Search Documents

By Stephen A. Gasiorowski, Frank J. Hrach, James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity - up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle-particle contact. The small gap, high electric field, counter-current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in North America and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Jan 1, 2012

By B. A. Sparkes, J. H. Reeves

"The St. Lawrence Granite hosts vein-type fluorite mineralization that was mined until 1977. Recent drilling identified a significant fluorite-bearing structure hosted in adjacent meta-sedimentary country rocks. Several phases of vein fill and brecciation indicate there are three phases of fluorite mineralization, of which the later two phases are volumetrically significant. The earliest fluorite is purple and occurs along joint and fracture surfaces, in fault-breccia matrices, and as stockwork veins. The second phase comprises primarily red, yellow, blue-green, and white colours of fluorite. The latest phase is green with lesser clear fluorite. Identification of fluorite veins in the meta-sedimentary rocks opens up new areas for exploration.RÉSUMÉ Le granite St. Lawrence contient une minéralisation filonienne de fluorite, laquelle a été exploitée jusqu’en 1977. De récents forages ont permis d’identifier une structure importante contenant de la fluorite encaissée dans des roches métasédimentaires adjacentes. Les nombreuses phases de remplissage de filons et de formation de brèches indiquent qu’il y a eu trois phases de minéralisation de fluorite et les deux dernières sont importantes d’un point de vue volumétrique. La plus ancienne fluorite est mauve et se trouve le long de surfaces de joints et de fractures, dans les matrices de brèches de failles et en tant que stockwerks filoniens. La deuxième phase comprend surtout des fluorites de couleurs rouge, jaune, bleu-vert et blanc. La fluorite de la plus récente phase est verte avec des quantités moindres de fluorite claire. L’identification des filons de fluorite dans les roches métasédimentaires ouvre de nouveaux secteurs pour l’exploration."

Jan 1, 2016

By K. Ananthanarayanan, R. I. L. Guthrie, S. A. Argyropoulos

"The low cost and availability of micro-computers and their peripherals provides the metallurgical engineer with the opportunity to use such computers in a wide variety of applications. In this paper, the authors describe the development of a low cost data acquisition system capable of measuring up to 8 analogue channels at a sampling rate of up to 5000 measure mentsper second. This system is equipped with proper hardware and software so that the micro-computer can be linked to a central computer facility such as the McGill System for Interactive Computing (MUSIC). This central computer facility is supported by an AMDAHL V7 computer. Using the present interface, communication rates between the microcomputer and the central computing facility can be as high as 9600 (baud).The above mentioned data acquisition system is currently used for monitoring dissolution kinetics of ferro-alloy additions in liquid steel. In addition to this, special software has been developed which enables the user of this system to monitor solidification rates of ingots, etc. As economic considerations are always important, comparisons have been made with existing recorders which show that the cost Of the present system is only 30 per cent more than a two-pen strip chart recorder.RESUMELa disponibilité et le bas prix des micro-ordinateurs et de leurs périphériques permet à l&apos;ingénieur métallurgiste d&apos;utiliser de tels ordinateurs pour diverses applications. Dans ce rapport, les auteurs décrivent le développement d&apos;un système d bas prix pour l&apos;acquisition des données, capable de mesurer jusqu&apos;à huit canaux analogues jusqu’à une vitesse de 5000 mesures par seconde. Ce système est équipe avec son propre ""hardware"" et ""Software"" qui relient le micro-ordinateur d’un ordinateur central, comme le système de McGill pour computations réciproques (MUSIC). Ce central d&apos;ordinateurs est soutenu par l&apos;ordinateur AMDAHL V7. Utilisant cet "" interface"", la vitesse de communication entre Ie micro-ordinateur et l&apos;ordinateur central peut atteindre jusqu&apos;d 9600 (baud)."

Jan 1, 1980

By Rolf A. Knopp

This paper discusses how design differences in FLP diesel equipment in underground coal mines came about. "Design standards" tend to create differences between countries while fostering uniformity among products of competing manufacturers. "Performance requirements," on the other hand, tend to eliminate differences between countries while encouraging competitive development of better products. Examples of regulations from the U.S., Canada. Great Britain. Australia. South Africa, etc., are used to illustrate differences in the design and certification of diesel equipment for underground coal mines.

Jan 1, 1978

By Stefan Wallner, Andreas Filzwieser, Stefan Konetschnik, Reinhard Preiss, Iris Filzwieser

"Process Safety Management for METTOP means avoiding risks as far as possible - but also dealing with the residual risk by using all existing management tools or external assistance, if required. The presented paper has two parts. The first one introduces a new and very safe cooling technology for metallurgical furnaces. The second part shows how to deal with the residual risk as well as minimize it by using the tapping area of an electric arc furnace as an example.Today more and more intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetime, making cooling technology an important aspect of furnace operation. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion.To overcome the disadvantages of water, a new cooling technology using an alternative cooling medium, namely ISIS B (a special kind of ionic liquid) was developed. The main advantage of ISIS B is the fact that no explosion occurs when this liquid comes in contact with molten metal. The working temperature range of ISIS B of 50 to 200 °C results in other advantages as there are no corrosion problems and no risks of hydration.The fact that no explosion occurs when ISIS B contacts molten metal leads to a revolutionary solution for the metallurgical industry in terms of safety. Especially in critical areas - like tap-holes - new safety standards can be achieved.Together with the TÜV Austrian Holding AG a risk analysis was done for a water cooled tap-hole as well as for a tap-hole cooled with ionic liquids. It is shown that using the new technology the risk can be decreased dramatically and the importance of a best available technology is described."

Jan 1, 2014

By C. R. Ross

"The purpose of this paper is to review the activities of international organizations concerned with the problem of dust hazards in mines and to indicate the extent of Canadian participation in these activities. The work of the International Labour Office in sponsoring conferences and reports on the appraisal and control of dust hazards and in the development of standard radio-logical classifications is considered in some detail. Also discussed are the role of technical societies, such as the American Conference of Government Industrial Hygienists, in the development of proposed standards for dust exposure and the functions of international committees concerned with particular hazards, such as the U.I.C.C. (Inter-national Union Against Cancer) Committee on Asbestos and Cancer."

Jan 1, 1969

By W. R. Green, B. W. Barde

"Geological exploration involves the collection and analysis of a wide variety of information. A basic problem in interpretation is to determine the interrelationship s of the different data. A number of statistical methods can be applied to this problem, provided that subsets of data can be selected.We have recently developed a set of interactive computer programs which provide the cap ability to quickly examine a large set of data, and may be used by people with little previous computer experience. There are two main stages in using this system. First is selection of subsets of data , by applying various tests on the values of given items. This includes matching specific entries in descriptive fields, and minimum - maximum tests on numeric fields. The second stage is basic statistical analysis and data display , including histograms, 2-D scalier plots, probability (cumulative frequency) plots, and correlation matrices. All output can be viewed on a computer terminal, and important parameters changed to produce the most effective display for use in interpretation.This system has been applied to a number of different exploration problems. An example was the determination of the nature and extent of mineralization of a gold prospect in the Queen Charlotte Islands, from drill-hole data. With the aid of the computer programs , a mineralized zone was defined, and locations for further exploration identified."

Jan 1, 1984

By P. Archer

The Blondeau Formation has been examined in a stratigraphic drill section at Barlow Lake. The formation contains pyroclastic flows and volcanogenic sediments throughout, but epiclastic sedimentary rocks dominate the upper parts of the section. Five distinct types of pyroclas tic flows are known in the section, as well as minor mafic lava flows. Volcanogenic sediments are commonly intercalated with the true volcanic rocks. Sedimentary rocks include fine-grained intraclastic sandstones, heterolithic sandstones and green and black shales. Interpretation of the origin and relative disposition of the volcanic and sedimentary rocks favours a model of near-emergent vulcanism in an upward shoaling environment.

Jan 1, 1984

By M. S. Alam, Jae-Chun Lee, M. Tanaka, K. Koyama

Extensive research work is being carried out at AIST for developing energy saving green technology for base and precious metals recovery. In the present work, a new flowsheet is developed for copper recycling from waste electronic circuit board where copper was recovered by leaching followed by solution purification and direct electrowinning of Cu(I) from ammoniacal alkaline solution. In this new technology, power consumption in EW circuit was greatly reduced. This paper describes the overall process with an emphasis on different aspects of solution purification where impurities were selectively removed by cementation and solvent extraction techniques under nitrogen atmosphere.

Jan 1, 2004

By D. Richardson

Presentation Objectives ?Demonstrate the utility of 3D modelling for visualizing exploration data ?Demonstrate the target generation ability of 3D model query methods Exploration Criteria -Example Given the Geology of Sudbury What Are Our Exploration Criteria? (selected examples) ?Geometry ?Trends ?Lithology ?Proximity to Sulphides ?Length and Grade of Anomalous Mineralization ?Distance from Footwall In Addition ?Geophysical Criteria ?Economic Criteria ?Amount of Available Space ? Depth

May 1, 2006

"Air Products approached LAC Minerals in 1987 to initiate trials with pure oxygen in the leach circuit at several LAC facilities in Canada. This paper gives an overview of oxygen use and covers specific operating data from the Doyon and Terrains Aurifères mills near Val D'Or in northwestern Quebec. LAC also uses oxygen at the Macassa mill in Kirkland Lake, Ontario.In addition to the LAC facilities, oxygen is currently in use for test purposes at the Holt McDermott mine in Kirkland Lake, Ontario and the Camflo mine near Val D'Or.There are two requirements for oxygen in the cyanide leach mill. Firstly, oxygen is required in the familiar gold dissolution reaction as follows:(1) 4 AU (s) + 8 NaCN (aq) + 02 (aq)+ 2H 20(aq) - 4NaAu(CN) 2(aq)+ 4Na OH(aq)Of the reagents on the left side of the equation, the availability of gold is fixed by the ore in question. Obviously, water is available in excess, 1eaving cyanide and oxygen as the limiting constituents in the process. Most mills operate with an excess of cyanide, which is fairly closely monitored. Dissolved oxygen levels, however, are not normally watched very closely and find their own level based on the temperature, the availability of compressed air and the ability of the ore to consume oxygen.Typical D.O. levels are in the 3-8 ppm range, however levels less than 1 ppm are not uncommon for refractory ores.With pure oxygen, dissolved oxygen levels as high as 30 ppm can be achieved. (Figure #1). This greatly accelerates the kinetics of the leach reaction and may also shift the reaction further towards completion thus increasing gold dissolution slightly."

Jan 1, 1990

By G. Paquet, E. Godin

"Since the mid fifty's, worlwide pellet production capacity has constantly risen (Fig. 1, Ref. 1 l. There was however at that time no real incentive to decrease production costs but only to produce as many pellets as possible. State of things changed with the iron and steel market recession, starting in 1975, and is currently leading producers to improve pellet quality and to reduce fuel and power consumption.At the Port-Cartier pellet plant, the energy needed for the induration of pellets ranks first in overall operating costs. An important step was made when starting admixing coke breeze in 1980. Oil prices justified the use of coke breeze as a direct replacement in terms of dollar/ton, however, while gaining expertise in using solid fuel a significant decrease in energy consumption was observed (Fig. 2, Ref. 2).In 1985, the ""Centre de Recherches minérales"" was commissioned to undertake research work to investigate the effects of further increasing coke addition to the pellet mix. The positive results of that work led to a 1,5% coke addition plant trial during the fall of 1985. Both laboratory and industrial results are discussed in this paper."

Jan 1, 1986

By Arun .. J. Basu

The paper introduces Intelligent Air Management (IAM) as the core activity of M&I Group of Companies (M&I) for providing a total solution to any air management problems for mining and mineral processing operations implementing a comprehensive systems approach through a world-wide network of strategic alliance partners and in-house engineering team and manufacturing facilities in Mississauga, Ontario, Canada. Recommendations for energy-efficient ventilation in a vibration and noise free environment are made with the patented and innovative solutions supported by extensive computational fluid dynamics (CFD) studies. The solution scope extends from an intelligent and integrated exhaust silencer to a complete ventilation sys-tem solution including inlet and outlet control design and ducting for diffusers and silencers.

Apr 1, 2005

By Paul Staples, Fred Woodcock, Robert Grant, Mike Cooper

"Noranda's Brunswick Mining Division, near Bathurst, New Brunswick, processes 10,500 TPD of complex Cu-Pb-Zn bearing ore. Brunswick uses conventional rod and ball milling techniques to achieve a flotation feed size of 75% passing 400 mesh. Over a two year period, testwork was performed using a Marcy pilot plant ball mill to assess the impact of several key variables on secondary grinding efficiency. Four graded mill charges were used to compare balls and slugs at 25 and 29 mm sizes. Data was evaluated by determining grinding rates using a commercially available steady state simulator. Results were critical in Brunswick's efforts to achieve finer grinds while minimizing cost per tonne.IntroductionBackgroundThe Brunswick orebody is an extremely fined grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite.Size reduction at Brunswick is performed by three separate parallel lines consisting of rod mills, primary and secondary ball mill circuits, all in series. The line 3 grinding circuit is presented in Figure 1."

Jan 1, 1997

By James R. Lang

The Xietongmen deposit is located 350 km west of Lhasa, Tibet. It is a new, high-grade porphyry copper-gold discovery and the first deposit to be systematically explored by a western company in southern Tibet. In 2005, Continental Minerals Corporation drilled 21,332 m of core in 63 holes and demonstrated excellent lateral and vertical continuity of high-grade copper-gold mineralization over an area 750 m by up to 350 m in size which remains open in all lateral directions. Drill intersections repeatedly yield grades >1% Cu equivalent (based on gold and copper prices) and include 308.5 m at 0.87% Cu and 1.25 g/T Au (1.60 CuEQ%), and 315.6 metres at 0.61% Cu and 1.11 g/T Au (1.26 CuEQ%). Extensive drilling in 2006 will expand and delineate the deposit, and metallurgical, engineering, environmental and socio-economic evaluations will begin. Xietongmen is hosted by volcanic and intrusive rocks of the Gangdese belt, a magmatic arc active between 120 and 30 Ma along the southern margin of Eurasia. Pervasive alteration is dominated by a well-mineralized K-feldspar and biotite assemblage, and by a more peripheral sericitic assemblage also with strong chalcopyrite. Major vein stages include chalcopyrite-bearing quartz, biotite, magnetite and pyrite-pyrrhotite types.

May 1, 2006

By P. P. Sinha, D. N. Bhatia, B. R. Ghosh, R. K. Gupta

Medium carbon, low alloy, high-strength steels containing Ni, Cr, and Mo are used for the fabrication of various types of high-strength fasteners required for launch vehicle structures. Cold heading properties and response to hardening and tempering are the essential requirements of the material for fabrication and application, respectively. Combining these two requirements is essentially warranted in high-strength fastener-grade steels. Cold heading properties require ductility, which can be achieved through spheroidizing treatments. In the absence of a suitable spheroidizing cycle for medium carbon 3.8 Ni, 1.8 Cr, 0.3 Mo steel, experiments were carried out with a theoretical understanding of the alloy system. This paper presents the experiments and results obtained after a spheroidizing treatment, which was carried out to optimize the process. Hardness measurements were carried out and microstructural studies were conducted to assess the spheroidization process and to determine the optimal spheroidization parameters.

Jan 1, 2007

By A. Bamber

Canadian leadership in a global mining context will depend not only on entrepreneurship and best practice but also on technological innovation. This paper argues for more ambition and commitment to R&D for technological innovation in Canadian mining. It focuses on underground hardrock mining, where past R&D initiatives have simply not stood the test of time, and it is important to examine why. Concerns arise because industry’s commitment to R&D has not been sustained over time. Innovation through exploration, processing, and environmental technologies has been more significant. Meanwhile, R&D capacity and synergies in government institutions and universities have not been exploited. There is a need for more commitment, coordination, and collaboration by industry, governments, and universities. This paper examines some corporate models that have achieved sustainable innovation, along with some that have not. A strategy for innovation is discussed that relates to culture, commitment, coordination, and collaboration.

Jan 1, 2005

By Manqiu Xu, Peter Wells, Gord Bacon

"A methodology is proposed for milling flowsheet design using flotation rate, selectivity and residence time distribution data. The flotation rate data and the difference in flotation rates between the main minerals to be separated are determined from laboratory batch tests. The residence time distribution (RTD) data is calculated using the tanks-in-series model assuming each flotation cell is a perfect reactor. The rate, selectivity and RTD data can be used to calculate the optimum flotation cell number in a bank for rougher/scavenger in a commercial plant.This methodology is demonstrated in a case study of a nickel sulfide ore. It is shown that miniplant rougher/scavenger data can be closely predicted from a batch test using the proposed methodology.INTRODUCTIONIt has been the trend in the past several decades that large flotation cells are increasingly used. This is largely driven by the economics as ore grades are getting lower and the rate of ore processing must be increased in order to keep mining operations economically viable. The development and evaluation of 250 to 500 m3 WEMCO SmartCell and Outokumpu TankCell flotation machines are well in progress. There are many advantages in using large cells: fewer cells, less floor space, lower power cost (although this is now being questioned for fine particle flotation), simpler circuit, simpler control, and lower auxiliary equipment cost (Arbiter, 1999). As flotation cells are getting larger, the importance of cell hydrodynamics, namely, air/slurry dispersion, power intensity, froth transfer, residence time distribution (RTD) and short-circuiting are being fully recognized (Jonaitis, 1999; Weber, et al., 1999; Gomez and Finch, 2002). It is not the intention of this paper to discuss flotation cell scale-up. The intention is to answer what is the optimum number and size of cells in a flotation bank for a given throughput. Figure 1 illustrates this problem facing design engineers. The same mean residence time required for a given throughput can be achieved in a single large cell, or many smaller cells in a row. A few cells of large size may be more cost-effective but they may not be as effective as more cells of smaller size in achieving the optimum metallurgy."

Jan 1, 2005

By R. S. Fukuhara, M. J. Allan

"Highmont, a wholly owned subsidiary of Teck Corporation, operates a 25,000 ton/day mine and concentrator located in the Highland Valley of British Columbia. Construction of the plant commenced in the spring of 1979, and production from one grinding line began in late December 1980. The second grinding line began production in March 1980.The ore body consists of two main zones, the east and west pits, containing 134 million tons of ore, averaging 0.26% Cu and 0.27% Mo. Mineralization consists mainly of chalcopyrite (2/3), bornite (1/3), and molybdenite.The concentrator design incorporates an A-B-C grinding circuit (auto mill ball mill - crusher), followed by bulk flotation, copper-moly separation and leaching for moly concentrates. The two grinding and bulk flotation circuits are parallel and independent. Concentrate storage is provided between bulk flotation and copper¬moly separation and also ahead of molybdenite leaching. The plant design has been previously described in some detail. (""THE HIGHMONT CONCENTRATOR"" by C. V. Sibbald, CIMM Bulletin, March 1981).This paper will outline some of the problems associated with the construction, startup and early operation phases of the concentrator. The objective is to help others avoid some of the potential pitfalls by outlining those areas where problems occurred, or where things went well. Criticism of design or equipment is not intended."

Jan 1, 1982

By Gregory A. Johnson

Operations and Maintenance departments have long had an adversarial relationship. The widespread evolution and adoption of modern management techniques such as Reliability Centered Maintenance (RCM) and Lean Production however has driven interest in working co-operatively to optimize overall plant performance. Mining and minerals operations have long adopted RCM in maintenance, and are now adopting Lean throughout the organization. Modern management initiatives like these explicitly call for co-operation between the two disciplines of maintenance and production and many advances have been made in the realms of people and methodology. One area that has lagged behind in supporting these developments however is information systems. Enterprise Asset Management (EAM) systems in maintenance and newer Manufacturing Execution Systems (MES) in operations have not been truly integrated in the way needed. Complicated plants, different software architectures, continually changing conditions and many variables have lead to systems problems which have contributed to the maintenance/operations divide. Master data synchronization (the ?plant tree?) and integrated reporting of real-time data with transactional data are just two of the issues that are being solved by new approaches in information technology including web services and service orientated architectures. New technologies are coming on-stream to enable the final ?bridging of the gap?.

Feb 1, 2008