Search Documents

By D. R. Murray

"A promising long-term solution to uranium tailings reclamation has been the establishment of vegetation directly on the waste material. The soil profiles of areas vegetated for 0, 3, 8 and 10years are characterized as to the extent of soil development . The characteristics are compared with the visually interpreted soil profile. Organic matter content is presently the best analytical judge of soil development. Vegetation procedures have produced a build-up of organic matter in the top 10cm of tailings where natural microbial populations flourish. The CN ratio is high and the profile depth shallow, suggesting the need for additional fertilizer applications.IntroductionThe reduction of surface erosion and improved aesthetics of uranium tailings has been accomplished by the establishment of a vegetative cover. In 1971 research concentrated on developing methods of plant establishment at minimal cost and soil amendments on uranium tailings in Elliot Lake , Ontario. One process of stabilization used on a large scale was direct seeding of grasses and legumes into the tailings which had received only limestone and fertilizer treatments. Fertilizer additions were made for varying lengths of time in subsequent years to maintain the established cover.Maintenance-free vegetation would be possible once a soil profile developed with sufficient nutrient recycle and plant regeneration capabilities(1). Tailings vegetated in 1971, 1973 and 1978 that had received either 3 or 5 years of maintenance fertilizers were examined for soil development profiles. The extent of soil development and the relative effect of time and fertilizer would provide direction on reaching the goal of a self-sustaining cover.This paper is an abridgment of Division Report MRP /MRL 81-126 of the same title(2)."

Jan 1, 1984

By Bert S. Hall

"IntroductionThe purpose o f this paper is to review the evidence at hand concerning the earliest centuries of cast iron in Europe, from roughly 1400 A.D. until the second half of the sixteenth century. For the most part it is concerned with the relationship between two technologies which emerged first in China and then later appear in Western lands, gunpowder weapons and iron founding. We should not assume, as I hope to show later in this discussion, that weapons constituted the only product for which the iron founder had any market, but it is clearly true that attempts to produce weapons constituted the most severe technical challenge for the early founder. Firearms appear for the first time in Europe in the 1320s and develop into significant weapons on the field of battle by the end of the century. Theirs is a complex history, subject neither to easy summary treatment nor to simplified models of development. I hope to be able, through the analysis of the evidence concerning cast iron, to show that one important strand in the fabric of gunpowder's history concerns the materials from which cannon could be made. This question is subject to a number of shades of meaning, because ""cannon"" can be made for many purposes under a profusion of different names, and under sharply varying conditions of use. As a result, the question of materials is frequently really a question of competing materials, and involves a complex set of factors, of which production costs and the ultimate safety of the user seem the most important. Judged in this manner cast iron was an important but unsatisfactory metal for weapons purposes until 1543, at which time English founders learned to make iron muzzle-loading cannon which could rival bronze ordinance in most important performance criteria, but which cost much less to produce. With that event, the history of cast iron and the history of weapons entered into the close relationship that persisted until the advent of rifled artillery made of steel in the middle of the nineteenth century."

Jan 1, 1983

By Robert B. Parsons

"It is quite likely that more than a handful of junior exploration companies will receive some startling news from their accountants this spring when 1989s tax returns are being prepared. These companies could find that, for the first time ever, they will have to write a cheque to the federal government on account of a new federal capital tax which became effective July I, 1989IntroductionMany mining companies which have never had to pay a federal income tax are finding that they indeed have a tax liability for 1989. Non-producing companies, such as junior exploration companies, almost automatically assume that they don't have to pay any income tax. But, a new tax imposed under the Income Tax Act catches especially the company that has no income.Effective July 1, 1989, a federal capital tax (some call it a corporation minimum tax) is payable by any corporate carrying on business in Canada where the corporation has ""taxable capital"" exceeding $10 million. As a result of the popular use of flow-through shares in recent years, many junior exploration companies are finding that their balance sheets show capital stock over $10 million, and that they are consequently caught by the new tax. Further, some of these companies are finding, to their chagrin, that the tax for 1989 was due on February 28, 1990, and that non-deductible interest is ticking away on unpaid taxes."

Jan 1, 1990

By E. S. Moore

DEEP oxidation and-secondary enrichment of ore deposits, although so important in many parts of the world, are comparatively rare in the Canadian shield. Intensive glaciation during the Pleistocene epoch accounts for their rarity. Glaciation has cost Canada much in the destruction of not only enriched ore deposits, but placers that must have been developed near our numerous gold deposits during the long period of weathering that pre-ceded the Pleistocene. There seems to be a very common misconception regarding the average depth of rock that has been removed from the shield by glaciers. These bodies of ice are usually given credit for the removal of the greater portion of the thousands of feet of rock that we know has been eroded from this large area since Precambrian time. As a matter of fact, the average thickness of solid rock removed can be measured in tens rather than even hundreds of feet, although very deep erosion has resulted in some sections where the glacial ice has been constricted in depressions, such as deep valleys and lake basins. On the other hand, there are few areas within the shield where the glaciers have not disturbed practically all of the mantle rock and some feet of the underlying bed-rock. The chances of finding deeply oxidized cappings and enriched ore deposits are therefore comparatively few and these have been found chiefly where favourable structural and topographic conditions for their formation and preservation have existed. Faulting has been responsible for several of these deposits, and easily decomposed rocks, such as. sulphides and carbonates, have been very important factors. Topographic features, such as high and resistant hills, favourably situated with respect to the ore deposits have, in a few cases, played a part in providing protection from glacial erosion and in furnishing head for the descent of surface waters. At least four cases of oxidation to depths quite abnormal in the Canadian shield have so far been found in Ontario. These are the Helen and Josephine iron mines in the Michipicoten district, the Keeley silver mine in South Lor-rain, and the Ross gold mine in Hislop township, Cochrane district. A deeply oxidized zinc deposit of unusual interest occurs in the Precambrian rocks in New York State, not far from the Canadian border, and there arc the well-known iron deposits in the Lake Superior region of the United States.

Jan 1, 1938

By R. C. Wallace

It was to be expected that the convening of the first Empire Mining Congress in June, 1924 in the city of London would turn men's thoughts very definitely to the question of exploring the mineral resources within the British Empire, the examining of her strength and her weakness in mineral material, and the consideration of steps that might advisedly be taken to strengthen her trade in minerals. That expectation was in part realized, though in the British way of presenting the case, and permitting the inferences to be drawn by implication. The opening address by the President of the Congress, to whom the Empire meant so much, gave a résumé of the contributions to the mining industry which were being made by the constituent parts of the Empire. The papers from the Institutes in Australasia, South Africa and Canada provided the details of resources and practice: while the individual contributions to the proceedings dealt with those phases of the mineral industry which are fundamental to the economic strength of British people, or to the health and well-being of the workers. While the subject matter thus presented was British mineral resources, and while the first consideration was the co-ordination and co-operation of British enterprise throughout the world, there emerged very clearly the wider viewpoint that the discussions had to do with a world industry, and with the contributions that that industry was making, and could further make, to the advancement of civilization irrespective of national boundaries, the world over. The invitations to representatives of the mining industry from the United States to participate in the Congress, and the warmth of approval which that participation evoked, were indications that such a congress cannot to-day be merely national in scope, and that trade in minerals, as in other natural resources, cannot be confined within national boundaries, but will seek its channels, unless artificial obstructions are too great, where the natural channels already exist.

Jan 1, 1925

By T. T. Wang, T. H. Huang, Y. C. Chiu

Quantitatively analyzing deformation of a tunnel with lining anomalies for structural safety evaluation is essential for sustainable tunnel engineering. However, a complete theory and associated methodology accounted for displacement of a built tunnel is absent. This manuscript introduces a novel characteristic matrix method proposed by the authors which is an integrated procedure that analyzes displacement of rock tunnels in operation. First, establish a numerical model expressing a specific state of the tunnel in interest. Derive the characteristic displacement modes by a unit disturbances and check their independency. Once the characteristic displacement modes are proved to be orthogonal (independent), they are ready for use. Given a tunnel displacement, modal decomposition returns the magnitude of each characteristic displacement modes that together consist the given displacement. By realizing the definite value of horizontal and vertical translation, rotation, uniform compression/expansion, elliptic deformation, triangular deformation…etc. for a tunnel displacement, one can distinguish tunnel displacement and deformation types from their modal composition. A circular tunnel with elastic structure and surrounded by elastic rock mass is chosen to demonstrate the outcome of characteristic modes and how they work. The influences of tunnel shape, elastic modulus ratio between rock mass and tunnel structure, and numbers of monitoring points on a tunnel profile were also discussed. Identifying possible tunnel deformation causes is attainable if further connections between mode combination and force increments were built.

Jan 1, 2015

By Wei Yingchun

Based on the deep burial depth of coal deposits in Huainan-Huaibei coalfields, Anhui Province, China, this paper puts forward the concept of partitioning of coal deposits according to occurrence conditions. This process is controlled by tectonic forces. The classification scheme of coal deposits exploration types is presented according to occurrence and mining conditions of coal deposits as viewed from the perspective of deep coal exploration properties. The principles underlying geological exploration services for the resources development are incorporated. There are six exploration types of coal deposits in the Huainan and Huaibei coalfields. Exploration models tailored to different types of exploration have been established and exploration strategies corresponding to different exploration models have been proposed. Steady-state temperature must be measured for the deep heat-harm type of coal deposit. The sealing coring of mine gas samples should be performed for the high mine gas type of coal deposit. For coal deposits with complex structures, such as those located beneath nappes, coal-controlling structural styles must be performed. Existing data on shallow districts are very important to the research of folds and fault-block types of coal deposits beneath and peripheral to old and existing coal mine areas. For the types of fault-block coal deposits hidden by thick Cenozoic cover, particular attention must be paid to comprehensive use of research on regional coal occurrence law and geophysical methods. The present work promotes the exploration level of coal deposits in Huainan-Huaibei coalfields to best meet the need for sustainable development of the coal industry.

Aug 1, 2013

By John Kazakoff, Andrew Mortimore

"Production at the remote Kumtor Gold Mine in Kyrgyzstan commenced on schedule in December 1996.The ore mined during the first few months of 1997 from the upper benches of the pit did not produce the results predicted by the feasibility study. Low metallurgical recoveries experienced at the time were cause for great concern.It soon became clear the recovery difficulties centred around the preg robbing nature of the ore.Procedures were developed to selectively stockpile highly carbonaceous low recovery ore types. Testing methods were developed in the mill to quante the preg robbing activity of the ore. Preg robbing masking agents were added to the process to reduce the preg robbing activity of the ore.The importance of coconut carbon activity relative to the preg robbing activity of the ore was realized. Every aspect of the performance of coconut carbon in circuit was evaluated and optimized to improve carbon activity.Mineralogical analyses were completed defining the deportment of gold in ore and process tailingsBy year end the recovery difficulties had been overcome and plant design production had been achieved. Process improvements continue through 1998."

Jan 1, 1999

By Eurípides do Amaral Vargas Jr., J. A. de Mello Franco

"It is frequently necessary to excavate a tunnel for Civil Engineering purposes, or wells for petroleum exploitation, in laminated rock mass like schists or phyllites or in highly foliated gneisses. The determination of the pre-existing in situ stresses is essential, in order to assure the stability of these excavations. In most cases, the pre-existing triaxial stress field is arbitrary in relation to the tunnel or well axis. For these rock masses the concept of Generalised Plane Strain can be correctly utilized.There are closed form solutions for the calculation of stresses in anisotropic rock masses under Generalised Plane Strain conditions (Lehknitskii, 1981 and Hong , 1994). Based on these analytical solutions, established for the cases of Generalised Plane Strain, a synthetic problem will be formulated: the theoretical in situ stress tensor acting on this rock mass will be determined, with the aid of Bayesian Inverse Problem Techniques, as developed by de Mello Franco (2009). Additionally, the reliability of results obtained will be evaluated, in accordance with the research performed by this author. INTRODUCTIONThe Inverse Problem Technique, as developed in the paper, is based on the definitions and concepts obtained from the current literature and used for the solution of Inverse Problems, but the innovation to be presented is the utilisation of Bayesian Techniques and the determination of the reliability of the results obtained. This will be shown in a synthetic example where the determination of the in situ stress tensor, from strain measurements in a drill hole is supposedly performed. It is assumed that this drill has its axis arbitrarily placed in relation to the rock mass. Generalised Plane Strain conditions will hold for use with problem. The equations of Beltrami – Mitchel, in agreement to Lekhnitskii (1981) and Ong (1994), will be used in this synthetic case, for calculating strains, hypothetically measured in the hole before the final excavations. Finally a synthetic example for the determination of the in situ stress in a fully anisotropic rock mass, based on Bayesian Techniques and its reliability, developed in de Mello Franco (2009) is presented."

Jan 1, 2015

By James F. Archibald

Research has been conducted for the Workplace Safety and Insurance Board of Ontario (WSIB) to characterize thin, spray-on lining materials (TSLs), as well as combinations of TSLs and conventional spray supports, and to assess their capacity for inhibiting damage created by mining-induced rockbursts. This study has been performed to assess the capabilities of such support systems for preventing rock and support material damage that often results due to rockbursting. A variety of TSLs and other spray support media were subjected to the effects of simulated rockbursting, through use of explosive detonation trials, to evaluate their damage mitigation capacity. Results have validated that TSLs and variant layer combinations may be as effective as or better than conventional support materials for mitigating rockburst or like damage in highly stressed mine environments. In civil engineering construction, and typically in underground tunneling operations where concrete linings are applied, liner deterioration is a continuing and pervasive problem that often requires expensive and time-consuming rehabilitation effort. The ability of TSLs to provide effective concrete structural reinforcement while providing sustainable resistance against underground or restricted environmental hazards, as with fires or dynamic failure events, may permit wider use of TSLs than is currently foreseen by the mining industry. Significant benefits for use of TSL materials in concrete liner rehabilitation and for concrete material protection have been assessed.

May 1, 2006

By R. L. Bruening, N. E. Izatt, S. R. Izatt

The need for selective metal separations has increased as the mining industry encounters more complex ore bodies and demand for higher performance end products expands. The Molecular Recognition Technology (MRT) process uses highly selective SuperLig® resins to remove desired metals from a variety of solutions in the mining and metals processing and recovery industries. MRT separation processes efficiently produce high purity metal products. In this paper, applications of MRT to metal recovery at mg/L to multiple g/L concentration levels are presented and discussed. Specific examples in the precious metal, nickel, cobalt, zinc, copper, and rare earth industries are given.

Jan 1, 2014

By T. Kagawa

Ever-increasing demands for non-ferrous metals owing to population growth and improvements in the standard of living in the world, under the constraint of limited availability of natural resources, would easily make us imagine that more efficient and sustainable developments in mining and smelting activities are required in the near future with due consideration for environmental concerns. In order to realize the efficient and sustainable development of mining and smelting activities and operations, the following issues are indispensable: (1) to investigate the up-to-date pollution control technologies of mine and smelter, (2) to promote those technologies, (3) to develop technologies which are environmentally friendly. This paper discusses the recent technologies for environmental conservation/prevention and their diffusion in the world, and also the key technologies required for the most desirable sustainable development.

Jan 1, 2007

By François Baillargeon

Two types of ore deposit provide the bulk of the world nickel production. They are the hypogene magmatic massive sulfide deposits and the supergene lateritic deposits. Platinum group elements (PGE) are also extracted from magmatic sulfide deposits. Recent sky-rocketing price of palladium has prompted the mineral industry to seek alternative resources. In such a manner has emerged the Lac-des-Iles type of target, a very low sulfide-bearing bulk tonnage type of deposit. Furthermore, unconventional (e.g. non-magmatic) types of deposit are now sought more intensively (Wilde et al., 2003). Considering both this trend of the PGE Industry, and that only a few magmatic deposits account significantly for the world nickel production, someone may wonder if a diversification of the hypogene nickel resources base would not be needed in the near future. Laterites are residual deposits developed on ultramafic rock under wet tropical climate. Are all ultramafic protoliths equal to generate high-grade lateritic deposit? Are some preweathering processes important to generate favourable ultramafic protoliths? The mineralogical heterogeneity of some ?dry? lateritic nickel deposits renders their ore beneficiation difficult. Is the type of nickel-bearing mineral found in the protolith a significant factor influencing the laterite heterogeneity? To contribute to answer all these questions, we have undertaken a research project on the nickel occurrences of the southern Quebec serpentinite belts. Why choosing this specific region for such a project? First because, due to continuous mining of asbestos ore since 1870, the serpentinite belts of this region are among the best exposed and studied in the world. Secondly, this region host a complete spectrum of nickel deposits that have been described before in the scientific literature. Furthermore, this region is slightly to moderately metamorphosed which make it perfectly suited to study the departure from magmatic nickeliferous paragenesis through various metamorphic conditions. As a matter of fact two orogenic events affected this region, the Taconian, in Ordovician time, and the Acadian during the Devonian. The magnitude and the timing of these dynamo-metamorphic events vary considerably through the region (Gauthier et al., 1994). These variations are now well constrained due to precise age dating.

May 1, 2003

By B. J. Keating

"AT PRESENT, it is not certain that any of the sulphide de in the Province of Nova Scotia attain the lower grade limit of 60 per cent sulphides over the minimum area of 1,000 square feet suggested as cut-off specifications for inclusion in this Symposium. However, several of them do include massive sections of substantial size and others represent concentrations of sulphide material that are well above average. It is felt, therefore, that a tentative classification of the deposits and presentation of their geological settings are justified and may help round out the genetic aspects of this study. Accordingly, data considered to be the most pertinent are assembled here in the event that some may fit into larger-scale patterns of mineralization that may take shape as a result of this investigation.The three principal massive sulphide deposits in Nova Scotia are the Stirling, the Smithfield, and the Walton. The locations of these are shown on the accompanying key-map (Figure 1).Three other deposits, the locations of which are also indicated on the map, are the Meat Cove, Rocky Brook, and Gays River de¬posits. Although these fall far short of the minimum dimensions and grade specifications referred to above they are singled out because they have received more than passing attention and are illustrative of the mineralization types to which they belong."

Jan 1, 1960

By P. H. Riordon

ONE OF the major sources of the world's supply of asbestos lies in a belt of ultrabasic rocks stretching through the Eastern Townships of Quebec where chrysotile asbestos has been mined continuously since 1878. The productive portion of the belt extends from the town of Asbestos in Shipton town-ship northeastward some 60 miles to the eastern edge of Broughton town-ship. (See map). Twelve mines, currently treating an aggregate of over 60,000 tons of rock daily, produce more than one million tons of asbestos :annually. An equal number of mines are now dormant, having for the most part exhausted their reserves. It is evident from the past and present activity, in this belt that it can look forward to at least half a century or more of large scale production. The host rock to the asbestos de-posits is essentially a peridotite which originally contained I 0 to 15 per •cent pyroxene. The peridotite, associated with dunite, pyroxenite

Jan 1, 1962

By J. Ander

About fifteen years age some mines in western Canada commenced using Diesel engines, partly for development work but also for operations on quite a large scale. In the Eastern mining field, the Diesel engine made its appearance some eight years ago and has since, at quite a number of mining plants, proved to be a reliable and economical prime mover. As a result, it is today used more extensively than could have been foreseen only a few years ago, and it is reasonably safe to predict that the next few years will see the Diesel engine utilized to a still greater extent in the Canadian mining industry. It is not much more than thirty years since the first Diesel engine was put in operation. During the early years of this century, the Diesel engine took, so to say, its first faltering steps in public service. Since then it has reached a high state of perfection, and its importance has grown in a most remarkable way, until today it is used in practically every field where power is required. It is slowly but surely superceding steam for a great many purposes, as, for instance, for ship propulsion. While in 1921 only about 8 per cent of all tonnage launched was motor-driven, the proportion had grown to 38 per cent in 1927, and for 1929 it was slightly over 45 per cent. Some of the finest passenger liners afloat are Diesel-driven. In the early days, Diesel engines were built only in comparatively small units. Today engines with a capacity per unit of up to 10,000 horsepower, or even more, are being built for marine and stationary purposes.

Jan 1, 1930

By Lynn I. Kelley

Potash is the primary industrial mineral produced in Saskatchewan, followed, in terms of gross value, by aggregate, sodium sulphate, salt, potassium sulphate, peat, clays, silica sand, calcium chloride brine and "clinker." Potentially economic deposits of kaolin, diamond and building stone are under evaluation.

Jan 1, 2001

By K. Ihara, R. Akiyoshi, Y. Takaki, S. Kang, H. Shishido

"Tensile tests and scanning electron microscopy-electron backscattered diffraction (SEM-EBSD) analysis were performed in an Al-Mg-Si alloy to clarify the effect of annealing and cold-rolling reduction on the texture formation. The hot-rolled specimens were cold-rolled with the reduction of 58-75%(CR1), followed by annealing at 773 K for 5 min(IA). The secondary cold-rolling(CR2)for the IA specimens with the reduction of 33–66%, followed by the solution heat treatment(ST), were performed. Focusing on the CR1 and CR2 specimens, the average r-values increased with higher primary and lower secondary cold-rolling reduction, respectively. This was considered to be due to the increase of r-values measured in the direction of 45 degree with respect to rolling direction, caused by the formation of the ß-fiber components (Brass {011}<211>, Copper {112}<111> and S {123}<634>) with high density. Based on the texture analysis of annealed specimens it was suggested that the high density of the ß-fiber components after IA and the small amount of stored strain energy of CR2 introduced by the lower cold-rolling reduction remained the ?-fiber components even after solution treatment.INTRODUCTION Al-Mg-Si alloys have been applied to automobile body applications, due to their excellent paint-bake hardening (age-hardening) and corrosion resistance compared to other aluminum alloy. On the other hand, the mechanical properties and deep drawability of Al-Mg-Si alloys are inferior to those of steels. Thus, it is important to improve the mechanical properties and deep drawability in order to expand the application components. One of the best methods to improve the deep drawability is to increase the Lankford coefficient (r-value). Previous studies reported that the increase of the average r-value ( ) improves the deep drawability. The relationship between the r-value and texture of the alloy is also well known. Inoue et al. reported that the ß-fiber components, such as Brass ({011}<211>), Copper ({112}<111>) and S ({123}<634>), increase the r-value measured in the direction of 45o with respect to the rolling direction. r"

Jan 1, 2018

By David Whittle

When does a project with questionable viability, warrant further investment? There are cases in which projects, which evaluate to a negative mean probable value, are worth investing in. There are also cases in which projects that evaluate to a positive mean probable value, should not be invested in. The author will present a model for ?project-control?which includes an adaptation of a well know grade-control concept. Comments on Resources and Reserves ?Resource and Reserve estimates are based on positive information (43-101). ?Reserve and Resource confidence qualitatively assessed. ?U.S. Geological Survey (USGS) recognizes Undiscovered Resources (U.S. Geological Survey 2003).

May 1, 2006

By R. Patrick

As a unique South African organisation, CSIR: Division of Mining Technology (Miningtek) strives to support the mining industry by improving health, safety and productivity through developing, adapting and transferring technology. Considerable effort is currently directed towards the development of potential non-explosive mining methods with the potential to allow continuous mining in narrow reef conditions. Besides improving productivity, continuous mining results in concentrated mining which has a significant impact on reducing infrastructural costs. Impact Ripping and Water Pulse Rock Breaking have been tried on gold mines, whereas Activation, Mini-Disc? cutting and the Plasma Holemaker are currently being tested on platinum mines. The organisation?s many years of experience in novel rockbreaking, together with its world-wide collaborator network, has placed it in a unique position to assist the mining industry and manufacturers in developing and/or adapting existing technologies for application underground. Currently a range of technologies are being investigated, which have reached different stages of maturity. The main technologies under investigation are; - Impact ripper system - Water pulse rock breaking - Activated undercutting rollers - Mini disc cutters - Electric rock breaking

Oct 1, 2001