Search Documents

By M. Potesser

Higher prices for natural gas or oil have motivated the copper industry to reexamine the modes of oxygen and oxy-fuel burner usage at operating plants. With rising energy costs and the growing importance of environmental protection, burner usage and burner operations have become the focus of several investigations and optimization efforts. One possible approach to lower energy usage is through combustion using tonnage oxygen. When such oxygen is used, the flame temperature increases and operational efficiency is improved. As well, with the correct technology, due to the presence of lower levels of harmful substances such as NOx in the off gas, there is improved environmental performance. As regards copper production, furnaces are employed for both concentrate smelting or for melting and casting operations. The use of tonnage oxygen in concentrate burners for smelting provides for a higher thermal efficiency. For furnaces employed for melting, air-operated burners may in fact have an initial advantage because a long radiant flame is typically generated, thus providing for a higher degree of heat transmission. This paper describes the new experimental burner chamber of Messer Austria GmbH which provides for testing of the combustion of natural gas with oxygen or oxygen-enriched air and the use of special water cooling ducts that simulates a metal charge during melting, The operational effectiveness of the burner is determined from temperature and off-gas analysis data. The paper also discusses future trends in burner technologies including a new patented burner. Cu2007 - Volume III (Book 2) The Carlos Diaz Symposium ou Pyrometallurgy Edited by A.E.M. Warner, C.J. Newman, A. Vahed, D.B. George, P.J. Mackey, A. Warczok Toronto, Canada,

Jan 1, 2007

By R. F. Hochstein, A. J. Neale, B. C. Flintoff

"Process control technology holds very significant potential benefits for many mineral and coal processing plants. The impact can be expected in terms of performance improvements (e.g. increased throughput, better quality control, higher availability), through reduced operating costs (e.g. lower reagent consumptions, manpower reductions) and in the form of intangibles (e.g. reduced vulnerability to manpower turnover, increased productivity in the user group). However, the installation of a process control system will represent considerable capital expenditure and will generate an operating cost. No management team would approve the funding for such a project without some reasonable measure(s) of the profitability of a proposed system. This paper describes a methodology for addressing the justification problem. Of particular interest is the approach to quantifying performance improvements, frequently found to be the predominant benefit of process control.INTROPUCTIONProcess control has become widely recognized as an essential component of any processing operation. It has direct impact on productivity, process efficiency and product marketability. The reported pay backs associated with successful installations underscore this observation. As a consequence, many operators who have little in the way of process automation are looking to initiate control projects, while those who currently enjoy some level of automation are looking to upgrade existing control systems (= process + instrumentation + hardware + software + operators + support). While the emphasis here would appear to be on retrofit process control projects, new plants, or those currently in the design stage, will usually find themselves in one of these categories shortly after startup 1."

Jan 1, 1990

By E. Onal, C. Craddock, A. Chapman, M. R. Endsley

ABSTRACT Mining equipment operators must interpret and respond to complex information delivered by technology-centric rather than user-centric systems. The ability to achieve high situation awareness (SA) in the face of this data overload is a key challenge to effective decision-making and information exploitation. Incidents attributed to human error that compromise safety and result in loss of revenue, or even life, are often the result of system designs that overload human cognitive capabilities. This paper defines SA as it relates to the operation of mining equipment and describes the design and preliminary evaluation of a new electric shovel operator user interfa

Jan 1, 2013

By Lloyd W. Trevoy

Titanium and zirconium heavy minerals occur in the tailings streams from processing plants which use the hot-water extraction process for recovery of bitumen from tar sand. In a research program conducted by Syncrude Canada Limited, the crude tailings stream was upgraded to produce quality zircon and titanium mineral products. To process the tailings through conventional upgrading equipment, bitumen residues must first be removed from the mineral grains. Then, by gravity separation, fines and coarse sand grains were removed and a 71% heavy minerals concentrate was prepared which was further separated by high-tension equipment into zircon and titanium minerals concentrates. The zircon concentrate was upgraded by gravity, magnetic and high-tension cleaning to produce a high-quality 98% zircon product. The titanium minerals concentrate was separated into rutile, leucoxene and ilmenite fractions. Heavy minerals distribution in tar sand drilling core samples has been evaluated for various locations on Syncrude Lease 17, and expected annual production levels of heavy minerals have been estimated. A preliminary evaluation has been made of the potential for zircon, leucoxene and rutile production and for further upgrading of ilmenite and leucoxene to synthetic rutile for titanium dioxide pigment production.

Jan 1, 1978

By K. Adham, C. Lee

Over the last forty years, a number of specific fluidized bed applications in nickel extraction have been developed for commercial use. Five important processes have gained particular acceptance, namely, sulphide ore roasting, nickel sulphide (matte) roasting, nickel oxide reduction, laterite ore pre-reduction, and nickel chloride pyrohydrolysis. These applications involve different feed materials and process conditions, however, all benefit from fast reaction kinetics and high heat and mass transfer rates in the fluidized bed reactors. They have been studied, tested, and implemented by various nickel producers, who have published their results in many papers and patents. This paper examines the design issues surrounding the application of fluidized bed technology to the above nickel processes. Based on the available data in the open literature, computerized process modelling is used to provide generic flowsheets that illustrate the key features of each process.

Jan 1, 2004

By Jaeheon Lee

"Biooxidation of gold ores or concentrates could be a very attractive alternative to pressure oxidation (POX) or roasting to liberate the gold grains from various sulfides. Crushed heap bioleaching was successful in US and many operations using tank bioleaching of gold concentrate are currently running around the world. Many parameters need to be considered during the project of sulfidic refractory gold ore process. Capital and operation costs are among the most important ones. Run-of-mine heap biooxidation could be very inexpensive and the smaller the crush size (particle size), the more expensive the capital and operating costs for biooxidation application are expected. The capital cost of biooxidation could be a fraction of the cost for building POX plant or roaster and the operating cost could be 1/3 of POX or roasting depending on the method utilized. A new biooxidation process, Sand Farming, is introduced as an alternative to POX and tank biooxidation process. A relatively coarser particle size (P80 = 650 µm) of the process benefits the low cost of grinding against the conventional grinding size (P80 = 75 µm) for other options. The cost of Sand Farming is less than 40% of that of pressure oxidation with comparable gold recovery from the downstream process. This paper will review the laboratory scale testwork for various biooxidation process of sulfidic refractory gold ores and concentrates and provide the economic evaluation showing the biooxidation could be the most economic method without much sacrificing the overall gold recovery. INTRODUCTIONThe decreased availability and lower grade of raw materials has motivated industries to consider recovering values utilizing low cost process options. The process may treat high grade concentrates or submill grade ores that cannot be processed economically by conventional milling-flotation or leaching. Sulfidic refractory gold ores/concentrates have been economically processed by roasting, pressure oxidation, and biooxidation in stirred tank reactor. The process selection is based on a series of studies including multi-year long ore characterization and metallurgical investigations."

Jan 1, 2016

By A. J. Goodman

Introduction The position of Turner Valley in the foothills of Alberta, some thirty-five miles southwest of Calgary, is too well known to need further description. This attempt to interpret in detail the nature of the structure, and its relationship to neighbouring structures, together with general observations on the foothills belt, is based on work carried out in the office of the Supervisory Mining Engineer, at Calgary. The object in view was the correlation of the mass of evidence which had accumulated from the detailed examination of drill cuttings, and to discover, if possible, its structural significance. Unfortunately it is not possible to publish most of this detail owing to its confidential nature, and in consequence the reader is asked to accept certain statements, which under other circumstances would not be made without supporting evidence. The main argument for the general structural interpretation rests on evidence which has already been made public, and it is possible to proceed to logical conclusions on the main points. The evolution of ideas concerning the structure of Turner Valley is somewhat difficult to follow, as, compared with all that has been said on the subject, there is not a great deal on record.

Jan 1, 1930

By Alim Ullah

Danieli entered into the Direct Reduction (DR) field in order to offer its clients complete turnkey facilities for steelmaking?from processing of raw materials through finished products. The Danarex® Process produces a passivated product, called the Supermetallic (SPM), without hot-briquetting. One of the main features of the Danarex® Process is its ability to produce approximately 50% of the Direct Reduced Iron (DRI) through reduction gas generated in a reformer and another 50% through recycling preheated furnace exit gas. Some other distinguishing features are: separation of carburising and cooling zones and the use of double bustle for better distribution of gas inside the shaft furnace. A pilot plant was set up at Hazen Research, Inc., Golden, CO in order to show that the integrated process works as expected and to obtain process data. The SPM obtained was of a very high quality, evidenced by metallization levels of 92% to 98%. The carbon content could be controlled between 1.5% to 4.0% by varying the operating conditions and approximately 75% of this carbon was present as Fe3C. The product was tested for inertness by Chilworth Technology, England, using UN standard tests and was found to be safe for outdoor storage and transportation.

May 1, 2003

"9.1. IntroductionThe application of the electron microprobe for in-situ analysis of platinum-group minerals (PGM), first reported by Borovskii et at. (1959) and Genkin (1959), has resulted in a large and growing number of analyses of unidentified PGM. Figure 9.1 charts the increase in the number of reported unnamed PGM from 3 in 1959 to a total of 140 by 1979. All these minerals, with the exception of UN1968-5 and UN1976-1, were analyzed with the electron microprobe.There has been no recognised or consistent manner for reporting these unidentified PGM. The term ""unnamed"" has been used for PGM that are considered to be new species without a name as well as for PGM which have not been exhaustively compared to named and unnamed PGM in order to determine whether they are unique. Many of the so-called unnamed PGM are only unnamed because of poor microprobe analyses or because larger than usual elemental substitutions (e.g. Bi for As) made it difficult to calculate the true stoichiometry. Some of these unnamed minerals have been unnecessarily reported with non-stoichiometric formulae, as discussed by Cabri (1980). Better analytical data should reduce the number of such proposals.Another unfortunate practice, possibly used to by-pass the scrutiny of the Commission for New Minerals and Mineral Names, I.M.A., is to report a ""new"" mineral by referring to it by a name made up of its constituent elements. This has been deplored on a number of occasions (cf. discussion in Fleischer et at., 1976, p. 179), but some journals continue to publish such material. The Commission on New Minerals and Mineral Names has not recognised such ""names"" and these PGM are therefore included in this chapter with other unnamed minerals.A further example of inconsistency in reporting unnamed minerals is the report of a specific ideal stoichiometry with no further details (not even an analysis!); sometimes with a note that this will be reported in greater detail in due course. I have also been guilty of similar optimistic statements and, unfortunately, it is not always possible to follow through. Some authors give data on unnamed minerals in such a discrete manner that their reports are sometimes missed in literature searches."

Jan 1, 1979

By Christoph Broeckmann, Andrew Gardula

"The adoption of high-pressure grinding throughout the cement industry has yielded enormous savings in energy and wear material costs. There are also a number of installations, which are applied in iron ore and kimberlite processing operations. High pressure grinding offers the same potential for energy and media savings, as well as opportunities for improved, downstream metallurgical performance, in hard rock mineral processing. This paper focuses on developments in machine design and wear surface engineering for high-pressure grinding of the hard rock ores in the mineral processing industry.INTRODUCTIONIn the early eighties 3.4 % of the world electric energy was consumed for crushing and grinding operations of minerals and 0.6 % in the ore dressing industry. During that time using a laboratory press Prof. Schönert found that interparticle comminution at high pressure requires remarkably less energy as conventional grinding technologies. In grinding of cement clinker he expected energy savings between 33 and 50 % compared to ball mills [1]. Piston presses are limited in throughput. Thus, the principle of interparticle comminution was adapted by the use of high pressure grinding rolls (HPGR) to a continuous plant process. Figure 1 shows the main components of a roller press: The roller nip of width s is formed between the floating roller (1) and the fixed roller (2). The diameter of the rolls will be denoted with D, the width with B. The total press force F can be adjusted using a hydraulic system with two or four pistons (3). In order to compare machines with different roll geometries the specific pressing force p is introduced:"

Jan 1, 2005

By Robert H. Clark

Introduction During the last twenty years, science and industry have been strenuously endeavouring to discover new sources and new kinds of liquid fuels and to work out suitable chemical methods for their production. One of the new possibilities for the production of liquid fuel on a large scale is law-temperature carbonization of various grades of coal. The use of alcohol as motor spirit, in spite of its relatively low calorific value, is being widely investigated. Its production by fermentation of sugars, its recovery from the sulphite liquors of the paper industry, its production directly from wood and also from calcium carbide, have all been considered. At present the most promising line of investigation would appear to be the further development of those technical processes which yield liquid fuels from coal; since science has shown the possibility of preparing all kinds of liquid fuels and even the complete conversion of coal into oils. The present paper will consider briefly: 1. The production of primary tar by low temperature carbonization of coal. 2. The hydrogenation of coal. 3. The synthetic processes of Dr. Franz Fischer.

Jan 1, 1928

By A. Philipp, A. S. Middleton, G. A. Harron, A. B. Durham

"Basal till sampling techniques were used to search for gold mineralization in the Timmins, Ontario area. During 1978 and 1979, approximately 90 overburden sampling drill holes were completed in Murphy and Hoyle Townships to test specific geophysically defined target areas. A conventional tricone dual tube drill system, and a unique retractable tricone/rock coring system were used to various advantages.First pass till sampling at 800 to 1200 ft intervals perpendicular to ice transport direction yielded anomalous gold values in till and carbonatized quartz pyrite-rich bedrock chips, and lateritic soil. Subsequent induced polarization-resistivity surveys defined the areal extent of a pyritic carbonate alteration zone. A second pass till sampling/limited rock coring program evaluated the gold mineralization potential of the alteration zone. Diamond drilling has substantiated the till and bedrock gold anomalies. Further evaluation of this mineralization is currently in progress. IntroductionThis paper describes an integrated geochemical/geophysical gold mineralization discovery case history in Hoyle Township. This discovery is on a property jointly owned (I983) by Canamax Resources Inc. and Du Pont of Canada Exploration Limited. Exploration of the property began in 1978 by Rosario Resources Canada Ltd. and in 1979 a joint venture agreement was signed with Du Pont of Canada Exploration Limited. Rosario Resources Canada Ltd. was taken over by Amax Minerals Exploration in 1981, which became Canamax Resources Inc. in 1982.The work described in this paper deals with a gold mineralization discovery located three-quarters of a mile northwest of the gold deposit currently being readied for underground exploration and development. Further drilling is required to investigate the economic potential of the gold mineralization herein described."

Jan 1, 1987

By B. Krysa, J. Qiu

The zinc pressure leach plant at HBM&S's operations is now in its fifteenth year of operation. Current pressure leach operation is steady at a concentrate processing rate of around 26.5 tonnes per hour. A new cellhouse with a design capacity of 124,000 tonnes per annum and the capability of expansion of up to 154,000 tonnes per annum was commissioned in July 2001. The potential to expand the capacity of the pressure leach circuit and associated processes, as well as the purification circuit and casting plant, to meet the maximum capacity of the cellhouse has been investigated. This paper reviews current operation of the zinc plant, as well as the possibility of a capacity increase without major process modifications or major capital expenditures.

Jan 1, 2008

By J. D. Campbell

"Coal is one of Alberta's major fuel resources, but its distribution, especially in the flat plains region, has been somewhat obscured by surficial deposits. After a period of neglect, easily strippable plains coal is presently approaching a position of dominance in electrical power production, a position it is likely to retain for a number of decades in the face of strong competition from hydro and nuclear power. Accordingly, the Research Council of Alberta has undertaken an inventory survey of the province's supplies of this resource.In the southern part of the province and in the north-central forest-fringe area, some strippable coal is found in the Belly River Formation and its equivalents, but major strippable coal reserves in large areas of central Alberta occur within the Edmonton Formation. The survey is planned on a reconnaissance scale, drilling test holes at 2-mile intervals in selected large areas. It appears to show that, in well-settled regions, large reserves of strippable coal are only to be expected where they have long been known; major presently unknown bodies of coal must be sought in unsettled regions or at depths too great for strip mining. However, such bodies might still be economically competitive with hydro and nuclear power in the production of electric power for some time to come."

Jan 1, 1967

By Mohamad Kharseh

There is general acceptance that climate change, which is the most important challenge facing humanity, is anthropogenic and attributed to fossil fuel consumption. Therefore, improving the performance of our existing energy systems and deploy more renewable energy resources is an urgent issue to be addressed. Geothermal refers to existing of heat energy in deep rock and sedimentary basins. This energy can be used to drive a power turbine to generate electricity. Traditionally, geothermal has been exploited in places with the plentiful hot water at relatively shallow depth. In the light of fact that ground temperature increases with the depth everywhere on the Earth, engineered geothermal systems (EGS) can be installed in any place to exploit the geothermal in generating energy. Unfortunately, the high exploration and drilling costs of boreholes is the main barrier to commerciality of EGS worldwide. In addition, there are technical problems associated with drilling big depth. In oil producing countries such problems can be addressed by utilizing whether active or abandoned oil or gas wells and, consequently, EGS can produce power at profit. The current study presents an analysis of a binary geothermal power generation system for commercial electricity generation in Qatar. For this purpose, two binary cycles are assumed the main difference between them is that the first one is air cooled while the other will be water cooled. The performance of the two cycles and the possibility of improvement has been shown. Economic analysis the power plant shows that the levelized costs of electricity is 3.6US¢/kWh and the pay-back time is less than 8 years.

Aug 1, 2013

By Sengpasith Houngaloune

Arsenic, which is a toxic and carcinogenic element, causes serious environmental problems throughout the world. It is also known as a major contaminant in the non-ferrous mining and extractive metallurgical industries, thus its disposal is one of the most important environmental issues for the mining and metallurgical industries. In order to ensure a safe disposal environment for the final wastes, stabilization of arsenic has been studied extensively with various approaches. Solidification/stabilization (S/S) represents one of the most effective methods to reduce the availability of arsenic in soil and waste by transforming toxic or potentially hazardous phases into less hazardous ones. Cement based S/S processes could reduce the solubility of arsenic in solid waste, using inorganic binders such as cement, lime, and pozzolanic materials. A new tailings management technique, called cemented paste backfill (CPB), has become widely employed for improving mining techniques and for tailing storage purpose and this technique could also enhance arsenic stabilization, by fixing the contaminants in the binder matrix. Disposal of arsenic in the form of scorodite (FeAsO4?2H2O) has been widely accepted as currently the most suitable method for stabilization and the safest known storage material. The Bio-scorodite process has been reported to be more economic and environmentally friendly method than the chemical crystallization processes. Retention of arsenic by schwertmannite (Fe8O8(OH)6SO4), a metastable ferric oxyhydroxy sulfate mineral, has gained more attention in the recent years. Schwertmannite has a large specific surface area and high capacity to adsorb arsenic in solution. Several researchers have reported that the transformation of schwertmannite to goethite could be retarded by the presence of adsorbed arsenic; therefore schwertmannite might be viable alternative for long-term storage of arsenic. In this paper, various approaches used in arsenic stabilization are reviewed with emphasis on the development in the recent years.

Aug 1, 2013

By A. Piche, J. Nantel

"This paper describes the recent developments in Canada toward the establishment of a Canadian Centre for Mining Automation and Robotics, at McGill University and École Polytechnique in Montreal. The role of the Mining Association of Canada (MA C) and of the National Advisory Committee on Mining Automation will also be reviewed. IntroductionIn order to remain competitive, the mining industry must increase its productivity and reduce its costs. In the last two decades, this objective has been achieved through mechanization. From now on, any further improvement in productivity will be gained through increasingly more automated mining equipment.Recent international developments following the Versailles Economic Summit in June 1982, having given rise in Canada, to a renewed interest in applications of robotics and automation to mining.The mineral industry in Canada is at a crossroads. Competition in emerging from everywhere: lower grade ore bodies, increasing distances between viable mines and markets, third world massive production of certain commodities, substitution of "" space age"" materials (ceramics, plastics, composites, etc.) for metals.On the positive side, it is generally believed that present mineral commodities, i.e. base metal, gold, iron, industrial mineral s, etc ., will continue to be in high demand for centuries to come despite substitution. New applications for conventional metals will be found and the enhancement of certain properties of these conventional metals mean continued demand. For some mineral commodities, there will never exist an y substitute."

Jan 1, 1988

By J. Suarez Condezo, E. Herrera Alarcon

The Ilo Smelter Modernization Project will require treating the slag from the Peirce Smith converters in Slag Cleaning Furnaces using pig iron technology. Currently the slags from the converters show variable magnetite contents. The copper contained in this slag is recovered in Reverberatory Furnaces, where the smelting rate was improved due to the high silica content of the converter slag. Preliminary industrial tests where developed to clean the slag from converters using pig iron. The results showed that the magnetite content has a significant influence in this process. This work describes the actions that are being implemented in the converter operation to control the magnetite content in the slag in order to maintain the high copper recovery of the smelter when the new facilities are commissioned. This task will demand a strong control of both the slag chemistry and converter practices in order to get the copper recovery considered as the design criteria (~97.4%).

Jan 1, 2007

By P. C. Benedict, J. A. Titcomb

"The following description of the geology of the Northern Empire mine is recorded by the senior author, but is based on the observations and complementary mapping of both authors.The Northern Empire mine is a mile east of Beardmore, and 100 miles northeast of Port Arthur, Thunder Bay district, Ontario.Production started in March, 1934, and terminated in September, 1941. The total number of tons milled was 425,866, from which 153,103 oz. gold was recovered. The lowest level from which ore was mined was the 1,900- foot, but considerable drifting was performed on the 2,075-foot and 800 feet on the 2,415-foot, the deepest level,The vein strikes about N.72°E. and has an average dip of80°S. In stoped sections the quartz averaged about 2 feet wide. On the 1,725-foot level it was drifted on continuously for more than 7,000 feet. In the mine as a whole, practically no commercial ore was found beyond points 1,400 feet west and 1,800 feet east of the shaft. Conspicuous wall-rock alteration extended throughout this section, but not much beyond these limits. There was some splitting of the vein and widening of the alteration halo on the lower levels. The average general colour of the quartz changes with depth .The vein is in 'Keewatin' lava flows, to which it is almost conformable. It lies only a short distance south from the 'Timiskaming-Keewatin' contact ( Fig. 2). This contact is marked by a black graphitic fault. So far as is known the fault is parallel, or nearly parallel, with the flows in strike, but dips at 72°S., which is 5° flatter than the average dip of the overturned flows. A post-vein, almost flat sheet of diabase about 550 feet thick cuts outthe vein from about the 650- to the 1,200-foot level ( Figs . 1 and 3). If it was intruded along a fault, the fault had only minor displacement. A strong alteration halo extends to 200 feet above and below the diabase. The vein was conspicuous but in large part it was below ore grade for 100 feet or more above and below the diabase.-"

Jan 1, 1954

By BARRY BANNATYNE

Gypsum in Manitoba is quarried from the Jurassic Amaranth Formation a1 Gypsumville and Harcus; it has been mined near Amaranth and Silver Plains. At Gypsumville, gypsum is carbonate- free but has thin clay laminae between gypsum layers; the rock is folded in places, and some anhydrite is present. At Harcus, gypsum contains scattered dolomite, both as patches in a penemosaic pattern and as thin layers; small chalcedonic concretions also can be found. The quarry at Harcus was opened late in 1978 and currently produces about 100,000 tonnes annually. The two inactive mines near Amaranth operated from 1932 lo 1963 and from 1967 to 1970, and contain a central anhydrite layer. The mine near Silver Plains was flooded from an underlying artesian aquifer in 1975 and has not been reopened. Manitoba gypsum is used in cemem plants in Mani1oba and Saskatchewan and in wallboard plants in the three Prairie Provinces.

Jan 1, 1984