case of excessive movement, the frequency and intensity of the monitoring is increased. If a failure is impending, suitable remedial action is undertaken such as cutting down the crest, building up the toe, depressurization of the wall, artificial support, or a combination of the above. If remedial action is not possible, monitoring permits operations to continue up to near the time of failure.At the design stage, the emphasis is on identifying the potential failure mechanisms and the con sequences of failure. Once the potential failure mechanisms are identified, a monitoring system can usually be employed to give sufficient response time, and providing the consequence of failure is not severe and/ or remedial action can be taken to arrest the movements, then it is practical to mine pit slope s which have a higher probability of failure."

Jan 1, 1985

By Helen Francis

Over the last decade, lower ore grades and deeper mine environments have demanded that mining companies develop new technologies (tools and processes) to ensure a mine?s economic sustainability. At Inco Ltd., this demand has lead to the focus of technological development within the area of automation. Delineation (Drilling and Interpretation) is a key step in the determination of ore grade and location and therefore was chosen as a priority area for enhancement through automation. Focusing on the tools (the diamond drill) automation, significant benefits have been consistently achieved in terms of productivity, process efficiency, operational safety, cost reduction, component life cycles and machine reliability. It is suggested that optimum benefits have yet to be achieved, and will not be achieved until the human aspects of automation have been properly addressed. Since project inception, the human aspects of automation were recognized as critical to the success of the diamond drill automation project. However, it was only upon the installation of the Automated Diamond Drill in the field and its continued use on a daily basis that this issue received due attention. The human aspects of automation can be broadly addressed as economic, physical and psychological. This paper, with examples from the field, will discuss the human aspects of automation in each of these areas. The paper will draw from observations and experiences acquired throughout this project and recommend implementation strategies that should be utilized in future automation projects to enhance both the acceptance of automation and the success of the automated process itself.

May 1, 2002