Search Documents

By R. F. Favreau

"After a blast, the volume of the blasted rock normally occupies more space that it did before the explosion. The degree of such swell significantly affects the efficiency of digging the muck with a shovel or dragline. This paper explains why swell occurs, and describes the new subroutine SWELL of the blast simulator BLASP A which can simulate blast-induced swell. Results are also presented which display the effect of various blasting parameters on the degree and distribution of the swell within the muck pile of a bench blast. IntroductionIt is a common opinion that fragmentation is the most important of the various aspects which affect the efficiency of excavating rock with explosives. This paper proposes that, in fact, displacement and swell of the blasted rock are as important as fragmentation if the excavation process is to be rapid and efficient. It must ""a priori"" be recognized that a minimum degree of fragmentation is indeed necessary. For a given shovel or dragline, this minimum degree of fragmentation may be defined as follows: even the largest fragment of rock must be easily contained within the bucket. Once this criterion is met, however, there are good reasons to believe that displacement and swell take over as the key criteria which influence the rate of mucking, in cubic metres/hour. If the muck pile is not well displaced and swelled, the teeth of the bucket have difficulty penetrating between the rock fragments even if fragmentation is good and, as a result, the mucking is slow and inefficient. The purpose of this paper is to use computer simulations on the model BLASP A to demonstrate the effect of the blast design parameters on the displacement and swell of the blasted rock."

Jan 1, 1993

By T. T. Chen, J. E. Dutrizac, G. Poirier

In the Waelz kiln process, EAF dust is converted to an Fe-rich slag, a (Zn, Fe)-rich dust that is recycled to the kiln and the Zn-rich Waelz oxide which is subsequently up-graded for the recovery of zinc. To clarify the reactions occurring, the Waelz kiln products from a European Waelz plant were characterized mineralogically to determine the mineral species present, their micro-textures and the metal carriers. The EAF dust contains 27 % Zn, and consists mainly of ZnFe2O4 and ZnO, together with minor to trace amounts of NaCl, PbCl2, KCl, CaO, Ca2Fe2O5, Fe203, FRO, Pb oxide and various Ca-Fe-Al-Mn silicates. The KCI and NaCI sometimes agglomerate the other particles. The slag consists of nodules which often exhibit colloform structures. The slag contains of variable amounts of Fe, FeO(OH), FeO, gypsum, Ca(OH)2, Ca2SiO4 and various Ca-Fe¬Al-Mg-Mn silicates as well as minor to trace amounts of ZnFe2O4, Cr-Fe oxide, Mn-Fe oxide and other species. The Waelz oxide contains 57-61 % Zn, and consists predominantly of ZnO, with minor to trace amounts of KCI NaCl, Pb(OH)Cl, Pb20(SO4), Pb chloride, ZnSO4, ZnFe2O4, Ca2SiO4, Ca2Fe2O5, Ca-Fe silicate and NaZn4(SO4)(OH)6Cl.6H2O. The KCI agglomerates the other particles in the Waelz oxide. The recycled dust appears to be a mixture of EAF dust and Waelz oxide, but it contains relatively more coarser-grained metallic Pb and Pb oxide particles.

Jan 1, 2004

By J. Wild, M. Ounpuu, G. Chevalier

"The requirements for a finer grind at Heath Steele have resulted in the investigation of agitated milling as a cost effective alternative to conventional tumbling ball mills.The grinding unit is a vertically agitated, or stirred ball mill. Grinding occurs as the result of the motion of a single vertical rotor equipped with protruding pins which impart a stirring action to the ball charge. A comparative evaluation of a 30 kW SALA Agitated Mill (SAM), and a 1.5 m x 2.5 m copper-lead regrind ball mill has been conducted at Heath Steele.An overview of agitated milling as it applies to the reduction of sulphide ore will be the primary topic for discussion. Specific parameters including energy efficiency, media consumption, operating costs, and the mechanical aspects of the SAM operation will be presented.Evaluation of the agitated mill has shown that improved grinding performance at much lower work indices than those of the conventional ball mill is possible. Media consumption has proven to be comparable on an average g/kWh basis, but the mechanical availability of the mill has been low.INTRODUCTIONConventional tumbling ball mill grinding has proven to be an energy inefficient process. Energy losses occurring within the ball mill itself can be attributed to particle friction without breakage, kinetic and potential energy losses, plastic and elastic deformation and the production of heat and sound (Lynch, 1977). It can be generally stated that a certain amount of the input energy will be converted to another form as a necessary by-product of particle breakage. Theoretical interpretation of experimental results indicate that the energy required for breaking the ore particles in a ball mill varies between I% and 25% of the total energy input (SME, 1985)."

Jan 1, 1993

By A. J. Sinclair

Abstract-Exploratory data evaluation is an essential part of every high quality, mineral inventory estimate. Efficient analysis involves a thorough organization of available quantitative data that are the basis of the estimate and perhaps the formation of composite grades. Data organization and evaluation can involve more than 50% of the time necessary to conduct a mineral inventory estimation. The principal purpose of exploratory data evaluation in mineral inventory work is to improve the quality of estimation by providing insight into characteristics of the variables under investigation. Specific aims include: (1) to recognize and eliminate errors; (2) to provide a comprehensive knowledge of the statistical characteristics of all variables of interest for resource/reserve estimation; (3) to document and understand the interrelationships among the variables of interest; (4) to recognize systematic spatial variation of variables such as grade and thickness of mineralized zones; (5) to recognize and define distinctive geological domains that require independent estimation of mineral inventory; (6) to identify and characterize outliers; and (7) to evaluate similarity/dissimilarity of various types of raw data, especially samples of different supports. These aims are not mutually exclusive but they can all have their own impact on resource/reserve estimation. Error must be minimized. Individual variables can have characteristics that lead to different decisions in the course of estimation. Similarly, interrelations of variables might contribute to the ease (or difficulty) with which estimates of several variables can be obtained. Trends can impose the need for two or more domains, each of which might be estimated independent of the others. Outliers, a perennial problem, require detailed evaluations because they impact on reserves much out of proportion to their abundance. Data, of widely different supports, generally must be standardized if all are to be used for purposes of estimation.

Jan 1, 1998

By Andrew Neale, Len Anderson, Rob Perry

"P.T Freeport Indonesia's new SAG mill commenced operation in February 1995. The reclaim system consists of four apron feeders and a series of three conveyors. The feeders are used in various combinations and relative speeds to blend SAG mill feed. It was recognized during design of the control system that effective automatic control would require dead-time and gain compensation. The successful implementation of the Dahlin algorithm to provide variable dead-time and gain compensation is described and compared to Pl control.RésumeL'opération du nouveau SAG de P.T. Freeport Indonésie a commencé en Février 1995. Le système de réclamation du minerai comprend 4 alimentateurs à tablier et une série de 3 convoyeurs. Les alimentateurs sont utilisés dans une combinaison variée et à des vitesses relatives différentes pour mélanger l'alimentation du SAG. II a été reconnu pendant la conception du système du contrôle que le contrôle automatique demandera une compensation pour le temps de délai et le gain. L'implantation de l'algorithme de Dahlin a été un succès et ii est comparé avec le contrôle Pl.ResumenP.T. Freeport Indonesia inició la operación de un molino semi autogeno (SAG) en febrero de 1995. El mineral es alimentado desde cuatro alimentadores tipo apron feeders y una serie de correas transportadoras. Los alimentadores se utilizan en variadas combinaciones y velocidades para mezclar apropiadamente el mineral que alimenta al molino SAG. Durante el diseño del sistema de control se detectó que el control automático requería de un tiempo muerto y compensaci6n de ganancia. En este documento se describe la implementación del algoritmo de Dahlin, que ha sido exitosa y ha permitido proveer tiempos muertos variables y compensaci6n de ganancia. Ademas se hace una comparaci6n con el Pl de control."

Jan 1, 1996

By R. T. Seaman

There are several hydrometallurgical alternative processing options under development for high enargite and arsenic containing copper concentrates ranging from biological, atmospheric, medium temperature oxidation to total oxidative leaching. The most developed of these options is the CESL process boasting pilot campaigns totaling more than 8760 hours of fully integrated continuous operation, as well as, over two thousand batch scale oxidation tests performed on dozens of concentrates for flowsheet development. This paper reports the observed deportment of arsenic under varying arsenic, iron and acid oxidation conditions; it also describes the impact of iron to arsenic ratios and residue recycle on overall arsenic behavior and its stability in residue. INTRODUCTION The CESL Hydrometallurgical Process (CESL) was originally developed to compete with smelting of clean chalcopyrite concentrates. High Treatment Charges and Refining Charges (TC/RCs) combined with premiums on London Metal Exchange (LME) grade copper from onsite refining made treatment of copper concentrates using CESL a viable option at the time. As world demand for copper increased and a subsidized Chinese refining market developed, smelting contracts became more favourable for the miner and focus was placed on modifying the CESL Hydrometallurgical Process to handle concentrates with elevated deleterious elements. Dozens of pilot campaigns processing concentrates containing elevated concentrations of uranium, fluoride, mercury and nickel all led to further developments of the CESL Hydrometallurgical Process. In 2016 a United States patent was granted for a novel modification of the CESL Hydrometallurgical Process for recovery of copper from arsenic-bearing and/or antimony-bearing copper sulphide concentrates, Henry Salomon de Friedberg (2016). To date, over 2000 bench scale tests along with five fully integrated closed loop pilot campaigns, totaling over a year of online operation time, have been conducted processing arsenic bearing copper concentrates. This paper summarizes the observed behavior of arsenic under varying autoclave and process conditions.

Jan 1, 2019

By Randolph A. Pax

"The internal operation of a tumbling mill is a very hostile environment and precludes the sustainable operation of internal sensors to measure the mechanisms of charge motion and breakage events. Instead indirect methodologies are required to expand the current understanding developed within a framework of perfect mixing of the mill contents. A number of measurement approaches have been successfully used to explore the operation of SAG mills including strain instrumented lifter bolts, mill shell strain measurement and thermal (energy balance) of operating mills.Early acoustics measurement was developed by Hardinge using a 'microphone' located close to the expected toe location. This signal was an indicator of the mill fill. Improvements were implemented with the use of two microphones straddling the toe location to try to increase the sensitivity of the measurement and reduce ambiguities. Further improvements included a filtered signal indicative of steel interactions. Unfortunately, the mechanisms of signal generation and the complexity of the processes do not provide a consistent signal.In recent years, advanced acoustic measurement using arrays of microphones utilising signal processing techniques have been implemented as SmartNoise and validated on over 30 mills. This paper will discuss the results obtained with signals such as water holdup, mill shell steel hits and two each of the toe and shoulder angles. An estimate of the internal mill component wear rates is also accessible.Advanced acoustic measurements with wide bandwidths when combined with physics models and process understanding has achieved a step change in the understanding of the dynamic internal operation of a tumbling mills on time scales of 80 ms. These techniques have been used extensively on SAG mills, but have also been applied to FAG and ball mills. Acoustic measurement is used for the rapid diagnosis of mill conditions and holistic control for optimisation and stability."

Jan 1, 2016

By Daniel Hodouin, Robert Lanthier, Yve Dube

"A procedure f or constructing a grinding mill dynamic model is proposed. This model is used in a dynamic simulator of are grinding circuits. The simulator is designed for flexible flow sheets involving different grinding mills and particle classifiers and is able to accept several single variable PID control loops. The dynamic model is validated on a laboratory ball mill, and calibrated to an industrial installation. The simulator is used for characterization of grinding circuit dynamic behaviour and tuning of control strategiesIntroductionThe ore grinding operation is a critical step of the ore preparation process because it is the last comminution stage before the separation of minerals. The properties of the ground minerals to be concentrated, control the quality and efficiency of the separation process. This is why it is important to control properly the operation of the last grinding stage, commonly constituted of a closed circuit ball mill with classifier . To provide an adequate fine product, the grinding operation should compensate for the perturbations of the feed characteristics (size analysis, grindability, etc.). The main objective is to maintain a constant size distribution for providing stable operating conditions to the separation units. Simultaneously another usual objective is to operate the grinding circuit at a maximum capacity.Automatic control applied to grinding circuit s is the appropriate approach to improve its operation. Most frequently average optimal operating conditions are determined from steady -state performances of the circuit , and the automatic control is used for stabilizing the operation at selected values of the process variables . In the traditional approach, one or several single input! single output (SISO) control loops are implemented and empirically tuned. Advanced control practices'!' are based on a quantitative analysis of the circuit dynamics, which could also give a basis for the tuning of conventional SISO 100ps(2)."

Jan 1, 1987

By L. A. Homeniuk, R. Bonnar

"The Fond-du-Lac uranium deposit is located on the northern rim of the Athabasca Basin. The uranium mineralization is, for the most part, confined to the Athabasca Group, which is underlain by pre-Helikian metamorphic rocks of the Western Craton.The deposit is characterized by a remarkable train of mineralized glacial erratics which led to the original discovery. The mineralization is present as a ""high-grade"" core and a diffuse ""low-grade"" aureole. The ""high-grade"" core occurs as a stockwork of steeply dipping pitchblende veins which strike N 50°E. Hematite, siderite and secondary silicate are also abundant. The ""low-grade"" aureole contains uraniferous goethite, argillaceous material and rare carbon buttons. Recent alteration to coffinite has taken place along the margins of pre-existing ore minerals.The ""high-grade"" core is 390 m long and 10 to 40 m wide, and is surrounded by an irregularly shaped zone of ""low-grade"" mineralization with a similar length and a width of up to 350 m.Comparing the Fond-du-Lac deposit to other unconformity-type deposits, several important differences can be noted:1. Ninety per cent of the ore is above the unconformity, in the Athabasca sandstone.2. The deposit is not associated with underlying graphitic rocks or a major structure.3. The clay-rich alteration zone is not extensive around the Fond-du-Lac deposit.Although there are differences with other Athabasca unconformity-type deposits, the high-grade portion below the unconformity suggests a common origin.The ore deposit is postulated to have been formed from uranium-bearing solutions which entered the stockwork of fractures. Following the reduction in part of these solutions by pre-existing carbonaceous matter and pyrite and/or chemical reaction with pre-existing hematite, deposition continued as a result of decreasing temperature and pressure. Subsequently, minor supergene redistribution of the uranium has taken place."

Jan 1, 1982

By L. A. Homeniuk, R. Bonnar

"The Fond-du-Lac uranium deposit is located on the northern rim of the Athabasca Basin. The uranium mineralization is, for the most part, confined to the Athabasca Group, which is underlain by pre-Helikian metamorphic rocks of the Western Craton.The deposit is characterized by a remarkable train of mineralized glacial erratics which led to the original discovery. The mineralization is present as a ""high-grade"" core and a diffuse ""low-grade"" aureole. The ""high-grade"" core occurs as a stockwork of steeply dipping pitchblende veins which strike N 50°E. Hematite, siderite and secondary silicate are also abundant. The ""low-grade"" aureole contains uraniferous goethite, argillaceous material and rare carbon buttons. Recent alteration to coffinite has taken place along the margins of pre-existing ore minerals.The ""high-grade"" core is 390 m long and 10 to 40 m wide, and is surrounded by an irregularly shaped zone of ""low-grade"" mineralization with a similar length and a width of up to 350 m.Comparing the Fond-du-Lac deposit to other unconformity-type deposits, several important differences can be noted:1. Ninety per cent of the ore is above the unconformity, in the Athabasca sandstone.2. The deposit is not associated with underlying graphitic rocks or a major structure.3. The clay-rich alteration zone is not extensive around the Fond-du-Lac deposit.Although there are differences with other Athabasca unconformity-type deposits, the high-grade portion below the unconformity suggests a common origin.The ore deposit is postulated to have been formed from uranium-bearing solutions which entered the stockwork of fractures. Following the reduction in part of these solutions by pre-existing carbonaceous matter and pyrite and/or chemical reaction with pre-existing hematite, deposition continued as a result of decreasing temperature and pressure. Subsequently, minor supergene redistribution of the uranium has taken place."

Jan 1, 1982

By M. W. Gilmore, J. Ndlovu, T. Sepoloane, Anglo American Platinum, L. R. Nelson, R. N. Varty, L. J. Bryson, B. Peyper, J. P. Hagemann

"As part of Anglo American Platinum’s Rustenburg Base Metals Refinery (RBMR) expansion, a new Nickel Electrowinning Tank House, with a nameplate capacity of 32 400 tons per annum, was constructed. Commissioning of the new electrowinning technology, which involved world first full deposit plating, commenced in 2011.The old nickel electrowinning process at the RBMR used starter sheets which, along with a divided cell configuration, was very labour intensive and exposed operators to high levels of aerosols that contained both nickel and acid. To overcome this problem two key design intents of the new technology are aerosol abatement and minimising labour in the electrowinning cell environment, with a design target to reduce the nickel occupational exposure limit (OEL) to half the legislated limit of 0.1 mg.m-3.Commissioning of the new technologies adopted to achieve mist abatement is described, together with a review of technical and operational challenges relating to the titanium blank edge strips, blank roughness and sandblasting optimisation, blank quality control, electrode spacing, polyconcrete cell dimensional stability and cell top furniture. The impact of these on process performance is presented and the development of fault checking and rectification methods, to maintain high process performance, is explained.INTRODUCTIONThe expansion of Anglo American Platinum’s Rustenburg Base Metals Refinery necessitated the construction of a new Nickel Tank House to achieve two primary objectives, namely increasing the nickel electrowinning capacity from 22 500 tons per annum (tpa) to 32 400 tpa nickel, and a design to reduce the nickel aerosols to 0.05 mg.m-3 as a time weighted average over 8 hours, which is half of the legislated occupational exposure limit (OEL) of 0.1 mg.m-3."

Jan 1, 2016

ABSTRACT Based on mineralogical characteristics and processing techniques required, gold ores can be classified into 12 types: gold placers, quartz vein-lode ores, oxidized ores, silver-rich ores, iron oxide copper-gold ores, porphyry copper-gold ores, iron sulphide ores, arsenic sulphide ores, antimony sulphide ores, bismuth sulphide ores, telluride ores, and carbonaceous sulphide ores. The bulk mineralogy and gold deportment of each ore type differs and may have a significant impact on ore processing and metal extraction. This paper summarizes the bulk mineralogy and gold deportment in some major types of gold ore and discusses the potential impact of gold deportment on gold metallurgy.

Jan 1, 2013

By J Zhou

Based on the mineralogical characteristics and mineral processing techniques required, gold ores can be classified into 12 types, including gold placers, quartz vein-lode ores, oxidized ores, silver-rich ores, iron oxide copper gold ores, porphyry copper gold ores, iron sulphide ores, arsenic sulphide ores, antimony sulphide ores, bismuth sulphide ores, telluride ores and carbonaceous sulphide ores. The bulk mineralogy and gold deportment of each ore type is different and may have a significant impact on ore processing and metal extraction. This paper summarizes the bulk mineralogy and gold deportment in some major types of gold ores and discusses the potential impact of gold deportment on gold metallurgy.

Jan 1, 2011

By B. W. Williams

The crack propagation behaviour of Zr-2.5Nb pressure tube material was studied through comparison of the measured behaviour with the predicted response from finite element analysis. Three-dimensional finite element simulations of compact tension specimens were performed using the crack tip opening angle as a fracture criterion to allow for crack propagation. To obtain reasonable agreement with the measured behaviour, it was important to capture both the anisotropic plastic deformation behaviour of the Zr-2.5Nb material through use of the Hill-48 yield criterion and damage due to void growth, nucleation, and coalescence through the use of a Gurson-based constitutive model in the simulations.

Jan 1, 2010

By P. A. Crane, N. Shirley, Aung Moe, H. M. Nicholson, D. Kan

Kazakhstan’s first commercial copper-leach solvent extraction-electrowinning plant, Central Asia Metals’ Kounrad project, was commissioned in April 2012. Exploiting low grade waste stockpiles produced during Soviet era open pit mining, a 10,000 tpa copper cathode plant was designed, constructed and commissioned within 18 months. Overcoming initial challenges with a workforce unfamiliar with the technology and with extensive periods of sub-zero conditions during winter the project has consistently met targets and produced high quality copper cathodes at cash costs of less than US$1/lb. Challenges encountered during the first two years of operation are described and future plans briefly discussed.

Jan 1, 2014

This paper focuses on the dissolution of various Manganese based compact additions into liquid Magnesium. The experimental procedure employed cylindrical compacts with various Manganese compositions. The various temperatures of the additions and the Magnesium bath were measured simultaneously during the immersion of the additions into Magnesium bath. The exothermicity level of these additions during their dissolution into liquid Magnesium was determined. The relation of the exothermicity level with the dissolution kinetics was also examined. In addition, SEM and EDX work was conducted for additions, which were withdrawn from the Magnesium bath. Finally, the recovery of these additions was estimated by taking samples from the Magnesium bath and conducting ICP analyses.

Jan 1, 2006

By M. R. Khalesi, S. Bellec, C. Bazin, D. Hodouin

Batch grinding tests conducted on a gold ore indicated that gold is not randomly distributed within the size fractions of the ground ore. Since gold leaching performances were found to be dependent of the size of the gold carrying particles an integrated gold ore grinding-leaching simulator should incorporate a method to predict the gold size distribution of a ground ore. The paper describes the results obtained from batch grinding tests showing the non random distribution of gold within the size intervals of a ground ore and the initial developments of a grinding model to predict the gold size distribution in a batch grinding product.

Jan 1, 2011

By J. Lu, J. B. Wiskel, D. G. Ivey, E. Niemi, H. Henein

Simulated TMCP using a Gleeble was undertaken to evaluate the effect of the austenite to ferrite cooling rate, coiling temperatures of either 400°C or 500°C and the magnitude of plastic deformation at the coiling temperature on the hardness of a Grade 483 (X70) steel. For comparable apparent cooling rates and deformation conditions, the hardness of the samples were independent of coiling temperature The application of a minimum compressive deformation > 8% was required to increase hardness at both simulated coiling temperatures of 400°C and 500°C. An increase in hardness was also observed with increased cooling times between 800°C and 500°C (i.e., slower cooling rates).

Jan 1, 2005

By R. W. Lawrence, O. Lopez

Many gold deposits in the world have not been developed clue to the presence of copper and other base metals which can cause metallurgical and environmental challenges clue to the formation of base metal cyanide complexes. SART technology (sulphidization-acidification-recycle-thickening) can resolve these issues by recovering copper as a high grade sulphide concentrate, recycling the associated cyanide back to the gold leach, and eliminating the downstream environmental liabilities. Project economics can be improved substantially, leading to a positive re-evaluation of new and existing gold-copper projects. Some aspects of the design and operation of two recently commissioned SART plants will be discussed.

Jan 1, 2011

By Bennett McLaughlin

AGNICO-EAGLE started sinking the Penna Shaft in 1995 with a hoisting plant capable of hoisting 1,800 tonnes per day from a 2,240 metre deep shaft. Exploration success lead to the installation of a hoisting plant capable of extracting 4,500 tonnes of ore and 1,800 tonnes of waste per day from a depth of 2,210 metres. The introduction of a new rope selection factor, permitting a safety factor of 4.0, represented the breakthrough required for a cost-effective project. This paper describes the process taken to introduce the new rope selection factor and its impact on the original plant.

May 1, 2001