Search Documents

By D. Y. Li, C. D. Ma, T. Zhou, T. J. Cheng

In this paper, a number of experimental tests are carried out to study the strength difference on rectangular prismatic marble specimens with different height-to-width (H/W) rations. The specimens have a nominal size of 45×15 mm in the compressive cross-section (W×T) and different heights (H = 22.5 mm, 45 mm, 60 mm and 90 mm). It is to say that the height-to-width ratios are equal to 0.5, 1.0, 1.33 and 2.0, respectively. The quasi-static uniaxial compressive tests are finished by a servo-controlled INSTRON machine (the strain rate at about 10-5/s), and the dynamic compressive tests are finished by a diameter of 50 mm cylindrical SHPB apparatus (the strain rate reaching about 101/s). The rock failure process of marble specimens is captured by a high speed camera in order to distinguish the fracture propagation behaviour. It is found that the compressive strengths increase when the H/W ratio of marble specimen changes from 2.0 to 1.0 due to the end clamping effect both for quasi-static and dynamic loads. However, when the H/W ratio changes from 1.0 to 0.5, the apparent compressive strengths decrease both for the two loading conditions. The strength decrease of short marble specimens may be attributed to the change of failure mode from shear to slabbing, which can be identified by the fracture patterns of the specimens. Based on the uniaxial compressive tests, the slabbing strength of the marble was found to be about 40% of its UCS for the specimens with a nominal height-to-width ratio of 2.0. In addition, it is found that the dynamic increase factors (DIF) are affected by the specimen’s aspect ratios. It implies that the same aspect ratios should be used to compare the dynamic and static compressive strength of rocks. Meanwhile, both the static and dynamic tensile strengths of the marble are obtained by the Brazilian disc tests. The ratio of the dynamic tensile strength to the static tensile strength of the marble is about 2.68.

Jan 1, 2015

By Peter A. Amelunxen, Richard LaDouceur, Courtney A. Young

"Many of the rare earth elements, the lanthanide series on the periodic table, are on the U.S. Department of Defense Strategic and Critical Materials list. In this regard, the U.S. Army Research Laboratory (ARL) has funded several projects at Montana Tech focusing on rare earth element recovery from natural resources. Current froth flotation operations utilize octyl hydroxamate for rare earth mineral extraction, however recovery is not ideal and flotation performance can be improved. Salicylhydroxamic acid (C7H7NO3) was identified as a novel collector due to similarities with n-octyl hydroxamate, notably the amine head group. Salicylhydroxamic acid is primarily used in the medical industry but due to the amine head group is ideally suited as a collector for rare earth mineral flotation.Parametric studies were performed for the flotation of rare earth minerals by modifying a wide range of variables. Mechanical variables of a 6L bench scale flotation cell, such as air inlet flow, rotor speed, and milling time for liberation were modified to elucidate energy input parameters for the desired minerals. Chemical parameters such as collector concentration and pH were varied to understand solution chemistry considerations of the salicylhydroxamic-rare earth mineral system. The study obtained a statistically significant experimental model for the flotation of rare earth minerals. A two stage compartmental model was also utilized for the determination of the first order flotation rate constants for each mineral. Optimized recovery of rare earth minerals was found to occur at near neutral pH ranges using salicylhydroxamic acid with maximum recoveries approaching ideal industrial standards although rare earth mineral grades were still not sufficient.INTRODUCTIONRare earth elements (REEs) are found in minerals that contain several REE which makes costeffective separation of the rare earths difficult. Significant scientific challenges have hindered mineral separation. The molecular similarity of rare earth elements results in minerals containing several REEs, such as bastnaesite [(Ce, La) CO3F]. This prevents efficient separation during concentration steps, for instance flotation, and has a direct impact on successive metallurgical processes. Consequently, concentration during flotation is of rare earth minerals (REM) as opposed to REE."

Jan 1, 2016

"Successive seismic waves may cause progressive weakening of a fault zone, which has been recognized as the mechanism of earthquake aftershocks. However, it is unclear that how a fault zone slips under each wave cycle and how slip displacement accumulates under continuous wave cycles. This laboratory study provides direct evidences on the slip process of a simulated granular fault zone dynamically induced by an incident wave without the effects of late-arriving and reflected waves. The experimental observations show forward and backward slip paths of the fault zone and partially recovered slip displacement after a wave incidence. The unrecovered slip displacement after each wave cycle can be accumulated until it reaches a critical slip distance for seismic faulting, which may reinterpret delayed triggering in earthquake dynamics. The limited interseismic period restricts fault self-healing in strength. The experimental results also indicate that the dynamically induced frictional slip on the fault zone is associated with a complex frictional system, including seismic wave radiation, frictional slip initiation and normal stress vibration. Different from the dynamically induced frictional slip on the fault zone, the statically induced frictional slip causes a permanent increase of slip displacement along the shear loading direction. INTRODUCTIONAn earthquake mainshock may induce aftershocks by suddenly changing external stresses applied to another fault zone in the near field (Kilb et al., 2000) and by slightly perturbing a fault zone from a critical steady state to stick-slip faulting in the far field (Gomberg and Davis, 1996). The dynamically induced frictional slip on a fault zone has been recognized as the mechanism of earthquake aftershocks (Marsan and Lengliné, 2008; van der Elst and Brodsky, 2010). Although earthquake aftershocks have been extensively studied by many seismological methods, a simplified laboratory fault zone can provide possible interpretation on real faulting and detailed analysis on a friction process (Dieterich, 1979; Nielsen at al., 2010). According to a few laboratory experiments related to the dynamically induced frictional slip on a simulated fault zone (e.g., Uenishi et al., 1999; Johnson et al., 2012), the slip process induced by successive seismic waves exhibits continuous motions. However, it is unclear that fault slip response under each wave cycle and slip displacement accumulation under continuous wave cycles."

Jan 1, 2015

By Yong Kang, Bingyuan Yan, Dandan Zheng, Xiaochuan Wang, Dengfeng Su, Dongyang Li

"According to the characteristics of rock mass and the directional cutting technology of water jet, a new idea of light shock controlled blasting with water jet slotting was put forward. Based on the fracture mechanics theory and the stress wave theory, the mechanism of damping with water jet slotting was analyzed. On the basis of the above, the evolution law of the pressure wave and displacement field during the blasting were simulated by FEM software ANSYS/LS-DYNA. The result shows that: the oriented slot plays a good role in orientation during the blasting, and makes the energy generated by gas released by the explosives gather at the tip of the oriented slot, which makes it easier for the main crack to expand along the oriented slot and indirectly reduce the stress effect on the protected object. Meanwhile, the energy of the seismic wave is reduced while transmitting through damping slot. Finally, compared with the normal blasting with damping ditch, the maximum acceleration is reduced by 15.62%, the maximum velocity is reduced by 52.99%, and the maximum displacement is reduced by 68.32%. INTRODUCTIONIn recent years, with increasing demand for energy and space, an increasing number of underground projects have been under construction. Drilling-blasting method, as a traditional main method for rock excavation, is still an indispensable means in the engineering construction. As is known, blasting vibration will cause the deformation and unstable of the existing building structures, so how to reduce the influence on the existing building structures caused by the blasting vibration has become the focus. Traditional shock absorption measures mainly include three kinds: the first one is pre-splitting blasting, the second measure is to change the parameter of explosive filling, and the last one is to excavate damping ditch between the protected object and blastholes. However, engineering practices show that: the protected rock may be damaged in the process of pre-splitting crack construction by blasting, the second measure is difficult in operating, and the third measure is troubled by large work quantity (Song Guangming, 1999; Lou Jianwu, 2004; Lou Jianwu, 2005; Li Xibing et al., 2008)."

Jan 1, 2015

By G. Deschênes

The Eleonore property (James Bay district of Northern Québec), owned by Goldcorp, hosts gold within stockworks of quartz-tourmaline-arsenopyrite veins and veinlets contained within microcline (potassic alteration) and brown tourmaline replacement zones. The preliminary investigation to recover gold from drill core samples showed that flotation followed ultrafine grinding and cyanidation is the preferred option. Ultrafine grinding is used to liberate gold finely disseminated in sulphides. The flotation concentrate used in the investigation had a P80 of 11 microns and contained 75.5 g/t Au, 5.0 g/t Ag, 10.3% S, 0.07% Cu and traces of antimony (0.03%). The mineralogical characterization showed the presence of 65% gangue minerals, 23% pyrrhotite (hexagonal), 9.6% arsenopyrite, 2.2% pyrite and 0.08% chalcopyrite with trace amounts of galena (0.05%) and sphalerite (0.03%). Gold was in the form of native gold and electrum. A straight cyanidation conducted at pH 11.0, DO of 3-5 ppm, 2000 ppm NaCN, 20 C 72 hours extracted 97.0% Au and consumed 31.5 kg/t NaCN. The equilibrium was reached within 24 hours. Increasing the dissolved oxygen to 16 ppm reduced the consumption of cyanide to 22.0 kg/t with 96.7% Au extraction. A 16-h pretreatment with 2.0 kg/t lead nitrate, followed by a 24-h cyanidation reduced the cyanide consumption to 6.0 kg/t with a gold extraction of 97.5%. Increasing the lead nitrate addition to 6.0 kg/t reduced the cyanide consumption to 1.2 kg/t by passivating the surface of pyrrhotite. The gold extraction remained at 97.0%. It was possible to decrease the concentration of cyanide to 800 ppm NaCN without compromising gold extraction. The associated cyanide consumption was 1.2 kg/t NaCN. The passivation of gold grains was an issue when the cyanide concentration was decreased to 550 ppm NaCN. The gold extraction decreased to 92.2%. The average lime addition for all the tests was 7.4 kg/t and the average silver extraction was 80%. Efficient cyanidation of an ultrafine sulphide concentrate with only 800 ppm NaCN represents an advance in leaching of ultrafine sulphide concentrates.

Jan 1, 2013

By Donald Leroux, Ralph Dahlke, Dave Scott, Finch. James A., Cesar O. Gomez

"The efficiency of the flotation process depends on how effectively air is dispersed into small bubbles. Bubble surface area flux - the surface area of bubbles per unit time per unit cross-section area of a cell - is emerging as the parameter to characterize gas dispersion. One of the approaches proposed to measure bubble surface area flux in industrial cells is based on the measurement of two variables: gas velocity and gas holdup, using separate sensors. Plant testing of the gas velocity sensor gave evidence of a series of operational problems which may be necessary to correct before attempting to characterize gas dispersion. Problems such as uneven air distribution within a cell and along a bank, faulty air and slurry valves detected during attempts to redistribute air, and poor control of pulp level and gas flow became evident. Detection of these problems from gas velocity measurements is illustrated.INTRODUCTIONBubble surface area flux is considered a key variable in the optimization of flotation circuit performance (Gorain et al., 1997; 1998). The Mineral Processing Group at McGill University has devised and developed a method for estimating bubble surface area flux in industrial flotation cells (Finch et al., 1999). The method is based on measuring gas holdup and superficial gas velocity using two separate sensors and applying drift flux analysis to estimate bubble size (Dobby et al., 1988; Banisi and Finch, 1994). With bubble size and superficial gas velocity known bubble surface area flux can be calculated.This method was selected by Noranda to characterize gas dispersion in cells as part of a program to model and optimize flotation circuit performance. However, initial testing at Brunswick Mine with the gas velocity sensor provided some unexpected results indicating operational problems and equipment malfunctions that needed to be addressed before systematic measurement of gas dispersion could be initiated.The subject of this communication is to illustrate the detection of these problems from gas velocity measurements. The line 3 Zn Cleaner circuit comprising four stages of Denver DR cells was the main subject of analysis, including the effect of correcting these problems on the metallurgical performance of the Zn 3rd cleaner bank of ten DRl 00 cells."

Jan 1, 2001

By P. Scinto, A. Festa

"Orway Mineral Consultants Ltd (OMC) as a consultancy has specialized in comminution circuit design for over 30 years. The OMC Power Model is OMC’s in-house software for specific grinding energy power-based circuit calculations. The model uses ore hardness parameters from testwork, circuit configuration, equipment geometry and operating conditions as inputs. The model combines proprietary and published power models to predict the total specific energy and the specific energy for each of the components of the comminution circuit. This makes the software a valuable tool for the design and validation of JKSimMet modelling or actual plant performance. Proprietary calculations have been developed and reconciled with over 100 plant benchmark projects encompassing a variety of comminution circuit configurations.This paper describes the OMC approach for determining power requirements for the design of grinding circuits. The accuracy of the OMC Power Model software is confirmed through plant survey benchmark performance and comparisons are made with other power modelling techniques. Practical examples are presented, showing applications for single stage SAG (SS-SAG), SAB and SABC circuit configurations.IntroductionConventional low throughput grinding options, consisting of multi-stage crushing followed by rod and ball mills, have almost become obsolete in the move to higher milling rates required to process lower metal grades. Grinding circuits with fully autogenous (AG) or semi-autogenous (SAG) mills, often combined with ball mills are now the standard to meet the high capacity requirement for processing ores with lower metal grades. Simulation software and power-based equation methodologies have been established for designing AG/SAG based grinding circuits and predicting their energy requirements.Presently, power-based equations remain the principal method for designers to size mills and estimate the power requirement for comminution circuits. The technique is simple and it relies on the design to specify a feed and product size plus a hardness index to produce a specific energy value (kWh/t). The desired throughput of the mill is multiplied by the specific energy to give the mill power requirement, which is used in turn to size a mill for dimensions, internal geometry and loading conditions to match the power draw."

Jan 1, 2015

By Matthew S. Bingham, David H. Searle

"One of the most significant developments in environmental law has been the development of mandatory project review processes, at both the federal and provincial levels.FederalWhile, in the past, project review processes have, f or the most part, been spelled out in guidelines, the guidelines have not had the force of law. All that has changed, particularly at the federal level, with the Federal Court decisions commonly referred to as the Old Man River and Alameda and Rafferty Dam cases. These decisions, taken as a whole, are authority for the proposition that the Environmental Assessment and Review Process Guidelines Order, SOR 82-487 is a law of general application, not a mere guideline which may or may not be applied. This federal environmental assessment process first provides for a screening, and, depending upon the results of the screening process, the possibility of a public review. This federal process only applies, however, when the proposal is being undertaken by a federal department, or where the Government of Canada makes a financial contribution, or where federal lands are involved, or where a federal licence or permit is required.Bill C-78, the Canadian Environmental Assessment Act, will replace the Federal Environmental Assessment and Review Process Guidelines Order once it has been passed by Parliament. Currently the bill is being widely discussed, both between governments as well as public interest groups.ProvincialOn the provincial scene, there are three project review processes, one concerned with new mines, the second with energy projects and the third with all other major projects. The most recent initiatives taken by British Columbia are twofold. First, the Mine Development Review Process which was in the form of a guideline, has been replaced by the Mine Development Assessment Act. Second, the Major Project Review Process has been formulated and is to apply to four main categories of major projects:1. Pulp and paper production;2. Mineral smelting and refining;3. Chemical products; and4. Major ports and marinas.Energy projects are governed by the Energy Project Review Process which is legislatively mandated under the Utilities Commission Act."

Jan 1, 1991

By R. J. Mitchell

"Centrifuge modelling of earth structures is a well-proven technique for evaluating the performance of prototype structures using physical models. The applications of this technique have increased dramatically during the last decade such that even the modelling of dynamic responses in structures has been accomplished.This paper presents the first model test results used to design a mine backfill. The models were tested using a 3 m radius 30 g-tonne geotechnical centrifuge which was constructed at Queen's University specifically for model studies on mine backfill stability and subsidence. The models represent the first production blast-hole stope to be mined at Westmin Resources Ltd. 's H. ~ Mine on Vancouver Island. This paper includes photographs of:model failures in the centrifuge and correlations of model test results with analyses based on unconfined and triaxial test data.IntroductionDuring the feasibility study and development stages for the H.W. Mine, Westmin Resources Ltd. conducted a comprehensive rock mechanics and backfill engineering program. The results of these studies indicated the need for assurance of backfill stability during pillar recovery on the initial blast-hole mining block. The cemented tailings backfill had to be free standing for heights up to 25 m and the potential for surcharge loading from a weak hanging wall zone, the potential for fill block sliding down-dip and the potential for seismic loading had to be considered in the design of the fill strength. The basic questions to be answered were: what cement content is required and will the resulting backfill costs be economic relative to the proposed mining method and sequence? Figure I shows a typical cross-section through the first mining block . The up-dip stope is to be mined first and backfilled with cemented tailings . The down-dip stope would then be mined and filled. Depending on ground conditions encountered, the complete intervening pillar could be recovered and the void backfilled with uncemented tailings or it could be recovered in small sections by exposing limited back and wall areas, backfilling with waste rock and I or cemented tailings . This latter method is commonly referred to as the Avoca method"

Jan 1, 1987

By H. Craig Boyle, Craig H. B. Leitch

"The Trout Lake stockwork molybdenum deposit is located in the Selkirk Mountains of British Columbia, 50 km southeast of Revelstoke. The property is being explored by a joint venture between Newmont Exploration of Canada and Esso Minerals Canada.The deposit is associated with a small granodiorite stock of Upper Cretaceous age (76 Ma) which has variably altered the surrounding schists, argillites and marbles of the lower Paleozoic Lardeau Group to hornjelsic biotite schists and skarn. The intrusive is composed of a small stock and an intersecting network of northeast- and northwest-trending dykes at surface that coalesce downward into a larger stock. There are two main phases of intrusion, with an earlier quartz porphyritic granodiorite cut by an intra-mineral ""quartz diorite"" porphyry. A strong sub-vertical north-trending fault controls the distribution of the mineralized stock work and displays post-mineral movement.Molybdenite, accompanied by pyrite and pyrrhotite, is mainly present along the margins of veins in a well-developed quartz stock work, but occasionally is strongly disseminated in microfractured intrusives. The stock work is strongest in and around the contacts of the intrusive and its apophyses, and occurs over a vertical range of more than 1,000 m. As defined by the 0.10% MoS] contour, the main mineralized zone is up to 300 m long by 200m wide. Preliminary drill-indicated reserves, currently being revised, are approximately 50 million tonnes of 0.23% MoS2, within which are several zones of higher-grade material. Hydrothermal alteration, as defined by quantitative X-ray diffraction studies on composite core sections, is composed of a central quartz/K-feldspar/albite/minor biotite zone coincident with molybdenum mineralization, which is overlapped by a slightly later, antipathetic quartz/ sericite/pyrite zone. Ankeritic carbonate is also a common alteration mineral, but only traces of fluorite, and no topaz or sulfosalts, have been observed. Analysis for trace elements such as Sn, W, Bi, Sb, As, Hg, U, Ag, Au, Mn, Cu, Pb, Zn and F has been limited except for Sn and W, which appear to be zoned inside and outside the Mo zone respectively; the other elements do not show detectable patterns thus far."

Jan 1, 1983

By C. Mattich, Å. Holmström, L. Hedström

"The fluidized bed at Division Ministro Hales (DMH) division of Codelco in Calama, Chile is currently the largest operating roaster for partial roasting of arsenic rich copper concentrates. The roaster converts the Mina Ministro Hales (MMH) enargite rich (Cu3AsS4) copper concentrates into calcine with a low arsenic content that is suitable for mixing with other copper concentrates feeding a flash furnace. The plant sets a new standard for the processing of arsenic rich concentrates, both from the quality of the calcine as well as the environmental performances. The process technology and expertise are based on the solid practical experience of treating arsenic rich concentrates from both the Boliden smelter and Outotec.The partial roasting process is located next to the mine and concentrator and includes a sulphuric acid plant with auxiliary equipment. The produced calcine has an arsenic content significantly below target and the residual sulphur meets the requirement of the flash furnace. The plant operates with high efficiency cyclones resulting in a low amount of calcine passing to the hot electrostatic precipitator (HESP). The small flow of HESP calcine dust can be combined with the low arsenic calcine and still meet the flash furnace feed arsenic requirements.SO2 formed during roasting is converted into sulphuric acid, while volatized arsenic is recovered in the wet gas cleaning section of the acid plant along with a large proportion of antimony present in the MMH concentrate. Arsenic is stabilized as calcium arsenate and sent to disposal at a specially prepared site.The present production rate (September/October 2015) is close to or higher than the original maximum design capacity of the plant.INTRODUCTIONMineralogyThe mineralogy of an ore and concentrate is important, since there is a direct link between roasting performance and concentrate mineralogy. The MMH concentrate has a good combination of minerals that makes the roasting process efficient and flexible. The main minerals are pyrite, enargite and chalcocite (Figure 1). The inert content is about 15% and consists mainly of silicate and alumina based minerals. The lead content is very low and this is desirable, since the presence of even a small amount of lead will cause a substantial increase of sintering during roasting."

Jan 1, 2016

By I. Silin, M. Stapelmann, H. Wotruba, K. M. Hahn, C. Gerold, J. Katzmarzyk

New deposits are often characterized as low-grade and complex ore bodies. To date, processing of fine grained ore deposits implies complex processing routes with high energy consumption. For that reason, the investigation of dry grinding, e.g. with vertical roller mills (VRM), is an approach to save energy reserves. It is already proven that dry grinding can influence subsequent processing steps. In terms of flotation, the surface characteristics of the minerals are crucial for a successful flotation process, e.g. the sufficient adhesion of mineral particles and air bubbles. Wet grinding results in different surface properties of the product entering the conditioning stage than dry grinding, which has direct influences on the subsequent flotation process. To investigate the consequences for flotation, processing of a copper sulfide ore containing chalcopyrite and bornite was investigated, including grinding and rougher flotation. The effects of wet tumbling mill and dry VRM grinding on the degree of liberation of valuable minerals are characterized using mineral liberation analysis by scanning electron microscopy. The obtained flotation results, as well as the recorded flotation parameters such as dissolved oxygen, oxidation reduction potential and conductivity are presented and discussed. INTRODUCTION Copper production is mainly connected to porphyry copper deposits as main source for copper sulfides such as chalcopyrite and bornite. State-of-the-art processing of these deposits is already established worldwide for decades, combining crushing, fine grinding and subsequent flotation with rougher, cleaner and scavenger stages (del Villar, Desbiens, & Maldonado, Bouchard, 2010). While the demand for copper is increasing, copper grades of the deposits are decreasing and the remaining ore bodies have more complex mineralogy and finer particle size distribution. This implies processing routes with high water and – due to the liberation of fine grained valuable minerals – high energy consumption by fine grinding. One of the main energy consumers in processing plants is the grinding section, which accounts for more than 50% of the energy consumption in processing plants and even 4% of the worldwide energy consumption (Jeswiet, & Szekeres, 2016). Therefore, dry fine grinding alternatives are applied to enhance the overall energy consumption of mineral processing plants: high pressure grinding rolls (HPGR) and vertical roller mills (VRM).

Jan 1, 2019

By Zorigtkhuu Davaanyam, Fisher Wang, Bern Klein, Amit Kumar

"The High Pressure Grinding Roll (HPGR) is an increasingly popular energy efficient solution for comminution of competent ore deposits that primarily competes with conventional crushers and tumbling mills. A significant barrier to increased adoption of HPGRs is the requirement for large amounts (one tonne or more) of sample for pilot testing which may not be feasible for most early staged projects.Various researchers have worked towards developing piston-die and JK drop weight tests to model and predict the energy requirements for an HPGR. Two small scale laboratory test procedures (the SMC test (Morrell, 2009) and the piston press tests (Davaanyam, 2015)) have been developed in recent years to provide necessary information to size an HPGR.These two methods were used to estimate the required specific energy for an HPGR unit and compared to HPGR pilot scale test results from a copper deposit. The comparison provides insight into the benefits and limitations of these tests.INTRODUCTIONHigh pressure grinding rolls (HPGR) have gained popularity in recent years because of their energy efficiency in comminution. Various researchers have suggested that approximately 50–80% of the total energy consumed in a mineral processing plant is used by the comminution equipment (Haque, 1999; Abouzeid & Fuerstenau, 2009; Wang, 2013). Haque (1999) showed that the efficiency of grinding equipment can be as low as 1%. Due to the energy intensive nature of comminution, mining industry has been forced to explore alternative energy efficient processes.An HPGR based circuit has been shown to be 10–25% more energy efficient than a conventional SABC circuit (Von Michaelis, 2009; Wang, 2013). A significant barrier to the increased adaptation of HPGRs is the requirement for a large amount of sample for pilot testing (up to 5 tons), even on a prefeasibility level. Numerous studies have been performed to utilize piston press test to analyze the performance of the HPGR circuit and to predict the energy consumption for an industrial application. This paper uses two small scale laboratory test procedures, the SMC test and a piston press test, to compare the energy requirement to the pilot HPGR data."

Jan 1, 2016

By A. J. Rigby

The wear mechanisms of the tuyere lines of Peirce-Smith and Hoboken converters are a subject of endless debate and speculation. However, there has been an indication that one of the primary factors in the deterioration of tuyere lines is due to the batch operation of the converting process. The cooling of the brick in the tuyere line during out-of-stack times leads to shrinkage of the brick and resultant opening of the joints. Subsequently, on re-entry of the tuyere line into the bath, the joints become penetrated with matte and re- expansion of the brick is prevented. It is thought that this regular cycle of exiting the batch for slag skimming and replenishment of matte and re-entering for further blowing leads to a gradual “ratcheting” of the tuyere brick lining. If no expansion allowance is furnished between the endplate and the endwall of the lining, then the generation of damaging compressive stress is unavoidable. INTRODUCTION It is generally accepted industry-wide that the integrity of a refractory lined vessel is determined by an inextricable combination of refractory brick quality, the caliber of the lining design and installation, and the severity of the process inflicted upon the high wear areas of the vessel lining. Rigby has summarized the concentrated attempt, over the past several years, to optimize the microstructural, chemical, and fracture properties of the refractories used in non-ferrous pyrometallurgical vessels. Furthermore, lining design concepts involving larger and longer brick and the extent and positioning of expansion allowance in the joints have been extensively trialed. All these efforts have provided some, but not startling, improvements. The simple fact is that a vessel lining composed of bricks with an optimized microstructure and chemical inertness must installed with a well-conceived design to decompress the lining stresses that are generated by the batch operation of copper converters. REFRACTORY QUALITY Converting is conducted by injecting air into the molten matte and white metal for the very purpose of generating iron and copper oxide slags. These slags must be contained by a refractory which, by its mineralogical formulation, is optimized for chemical inertness.

Jan 1, 2019

By David Minson

On many occasions, operators have seen that high density and paste thickener performance does not meet the initial design expectations, and the installed equipment produces lower than expected thickener underflow solids content. This lower-density tailings slurry leads to more water and lower beaching angles being seen at the tailings storage facility (TSF). This not only reduces storage capacity, but also increases the risks of non-compliance with environmental permit constraints. Reasons for the shortfall in performance can be many, but perhaps the main problem is inadequate understanding of the critical components of thickener design and operation, with too much reliance placed on standardised design terminology; such as tph/m2. This paper discusses additional factors that influence high-density thickener operation and presents test work that defines “Dynamic Slurry Fluidity”, “Bed Compaction Rates”, and “Natural Slump Angles” for these high yield stress/viscosity slurries. Finally, the paper uses this data to define thickener geometry, drive torque, floor slope(s), rake blade configuration and how this can be used to provide engineers with more tools for in depth evaluation of a High-Density thickener design. INTRODUCTION Generally copper mines are high tonnage operations, with copper flotation concentrators producing high volumes of tailings slurries of milled solids and water. As a result, Tailings Storage Facilities (TSF) become very large and this, along with potential scarcity of water, favours a design that maximises storage space. In theory, the use of filtration equipment that achieves immediate water recovery, high TSF in-situ densities and high stacking angles are preferred for this duty. However, large tailings filter units are uncommon, and have high operating and capital costs that favour the use of thickeners. The use of high-density thickeners to produce a thick or near-paste like slurry with high un- sheared yield stress values above 100 Pascals, is becoming more common. The higher thickener underflow is required to not only maximise water recirculation within the mill, but to also increase beaching angles, maximise tailings storage capacity and minimise evaporation losses arising from large areas of superficial water. However, the reliability of this equipment is also under scrutiny and there is perhaps a need to better define these designs.

Jan 1, 2019

By M. L. Jeremic

"Hydraulic mining consists of coal erosion by powerful jet s of water from hydraulic monitors operated by remote control. The broken coal is crushed and mixed with water and then transported from the face to the surface using gravity whenever possible. This is a simple, safe and productive method. It will easily satisfy North American productivity standards if the structural features and coal properties are favourable for water jet cutting technology (Kaiser Resources Ltd. , hydraulic mine). General ConsiderationIn open-pit mines, placer mining (Fig. I) and hydroelectric construction projects, hydraulic earth moving techniques have been successfully applied. The stripping and transporting of the overburden has been accomplished by means of large monitor jets augmented by slurry pumps and pipes. An extension of this technique has led to the underground extraction of coal and ores. To date, the method has been most successfully used in undergrond coal mining, because the coal can be easily cut and flushed away by water jets, and the rocks of the roof strata can be left behind. Due to this favourable situation, the hydraulic mining definition only relates to the underground coal mines.At present, there are four basic types of hydraulic mining, which can be defined according to the coal breaking technique used in each case. The methods are briefly discussed below:(1) Coal excavation may be carried out by conventional techniques, but the mine is designed and equipped for the hydraulic transport of the mineral from the working place to surface. Under these circumstances, the coal breaking may not be influenced by the water jet, however it may be indirectly involved. For example, pre-loosening of the coal may be done by water infusion-hydraulic fracturing. Water may also be used to flush the broken coal, which has been excavated either by drilling and blasting or by mechanical cutting, into the transport flumes. In other cases, a mechanical loader may load the coal directly into the hydraulic transport system, without using any water for the extraction process. This hydraulic mining concept is primarily used for hard and impermeable coal, such as anthracite."

Jan 1, 1980

By John A. Meech

"Oleic acid flotation of Mount Wright thickener underflow tailing material has been shown to be capable of increasing plant recovery by 3%. High levels of oleic acid addition (1.5 kg/t) are required, which limit the economic practicality of the system at this time. Nevertheless, from a technical viewpoint, the process is stable with respect to extreme fluctuations in oleic acid requirements, pulp pH and pulp temperature. Methods to reduce the average consumption of oleic acid need to be found. One technique that merits further testwork uses the ""piggy-back"" principle to float hematite fines with coarsegrained hematite particles.IntroductionWith most large-scale iron mining operations treating specular hematite ores, flotation is not often conside red a necessary processing step. The bulk of the iron minerals can be concentrated by gravity techniques and the generation of fines can be minimized because of the course- grained nature of the mineralization. Nevertheless, production of some fine material is unavoidable, and recovery of iron from this fraction by spirals is poor (10-30%).When the proportion of the iron in these fines becomes excessive, alternative methods to conventional spirals are considered(11), Many of the techniques that have been developed suffer from either poor recovery (e.g. the Reichert cones at 36010 recovery)(11) or low throughput rates (e.g. wet highintensity magnetic separation)(12), Flotation is often passed over because of excessive reagent costs, pollution problems and/or balling difficulties from the reagents used.However, of all the processes available, flotation can yield high recoveries (60-90%) at reasonable throughput rates with excellent process control features (reagent addition and/or cell level). The key parameter is reagent cost.This paper describes testwork on the use of oleic acid to float hematite from the fine fractions of the Mount Wright concentrator tailing. The concentrate product from this plant is directly shipped, so no balling problems exist. As well, oleic acid may be considered a lesser pollution hazard than many of the cationic collectors used in other iron ore flotation systems. A reduction in fine hematite slimes discharged as tailing into lakes may also reduce environmental damage."

Jan 1, 1981

By Stanley G. Butcher

"The methods generally applied to predict performance and financially evaluate beneficiation options are reviewed.Typical costs f or a western Canadian thermal coal operation are examined. Preparation-from truck dump to loadout-frequently amounts 10 over a quarter of total minesite costs. Failure to achieve projected yield-whether caused by mine or plant problems-s-substantially increases production costs because more coal has 10 he mined to meet a specific market demand. Problem identification by mass/ash balances is recommended.Thorough characterization of the coal and associated waste materials and more reliable prediction of beneficiation process performance are therefore essential to determine a project 's financial viability.IntroductionWestern Canadian coal prep a ration plant capacity is partway through a massive expansion program . In 198 1 potential product ion was 14 million tonnes, by 1985 it will be 26 million tonnes per year. Only two years ago the industry was concerned whether it could sustain this rate of growth to meet market demands : now with diminished market demand and lower coal prices being offered by our international competitors there are doubts whether t his potential will be fully employed , even by 1990.One direct consequence o f the occurrence of a variety of coals in a stunningly beautiful but complex geo logical setting such as the Rocky Mountains and their Foothills is that each project is unique. Coal is a low value per tonne product. To supply distant markets from geographically isolated deposit s necessitates expensive , dedicated , infrastructure . T o be profitable these operations must achieve eve ry advantage of the economy of scale.Each of the mi ne complexes commissioned in the 1970s experienced severe problems in the area o f co a l preparation . Most bought their way out , paying for major plant modifications by increasing the scale of their total operation . The current market recession may not allow new operations this route to profitability.The objective of this paper is to illustrate the economic impact of coal preparation problems on the profitability o f the total minesite operation and thus provide a sound basis for decision making process."

Jan 1, 1985

By T. P. Lim, N. K. Davé

"A modified accumulator method was devised to measure surface radon flux from porous media. It consists of a collector hood type of accumulator with a homogenizer pump and a pressure balancer. The latter was used to compensate any pressure changes produced during sample withdrawal and hence eliminate additional radon transport from the media. Errors resulting from radon back diffusion due to decreasing concentration gradient with time across the interface were also eliminated by measuring radon concentrations in the accumulator for two different periods of time and calculating the true radon flux, J(o), from the solution of a time-dependent radon transport equation in the absence of any pressure and temperature gradients.Core samples from the observation site were also withdrawn for laboratory determination of porosity, moisture content, bulk and grain densities, Ra-226 source concentration and the fraction of Rn-222 produced in the void volume. The data were used to calculate the radon diffusion coefficient for the media.Using the present method, the true value of surface radon flux for an abandoned uranium tailings pile was obtained as J(o) = 2020.2 mBq/m2/sec (54.6 pCi/m2/sec) compared to the value J = 1406.0 mBq/m2/sec (38.0 pCi/m2/sec) obtained by the conventional method. The bulk diffusion coefficient of radon for the media was obtained as 1.2 x 10-7 m2/sec.IntroductionRadon-222 (hereafter called radon) released from uranium mill tailings is a continuous source of environment radioactivity in terms of its transport as an airborne gas and its decay products. The particulate daughter products readily attach to aerosols or dust particles and can further be transported by various other environmental pathways. Typical radon release rates from existing tailings piles vary between 740 and 14,800 mBq/m2/sec (20-400 pCilm2/sec), depending on the nature of the tailings material, moisture content, etc. The United States Nuclear Regulatory Commission (NRC) is proposing radon release rates of 74 mBq/m2/sec (2 pCi/m2/sec) above that of background."

Jan 1, 1982

By P. Mayer

"Determining the correct mechanism of a boiler tube failure is important for the prevention of future tube failures. Proper corrective measures can be undertaken to alleviate the root cause or causes for a failure only when the correct mechanism is known. A mechanism of boiler tube failure is defined as the process which degrades the tube and produces a failure.An expert system package was developed for use by electric utility power plant personnel during investigation into the cause of a boiler tube failure. It is intended to assist their efforts to recognize and identify a basic failure mechanism that can produce the type of boiler tube failure under investigation. The program guides the user to the most likely failure mechanism by asking simple questions, answers which can be obtained by determining the failure location, type of fuel, and from visual inspection of the failed tube. Expert systems are a form of artificial intelligence which imitate the decision-making process of experts.IntroductionBoiler tube failures (BTFs) continue to be the single largest source of forced outages in fossil fired electricity generating stations. Because of this a concentrated effort is being made to minimize boiler tube failure occurrences. Eliminating boiler tube failures could be worth $5 billion a year to the electric power industry(1).The aggressive service environment of fossil-fired boilers is largely the reason for these failures because the combined effects of stress, temperature, corrosion, erosion and vibration cause deterioration of boiler tube material properties and reduction in wall thickness.Determination of the boiler tube failure mechanism is important for the prevention of future problems. The root cause for a failure can be established and proper ameliorative measures taken only when the failure mechanism is identified correctly. The correct identification of failure mechanism is a complex process which may include many individuals and institutions. Technical specialists in metallurgy, chemistry, combustion, and boiler design frequently cooperate with the station staff in a failure investigation . These individuals rely on personal experience and numerous reports , theories, studies, private communications and investigations concerning the different failure modes and mechanisms."

Jan 1, 1990