Search Documents

By Chen Bang, Xia Xiao’ou, Zhang Feng

"Ores with compressive strength lower than 150 MPa are usually easy to be crushed by conventional jaw crushers and cone crushers. However, for hard ores with compressive strength exceeding 150 MPa and 200 MPa and even up to 250 MPa, such as andesite, hard basalt and olivine, it is difficult to reach satisfactory crushing size and yield or difficult to meet service life and stability use requirements of quick-wear parts by using conventional crushers. As continued increase in ore mining depth and constant generation of new type materials, equipment demand for crushing hard ores becomes increasing high. A new type inertia vibrating crusher is designed. It is powered by a high-speed rotating vibration exciter and can obtain required crushing force by adjusting eccentric mass, eccentricity and rotating speed so as to crush various ores with high hardness. This paper introduces the design process of its structure and working principle, discusses the design calculation methods of vibration excitation system, vibration damping and energy storage system and other key mechanism and provides technical references for this type of vibrating crusher.DESIGN PHILOSOPHYThe conventional jaw crusher mainly acquires extrusion force from crank motion to realize crushing. The motor drives the eccentric shaft via the transmission device to bring the moving jaw to swing relative to the stationary jaw. When the moving jaw moves close to the stationary jaw, ores between them are crushed by extrusion; when the moving jaw moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving jaw and the stationary jaw.The conventional spring cone crusher and the hydraulic cone crusher mainly acquire extrusion force from cranking motion to realize crushing. The motor drives the eccentric sleeve via the transmission device, the moving cone shaft generates an eccentric distance to make cranking motion under the action of the eccentric sleeve. When the moving cone moves close to the stationary cone, ores between them are crushed by extrusion. When the moving cone moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving cone and the stationary cone under the action of dead weight."

Jan 1, 2016

By J. Ramirez-Castro, J. A. Finch

"Galena is the finest component of the product of a closed-circuit grind treating a lead-zinc ore, largely due to preferential recycling of this high-density mineral by the cyclone. For example, at the Pine Point Mines concentrator, for ~ 55% -200 mesh over-all, the galena will be close to 95% -200 mesh. This sliming of the lead can limit recovery, selectivity and dewatering. A proposed circuit modification to reduce the sliming is to incorporate a unit cell. A simulator was constructed to study the No. 3 grinding circuit at Pine Point modified by a unit cell on ball mill discharge (BMD).The simulator used a cumulative size basis rate-of-breakage with plug flow ball mill model, the parameters being obtained by laboratory grinding tests. Flotation and the cyclone models used a cumulative recovery/size matrix. The behaviour of each mineral, galena, sphalerite, pyrite and calcite/dolomite, was simulated. Simulation was adapted to a programmable calculator. A close fit to the existing circuit performance at two tonnages and mineral mixes was established.The simulator showed that the modified circuit could significantly coarsen the Pb grind, from 95% to —50% -200 mesh, depending on recovery, without substantially altering the size of the other minerals. The other principal findings were: compared to laboratory flotation tests on existing circuit BMD, the unit cell concentrate (CONC) will be coarser and markedly lower in grade; relatively low unit cell stage recoveries are desirable, because the cyclone scavenges the tail to give a circuit recovery which is higher than the unit cell stage recovery; unit cell stage recovery should not exceed the cyclone stage recovery, as the latter is the maximum circuit recovery; low unit cell stage recovery helps offset the disadvantage of the high flow at BMD; other high-density minerals will also be scavenged into the CONC, as illustrated by pyrite, making CONC quality difficult to maintain; density control of BMD flotation does not greatly alter feed density to the cyclone or ball mill.Possible plant metallurgy is forecast for a CONC diverted to final lead concentrate."

Jan 1, 1980

Presentation Outline Introduction Deposit Characteristics Geology Grade, Value and Tonnage Estimates 2006 Advanced Program Drilling Bulk Sampling DMS Test Facility 2006 Exploration Summary

May 1, 2006

Mining Subscribes to Murphy?s Law Personal observations on the past ?Perfect, benign deposit mines can be screwed up-spills and concentrate handling issues ?Long term contamination and water management assessments inadequate ?The ?permitting mentality? and its effects on the application of proponent and regulator resources ?Reliance on simple principles but nature and chemistry is more complex

May 1, 2010

By Paul Girodo

Government Approval For Foreign Workers 1.Service Canada Work Permit Tasks: i. Prove there are no Canadian Journeymen; ii. Use heavyweight stakeholders; iii. Understand the FWU transformation taking place today. Government Approval For Foreign Workers 2.Provincial Nominee Program (PNP) i. Build relationships; ii. Use heavyweight stakeholders; iii. Continually demonstrate benefits to the Province from foreign Journeymen. Government Approval For Foreign Workers 3.Letter from Union Supporting Temporary Foreign Workers i. Easiest path to approval ?CLAC model

May 1, 2006

By P. Strand

Talk Outline ? Location and Regional Geology ? Two Unique Kimberlite Sources ? Mineral Chemistry ? Petrography, Age Dates ? Geophysics ? Exploration and Challenges ? Dyke versus Pipe dispersions ? Geophysics ? Prospecting ? Diamond Results ? Summary & Conclusions

May 1, 2008

By Bernard Vigneault

Les critères de qualité de l?eau pour les métaux visant à protéger la vie aquatique sont présentement basés sur les concentrations totales. Cependant, la complexation (association de ces métaux avec des ligands en solution) peut diminuer de façon importante la toxicité des métaux sur les organismes aquatiques. Pour évaluer l?importance de la complexation pour diminuer la toxicité des métaux dans les effluents miniers et métallurgiques, nous avons étudié la spéciation des métaux et la toxicité chronique de différents effluents miniers et métallurgiques. La phase dissoute des effluents a été échantillonnée à l?aide de la dialyse in situ et la spéciation du cuivre, du zinc et du cadmium a été calculée à l?aide du modèle d?équilibre chimique WHAM. Les concentrations de métaux libres ont également été mesurées à l?aide d?une technique d?échange ionique. Les concentrations de métaux libres calculés et mesurés indiquent que la complexation est importante dans les effluents miniers, particulièrement pour le Cu. Pour relier la spéciation des métaux et la toxicité chronique, nous avons mesuré en parallèle l?inhibition de croissance de l?algue Selenastrum capricornutum et des larves du poisson Pimephales promelas de même que l?inhibition de la reproduction du cladocère Ceriodaphnia dubia. (tests de toxicité chronique inclus dans le programme de suivi des effets environnementaux du règlement fédéral sur les effluents de mines de métaux). En absence de thiosels, aucune mortalité a été observée pour l?ensemble de ces tests et il n?y a pas eu également d?inhibition la croissance de la larve de poisson P. promelas. L?inhibition de la croissance de l?algue S. capricornutum, n?est pas reliée aux concentrations de métaux traces mais plutôt par aux concentrations de calcium. Les inhibitions de la reproduction du cladocère C. dubia sont reliées aux concentrations de métaux dissoutes et libres et non pas aux concentrations totales de métaux, démontrant l?importance des effets de la spéciation chimique sur la toxicité des métaux. Nos résultats indiquent que l?inhibition de la croissance de l?algue l?algue S. capricornutum est due aux concentrations élevées de calcium retrouvées dans les effluents miniers et que les concentrations totales de métaux ne peuvent être utilisées pour prédire la toxicité chronique vis à vis le cladocère C. dubia.

Nov 1, 2002

By Patrick Andrieux

Numerous rock blasting design methodologies have been developed over the years, relating either to the primary objectives of blasting, such as the size distribution of the blasted material, or to its undesirable side effects, such as damage to the remaining rock mass. All existing methodologies, while of use, do have serious shortcomings. The question remains whether further improvements can be achieved in the field of practical rock blasting engineering. One approach that seems to hold promise is the relatively new matrix-based rock engineering systems (RES) methodology. It has been conceptually demonstrated that RES could be efficiently adapted to blasting. A brief overview of rock blasting design techniques and their main shortcomings is followed by the basic concepts governing rock engineering systems and a discussion on their pertinence to blasting. The paper concludes with a review of current efforts to develop a useful practical blast design tool using RES. SOMMAIRE Le potentiel d?application des systèmes d?ingénierie du roc aux tirs à l?explosif. De nombreuses méthodologies de conception d?abattage du roc à l?explosif ont été développées au cours des années, qui ont adressé soit les principaux objectifs des tirs, comme par exemple la granulométrie du matériel dynamité, soit ses effets secondaires indésirables, tels les dommages au massif rocheux. Toutes les méthodes existantes fonctionnent dans une certaine mesure et sont utiles - elles sont cependant pour ainsi dire toutes affectées par des limitations ou défauts plus ou moins sévères. La question demeure quant à savoir si des améliorations supplémentaires peuvent être apportées dans le domaine de la conception pratique des opérations d?abattage du roc à l?explosif. Une approche alternative qui semble prometteuse est celle relativement récente des systèmes matriciels d?ingénierie du roc (?Rock Engineering Systems?, ou RES). Il a été démontré de manière conceptuelle que les RES ont le potentiel d?être adaptés aux opérations de sautage. Une brêve revue des principales techniques de conception des tirs à l?explosif est suivie d?un énoncé des principes de base gouvernant les RES, ainsi que d?une discussion sur leur pertinence aux opérations de tir. Cet article conclut avec la revue d?un projet de recherche axé vers le développement d?une méthodologie de conception des tirs à l?explosif basée sur les RES.

May 1, 2002

By Euler M. De Souza

"This paper presents a study developed to assess the potential use of salt tailings as backfill to control surface subsidence and as a mine bulkhead used to isolate areas of potential brine inflows. A series of index tests, centrifuge model tests and quasi-static creep consolidation tests were performed to evaluate the creep and consolidation properties of salt backfl1l and to evaluate the effect of brine inflow and brine infiltration on backfill behaviour. The centrifuge models were specifically designed to study the mechanical behaviour of salt backfill under the influence of brine inflow and long-term creep. Test results indicated that salt tailings could be applied underground as a bulkhead to seal off areas of potential inflow with the additional advantage of controlling room closure and local back instability. It is hoped that this study will assist mine planners to develop contingency plans to control brine inflow occurrences. IntroductionThe use of salt tailings as backfill is a technique that would assist in the control of potential brine inflows and surface subsidence, and would have a very positive impact on the long term adverse environmental effects associated with surface salt tailings disposal. A centrifuge testing program was designed to evaluate the behaviour of salt tailings as backfill; the effectiveness of salt backfill as a bulkhead used to isolate areas of potential brine inflow and the potential use of salt backfill to control surface subsidence. The testing program was also used to evaluate the creep-consolidation properties of salt backfill and to evaluate the effect of brine inflow and brine infiltration on backfill behaviour. This paper presents the results of the experimental centrifuge testing program and a comparison of results with models tested under I g using an electrohydraulic servo-controlled loading frame (MTS) and a creep consolidation cell. Applicability of the results to practical underground soft rock mining is also discussed.The centrifuge model tests indicated that salt tailings could be applied underground as bulkheads to seal off areas of potential inflow with the additional advantage of controlling room closure and local back instability. Because the applied stresses (1.2 MPa) and fill consolidation were relatively low, the centrifuge simulated bulkhead did not retain all of the inflow brine. At typical field stresses it is expected that the fill would be able to seal off panels with brine inflows. Further testing at higher stresses are suggested to determine the consolidation and stress levels at which the fill would completely retain any potential brine inflow head and positively act as mine bulkhead."

Jan 1, 1994

By W. Lamb

Feed Preparation ? Five primary parameters affect the screening efficiency ? Ore characteristics ? Operational characteristics ? Screen characteristics ? Water addition and washing ? System design

Apr 1, 2005

By Lawrence Devon Smith

The Business Case for Sustainable Development ?What are SD & TBL? ?Investment Funds & Fund Managers ?Banks and Risk Aversion ?The Dilemma of Juniors ?Meet Your New Partners ?The Cost of Problems ?The Cost of Delays Sustainable Development ?Humanity has the ability to make development sustainable -to ensure that it meets the needs of the present without compromising the ability of future generations to meet their own needs.? Our Common Future BrundtlandCommission, 1987

May 1, 2003

By J. Kang

There is increasing demand to utilize aluminium alloy sheets and their spot welds by the automotive industry. While traditional uniaxial tensile tests only determine mechanical properties to small strain, direct measurement of the constitutive behaviour of aluminium alloy spot welds at large strain remains a challenge. A technique was successfully developed using digital image correlation coupled with shear tests to directly measure the constitutive behaviour of an AA6022-T4 spot weld to large strains. The results show that the spot welding process not only decreases the yield strength but also lowers the work hardening rate of the nugget versus the base material. Details of sample preparation, experimental approach and results will be discussed.

Jan 1, 2011

By Sadough vanini Ali

Hot deformation behavior of functionally graded steel (FGS) was investigated via conducting hot compression tests at different temperatures and strain rates. Functionally graded steels consist of ferrite, austenite, bainite and martensite layers that are made by diffusion of alloy elements during the melting process. The zenerhollomon parameter has been used to describe the flow stress variations as a function of temperatures and strain rates. The parameter values for all the layers via using the boundary conditions was determined based on composite graded behaviors. Furthermore by applying the rule of phase mixtures, the whole strain rate applied on composite would be the sum of layers strain rates considering the layers volume fraction, while the layers have the same stress. Consequently the composite flow stress for each strain rate and temperature was determined.

Oct 1, 2011

By Steven Dempsey

Overview What is Tubbing? A look at Cigar Lake Tubbing Design The Tubbing Installation Backwall Grouting

May 1, 2013

By Kenneth Williamson

La découverte de nouveaux gisements métallifères constitue le point de départ du développement de l'industrie minérale. Or, au cours de ces dernières années, le nombre de ces découvertes a fortement diminué dans les territoires classiquement explorés, entraînant une recrudescence de l?exploration dans les terrains géologiques de grade métamorphique élevé (e.g., Province de Grenville, Grand Nord du Québec). Ces derniers ont été traditionnellement considérés comme stériles à cause (i) de la monotonie apparente des gneiss qui les composent, (ii) de la difficulté d?identifier leurs protolites, (iii) des changements importants dans l?apparence des gîtes recherchés reliés au fort degré de déformation et de métamorphisme et (iv) des théories qui prônent un lessivage important des cations et des métaux d?intérêt économique par les processus de déshydratation des roches lors du métamorphisme régional (Weaver et Tarney, 1985; Vokes, 2000). Cependant, l?avancée des connaissances dans la compréhension des gîtes métallifères et de leurs terrains hôtes gneissiques intensément métamorphisés, montre que les systèmes géochimiques des roches altérées demeurent robustes (p. ex. ; Trägårdh, 1991; Craig et Vokes, 1993; Geringer et al., 1994; Schandl et al., 1995; Zaleski et Peterson, 1995; Vokes, 2000; Blein et al., 2003, sous presse). Bien sûr, les sulfures peuvent être localement remobilisés et même fondre, mais cette remobilisation n?implique pas forcément la disparition du gîte hôte (Williams, 1990) et peut s?avérer, bien au contraire, bénéfique pour la rentabilité d?un gîte en augmentant sa teneur en minerais (Marshall et al., 2000). Jusqu?à présent, dans les terrains métamorphiques, les contextes sédimentaires et plutoniques ont été reconnus et respectivement explorés pour les gîtes de type SEDEX et les gîtes magmatiques de Ni-Cu. L?étude de gîtes de métaux de base et précieux intensément métamorphisés (faciès des granulites) et leur comparaison avec des gîtes équivalents peu on non métamorphisés a permis d?établir, au cours des dernières décennies, des outils pour l?exploration des terrains de haut-grade métamorphique (Vokes, 1991, 2000; Slack et al., 1993; Spry et al., 2000). Ces outils sont basés sur la reconnaissance de roches diagnostiques d?une circulation ou d?une exhalation de fluides hydrothermaux telles que les méta-exhalites (formation de fer, coticules, tourmalinites, roches riches en quartz-gahnite, en apatite, en barite ou en staurolite zincifère) (Spry, 2000; Spry et al., 2000). Ils sont utilisés constamment dans les ceintures supracrustales riches en roches métasédimentaires.

May 1, 2003

? Introduction ? Partenariat MRNF - MAE ? Goldex ? Manitou : - Ré-aménagement du bassin versant - Accès aux zones problématiques - Filtration du ruisseau pour les travaux - Nettoyage près de la rivière - Régulation du débit et bassin - Digues et bassins - Déposition résidus Goldex ? Chemins d?accès Goldex-Manitou ? Pipelines: Goldex ? Retour Goldex ? Manitou ? Station de pompage ? Résumé

Feb 1, 2008

By R. E. Baylis, M. R. Tolley, S. Singh, A. J. Murray, R. Boden, L. E. Macaskie, T. P. Hathway, D. Vavlekas

We report rare earth element (REE) recovery using immobilized Serratia biofilm depositing metal phosphate via a robust enzymatic mechanism. Activity was approximately halved at pH 3.5 and restored at pH 5.5. REE(III) was recovered selectively against Th(IV) but the method was non-selective between different REEs (La, Y, Eu, Nd). Biofilms were active for a year (half life of ~ 3 months). The activity of aged biofilm was enhanced by pre-nucleation (‘priming’) with NdPO4 prior to onset of flow-through conditions. The use of different ‘priming’ metals and bacteria via a combinatorial approach revealed some REE selectivity through the selective exclusion of specific REEs.

Jan 1, 2014

By Yufeng Yao, Robert P. Lowell

Abstract - Conductive heat flow anomalies associated with hydrothermal sulfide mounds on the seafloor have been studied. Sulfide mounds tend to focus conductive heat flow because sulfide minerals have a greater thermal conductivity than country rock. The topography of the mound above the seafloor, however, leads to a reduction of heat flow, particularly near the center of the mound. Because the focusing effect is constant, whereas the topographic effect decreases with distance away from the center, the focusing effect dominates toward the edges of the mound. The magnitude of these effects depends upon the conductivity contrast and the height/radius aspect ratio of the mound. Conductive heat flow anomalies at sulfide mounds also result from fluid circulation within the edifice. For the active and relict mounds at the TAG hydrothermal field, which have an aspect ratio of approximately 0.3 and a conductivity contrast of 3, the heat flux through the center of the mound should be roughly 70% of the background heat flux. The maximum effect of heat flow focusing is to increase the heat flux by about 30% above background. By comparing these effects with conductive heat flow data at TAG, we find that advective processes dominate conductive heat flow at both the active and relict mounds. Advective circulation can also give rise to much larger lateral and vertical temperature gradients than would result from conduction alone.

Jan 1, 1999

By Patrick R. Taylor, T. A. R. Putra

A review of various methods to treat high arsenic copper concentrates through pyrometallurgical processing is presented. Examples are drawn from various past and current operations and research. Various aspects of the engineering alternatives for treatment methods are discussed. Some of the methods discussed include: controlled oxidation roasting, adaptation of some smelter technology to accept higher amounts of arsenic, complete oxidation with arsenic fixation; sulfation roasting; acid baking, soda ash roasting, and others methods. Other topics include: a short discussion of other problematic impurities; the effects of arsenic on copper electro-refining and product purity; and methods for the ultimate disposal, or marketing, of the arsenic. The latest work being done at the Colorado School of Mines on soda ash roasting is also presented.

Jan 1, 2014

Fiabilité Totale d?Usine (FTU) Plan de la présentation ?Théorie de l?entretien ?Analyse comparative juin 2005 ?Session de travail 2005-2006 ?Suiviet Résultats(IndicateursdePerformance)

Feb 1, 2008