Search Documents

By D. F. Cooper, J. G. Paterson, K. H. Pang

"Effective control of metallurgy by manual adjustment of cell levels is common flotation practice. With an on-stream XRF analyzer interfaced to a process control computer it is possible to program the computer to carry out this function automatically. This paper describes the development and implementation of closed loop control of the concentrate and tailing grades at the Clarabelle Mill of the International Nickel Company of Canada, Limited, The XRF analyzer was used as the sensor, cell level as the control and the computer as the controller.IntroductionThe International Nickel Company of Canada, Limited recently brought on-stream Clarabelle Mill having a rated capacity of 35,000 tons per day. The plant was required to increase milling capacity in the Sudbury area by 9,000 tons per day and to improve milling efficiencies by replacing the obsolete crushing and grinding equipment at the Copper Cliff Mill. This represents the fourth mill built since 1959 and incorporates the latest thinking in a continuing evolution of instrumentation and control concepts. Table 1 illustrates control progress at Inco since 1959.In 1967 Frood-Stobie Mill came on-stream incorporating a central control room, an on-stream analyzer, a data gathering computer, and a significant change in instrumentation from direct-contacted pneumatic to miniature electronic. The computer successfully controls the analyzer but has very limited process control capability. Based on this experience a process control computer system was installed at Clarabelle Mill with the objective of carrying out extensive supervisory control and a limited amount of direct digital control."

Jan 1, 1973

By N. Maleki

In recent years, research and development of magnesium alloys have been greatly promoted by the lightweight requirements in critical industries. The use of these alloys, however, has been restricted by their limited mechanical properties especially at high temperatures. The disadvantages can be overcome by producing Mg matrix composites. The Mg?Si alloys containing in situ Mg2Si particles have found a great potential as structural materials. Unfortunately, Mg2Si compounds are prone to form undesirable coarse Chinese script morphologies, which would deteriorate the properties of the materials. Refinement of microstructure is performed for improvement of wear and corrosion resistance. This paper investigates the microstructure and corrosion behavior of pure magnesium, unmodified and modified magnesium matrix composites reinforced with Mg2Si particles. The Mg2Si/Mg composite was prepared via a normal cast route, and then various amount of zinc was added to melt in order to modify the Mg2Si reinforcement particle morphologies. The microstrucrures were characterized by optical and scanning electron microscopy followed by EDX analysis. The corrosion behavior of Mg/Mg2Si composite was investigated by using potentiodynamic polarization measurements. The results showed that by addition of zinc, the average size of the primary Mg2Si became significantly decreased from about 100µm to about 20µm, as well as its morphology changed from dendritic to a polyhedral shape. However, by adding extra amount of zinc many primary Mg2Si particles become coarse again. It was also found proper amount Zn addition increased the corrosion resistance of Mg/Mg2Si composite.

Oct 1, 2011

By O. Neves, C. G. González Beca, M. C. Sol Pereira, H. Sousa Vale, R. A. Guedes de Carvalho, M. N. Sampaio

"As sulphide ores are usually concentrated by flotation , the material is very finely ground <37um), wet and impregnated with the chemicals used in flotation. These conditions are favourable to the development ofchemical reactions which are largely influenced by atmospheric conditions (temperature, humidity, wind, etc.) as well as by the geometry of the piles.Physical and chemical properties of a chalcopyrite concentrate were determined by laboratory tests. The knowledge of these properties was considered necessary in order to establish a correct design of the storage and handling operations of the sulphide ore concentrates obtained by flotation.The properties studied in this work were: transportable moisture limit, flowability, effects of vibration, hygroscopicity, ""caking"", chemical alterations by humidity, oxidation and self-heating (auto-ignition, dry and wet oxidation, self-heating by humidification and its prevention).INTRODUCTIONIn order that the handling and the transport of a powdered material may be carried out correctly, it is necessary to know certain physico-chemical characteristics. Transportable moisture limit (TML), apparent density (both aerated and compacted), compressibility, angle of repose, angle of spatula, cohesion and angle of slide(l-4) are characteristics (among the flowability parameters) worth knowing.Moisture content of the powdered material is fundamental, because if this is too low heavy losses will occur when the product&apos;s particle size is very small, if it is too high, separations between solid and liquid phases may occur. In the latter case, the centre of gravity of the system may change suddenly and cause accidents, mainly if transport is by sea or by river."

Jan 1, 1989

By E. Tulcanaza

Mining companies normally establish exploration and research programs originated with actions in embryonic stage. At their early stages of development, these exploration and technological activities are subject to uncertainties that need, first, to be resolved, deciphered or, at least, mitigated for information reporting; and later, for valuation reporting. Under these circumstances, these exploration activities follow a sequence of development phases that range from exploration work to the profile, conceptual, and finally to basic engineering phases and construction. For information reporting, the International Template for Reporting of Exploration Results, Mineral Resources and Mineral Reserves integrates the minimum standards being adopted by the relevant professional bodies in Australia, Canada, South Africa, Chile, USA, UK, Ireland, and other European countries which set up the Committee for Mineral Reserves International Reporting Standards (CRIRSCO, www.crirsco.com). These standards are based on the progressive collection of relevant information to reduce present and future uncertainties over time under a context of transparency, materiality, and technical competence. For valuation reporting several procedures have been disclosed and applied. However, in the last decades financial instruments such as real options, decision analysis, and games theory have developed into a niche of great potential for mine valuation applications. The objective of this paper is to provide a summary of the information reporting standards prepared by the Chilean National Commission for the Qualification of Competent Persons in Mineral Resources and Mineral Reserves and show a procedure and an application of real options to the valuation of the sequential development phases of a mine asset from the exploration stage through up to full development.

Jan 1, 2007

By Simon C. Dominy, Patrick R. Stephenson, Alwyn E. Annels

Abstract - The often complex, erratic, and localized nature of gold is a common feature of many vein-style gold deposits. This style of mineralization is often referred to as being nuggety or possessing a high-nugget effect. As a result of these complexities resource estimation is difficult and in general, only Exploration Results can be provided or an Inferred Mineral Resource estimated from surface drilling data alone. Underground development, further drilling, and probably bulk sampling will be required to delineate Indicated and Measured Resources. Tonnages can generally be estimated from diamond drill and development information with a reasonable degree of confidence. Grade is much more difficult to define with confidence because it is commonly highly erratic and discontinuous in nature. The dependency of higher confidence Resource categories on development information may create a Catch 22 situation, with funding for such development often depending on the prior definition of at least Indicated Resources. There are no easy solutions to these challenges posed by high-nugget effect deposits, and it is important when classifying and reporting not to downplay the uncertainties often associated with Mineral Resource and Ore Reserve estimates for such deposits. However, in common with all deposit types, if the principles that underpin the estimation, classification, and reporting procedures are borne in mind and common sense applied, most issues can be satisfactorily resolved. This paper discusses the classification and reporting of Mineral Resources for high-nugget effect gold vein deposits within the framework of the JORC Code (JORC, 1999).

Jan 1, 2001

By Donald Leroux, Robert Grant

"Flotation is a complex and highly multivariate process. Using the conventional OFf (one-factor-at-a-time) technique, the optimization of flotation circuits through laboratory or plant testwork is difficult, time-consuming and therefore, expensive and often results in marginal improvements. The optimal operating conditions can be more efficiently estimated when a systematic approach like SDE (Statistical Design of Experiments) is taken.The concentrator of Noranda's Brunswick Mining Division (near Bathurst, New-Brunswick) is well known for the complexity of its differential copper-lead-zinc flotation circuits. One of them, the chalcopyrite-galena separation (or CuSep) circuit, is impacted by more than 20 variables.Statistical Design of Experiments (SDE) techniques were applied at the laboratory scale to improve the performance of Brunswick's CuSep circuit. Screening tests were conducted using Fractional Factorial designs while optimization tests were carried out based on Response Surface Modelling techniques like the Central Composite design. Every series of tests, without exception, revealed new information and process insights which led to significant circuit performance improvements in the plant So far, the metallurgical gain may be as high as four percentage points of copper recovery (in the CuSep circuit). Potential cost savings of expensive consumables (steam, activated carbon) have also been identified but will require additional circuit modifications before being realized.IntroductionIn spite of its apparent simplicity, flotation is a complex three-phase (solid, liquid and gas) separation process. Fundamentally, it is a highly multivariate process. Industrial flotation circuits are commonly affected by 10 or more process variables."

Jan 1, 1997

By John F. Vynne

This paper will discuss several of the systems and processes that have been developed over the past few years, and are now being utilized by major mining companies on draglines in North America, Australia and South Africa. These technologies include production monitors and reporting systems, GPS navigation systems, structural integrity monitoring systems, structural analysis studies to increase the dragline RSLs, and inspection and response strategies. The use of these technologies provides significant increases in dragline production, and reduces maintenance costs and downtime. The question that needs to be asked is what value is there in monitoring? Increasing dragline productivity is dependent upon to two items with the overall goal being to maximize the number of bank cubic meters moved and to uncover more coal: 1) maximizing payload and 2) maximizing the number of cycles. If you do not measure and try to optimize the parameters that impact payload and number of cycles, there is very little chance that you can improve overall dragline productivity. These parameters are: Maximizing payload is dependent upon the following: ? Geology ? Blasting ? Monitor weighing accuracy ? Engage location ? Disengage Location ? Rigging ? Suspended load ? Bucket characteristics ? Operator skills ? Minimizing rehandle Maximizing the number of cycles depends upon maximizing digging time, and minimizing cycle and delay/down times by: ? Minimizing Operational Delays ? Minimizing Mechanical Delays ? Minimizing Idle time ? Minimizing Walking time ? Minimizing Fill Time ? Minimizing Swing Angle ? Maximizing Swing & Return Rates ? Minimizing Spot Time A third reason to monitor, conduct structural analysis studies, and have inspection strategies is to prevent catastrophic failures such as shown in the following photographs (figures 1 & 2).

May 1, 2008

By W. Yang, R. Rajasingam, B. Tadesse, K. Mohanarangam

Copper electrowinning is a complex electrochemical process that involves the production of LME grade copper from copper rich electrolyte. The process involves the deposition of the copper ions onto the cathode from copper rich electrolyte with the production of oxygen bubbles at the anode. Acid mist is produced by these oxygen bubbles bursting at the electrolyte free surface. It is an undesired by-product of the Electrowinning process which unchecked could result in mist generation higher than the recommended time-weight-average exposure limit. Various approaches to alleviate the problem have been adopted by companies, all with varying degrees of success. All of these have been attempts to treat the symptom acid mist rather than the inherent problem, often proving expensive and, in some cases, ineffectual. In this paper, a new method was developed for acid mist quantification based on ‘total acid mist’ capture above the EW cell under well controlled conditions. With the use of sophisticated diagnostic analytical tools and measurement techniques it was possible to study all the operating variables including current density, flow rate, temperature, etc. independently and their effect on bubble size, bubble velocity, gas hold-up as well as acid mist generation and its droplet size. Results show that total acid mist capture increases with an increase in current density but remains more or less constant between 300–500 A m-2. Total acid mist also shows an increase with increasing electrolyte temperature. These findings are substantiated with the aid of bubble size and gas hold-up measurements with the transparent EW cell.

Jan 1, 2019

By M. Tsesarsky, M. Hazan, E. Gal

"Rock masses comprised of stiff inclusions in softer matrix are common in various geological environments. The heterogeneity and multi-scale nature of these materials make the evaluation of their mechanical properties a challenging task, which cannot be accomplished using conventional laboratory tests and composite mixture rules. We employ the homogenization method to estimate the mechanical properties of geological materials with inclusions. The homogenization method solves the equations of elasticity on the material (microscopic) scale for a unit cell subjected to unit strains under periodic boundary condition. The micro-scale elasticity equations are solved using the Finite Elements Method, and are in turn used to obtain the structure scale (macroscopic) material matrix.In this research, Finite Element models for unit cells with spherical and ellipsoidal inclusions were developed. Using the unit cells, a parametric study of the geometrical and statistical microscopic properties of the material composites was performed. The following parameters were studied: volumetric ratio, Young’s modulus ratio, size-distribution of inclusion and inclination angle of inclusions. The main purpose of the parametric study was to study the deviation from isotropy as a function of the aforementioned parameters.It was found that for volumetric ratio of 5%-40%, the deviation from isotropy increases, as the volumetric ratio of inclusions increases. For spherical inclusions, most of the cases studied exhibit quasiisotropic behaviour; whereas ellipsoidal inclusions exhibit considerable deviation from isotropy. The inclination of the ellipsoidal inclusions enlarges the deviation from isotropy (9% at random orientation and 26% at 0°)."

Jan 1, 2015

By J. H. Reiss, D. F. Bruhn, Idaho National Laboratory, Y. Jiao, D. W. Reed, Y. Fujita, D. L. Daubaras

"Bioleaching offers a potential approach for recovery of rare earth elements (REE) from recyclable materials, such as fluorescent lamp phosphors or degraded industrial catalysts. Microorganisms were enriched from REE-containing ores and recyclable materials with the goal of identifying strains capable of extracting REE from solid materials. Over 100 heterotrophic microorganisms were isolated and screened for their ability to produce organic acids capable of leaching REE. The ten most promising isolates were most closely related to Pseudomonas, Acinetobacter and Talaromyces. Of the acids produced, gluconic acid appeared to be the most effective at leaching REE (yttrium, lanthanum, cerium, europium, and terbium) from retorted phosphor powders (RPP), fluidized cracking catalyst (FCC), and europium-doped yttrium oxide (YOEu). The Acinetobacter isolate, BH1, was the most capable strain and able to leach 33% of the total REE content from the FCC material. These results support the continuing evaluation of gluconic acid-producing microbes for large-scale REE recovery from recyclable materials.INTRODUCTIONAn enhanced recovery, substitute, reuse or recycle paradigm is important for balancing the supply and demand of critical materials (DOE, 2011). The recovery of rare earth elements (REE) from recyclable materials is an important component in this model. REE are used in a variety of modern products. For example, neodymium, europium, terbium, dysprosium, and yttrium are important for applications such as permanent magnets, lamp phosphors, rechargeable batteries, etc. (Binnemans, Jones, Blanpain, Van Gerven, Yang, Walton, & Buchert, 2013; DOE, 2011; Graedel, Harper, Nassar, & Reck, 2013). Cerium and lanthanum are used in glass polishers and additives in fluidized cracking catalysts (FCC)."

Jan 1, 2016

By R. Esteban, D. Runnels, S. Girgin, J. Torrealba-Vargas

"Each mineral processing project requires early testwork to evaluate the economic potential of a deposit. The testwork needs to be efficient and it should provide enough information to obtain key parameters, first for a high level flowsheet selection at the conceptual and PEA stages and then, for later stages, to confirm the flowsheet selection and optimize the metallurgical efficiency of the plant. The testwork should consider all rock types or lithologies present, and carry out testwork for the purpose of sizing the major processing equipment.A successful project requires that the project stakeholders develop an efficient sample collection program to produce enough material for a scoping and pre-feasibility level program. This involves the participation of a team of geologists, mining and metallurgical engineers in the project, as early as possible, to define the deposit characteristics that need to be validated.The project schedule requires a close control of the testwork scope, procedures, and timing, but also the efficient analysis of results to provide indications of red flags that could impact circuit design as early as possible.In some cases, projects are put on hold due to fluctuations of the world economy until the return of more favorable conditions. In that scenario, prior data analysis of former testwork results could reduce significantly the amount of testwork required to restart a project. The paper will also present examples where the analysis of former testwork data was used to reduce the amount of new testwork in addition to presenting examples of latest projects where the above-mentioned test program approach was followed."

Jan 1, 2016

By B. Hoare, H. M. Hill

"SYNOPSISTailings volumes, disposal systems, effects of dam failures, construction materials, and concentrator process water volumes are discussed. Earth dams and tailings dams are discussed in detail. Some of the fundamentals of soil mechanics relating to earth dams are presented. Brief notes on optimization are presented. The development of a triplex meter for earth dam instrumentation is described. The advantages of the hydro-cycloned dam over the spigotted dam are outlined. INTRODUCTIONThe realistic and responsible recognition of the pollution problem, combined with the grossly increased volumes of waste material from large modern mining operations, has emphasized the demand for safe tailings dams at minimum cost.Tailings may be defined as the waste material from a mining operation after the process of concentration in which the minerals have been extracted for commercial use. The present revenue from the Canadian Mining Industry is slightly over $4,000,000,000 per year and it is estimated that the quantity of tailings produced exceeds 300,000,000 tons annually. In many instances, the volume of tailings from a mining operation is greater than the volume of crude ore mined on account of the small quantity of valuable mineral recovered during concentration, and on account of the ""swell factor"" resulting from the processes of drilling and blasting, crushing, and grinding of the crude ore. Some of the larger mine tailings deposits contain over 200,000,000 cubic yards and the associated tailings dams are among the largest man-ma.de structures in the world."

Jan 1, 1970

By Simon Houlding

"The objective of Part J of this paper is to identify the limitations of the traditional modelling methods and to illustrate, by example, the potential for error created by their application to complex deposits and mining situations. Part 2 describes the evolution of new, proven technology which eliminates these deficiencies and provides precise and practical alternatives. These promote the use of realistic geological and mining shapes and eliminate altogether the rectangular approximations of traditional methods.The Case for Precision ModellingIt is not the intent of this paper to promote the benefits of computer modelling per se. It is assumed that these are recognized by the mining industry in general. The concern of Part 1 is to identify, qualify and quantify (where possible) the limitations of the tractitional modelling methods. In many instances these methods continue to be applied to complex geological and mining situations for which they were never intended nor designed. The source and magnitude of the resulting errors, conflicts and inefficiencies are not always obvious, however, they can have far-reaching effects on the efficiency and profitability of mining operations.The conclusions support a rapidly growing demand by industry for practical, precise modelling technology which eliminates the deficiencies and can be applied with confidence to evaluation, design, planning and control of mine production in all situations. Part 2 describes new technology which has evolved in response to these industry pressures and has already been successfully applied to complex mining situations. This new technology can aptly be described as appropriate technology for the 1990s."

Jan 1, 1991

By N. Torres, G. Melcher

"An alternative to building new copper smelters, because of either stringent environmental regulations or in order to expand current plant capacity, could be achieved through the retrofitting of old reverberatory furnaces by making use of tonnage oxygen. The CONTOP® technology offers unique advantages over other techniques for this purpose, especially regarding substantial reduction in bath, capital and operating costs. This is possible to achieve since the reverb throughput could be largely increased with no major structural modifications to the furnace.The following options are offered to the smelter operators: dirty concentrates can be treated in an adjacent Contop system, or the cyclones can be mounted on the reverb roof for either dual operation or full Contop operation. ln the tatter case the furnace will be used as a settling chamber and f or slag c1eaning by top blowing with reducing gases.By incorporating Contop technology, the furnace throughput can be increased, higher malle grade, fixation of sulphur from furnace off-gas and substantial savings in energy consumption are possible to attain.IntroductionCopper smelting has been revolutionized during the last quarter century to such an extent that the standard type of plants consisting o f roasters and reverb furnaces seem a thing of the past, or almost. Though the building of new, more energy efficient smelters is a very likely opportunity for a grassroots plant, it would be hardly justifiable to replace an old existing plant unless there are heavy environmental or economic constraints(1,2,3)."

Jan 1, 1984

By C. A. Rowland

"Plant owners and operators, plant designers and grinding mill manufacturers are giving much attention to the design and manufacture of autogenous and semi-autogenous grinding mills, particularly the mills that have large diameters and draw power up to 10,000 hp and greater. Reliable designs giving long operating lives are required in today &apos;s ore processing plants.This paper reviews bench-scale and pilot-plant testing to determine first if the ore is suitable .to be ground by these methods and then reviews the data obtained from pilot-plant testing that is used to select the mills and the grinding circuit. The paper then discusses the use of the pilot-plant results to design the mills. The most important pilot-plant data used for mill design are power and the amount of ball charge to be used. The mill size selected is a combination of these factors. Pilot-plant data not only establish power requirements, but can be used in the selection of the type of drive, variable speed or fixed speed, and the operating procedure to be followed. This leads into the mill control circuit to be used. The total charge in the mill, the type of drive and mill discharge arrangements are needed in the calculation of stresses and bearing loads. Conclusions reached from pilot-plant work are used to obtain data for process design, and autogenous and semiautogenous mill design should be part of any test program incorporating either or both of these grinding methods."

Jan 1, 1981

By Wayne N. McKee, Scott A. Lewis

"Introduction to the Syncrude OperationSyncrude Canada Ltd., located 42 km north of the city of Fort McMurray, Alberta, (Fig. I) is an integrated operation that has produced synthetic crude oil from the Athabasca oil sand deposit since 1978.The operation, consisting of a surface mine, an extraction plant, a bitumen upgrader, and a utilities plant, is currently capable of producing over 60 million barrels of crude oil per year. Production is expected to increase to 70 million barrels of crude oil per year over the next five-year period with no major changes to equipment or process planned.The Syncrude surface mine, producing a total of 675 000 tonnes of ore and waste per day, rates as one of the largest mines in the world. A strip mining method is utilized, with two or three operating benches necessary to excavate a total depth varying between 60 m and 70 m. The 20 m to 30 m of overburden is removed by electric and hydraulic shovels and 200-ton haul trucks, and dumped in the mined-out pit for final storage. The overburden operation creates a flat bench near the top of the ore zone on which the four 60 m3 draglines operate. The draglines excavate interbanded ore and waste in the highwall, with ore placed on the operating bench in windrows, and waste returned to the mined-out pit. The windrowed ore is reclaimed by four bucketwheel reclaimers, and discharged onto a conveyor system for transfer to the extraction plant."

Jan 1, 1993

By T. R. C. Aston, C. M. K. Yuen, J. L. Gilby

"The access tunnels for the Donkin-Morien Mine in Cape Breton, Nova Scotia, comprise two parallel tunnels driven through a sedimentary sequence of sandstone, siltstone and mudstone to intersect the Harbour Coal Seam under the Atlantic Ocean, approximately 3.5 km offshore (Fig. 1). The No. 2 tunnel was driven a total distance of 3579 m using a 7.6 m diameter Loyat full-face tunnel boring machine (TBM) and was supported by steel sets. The No. 3 tunnel was initially driven a distance of 1027 m using drill and blast methods (dimensions 7.6 m wide by 5.3 m high) supported by rock bolts and shotcrete. This tunnel was then completed (front March 1986 to February 1987) using the tunnel boring machine to a distance of 3573 m.During the period May 1983 to December 1984, a major geotechnical research program was undertaken in the Donkin-Morien tunnels by Golder Associates in conjunction w,ith CANMET and the Cape Breton Development Corporation (Yuen et al., 1985). The research program included the monitoring of the performance of the TBM and drill and blast drivages, and the study of the thrusting characteristics and rock-interaction of the TBM excavation. The main emphasis of the research program was on the collection of field data which was to be made available in the form of a comprehensive report for the future use of others who might wish to carry out a detailed interpretation and analysis. The information gained from the program was also used during the tunnel"

Jan 1, 1988

By H. R. Oliveira, C. R. Aragonez de Vasconcellos

Pipeline operation and maintenance necessarily involves geotechnical studies at points and areas with deflagrated instabilities or still to map and monitor areas prone to geotechnical problems. Landslides, erosions and debris flows are some examples of natural hazards, that not rarely, can bring high consequences to pipelines, sometimes leading them to high stresses levels and ruptures. Bolivia-Brazil Natural Gas Pipeline has 2.593 kilometers since Rio Grande City in Bolivia until Canoas City, in south Brazil. The pipeline crosses a lot of types of geological fields and difficult topography. The south spread of the pipeline has the most prone areas to geotechnical hazards because of its hard topography combined with the variety of geological materials, such as, colluvium deposits and debris flow areas. The aim of this paper is to present the right-of-way geotechnical risks that affect pipelines, presenting some practical remedial works done by TBG at Bolivia-Brazil Natural Gas Pipeline as well as the integrity plan and the adopted actions in way to prevent geotechnical accidents.

Jan 1, 2005

By T. M. Ahmed

Sherritt International Corporation experienced corrosion failures with the 316L stainless steel tubing in a high-pressure still condenser employed for ammonia recovery. A detailed failure analysis was conducted on the condenser tubing to determine the mode and the root cause of the failure. The analysis included both optical and scanning electron microscopy (SEM) of the inner and outer surfaces of the tube as well as characterization of the corrosion products using energy-dispersive X-ray spectroscopy (EDX). Results revealed that the corrosion attack was confined to the first ?100 mm of the tubing at the inlet where the tube was connected to the top tubesheet. The tube suffered both external stress-corrosion cracking (SCC) and crevice corrosion from the shell side (water side), and wall thinning of the inner surface (the tube side) due to erosion corrosion. It was evident that failure of one of the tubes occurred due to SCC that penetrated the whole wall thickness and resulted in a leak failure. Some prevention measures are proposed to avoid this type of corrosion attack in the future.

Jan 1, 2005

By D. Tao

Froth flotation is widely used in the coal industry to clean -28 mesh or -100 mesh fine coal. A successful recovery of particles by flotation depends on efficient particle-bubble collision and attachment with minimal subsequent particle detachment from bubble. Flotation is effective in a narrow size range outside which the flotation efficiency drops sharply. A fundamental analysis has shown that use of picobubbles can significantly improve the flotation recovery of particles by increasing the probability of collision and attachment and reducing the probability of detachment. A specially designed column with a picobubble generator has been developed for enhanced recovery of fine coal particles. Picobubbles were produced based on the hydrodynamic cavitation principle. Experimental results with one metallurgical coal and one steam coal have shown that the use of picobubbles in a 2" column flotation increased fine coal recovery by 10-30%, depending on the feed rate, collector dosage, and other flotation conditions. Picobubbles also acted as a secondary collector and reduced the collector dosage by one third to one half.

Jan 1, 2006