Search Documents

By D. Letzig

Wrought magnesium alloys are of special interest as lightweight structural components as a result of their more homogeneous microstructures and improved mechanical properties compared to cast components. Extrusion as a shaping technology offers the possibility to produce a wide variety of magnesium alloy profiles. In this contribution we describe the role of extrusion parameters such as extrusion speed, ratio and temperature as well as the type of extrusion process on the microstructural development of AZ-series magnesium alloys and the resulting mechanical properties. The effect of microstructure on the tensile/compression deformation behavior of the alloys has also been investigated. Aspects of process optimization designed to overcome technical and economic limitations and thus establish magnesium alloy profiles for industrial applications will also be discussed.

Jan 1, 2006

By E. Lovera

ABSTRACT: The current study analyzes the feasibility of an odd operation: to obtain, using a properly tailored drilling and blasting scheme, blocks suitable for the production of dimension stone from tunnel driving. Clearly, a compromise must be found between the rate of progression and the achievement of workable blocks. As a case study, a civil work under consideration in northern Italy was examined. The work was planned to cross a conglomerate that has traditionally been locally exploited for the production of highly prized paving and lining stones with excellent strength and aesthetic features. Natural exposures and mined-out quarries were available for tests. The relevant rock data are given, blast designs are shown (within the limitations of contour accuracy), and the test program is described.

Jan 1, 2011

By D. B. Dreisinger, M. R. Tavakoli

Vanadium has been produced from both primary and secondary sources having various compositions. Vanadium pentoxide and vanadium trioxide are the most available and known sources of vanadium oxides. In this paper, an overview of leaching both oxides has been reported. The problem of vanadium pentoxide leaching under acid conditions is the low solubility of the dissolved vanadium. This was investigated and then supplemented with further studies of leaching at mildly basic pH’s as well as under acid reductive leaching conditions (to form vanadium (IV)). Atmospheric oxidative leaching of vanadium trioxide was investigated using oxygen and ferric ion as the oxidant. It was shown that the leaching of vanadium trioxide using oxygen is very slow; however, ferric ion can dramatically increase the kinetics and leach efficiency.

Jan 1, 2014

By Baisheng Nie

The process of gas diffusion through coal particles and the mathematical physical model under the third kind boundary condition was determined to obtain the rules of gas diffusion through coal particles of different sizes. The analytical solution of the equation was obtained by the Method of Mathematical Physics. The parameters of analytical solutions and the implications of parameters were analyzed. The Biot criterion (Bi) and the Fourier criterion (F0) of mass transfer can represent and reflect the features of gas diffusion field of coal particles. Moreover, the measurement method of gas diffusion coefficient and surface mass transfer coefficient is introduced and an example of measurement is given. The achievement can provide the support to prevent disasters related to methane in coal mines.

Aug 1, 2013

By H. Dundar

An extensive testwork was performed around the HPGR plant at GoldFields Ghana Limited Tarkwa Gold Mine. The HPGR was used to prepare the feed for heap leaching. The circuit was configured in such a way that the edge material from the HPGR discharge was recycled for further crushing while the product from the centre reported to the heap leach section. The set-up of the Polysius HPGR provided an opportunity to study the effect of different design and operating variables. This paper will discuss the results from the tests performed to assess the effect of rolls? speed and applied pressure on the capacity and the grinding efficiency of the HPGR. Applying different pressure values appeared to have an influence on the amount of edge material recycled.

Jan 1, 2012

By M. Tadayonsaidi

The effect of alloying elements on the mechanical properties and thermal expansion of 336 casting alloy usually used as piston alloy which has low thermal expansion and very good high-temperature mechanical properties and good wear resistance was investigated. The mechanical properties and thermal expansion characteristic of samples with different combination of alloying elements, which enhance to reduce the cost of products, have been studies, The results show remarkable increase in the mechanical properties with increasing the amount of Cu and Mg, while are reduced with increasing amount of Ni, On the other hand, the use of eutectic aluminum alloy as 336 alloy with higher percent of Cu and Mg and lower percent of Ni are recommended for industry, due to economical viewpoint and satisfactory properties.

Jan 1, 2005

By E. Dernedde

A few studies have suggested that the rate of adsorption of hydrogen fluoride on smelter grade alumina is determined by kinetic factors. However, no performance equation for dry scrubbers has appeared in the literature so far. Experimental data from a pilot dry scrubber with co-current flow were compared with results of kinetic models of adsorption, film diffusion and pore diffusion. The pore diffusion model was deemed the most appropriate. It was transformed into a performance equation for steady-state operations of dry scrubbers by the inclusion of the alumina recirculation. Operating results of industrial dry scrubbers with co-current flow were successfully evaluated by means of the performance equation. The average fluoride content of the alumina was also estimated by using the pore diffusion model.

Jan 1, 2011

By Desmond Y. M. Lee

This paper presents a procedure to prepare input for the computerized pit design system at Iron Ore Company of Canada. The procedure is simple and requires very little training. Also, it is general enough to accept both bench (horizontal cross section) maps and section (vertical cross section) maps. The output of this procedure is data which represent blocks of ore and waste with dollar values based on mineral content. The ultimate pit design is presented in printer-generated graphs, with numbers indicating the depths of pit bottom walls. Roads are added manually by the engineer with the aid of other computer programs. Section maps and bench maps are also printed as part of the output of the ultimate pit design.

Jan 1, 1978

By H. B. Sahu, N. M. Mishra, D. C. Panigrahi

The paper presents the development of a spontaneous heating liability index (SHLI) of coal based on a mathematical approach. The parameters for the calculation of this index have been determined by differential scanning calorimetric studies. Thirty-one coal samples representing both fiery and non-fiery coal seams of different ranks have been collected from different Indian coalfields and their SHLI values have been determined. In addition, the susceptibility of these samples to spontaneous combustion has been ascertained by standard crossing-point temperature measurement. The moisture percentage of all the samples has been obtained by proximate analysis. A comparative study between SHLI and crossing-point temperature, along with moisture percentage, indicates that SHLI predicts the proneness of coal to spontaneous heating more accurately.

Jan 1, 2008

By L. Sun

In this work, strontium doped lanthanum ferrite (LSF) and their composite cathodes were fabricated by screen printing on yttria-stabilized zirconia (YSZ) electrolytes. Their electrochemical properties were evaluated by using electrochemical impedance spectroscopy and steady-state polarization methods. All the cathodes were screened by comparing their total polarization resistances before and after activation processes at different temperatures. The improved LSF composite cathodes were also screen-printed on YSZ/NiO half cells to fabricate solid oxide fuel cells (SOFCs), which have reached the output power densities of 170 mW/cm2 at 650 °C, 230 mW/cm2 at 700 °C, 304 mW/cm2 at 750 °C and 388 mW/cm2 at 800 °C.

Jan 1, 2005

By A. J. Rigby

Anode vessels are often relined with refractory every one to two years and a typical reline time can take between 16-20 days. Modem refractory designs using dense, corrosion resistant brick applied directly to the vessel shell in the high wear areas around and above the tuyeres and at the slagline can yield a lining life of up to 4-5 years before a complete reline is necessary. Installation methods using brick delivery on roller conveyors through an endwall access port and complete anchoring of the brick to allow for lining self-support can take days off the installation time. It is possible, therefore, to reduce the refractory relining period by 50% and increase lining life by 100% compared to typical anode repair schemes. Cu2007

Jan 1, 2007

SOFCs with thin electrolyte of two types: SDC (15um) single-layer and YSZ (5um) + SDC (15um) bi-layer were fabricated by screen printing and co-firing on Ni¬YSZ cermet substrates. Using in-situ sintered Sm0.5Sr0.5CoO3 cathode the SDC-cell shows high performance at low temperature, 1180mW/cm2 peak power density around 650°C, while the YSZ+SDC bi-layer cell generates about 340mW/cm2 at 650°C, and good performance at 700-800°C with almost theoretical OCV value. Many Zr-content micro-islands were found on the SDC electrolyte surface. The influence of co-firing temperature and thin film preparation methods on the Zr-islands' appearance was investigated.

Jan 1, 2005

By F. Malek

At Creighton Mine, magnitude events are a regular occurrence due to depth and major seismically-active structures. Over the last ten years, major advances have been made in research and development to develop strategies for the management of these major events. Today, the number of rockbursts has been drastically reduced at the mine and damage due to seismic events, when they occur, is often minimal. This paper describes the evolution and implementation of appropriate geomechanics strategies, designs, and practical ground control measures undertaken for the management of seismicity at Vale Inco?s Creighton Mine. A description of the research and development approach, implementation, and ground control strategy is provided for placement of enhanced support systems to manage the consequences of magnitude events at Creighton

May 1, 2009

By T. G. Joseph

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an ?apparent friction? concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of tri-axial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock.

May 1, 2002

By J. Z. Cui

In this paper a statistical multi-scale method for the mechanics parameter prediction of the rock mass with random distribution of multi-scale cracks/joints is presented. First the micro-structure of the rock mass with random distribution of multi-scale cracks/joints is represented. Then the statistical second-order two-scale method for the mechanics performance predictions of the rock mass structure with random cracks/joints distribution is presented, including the statistical second-order two-scale expression on the vector-valued displacement, strain tensor and stress tensor, and the algorithm procedure of statistical multi-sale computation for the mechanics parameters. Finally some numerical results for mechanical parameters for the rock mass with random distributions of multi-scale joints/cracks by statistical multi-scale method are shown.

May 1, 2009

By A. Sadough vanini A. Kami

In this paper, effects of different ageing treatments on the mechanical properties, microstructure and formability of 7075 aluminum alloy have been studied. Forming limit diagrams of the alloy have been obtained for four ageing conditions including T6, OA1, OA2 and O. For this purpose, combination of uniaxial tensile tests and the Erichsen cupping tests with different sizes and shapes of sheet specimens have been performed after each ageing treatment. The highest formability and the lowest formability have been observed at samples with O and T6 ageing treatments, respectively. Also, investigation of precipitated microstructures showed that the size of precipitation particles has a significant effect on the formability of the alloy. Formability improves with coarsening of precipitation particles.

Oct 1, 2011

By Sadough vanini Ali

The silicon anisotropic wet chemical etching technique is widely employed for fabricating various microelectromechanical system (MEMS) structures for advantages such as simple etching equipment and its capability to fabricate special microstructures. In this paper, we consider a complete theoretical derivation of the analytical solution based on geometrical and kinetic aspects of step flow on any surface and with a mathematical method we derive new equation for calculating the microscopic etch rates of surface atoms for a new range of concentrations and temperatures. Furthermore, a novel equation is presented for the calculation of the microscopic activation energies for some typical surface atoms and a new comparison of activation energies between some atoms is made that divides atoms into three categories. The results demonstrate agreement with the experimental results.

Oct 1, 2011

By J. Larose, E. Irissou

The aerospace business has always been driven by innovation. A significant portion of the overall business technology development strategies is still based today on improved materials and coatings. In this highly regulatory business environment, large amounts of funding are required to increase the maturity level of novel technologies, but the evolution process still remains a delicate endeavor. The technical risks involved during technology development obviously need to be managed and mitigated throughout the development cycle, but other hurdles almost inevitably get encountered, such as budget limitations, transition from lab scale to production scale, loss of focus, intellectual property negotiations and supply chain integrity. This presentation will cover some of the issues raised when a great idea is slowly morphed into an aerospace production part.

Jan 1, 2010

By J. Fournier

A novel sol ? gel (SG) synthesis procedure utilizing varying ratios of glycine and ethylene glycol to total metal cations has been developed to create high purity nanometer sized La0.65Sr3.5MnO3 powders. X-ray powder diffraction (XRD), transmission and scanning electron microscopy (TEM, SEM), and dynamic light scattering (DLS) have confirmed that the crystallite sizes of such powders are ~ 20 nm, and the aggregate particle sizes vary between 100 to 300 nm. Mixing varying weight percents of SG LSM powders with commercially available Praxair LSM in a composite LSM/YSZ functionally graded cathode has been shown, through the use of electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV), to exhibit enhanced oxygen reduction kinetics vs. at conventional cathode materials.

Jan 1, 2005

By J. Fournier

A novel sol ? gel (SG) synthesis procedure utilizing varying ratios of glycine and ethylene glycol to total metal cations has been developed to create high purity nanometer sized La0.65Sr3.5MnO3 powders. X-ray powder diffraction (XRD), transmission and scanning electron microscopy (TEM, SEM), and dynamic light scattering (DLS) have confirmed that the crystallite sizes of such powders are ~ 20 nm, and the aggregate particle sizes vary between 100 to 300 nm. Mixing varying weight percents of SG LSM powders with commercially available Praxair LSM in a composite LSM/YSZ functionally graded cathode has been shown, through the use of electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV), to exhibit enhanced oxygen reduction kinetics vs. at conventional cathode materials.

Jan 1, 2005