Search Documents

By P. Carlone, A. Astarita, F. Rubino

Cold gas dynamic spray is an innovative technology allowing the deposition of thin metallic layers on a bulk or sheet substrate. Titanium on aluminum deposition is very attractive to the aeronautic industry, due to the enhanced corrosion resistance and wear properties of titanium coating as well as its improved compatibility with CFRP, preserving the reduced cost of aluminum substrate. One main drawback, however, is related to the micro-porosity of the deposed layer, negatively affecting the corrosion barrier performance. In this paper, the effect of selective laser post-treatment on pure grade 2 titanium coatings on AA2020-T3 sheets was experimentally and numerically investigated. Morphological features, microstructure and chemical composition of the treated zone were assessed by means of optical microscopy, scanning electron microscopy and energy dispersive X-ray spectrometry. Microhardness measurements were also carried out to evaluate the mechanical properties of the treated coating. A numerical model of the laser treatment, based on a finite volume scheme, was implemented and solved to simulate the process and discuss the experimental outcomes. Obtained results highlighted the key role played by heat input and dimensional features on the effectiveness of the treatment.

Jan 1, 2015

By C. Karpuz, Y. S. Istanbulluoglu

This paper describes the results of convergence measurements conducted about five years for the re-use gate roadways at OAL lignite mine in Turkey. Double lignite seams separated with a marn layer, are mined with long-wall retreating mining system at the mine. Rib pillar has been abandoned and gate roadways were planned to be packed for the re-use of full extraction. Various packing systems have been attempted, namely three rows of woodenchock, one row of wooden chock plus concrete wall and concrete wall only. The re-use of maingate roadways packed with wooden chock yielded 62% of closure. Lastly developed concrete packing of 3 meters wide and specially developed support set composed of three friction props and a cap, which is a modification of yieldable set, have successfully maintained the main and tail gate roadways stability with a total vertical convergence of 32%. Good correlation has been established between pack stiffness and floor heave as well as maingate and tailgate convergences. The elimination of rib pillars by re-use of gate roadways increased the coal recovery by 20% and decreased the development/production ratio from 0.065 m3/ton to0.022 m3/ton.

Jan 1, 1997

By S. M. C. Santos

Preliminary bench-scale studies were carried out on the leaching of a zinc sulphide concentrate from Somincor, Portugal, and the purification of the resulting pregnant solution using solvent extraction techniques. The sulphide concentrate contained 36% Zn, 36% S, 2% Fe and 4% Cu. The leaching was carried out with sulphuric acid in the presence of ferric sulphate as the oxidant. Important leaching parameters, such as the effect of reaction time, the solid-liquid ratio, temperature and concentrations of acid and oxidant, were investigated. After leaching, the recovered solution was contacted with an organic phase containing Acorga 5640 to remove the copper. Subsequently, the removal of iron from the leaching solution was achieved with a mixture of Cyanex 272 and TBP. This solvent mixture was relatively selective for iron over zinc. The stripping of the loaded solvent was performed with 200 g/L H2SO4. Six countercurrent extraction stages achieved a separation of about 99% of the iron from the leaching solution. The iron-free leachate can be further treated to recover minor metals by cementation, and finally, zinc by liquid-liquid extraction. The advantages of the suggested process relative to the traditional jarosite process are discussed.

Jan 1, 2006

By G. Ozbayoglu, Z. Ozdemir

Turkey is the main boron minerals producing country in the world. The most important boron minerals are tincal, colemanite and ulexite. All mining, beneficiation and handling operations generate fines which cause ecological and economical problems. Utilization of this accumulated material requires both upgrading and agglomeration. The aim of this research was to exploit the ulexite fines by improving their grade and size. Attrition-scrubbing followed by washing and screening was employed for upgrading the fines. It was found that the grade can be increased from 23-25% B2O3 to 29% B2O3 with 73% recovery. Briquetting was applied as the size enlargement process. During the briquetting, the effect of moisture content, pressure, amount and type of binder, and drying on the quality of briquettes were investigated. The tests showed the possibility of production of strong briquettes by adding water alone, but the briquettes had no resistance to abrasion and water. Binders, namely boric acid and borax have been added to improve the properties of briquettes. The results showed that the compressive strengths and abrasive resistances of briquettes obtained with both binders were acceptable. However, the briquettes have no water resistance properties.

Jan 1, 2004

By J M. Gibbs

Craigmont Mines Limited mine 50,000 tons of ore and waste per day from the open pit at Merritt, British Columbia. An electric-powered "down-the-hole" drill, a diesel-powered rotary drill and two electric-powered rotary drills have been used. All primary drilling, as a result of cost and operating experience, is now performed with two electric-powered rotary drills. Trials with various loading techniques have increased the amount of AN-FO and decreased the amount of commercially prepared slurries used for primary blasting. Approximately 95 per cent of the primary blasting is accomplished with AN -FO, mixed at the hole. Introduction THE Craigmont mine is located near the village of Merritt, B.C., 240 miles northeast of Vancouver. The concentrator has been in production since September of 1961. Craigmont is a combined open-pit and underground operation. To date, slightly more than 95 per cent of the mill feed has been mined from the open pit. As underground development proceeds, the ore requirements from the open pit will decrease. The average milling rate from September, 1961, to April, 1964, was approximately 4,900 tons per day.

Jan 1, 1965

By Jim Dodd, Jim Paynter

"We would like to acknowledge the efforts of the following key people who helped to make this project a success.Ron Jung, instrumentation supervisor for the Golden Giant Mine, spent many hours reviewing process and instrument drawings, selecting instruments and providing hands on support during commissioning.Andy Keough, underground production supervisor for the Golden Giant Mine, was responsible for readying the underground distribution network for paste backfill.H.A. Simons Ltd. personnel who did an excellent job providing sound conceptual and detailed engineering.Fred Brackebusch, of Mine System Design who designed the paste backfill delivery systemPierre Lacombe, mill superintendent of the Louvicourt Mine, generously shared information and operating experience of their paste backfill plant.AbstractThroughout the 11 year history of the Golden Giant Mine, the primary backfilling method made use of consolidated rock fill. New backfill technologies have developed over recent years which now make it possible to use large quantities of fine mill tailings as backfill.In January of 1996, construction began on a new paste backfill plant at the Golden Giant Mine. Six months following, the plant was commissioned. This paper describes the design, commissioning and operational experience to date of the paste backfill plant."

Jan 1, 1997

By J. R. Morris

"A hoisting plant design should satisfy two basic requirements:1. to provide the necessary materials handling capacity, including ventilation where applicable, while meeting the requirements of good practice and, as a minimum, government regulation; and2. to optimize the economics of the project. Selection of hoisting equipment to meet the first objective is a complex but logical engineering process. The necessary calculations of payloads, accelerations, speeds, rope strength, hoist size, and power requirements are very readily carried out on computers or programmable calculators. A variety of hoist options can be quickly examined to assess the effects of changes in design parameters.Meeting the second requirement involves balancing the costs of various hoist arrangements and shaft designs, together with the time cost effects of differing shaft sinking rates and potential advances to be gained by concurrent level development. The proposed mine layout is significant here, as is the possibility of future shaft deepening and/or production increase. The availability of used equipment may be significant, both as regards first cost and delivery time. The factors are interactive, with their relative effects .varying from project to project. This paper sets out the primary factors to be considered."

Jan 1, 1990

By G. P. Cooper

A comprehensive computational heap leach model was used to evaluate options for operating a chalcocite-ore heap leach process. The stockpile leach model is based on the computational fluid dynamic software framework PHYSICA+ and incorporates various physical and chemical phenomena to simulate fluid transport, mineral reaction kinetics, bacterial effects, and heat, energy and acid balances for the overall leach process. The leach model is calibrated against small-scale column leach tests, and simulation results are validated against closely controlled column pilot-scale tests. For a given set of ore conditions, the effects of raffinate irrigation rate are examined. Several options for pulse leaching were investigated, and the effects on copper recovery and pregnant leach solution (PLS) grade are described. Model simulations indicated that pulse leaching could be used to control copper grade of the PLS. Finally, an analysis of inventory issues is presented for various lift heights including multi-lift simulations to examine potential operating options. U sing irrigation rate, raffinate copper grade, and lift height as variables in a factorial design of experiments, the simulations showed that raffinate copper grade is the main factor that affects the soluble copper inventory grade.

Jan 1, 2007

By Jean-François Doyon

Les aspects environnementaux des activités minières d?exploitation réalisées sur le territoire québécois sont encadrés par divers cadres légaux, réglementaires ou autres (directive, politique, guide) tant au niveau provincial que fédéral. Ces cadres s?appliquent à l?un ou l?autre des trois grandes étapes du projet, soit lors de l?étude d?avant projet, pendant l?exploitation ou à la cessation des activités d?exploitation. Comme la réglementation environnementale est de plus en plus nombreuse, ces dernières années, cette présentation vise à exposer les principaux cadres provinciaux et fédéraux actuellement en application au Québec pour le secteur minier et à en dégager les particularités. ABSTRACT The environmental aspects of mining activities carried out across Quebec fall within the scope of various legal, prescribed or other frameworks (directives, policies, guides) at provincial and federal levels. These frameworks apply to one or another of the three major steps of a project: preliminary design, mining and closure. As the number of environmental regulations has greatly increased during the past few years, the object of this presentation is to state the main provincial and federal frameworks currently applicable in Quebec for the mining sector and to identify their special features.

Nov 1, 2002

By Michio Okada

Dissociative adsorption of hydrogen (deuterium) on thin gold films grown on Ir{111} surface has been studied with temperature-programmed desorption using a quadrupole mass spectrometer and nuclear reaction analysis. Thin Au{111} films are epitaxially grown on Ir{111}. Surprisingly, H2 (D2) can dissociatively adsorb on these Au{111} films, although it is well known that Au surfaces are noble enough not to dissociate hydrogen molecules [B. Hammer and J.K. Nørskov, Nature 376, (1995) 238]. We attribute this to the sensitivity of hydrogen to changes in the local surface properties, e.g., electron localization (the narrowing of the s-band, the s-band center model), which could explain the upto now unexpected high for the reactivity of a thin Au{111} surface. Moreover, we found that H (D) atoms can be confined into a Au thin film and/or the interface between an Ir surface and the thin Au film. We demonstrate how anomalously reactive thin Au films grown on an Ir surface are, and also compare the Au films with Ag films grown on Ir to test the validity/generality of our proposed s-band center model.

Oct 1, 2003

By Edmond Chow

Shovel bucket blast fragmentation analysis is an alternate way to assess blast performance and its effects on downstream mining processes. A camera is installed on the boom of cable shovels, and the stick of hydraulic shovels. Images are captured automatically as the shovel digs, and are processed to acquire rock size information. The automatic data acquisition makes this method safe to use with minimal manual labour. It also allows for a large set of sample data to be captured from both the surface and the interior of a bench face. The system has been deployed in several mines to provide an objective assessment of blasting performance. Images are captured from their cable or hydraulic shovels. The images are grouped into sets based on the shovel location and time to match the fragmentation to specific blasts. Blast fragmentation reports are created for each blast after reviewing the results. Measuring blast fragmentation from the shovel bucket proves to be an effective alternative for blast performance assessment with unique advantages. The blast fragmentation information has been valuable to the mines, and the mines have begun adopting it into their operations.

May 1, 2011

By Zhongxue Li

This paper reviews an analytical model that defines the relationship of weight-weighted or volume-weighted average haulage distance with bench height and other related parameters, presents the optimum bench heights under various conditions in terms of minimizing the weighted average haulage distance of ore/waste during the full lifetime of an open pit mine, and discusses the truck haulage economics of mining open pits by high bench, specifically by 15 m, 18 m and 20 m benches through marginal analyses. The observations from these analyses disapprove the previous conflicting assertions that the over-all weighted average haulage distance either increases or decreases directly with bench height. It is concluded that: (1) an increase of bench height to 15 m from 12 m is likely to be viable under the general conditions of large-scale deep open pit mines; (2) the reduction of haulage cost is much limited with the case of increasing bench height to 18 m from 15 m; and (3) the feasibility of mining open pits by 20 m benches is generally questionable. These conclusions may serve as a useful guide for those who advocate open pit mining by high bench.

Jan 1, 1995

By S. Esfahani, M. Barati, K. Danaei

"Substituting Portland cement with slag cement is one of the most economically attractive uses of slags. For this application, high cooling rates are required to form an amorphous structure. However, this is counteracted by the need to use small coolant flowrate to allow recovery of slag thermal energy as high quality heat to the coolant fluid. Therefore, a relationship between cooling rate of slag and its structure is essential to recover the heat effectively while making an amorphous slag.A modified Single Hot Thermocouple Technique (SHTT) was employed to investigate the crystallization behavior of slags by plotting their TTT (Time-Temperature, Transformation) diagrams. Seven different slag compositions containing CaO, SiO2, Al2O3, MgO were prepared at varying basicity (CaO/SiO2 =0.5-1.4).The results indicate that with increasing basicity, the TTT curves of glassy to crystalline transformation shift to the left which means higher crystallization tendency. This agrees with the fact that with the increase of basicity, the Si-O bonds are weakened, which in turn facilitates the re-ordering and crystallization of the silicate structure."

Jan 1, 2014

By D. W. Euler, B. J. Clauzier

"Implementation of an effective energy management system will reduce energy costs without impacting negatively on production.The energy management system must be designed to complement the operation and be integrated with the organization. It must be reliable and easy to use but most important, it must have an accurate and timely feedback reporting system to allow the operation to take appropriate action.Falconbridge Limited was one of the first three companies to be awarded the energy monitoring demonstration program in May 1987. The program is sponsored jointly by the Ontario Ministry of Energy and Ontario Hydro.This paper describes the approach taken by Falconbridge Limited to implement the Onaping Area Energy Management System.IntroductionThe objective of the project was to implement an effective energy management system, capable of reducing energy costs without impacting negatively on production.Energy management systems must be designed to complement the operation and to be integrated with the organization. The system must be reliable and easy to use, but most importantly, it must have an accurate and timely feedback reporting system to allow the operation to take appropriate action."

Jan 1, 1990

The North Saskatchewan River flows southwest to northeast through a 22-km-long valley in the City of Edmonton, supplying the drinking water to dozens of downstream communities. During heavy rains, combined sewers occasionally overflow into the river, which has a significant negative impact on the water quality and the sensitive environment. The West Edmonton Sanitary Sewer (WESS) W12, a syphon connecting the Rat Creek Trunk to the Gold Bar Wastewater Treatment Plant across the river, was designed and constructed to take the overflow to the wastewater treatment plant. Due to the complexity of the project, various 3D technologies were applied to facilitate decision-making processes. 3D models were developed for design review and design conflict detection, while 4D models were established to help create a robust construction schedule. Construction sequencing animation was used to convey design intents and demonstrate construction stages to contractors and workers. The combined applications of 3D technologies helped the project team to identify critical issues, and assured effective communication among engineers, management, contractors, and other parties. Therefore, it provided more opportunities for the success of the project.

Aug 1, 2013

By P. Rosario

"Industry practice for high-pressure grinding roll (HPGR) assessment and sizing relies on tests using pilot-scale machines with 0.7–1.0 m roll diameters. Typically 1–10 t of sample are required, depending on the level of study and resource complexity. This is challenging during early-stage development, which hinders incorporating HPGR into designs. With support from the Canadian Mining Industry Research Organization, researchers at the Norman B. Keevil Institute of Mining Engineering at The University of British Columbia developed bench-scale piston–die press tests (PPTs) that correlate to pilot- and full-scale HPGRs. This paper describes a new regression model to estimate the HPGR-specific throughput rate using both PPT results and an HPGR database. A case study is presented to show how the current PPT method is used for engineering studies. ¦ KEYWORDS Empirical modelling, High-pressure grinding roll (HPGR), Piston–die press test (PPT), Sizing and scale upRÉSUMÉ La pratique en vigueur dans l’industrie concernant l’évaluation et le calibrage d’un cylindre de broyage à haute pression (HPGR, de l’anglais high-pressure grinding roll) dépend d’essais menés à l’aide de machines à l’échelle pilote dont les diamètres de bobine sont de 0,7 à 0,10 mètre. On a généralement besoin de 1 à 10 tonnes d’échantillons en fonction du niveau de complexité de l’étude et des ressources. C’est une pratique difficile durant les premières phases de développement, qui empêche l’intégration du HPGR dans les plans. Bénéficiant du soutien de la Canadian Mining Industry Research Organization (CAMIRO, l’organisation de recherche de l’industrie minière canadienne), des chercheurs du Norman B. Keevil Institute of Mining Engineering (l’institut Norman B. Keevil de génie minier) de l’université de la Colombie-Britannique (UBC) ont mis au point des essais en laboratoire sur des presses à matricer à pis¬ton (PPT, de l’anglais piston–die press tests), qui mettent en corrélation les HPGR aux échelles pilote et réelle. Cet article décrit un nouveau modèle de régression qui évalue le taux de production spécifique aux HPGR à l’aide des résultats tirés des PPT et d’une base de données dédiée aux HPGR. Une étude de cas est présentée afin de décrire l’utilisation de la méthode actuelle des PPT dans les études techniques. ¦ MOTS CLÉS calibrage et mise à l’échelle, cylindre de broyage à haute pression (HPGR), essai sur presses à matricer à piston (PPT), modélisation empiriqueINTRODUCTION It is widely accepted that high-pressure grinding rolls (HPGRs) are a viable, energy-efficient solution for modern comminution flowsheet design. Table 1 summarizes select examples of HPGR applications in the mining industry. The main benefits of HPGRs are energy savings, which leads to lower operating costs, and stable operating characteristics that can better cope with variations in ore hardness compared to the conventional autogenous (AG) or semi-autogenous (SAG) mill-based comminution circuits."

Jan 1, 2019

Inco Limited has been evaluating options for streamlining the overall flowsheet at its Sudbury, Ontario operations to improve productivity and to minimize the cost of at¬mospheric emissions reduction. Some of the flowsheets being considered include vari¬ous levels of copper/nickel separation at the Clarabelle Mill where all Inco's Sudbury Basin ores are processed. This paper reports on the laboratory and miniplant studies car¬ried out during the flowsheet development for a commercial Cu/Ni separation plant. There are two potential feed streams for Cu/Ni separation. It was determined that Cu/Ni separation from the rougher concentrate requires no regrind, and a very clean copper concentrate is produced, but the recovery of copper is limited to about 70% from ore. Cu/Ni separation is more difficult from the bulk concentrate because of the presence of excess flotation reagents in the slurry and due to locked particles. By replacing the slurry water with clean process water, and by addition of some hydrogen peroxide, entrainment is minimized and excess reagents are removed from the surface, providing a satisfactory separation of copper from nickel. Fine regrinding is required to increase liberation of the locked particles and to obtain 85% copper recovery with minimal nickel contamination of the concentrate.

Jan 1, 2005

By M. Cala

Underground coal gasification is technology which enables energy to be extracted from coal beds where mining by means of classical methods is either impossible or uneconomical. The process of coal gasification itself is a complex phenomenon which includes chemical and physical processes: thermal, hydrological and mechanical. Additionally, the analysis of underground coal gasification is difficult to carry out for environment reasons, this being due to the local characteristics of the areas where it is carried out. This paper deals with interaction of geo-reactor with surrounding rock mass, it omits the chemical processes inside geo-reactor itself. Due to the complexity of the processes proceeding and during underground coal gasification coupled with minimal practical experience in using this technology, it is difficult to estimate its influence on the surrounding rock mass. Within this scope, the use of numerical programs can be useful. This paper presents a trial of modeling the processes accompanying underground coal gasification. The processes proceeding and during the underground coal gasification are characterized, and the significant, specific phenomena are discussed, with respect to the influence on the surrounding rock mass. For the chosen processes, examples of numerical calculations are presented. These enabled conclusions to be drawn and also provided directions for the modeling of the underground coal gasification processes.

Aug 1, 2013

By B. Arlyuk

On the basis of research of relations among the market participants the analytical model has been created which connects the price of industrial good at stock exchange with volume of sales and the stock of the sellers and buyers, Also a model was developed for assessment of these parameters of the market status by the actually fixed stock exchange and general market indicators. The composition of these models made it possible to create reliable system of short-term price forecasting for commodities or base metals up to one quarter ahead. Imperfectability of creation a model for reliable price forecasting by purely statistic methods (by the "black box" principle) was shown. A model of price behavior qualitative forecasting till one quarter ahead has been developed, which determines the probability of reaching in future of the given level as well as of the price maximums and minimums, Optimal values of threshold probability were determined for forecasting the future price maximums and minimums securing the maximum profit from the forecasting system application for commercial activity. The developed system of forecasting was identified for primary aluminium at the period of 1990-2003. The system was tested daily during 20 months period for speculations on 3M primary aluminium forwards at London Metal Exchange with high commercial result.

Jan 1, 2004

By P. Groleau, O. Tavchandjian, D. Marcotte

In open pit mining, each small mining unit (SMU) is selected for mill processing based on an estimate of its true grade. The estimation is usually done using analyses of cuttings from blast holes within that SMU. One common estimator used for selection is the arithmetic average of within-SMU samples. This estimator is conditionally biased. The effect of a conditional bias is to overestimate the profit really recovered from the deposit. For this reason, a conditionally unbiased estimator is preferable. Increasing the number of samples generally improves the accuracy of the estimation (and diminishes the conditional bias, if present, of most estimators). However, there exists a practical limit where an additional sample does not improve the estimation sufficiently to cover the expense of making the analysis. This limit is specific to each deposit and depends on geostatistical parameters, economic factors, and mining parameters. This study examines how the number of samples affects the recovered reserves and the resulting profit. Also, the effects on optimal profit of varying the different factors are examined. Globally, the number of samples required increases with the selectivity of the operation. For a given ore deposit, the greater the number of SMUs selected for processing, the fewer samples are required and vice-versa.

Jan 1, 1998