Search Documents

By R. Loj

Katowice Coal Holding (KHW) is one of the largest coal companies in Europe. The company owns five coal mines with a daily output of around 60 000 tons of coal. In the Katowice city area, very good quality steam coal is extracted. The depth of mining varies between 400 and 1100 m and some of the mines rank amongst those most afflicted by methane in the Upper Silesian Coal Basin, with the methane hazard having a significant impact on production and safety. ?Myslowice-Wesola? mine, being a part of the Katowice Coal Holding is characterized by high methane and rockburst hazards. The mine is equipped with a modern surface drainage pumping station. At the mentioned mine, longwall 514 was selected for analysis of its methane emission. The longwall was extracting the thick seam 501 (over 4 m), at a depth of over 900 m, which was subject to high stress and high gas concentration conditions. At a distance of about 50 m above, seam 501 is covered by thin seam 416. The strata between these two seams are sandstone and mudstone layers. In the floor of seam 501, with a thin shale interlayer, is located seam 510, which is the thickest (over 10m) and richest coal seam in the Upper Silesian Coal Basin. In longwall 514 and it?s vicinity, methane was the dominant risk. For this longwall three methods of classical gas drainage were carried out. At first, drainage was undertaken using long boreholes from a cross-cut at level 665 m, located far from the production panel. Later, it was performed using typical boreholes drilled from the ventilation gallery (tail gate road). Finally, it was undertaken using a degassing drift executed in the upper coal seam 416. All of these headings, ie. cross-cut level 665 m, the ventilation road and conveyor road in seam 501 and the degassing drift in seam 416, were equipped with media for drilling and proper drainage pipelines. Due to the high rockburst hazard and some problems with caving, several kinds of de-stressing and torpedo blasts were carried out in both coal seams and roof rocks. The subsequent analysis and experiments allowed the establishment of some general rules for carrying out degassing operations effectively. The effectiveness of a degassing drift was demonstrated. In some instances, the system allowed more than 70% of the total methane released to be captured and fed into pipelines. The aforementioned blasts had a marginal impact on methane emissions and the efficiency of degassing methods. Cyclic drilling and regular switching of boreholes in phase with the mining progress and working face advance were shown to be essential.

Aug 1, 2013

By S. Minamiguchi

Grain refinement is effective to enhance strength and ductility of metallic materials. However this advantage has not been utilized fully for magnesium alloys in industry because microstructure control through thermomechanical treatment is difficult owing to their poor deformability. The authors proposed a high-speed heavy-reduction rolling for production of Mg alloy sheets. It was found that the deformability is significantly improved at high speed and that the thickness can be reduced 60% by one-pass operation even at room temperature without fracture at the rolling speed higher than 1000 m/min. In this study, commercial AZ31B sheets were rolled at 2000 m/min between room temperature and 350°C, and quenched immediately after the rolling. The sheets rolled at 200°C show the finest recrystallized microstructure with the mean grain size of 2.2 Rm. They show outstanding mechanical properties with the tensile strength of 293 MPa, and the elongation of 25%. It is concluded that high-speed rolling is very advantageous for grain refinement and improvement in mechanical properties as well as deformability and productivity.

Jan 1, 2006

By Mike Smith, George Chung

"A 23 million dollar Flotation Plant has been commissioned at the Iron Ore Company of Canada in 1998. Nine OK-50 cells &re used to float silica in this 1,400 tomes per hour plant. The paper details project development, construction and operating results. This plant gives IOC the capability to produce not only high quality blast furnace pellets of varying silica, CaO and MgO levels, but also a high iron, DR grade pellet. The first activity was simply to sit down with the suppliers, Outokumpu, Wemco. GL&V and Svedala, to discuss applications and share experiences. We learnt what each supplier had to offer, what features would particularly suit this application, what options were offered, what were the materials of construction, how the equipment is maintained, which wear parts require replacement, etc., etc. We tried to learn as much about the equipment as the suppliers themselves knew. Then we tried to learn more: we contacted users and asked about any weak points, which options were worth incorporating and which items were not. We then discussed these points with the suppliers and established how potential problems might be overcome."

Jan 1, 1999

By Gustavo Angeloci

Artisanal mining is a rudimentary activity that today attracts over 30 million people in virtually all developing countries around the world. As the price of gold has steadily increased over the past decade, 15 million people have become involved in extracting this metal in 55 countries. Individuals have switched to mining from primary industrial sectors such as agriculture to increase their income. These workers generally have little capital, low education levels, and no previous experience in mining. Together with a lack of technical support from governments, these factors lead to disorganized and informal mining activities that generate environmental and social chaos. The absence of technical knowledge and capital has caused a proliferation of Gold Ore Processing Centres (GOPCs) around the world established by local entrepreneurs, who provide a way for miners to process their ores using amalgamation for a fee that is relatively low to non-existent. Gold recovery by the independent miners rarely exceeds 30 % and gold-rich tailings are left at GOPC facilities as a form of payment. GOPCs recover around 90 % of the remaining gold using cyanidation, flotation, and amalgamation, without any compensation paid to the miners. In processing these mercury (Hg)-contaminated tailings, Hg cyanide complexes are produced that are dumped into aquatic environments, leading to rapid bioaccumulation of Hg by fish. In the town of Portovelo, Ecuador, the establishment of partnerships between GOPC entrepreneurs and artisanal miners has proven to be successful in forming legal small-mining companies to create more equity and reduce pollution. About 108 GOPCs operate in Portovelo-Zaruma, with 40 % of these still working illegally without proper regulation and permitting. Over 20 % of these GOPCs continue to use grinding, concentrating and amalgamating of the gold, with 58 % performing cyanidation of tailings and/or gravity concentrates, and 15 % combining flotation with cyanidation. About 94 % of the GOPCs concentrate the ore prior to applying amalgamation, which significantly reduces Hg emissions to the environment. Incorporating flotation has given the operators increased skills in mineral recovery, with the side benefit of producing a copper concentrate as added value. Despite these innovations, mineral recovery is still inefficient, and waste management is a major challenge in creating true sustainability in this sector (technical efficiency together with social and environmental responsibilities). Further organization, training and capacity-building are needed. The principles of Lean Manufacturing Methods ("Just in Time" production and "Automation") are suggested as possible techniques to assist small GOPCs to become sustainable. In this concept, a larger mining company can become associated with artisanal miners in a partnership to provide training and investment for exploitation of small deposits that would be infeasible as a single large operation. As well, an International Training Centre for Artisanal Miners (ITCAM) is being established in Portovelo with collaboration of the Government of Ecuador to further enhance and upgrade mining activities in this region. ITCAM will provide artisanal miners with technical, business and environmental training to become responsible small-scale miners. In building this new capacity, ITCAM intends to create an atmosphere of trust to attract private and corporate investors to become partners with artisanal miners.

Aug 1, 2013

By P. W. A. Mayer

"As the push toward the northern regions of Canada steadily increases to exploit the rich mineral reserves, interest is steadily rising in respect to accessibility and climatic conditions and the problems posed thereby. In twelve years of operation, the Iron Ore Company of Canada, and associated companies, have found, through advanced technology, ingenuity and, most of all. need, some of the answers to the running of a profitable year-round open-pit mining operation."

Jan 1, 1966

By B. J. Morash

"The six mineable coal seams at Quintette Coal Limited (QCL) vary in thickness from 0.75 m to 9.5 m and include waste partings varying from 0.2 m to 4 m thick. They are highly faulted and folded in some areas and dip angles range from horizontal to 90 degrees. Due to this variation in thickness and orientation of the seams, several different mining methods are used to economically recover the coal. The key to QCL's success depends on the timely collection of detailed geology data and on mine planning which allows selection of the best method of mining to achieve maximum coal recovery with minimum dilution and cost. This paper will describe the various methods of mining employed and the criteria used to select them. IntroductionThe unique challenge in mining at Quintette Coal Limited (QCL) is to extract large quantities of coal and waste, from a complex orebody, with constricted areas for mining and waste disposal. This challenge dictates the mining of as many as four 10 m benches per year, through complicated coal structures, from three separate open pits with a total of 19coal seams. This total is made up of 5 seams at Mesa, 8 seams at Wolverine and 6 seams at Shikano (Fig. 1).Computer-aided mine planning and scheduling is carried out on a routine basis to ensure the prudent selection of methods of mining, to produce plans which ensure delivery of appropriately blended raw coals to the plant, and to coordinate disposal of large quantities of waste.Several methods of mining are applied simultaneously, and as a result coal and waste are released at different rates from twelve to fifteen mining faces. In order to ensure uninterrupted flow of material from excavators and to utilize the truck fleet effectively, a computerized dispatch system is employed.GeologyGenerally, geological conditions can be related to structural (faults and dip angle) and/or stratigraphic (coal seam and interseam waste thickness) sources"

Jan 1, 1988

By I. B. Lambert

The guide has been developed by officials from resources and environment agencies in the Australian Government and the South Australian and Northern Territory Governments. It elaborates on the Australian Government?s policy that new uranium mines are to be approved subject to world best practice environmental and safety standards. The guide outlines the best practice principles and approaches that apply generally to mining in Australia, before giving more detailed consideration to best practice environmental protection and regulation for ISR mining.

Aug 1, 2010

By Krishna Parameswaran

"This paper discusses energy use and conservation in the primary copper industry and illustrates eco-efficiency considerations, using select examples of practices at ASARCO LLC, an integrated primary copper producer and others in the industry that promote eco-efficiency. The World Council for Sustainable Business Development first publicized the concept of eco-efficiency at the Rio Earth Summit in 1992. Eco-efficiency is a management concept linking environmental and economic performance and is aimed at generating added value for a business through, among other things, increased resource and energy conservation and reduced environmental impacts throughout the life cycle of the product or service. This concept differs from sustainable development in that focus is only on economic and environmental factors and does not include social considerations. In the metal mining and processing context, this added value can be realized by implementing practices that promote conservation of water and mineral resources, conservation of energy, minimization of waste, reduced emissions and effluents and increased recycling. The examples from the primary copper industry used to illustrate eco-efficiency considerations include: water and energy conservation in mineral processing, adoption of flash and bath smelting processes, emission reduction and process improvement associated with fire-refining, implementation of green chemistry in electrorefining, promoting product stewardship initiatives and fostering renewable energy project on disturbed mined lands.INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting And Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co-products. Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills, two leach, solvent extraction-electrowinning (SX-EW) plants and a copper smelter in Arizona and a copper refinery in Texas."

Jan 1, 2017

By S. Sundararajan, Z. Lin

ABSTRACT Fierce market competition and demand have made it imperative for mining companies to achieve higher productivity and operational efficiency. The selection of the best mining method and equipment combinations will enable companies to meet production and efficiency targets. Continuous mining is increasingly preferred by companies for its high efficiency and low unit costs. We developed simulation models for two continuous mining systems: the continuous surface miner (CSM) system and the at-face slurrying (AFS) system. Considering two different case studies, the paper discusses application of developed models to determine the optimal number of trucks and equipment capacities for the two systems.

Jan 1, 2013

By Jamal Jafari, Abbas Sam

"The concentration of the fourth production line at Golgohar includes 66% iron with Blaine number of 500 cm2/g. For pelletizing process, the feed iron grade should be greater than 68% with minimum Blaine number of 1800 cm2/g. In this study, the low intensity magnetic Separators, particularly the feed particle size distribution of LIMS were considered. The feed particle size distribution of the separators was optimized to prepare an appropriate concentrate (as mill pelletizing feed). The samples were performed from the LIMS feed and after grinding, four d80 (64, 103, 132, and 15 3µm) were prepared. Then, laboratory magnetic separation experiments were conducted on these samples. The best results obtained using d80 of 132µm. In this particle fraction, the iron grade and Blaine number were 70.3% and 1571 cm2/g, respectively. Therefore, it seems necessary to include a grinding and classification systems before LIMS stage. According to the presence of a high amount of -132 µm particles in the initial feed, an inverse closed circuit was selected. The hydrocyclone was designed in three units as the classification system with 62 cm (diameter), 22 cm (overflow outlet) and 11 cm (apex diameter). By simulation of hydrocyclone with USIMPAC software, the size distribution of underflow was determined. Based on these results, a ball mill with dimensions of 6.7 m (length) and 5 m (diameter) was designed as grinding system.INTRODUCTIONGole-Gohar iron ore concentration plant No.4 (Polycom Plant) in Gole-Gohar Industrial and Mining Complex was installed to increase production capacity as well as treating the circulating load from AG and SAG mills of the main concentration plant of the complex. The load from the mine is crushed using jaw and cone crushers. The crushed ore is then combined with the circulated load and the combination is then grounded using HPGR and ball mills respectively.After comminution, there is a magnetic separation plant which includes a medium intensity magnetic separator (MIMS) followed by three low intensity magnetic separators (LIMS). Final concentrate dewatering is done using three belt filters. After the primary magnetic separation, the ore is upgraded to 62% Fe content and final concentrate which is the product of LIMS has 66% Fe content."

Jan 1, 2016

By R. Tipman, T. C. Burnett

"A general computer program has been written to calculate material balances using multiple regression techniques. The program can handle metal assays or size distribution data obtained in multiple surveys of the flotation circuit. The ""best fit"" weight split is calculated between the input and product streams by minimizing the sum of squares of the residual errors using all of the available data. The program includes an assay adjustment feature in which each assay is recalculated to fit the ""best fit"" mass balance. Thus assay or sampling errors can be easily identified. Also the assays can be statistically weighted so the most precise measurements are given the most influence on the material balance. The computer output reports the mass balance, the actual and corrected assays, the percent metal recoveries and the significance and confidence levels for the weight splits.The program enables a rapid and accurate evaluation of mass balances from large masses of data obtained in multiple surveys around a flotation circuit. The effects of changing process variables can be quickly evaluated with statistical confidence."

Jan 1, 1978

By Pamela Paradis-Sokoloski, Deni Thibodeau, J. Denis, Samantha J. Espley, P. O’Donnell

"During the previous decade, the role of spray-on liners within the mining industry was limited to providing a corrosion resistant coating to screen and bolts; however, increasingly, liners are being used as ground support products. Expanding use and testing of liners have demonstrated their ground support function, yet the definitive support mechanism is still under debate. The most promising theory is the retain/hold/reinforcement concept (Kaiser et al.,1992). This conceptual theory has been the basis for the recent underground trials at INCO where, specifically, shotcrete and MIROC Mineguard were tested in two trials to further define limitations and applications of each liner.In a cursory overview, shotcrete is becoming accepted as a support product, while Mineguard is only slowly gaining acceptance.This discrepancy is the result of the corresponding life-spans within the industry, whereby shotcrete has had wide-spread use for decades, yet Mineguard has only recently been introduced. Currently at INCO, shotcrete is primarily used: to provide support in poor ground conditions, to add stability when developing through backfill, and to provide damage control in seismically active mines. It is also used to protect production headings and secondary-blasting chambers from fly-rock damage during blasting. Despite an obvious support function of the liner, shotcrete has always been used in addition to bolts and screen. Comparatively, Mineguard is still in the testing stage, where the greatest potential is increased productivity for applications in multi-tasking development headings. In this scenario, Mineguard provides instant support to replace screen, and bolts temporarily. When the heading has advanced, the drill and support crews work in tandem, drilling off the next round and installing bolts for long-term radial support, respectively. Other potential applications of Mineguard are within production headings to replace screen in the back, and screen and bolts in walls. The potential for both liners to replace conventional support is clearly war-ranted, such that defining the support role was the primary goal of the two underground trials."

Jan 1, 1996

By John Rowson, Caitlin Brown, Kebbi Hughes, Joseph Esslifie-Dughan

The McClean Lake mill in northern Saskatchewan, Canada, is operated by Orano Canada Inc. and has been in production for the last 20 years. The tailings preparation process at the mill has been designed with decommissioning in mind, to produce tailings that are geochemically stable over the long-term within the site’s tailings management facility. Twenty years of study have contributed to a detailed understanding of geochemical and geotechnical properties of the McClean Lake tailings. Validation of the tailings properties has occurred through in-situ sampling campaigns conducted initially every year, and later every five years. Each sampling campaign has applied the same rigorous sampling procedure to provide data with useful correlations year over year. Each campaign result compares elements such as the inherent variability of the tailings, consolidation of the tailings and variations in the tailings placement methods. We will discuss lessons learned from seven sampling campaigns over 20 years and present data to show the reliable tracking of geochemical evolution of the in-situ tailings over time; providing opportunities for continuous improvements.

Jan 1, 2020

By R. D. Hossack

"The selection of a site for plant facilities is a function of several factors and has as its objective the maximization of profits, given fixed markets and sources of raw material locations. In practice there are several sites, any one of which or a combination of two or more would be suitable to meet the basic requirements of source of supply of raw material and labour and still fulfill market demands. The model used to select the optimum profit combination utilizes both computer programs and traditional financial analysis techniques. Of the three computer programs used in the mode), one is a linear program and another is a transportation simulator. Basic cost and price data are required. In examining costs, three levels are used: (a) distribution costs of raw material to the plant and finished goods to the market; (b) direct production costs at the plant, such as labour and locally supplied material; and (c) capital and overhead costs at the plant, such as construction costs, taxes, insurance, and federal and provincial cost allowances. The direct costs generally depend on the scale of operations, so that a large plant in one location may have a lower unit cost than two smaller plants. This, of course, must be balanced against distribution costs. In examining profit, it is necessary to think in terms of the price and volume of sales at each of the market locations. Given basic data and relationships, the model can be used to optimally locate production facilities or, alter-natively, optimally structure a transportation network given existing locations of plants and markets. It is dynamic to the extent that it can react to changes in volume, price and cost to optimally locate an additional plant, the expansion of existing plants, the shutting down or cutting back of plants, or the restructuring of distribution networks."

Jan 1, 1970

By E. J. Wasp, T. L. Thompson, T. C. Aude

The paper will deal with some of the more important technical aspects of slurry pipelines as they apply to the mineral field. In addition, the use of these technical concepts in arriving at realistic economic figures will be discussed.

Jan 1, 1970

By S. Ross, M. Mayhew

"Kirkland Lake Gold introduced battery equipped vehicles (BEVs) at the Macassa Mine in 2011. The fleet of underground BEV haulage trucks and loaders has grown over the years to over 30 units, the world’s largest, currently handling approximately 80% of the daily production tonnage. The inflow and outflow of air occur through a limited number of relatively small openings, which limits the air volume delivered to the underground workings. In addition to improving air quality, the reduced heat load generated by the BEV (when compared to diesel equipment) had a significant positive impact in the workplace. The use of BEV for material handling has enabled increases in production that would not have been possible using diesel equipment.INTRODUCTIONMacassa mine was developed as a track-drift access mine, with the most recent shaft (#3) sunk in 1986. A new mining complex, the South Mine Complex (SMC) was discovered below the 5025 foot elevation south of traditional mining areas, and the majority of mining now occurs in the SMC. The discovery of that zone has led to an internal ramp which is used to access the SMC and haul ore to #3 shaft.The amount of airflow that can be moved through the mine is limited by the existing infrastructure to surface. This amount was recently increased to near its practical maximum from 118 CMS (250 kCFM) to 151 CMS (320 kCFM).Both diesel and electric equipment are used at Macassa. Tethered Load-Haul-Dump Machines (LHDs) have been replaced with Battery Electric LHDs, due to their increased mobility and depth of the mine. Battery trucks continue to replace locomotives to transport both ore and waste to the shaft, as mining has transitioned from tracked levels to trackless level and haulage has transitioned from horizontal levels to an inclined ramp.EQUIPMENT FLEET AT MACASSAMost of the primary material movers utilized at Macassa Mine are battery operated. As the mine goes deeper the battery technology will continue to be critical to the success of the operations. With over 300,000 hours of proven operation success, the battery technology and equipment will continue to be a major part of Macassa’s future."

Jan 1, 2019

TABAKOTO / SEGALA ? Annual gold production approximately 100,000 oz ? Debt free ? Unhedged ? Combined surface reserves 949,000 oz ? Combined 9 year life Tabakoto open pit reserve 568,000 oz (3.4m tonnes @ 5.26 g/t Au) Segala open pit reserve 381,000 oz (3.98m tonnes @ 2.98 g/t Au)

May 1, 2006

By J. A. Haskin

The Engineering Department at Flin Flon has the following responsibilities: 1. Underground Surveying. 2. Open-Pit Surveying and Supervision of Blasting. 3. Mine Geology and Examination of Prospects. 4. Design of Plant Additions and Improvements. 5. Miscellaneous Field W ork, Reports, etc. The entire surface plant, as well as the underground workings, are located by co-ordinates based on a triangulation system covering an area approximately one mile long by one-half mile wide. The origin of this system and one end of the base-line is the southwest corner of Township 67, Range 29, west of the Principal Meridian. The bearing of the base-line was determined from the township boundary, which runs true north, so that all other bearings are almost astronomical. This is a great convenience when our surveys must be tied to mineral claims, rights-of-way, and land subdivisions. As the base-line extends across Flin Flon lake, its measurement across smooth ice was simple and accurate. The length, slightly over 1,600 feet, has been adjusted for the temperature and tension of the standard tapes used and checked sufficiently to ensure a maximum error of 1 : 15,000. Each angle was repeated ten times, but as no special refinements were used, errors of as much as four or five seconds are possible. The elevation of the origin of the triangulation system was approximately 1,050 feet above sea level. The use of this true elevation in our surveys would have resulted in negative elevations underground as soon as the mine reached a depth greater than 1,050 feet. To avoid this complication we therefore added 4,000 feet to this elevation. The collar of the Main shaft, for example, which is actually 1,072 feet above sea level, appears in our records as at elevation 5,072. Underground surveying, which follows standard practice, is done by two mine surveyors who share three helpers. The meridian is taken underground from two wires hung in either of the two vertical shafts.

Jan 1, 1935

By Paulo F. T. Sachs

ERP systems have been widely implemented nowadays in several industries. However, ERP was originally designed to fit former MRP and MRP II users, and most of the ERP research has been focused on discrete manufacturing . On the other hand, process industries ? and mining in particular ? present many peculiar characteristics, which are difficult to comply with ERP systems standard functionalities. Again, very limited research has been developed covering enterprise management systems in mining. The objective of this paper is to identify, through an explanatory study that includes a case study methodology, how ERP systems manage the functional areas of the mining industry, and how they fit into the mineral value chain IT requirements. A secondary objective is to identify the gaps between ERP?s functional capabilities and the mining industry business requirements, and to point out the perceived benefits they generate to the companies.

May 1, 2004

By L. W. Hamel

"Two 35 foot diameter enviro clear thickeners were tested in series as CCD units from June until October, 1978. Up to shutdown in July, we ran with automatic bed level control via the level probes and underflow pinch valves. Despite extensive efforts, we were unable to eliminate the surges created between the units by the opening and closing of the pinch valves. Early in July, the best rake speed and gap setting were determined. After shutdown, the enviro clears were run by manually controlling the pinch valves. These efforts were successful.A few mechanical problems were encountered while operating the thickeners. New units should incorporate more support for the drive coupling and a rubber feed seal. A few modifications of the instrumentation control scheme will be required before the units can be fully automated. A less sophisticated automatic flocculant addition system will accomplish the desired results. Control of the underflow withdrawal via the pinch valve should be investigated further. Our best results were obtained by keeping the feed volume to the No. 1 enviro clear constant. Surges were controlled by opening or closing both underflow valves proportionately.Capacity of the enviro clears is dependent of many variables. The ore treated during the test program was much finer than that reported on in R & D Project Report 76-02. Conditions were never steady enough to determine best flocculant dosage or addition point(s). The lowest soluble losses were obtained at very high wash rates. The underflow densities drop but the soluble losses also drop. Regression equations were developed in order to assess the effect of the various parameters. Within the range studied, these equations will predict the performance of enviro clear thickeners as CCD units on Elliot Lake ores. Our results show that the enviro clear thickeners are a viable alternative to the conventional CCD thickener."

Jan 1, 1979