Search Documents

By P. Lausch, Z. X. He, J. F. Archibald

"Documented underground fill failures have resulted because of the lack of adequate knowledge concerning fill strength and other physical parameters, as well as to a lack of consistent quality of fill materials being used by operators. On the basis of literature review and correspondence with backfill operators at 18 mines throughout the province of Ontario, non-systematic quality control procedures have been shown to exist, both within different levels of single operations and between separate mining operations, which act to provide inferior engineered fill materials and erratic application response in situ.Assessment of existing procedures set by mine operators for determining backfill physical parameters, and recommendation of optimum fill material testing and manufacturing guidelines are presented in this paper.A series of standard fill characterization test procedures are recommended to provide substantial, though not comprehensive, fill behaviour review. The purpose of these recommendations is to propose industry standards for backfill quality review. Data acquired could be utilized for fill design functions and as a means of comparing fill quality parameters between sites in a regular and more systematic fashion than is presently done."

Jan 1, 1993

By Gurupraveen Ramanathan

Shallow-dipping orebodies (45°–60° dip) present significant challenges for underground longhole stoping, particularly due to limited gravity flow, drill misalignment near the footwall, increased potential for dilution from hanging wall overbreak, and deviation from drill string sagging at shallow angles. These geometrical and operational constraints often lead to unblasted ore wedges and excessive overbreak when standard practices are applied. This study develops a structured, data-driven framework to optimize longhole stoping in such conditions by integrating five key focus areas: (1) mining method selection, (2) stope and drift design, (3) drill and blast optimization, (4) equipment selection, and (5) performance evaluation. The suitability of longitudinal longhole stoping was validated for narrow vein geometries using orebody analytics and prior case studies. Geometric modeling was employed to determine optimal stope height (15–20 m) and stope width (1.5–2.5 m), with drift widths adjusted based on orebody dip to maintain drill access and minimize unbroken ore. Drill and blast design emphasized sequential blasting over multi-ring methods to improve void control, reduce wall damage, and enhance fragmentation. Specific burden and spacing guidelines (e.g., 1.8–2.3 m burden; 2.5–3.0 m spacing) were applied based on stope width and dip angle, and patterns were selected based on geometry—dice-5 for narrow stopes, and 3-hole rows for wider stopes. Drill rigs—including top hammer and ITH models from Sandvik, Epiroc, Boart Longyear and CMAC-Thyssen—were evaluated for compatibility with drift dimensions and alignment accuracy. Equipment was matched based on dip, drift width, and the ability to access the footwall at shallow angles. Sensitivity analysis quantified how changes in geometry, drilling accuracy, and blast design affect ore recovery, dilution, and operating cash flow. Results show that tailored drift and stope geometries, combined with proper blasting and rig selection, can boost ore recovery to over 95% and reduce dilution to below 5% in optimal conditions. This methodology offers a practical and economically optimized solution for shallow-dip mining scenarios.

May 4, 2025

By J. Shahabpour

"Many porphyry copper deposits of the Kerman copper province in central Iran are associated with a consistent structurally con-trolled main drainage pattern, which is shown in this paper to be a useful regional prospecting tool in the search for new deposits. The main drainage trends also generally allow the distiction of high-grade (>0.2% Cu) from low-grade (<0.2% Cu) deposits. Topographic maps1:50 000 or geologic maps 1:100 000 have been found suitable for identification of promising drainages.IntroductionTrends of the main drainage systems transecting the high-grade porphyry copper deposits of the Kerman Region in Iran coincide with Quaternary age regional faults and fractures. Observation of such drainage trends can expedite regional evaluation prior to field examination. Thirty deposits located in the Kerman Region (Fig. 1) have been studied to identify common features that can be used for exploration purposes, especially for the first stage of regional exploration. A variety of field criteria are available for subsequent rapid field checking prior to trenching and more costly methods such as drilling, etc.Characteristic geomorphic features have been considered as aids in mineral exploration by many authors (e.g., Faniran, 1971; Piotrovski and Lubkashov, 1976; Verstappen, 1983). Clark et al. (1967) indicated the relationship between geomorphology and the supergene enrichment of copper in Atacama Desert, Chile, and correlated three periods of supergene enrichment with three periods of pediment disection. Seeland (1978) used fluvial drainage patterns for uranium and hydrocarbon exploration in the Wind River basin, Wyoming. Postolenko and Konopleva (1973) used the reconstruction of ancient valley systems for exploration of gold placers"

Jan 1, 1996

By Frederick Biery

Outline ? Project Challenges ? Results from 100 recent projects ? What factors are driving the best and worst projects ? A look at recent mining projects ? Conclusions

May 1, 2009

By H. J. Rowley

THERE are many varieties of limestone, but for the general purposes of the pulp and paper industry, two classifications are sufficient: (1) High-calcium stone, which should be quite free from impurities and contain not less then 90 per cent calcium carbonate. (2) High-magnesium stone, containing not less than 25 per cent of magnesium carbonate. Before proceeding with detail on the use of limestone and lime in the industry, a few words regarding the pulp products made in Canada are desirable. By far the largest tonnage is made by grinding spruce and balsam logs on rotating sandstones or on artificial abrasive stones of the Norton or Carborundum types. This mechanical or groundwood pulp finds its largest use in the production of newsprint paper, of which it comprises about 80 per cent of the total fibrous substance employed-the remaining 20 per cent being unbleached sulphite pulp. No limestone or lime is directly employed in making groundwood pulp, as contrasted with the chemically prepared pulps, all of which require one or the other form of the base for their processing. Sulphite pulps comprise the next largest tonnage group. They are produced by boiling, under pressure and at elevated temperatures, spruce and balsam wood in chip form in solutions of bisulphites and sulphurous acid. The usual bisulphites employed are those of calcium and magnesium. Sodium, potassium, and ammonium bisulphites give progressively better pulps, but to date, in the absence of efficient recovery methods, cost has precluded their use.

Jan 1, 1939

By Desmond M. Levins

"Australia has almost twenty per cent of the Western World&apos;s low-cost uranium reserves, located mostly in the Alligator Rivers region of the Northern Territory. At present, only one uranium mill is operating in Australia, but a number of new mills are planned for the early 1980s.Details are given of Australian uranium mining and milling proposals and the measures taken to minimize their environmental impact. Major factors affecting environmental impact are discussed, including treatment of liquid wastes, water management, control of radon and other airborne releases, and disposal of tailings. IntroductionAustralia is entering a new phase in uranium mining and milling activity . In the first phase of operations, between 1954 and 1971, about 10,000 tonnes of yellowcake was produced at five locations. Most of the production came from the mines at Rum Jungle in the Northern Territory and Mary Kathleen in Queensland. In the 1960s, the demand for uranium slumped, and much of the yellowcake produced at Rum Jungle was stockpiled by the Australian Atomic Energy Commission. The early uranium processing operations in Australia were typical of overseas practice at that time. Environmental problems were generally given low priority and pollution control measures were unacceptable by today&apos;s standards. There was little or no recycling of process water, acid waste streams were not neutralized and tailings dams were poorly designed. At Rum Jungle, oxidation of sulphides in waste heaps, tailings dumps and ore stockpiles subsequently led to destruction of vegetation and heavy metal pollution in a nearby river.In the early 1970s, major uranium deposits were discovered in the Alligator Rivers region of the Northern Territory. Significant orebodies were also located in the Great Artesian Basin in South Australia, in calcrete formations in Western Australia and at several locations in Northern Queensland. According to latest available estimates. Australia has about 160/0 of the Western World&apos;s uranium recoverable below $US 80 per kg U. Mining these orebodies will require pollution control measures more stringent than practised previously in Australia."

Jan 1, 1980

By M. J. H. Ruscoe

"The circulation wear rates of pure nickel, cupronickel and nickel-plated-steel coins were measured and found to be in the ratio 1:3:1 . The relative wear rates of nickel and cupronickel coins were similar to those reported in earlier studies, and the circulation wear data for nickel were used as a reference in laboratory wear tests. A correlation between circulation wear rates and laboratory wear rates formed the basis for a prediction of service life using relief legibility as an &apos;end of life&apos; criterion. This criterion was determined to be an average surface thickness loss of 12 um. The surf aces of nickel and Nickel-Banded-Steel (N-B-STM) coins were observed to harden both in circulation and in the laboratory tests at a rate of approximately I VHN/year of actual or simulated service life. It was also observed that the laboratory wear rate of N-B -S coins increased as nickel cladding thickness increased and this effect was attributed to differences in surface hardness.Wear test results are also reported for the new Canadian dollar coin material which shows a better wear resistance than pure nickel. IntroductionThe subject of coinage wear has a long history, and a number of studies have been published, concerned both with the measurement of circulation wear rates and with accelerated laboratory tests to simulate the behaviour of coinage materials in service. As early as 1803, wear tests were conducted by Hatchett on gold coinage using various types of vibratory and tumbling machines». These tests were commissioned by King George III of England who was concerned about the wear of gold coins in circulation.Early in this century, Adrian performed laboratory tests that showed that the wear rates of cupronickel 75/25 and nickel coins were in the ratio 3:1 and this ratio was later confirmed in laboratory tests reported by Daeppen and Zurrerw, The latter authors also weighed cupronickel and nickel coins that had been in circulation for various times and observed the same 3: I ratio. There was further support from Tylczak and Blickensderfer who reported significantly higher abrasive wear rates for cupronickel compared to nickel, when rubbed against sand paper."

Jan 1, 1988

By Michel Jébrak, Claude Bellehumeur

Abstract - Regional and orientation geochemical stream sediment surveys were carried out by the Quebec Department of Energy and Resources in southwestern Quebec, over a part of the Mont­ Laurier Terrane of the Grenville Province. The area contains some small stratiform zinc deposits. The response of Zn mineralization to geochemical surveys is weak; the known mineralization is not defined by anomalous samples and consistent patterns. This study uses a technique that increases the geochemical signature of Zn mineralization in filtering out geochemical background components related to lithologies and surficial conditions. The background variations were modelled using principal component analysis, and the filtering technique consists of the partial reconstruction of the data matrix from results of principal component analysis . The filtering procedure considerably enhances the Zn anomalies located in the catchment basins of Zn deposits, and defines some new anomalies in proximity to the marbles of the Mont-Laurier Terrane, the principal metallotect of Zn mineralization.

Jan 1, 1993

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999

By M. Piard

The scarcity of literature referring to mines in the Rockies has compelled the writer to co-ordinate information and advice taken at the very source. Help was gladly given by active inspectors and mine bosses. Although the field is unimportant at the present time, due to its distance from markets for raw coal, it is quite worthy of the attention it is receiving from two continents; for, with the commercial synthesis of liquid fuels, it would become the largest fuel laboratory in the world, provided, of course, that freight cost drops to a low comparative level. As explained below, there are no obstacles to economical and safe operation under anything like the typical outcrop shown in Figure 1. Although coal dust is probably more dangerous in the Rockies than anywhere else, the damp outcrops afford means of control. The abundant gas may be bled to the open air, and the rigid roof will settle gradually under a wide span of opened outcropping. The Panel Retreating Wall The Measures: Coal measures having an attitude similar to that shown in cross-section in Figure x are characteristic of the active coalfield on the Alberta side of the Rockies, and they are also found on large tracts of undeveloped land west of the divide. The small anticlines, not shown in the cross-section, do not affect the progress of a pillar line, provided their crests are connected to the atmosphere by drainage bore-holes.

Jan 1, 1928

By H. H. Bleakney

THIS paper presents evidence that in 3 1/2% nickel steel, the published temperature for the Ac1 transformation, l,275°F., represents the completion of that transformation, and that its inception occurs approximately 275°F. lower, at about l,000°F. The formation of austenite within this range, especially at the higher temperatures, and its subsequent decomposition to martensite, results in considerable impairment of the properties of the steel. That the solid solution found to occur below l,275°F. is austenite has been questioned, but the evidence herewith presented, while not decisive, appears to be reasonably convincing. INTRODUCTION The February, 1939, issue of Metals Technology contains a very interesting paper by I. N. Zavarine, Associate Professor of Metallurgical Engineering at the Massachusetts Institute of Technology. In that paper, Professor Zavarine presented photomicrographs illustrative of the microstructures produced by heating nickel steels to a temperature slightly below the carbon change point, and holding them at that temperature for various lengths of time. His illustrations show that the structures found after such treatment do not consist merely of ferrite and carbides, but are characterized by the presence of a third phase, which he describes as a&apos; &apos;sub-critical solid solution&apos;. The occurrence of this third phase in increasing amounts is accompanied by an increase in strength and a loss of ductility and impairment of elastic ratio of the steel. Some years ago, one of the authors encountered the above-mentioned phenomenon in treating large forgings of 3.5% nickel steel. After normalizing and then drawing at l,250°F., very poor mechanical properties were obtained. Investigation of the steel disclosed no inferiority in quality. Eventually, after considerable waste of time and money, a draw temperature of l,150°F. was tried. This treatment resulted in a very great increase in elastic ratio, over 5 per cent increase in percentage elongation, and proportionate improvement in reduction of area.

Jan 1, 1941

By Paul R. Terry

This paper presents a brief picture of the quality of coal produced in Eastern Canada for use in thermal generating stations. It describes, in particular, the characteristics of coals burned in six power plants -two in New Brunswick and four in Nova Scotia. Each station is dis-cussed in turn, and comments are made on the coals used therein with regards to origin and physical and chemical properties affecting station operation. A table of coal data shows, at a glance, the wide variation in the quality of coals received by these stations from producers in New Brunswick and Nova Scotia. "The promotion of improved coal quality for thermal generation can benefit our national economy." T HIS is the opening statement in a paper which was presented by Mr. D. A. Pirttinen at the Coal Division&apos;s Toronto meeting in April, 1960. In bringing the power engineer&apos;s viewpoint to the coal producers&apos; attention, Mr. Pirttinen made a survey of utility steam plants operating in Canada, and the results of this survey formed the basis for his paper, which he titled: "Generating Station Coal Quality.

Jan 1, 1965

By R. G. Burn

"A brief outline will be given of the concept of risk and its implications with regard to investment in exploration. The relationship between risk and decisions under uncertainty will be examined as a prelude to identifying those factors which contribute to exploration risks:consideration of the effects of corporate objectives (e.g. survival, expansion, diversification) on exploration strategy and ultimately on success or failure, exploration and mining as an investment (the relationship between risk and reward) and the desired return on investment; exploration odds, funding levels, staying power, financial exposure and the concept of gambler&apos;s ruin;origins of uncertainty in exploration decision-making-man-made risks and natural hazards; the nature of introduced constraints at each exploration decision stage and their effect on the rate of success;improving the chances of success and the invest reduction of risk through sound exploration strategy, effective project generation and efficient target detection capabilities."

Jan 1, 1984

Overview ?Oil Sands Background ?Water Use in Surface Mining ?Tailings Disposal ?Water Balance for Surface Mining ?Implications of Emerging Regulations ?Water Management Framework ?Tailings Performance Criteria (Directive 074)

May 1, 2009

By Marie-Eve Boucher

The slag in iron ore pellets allows wet sintering during firing and leads to suitable bounding. The process of slag formation differs whether it takes place in the core or in the external zone of a pellet. In the core, hematite can be reduced to secondary hematite, depending on the temperature and on the carbon monoxide/dioxide partial pressure ratio. The reaction rim that appears at the outskirts of a silica particle in contact with the FeO bearing magnetite is considered as the slag precursor in the core of the pellet. By contrast, in the external zone of a pellet, where O2 is available and CO partial pressure is very low, the first step towards slag formation is flux decomposition, mainly dolomite and limestone. The CaO liberated through this reaction will be available to react with hematite by solid diffusion to form calcioferrites, which play an active part in the slag evolution process. These two slag formation paths will be explained.

May 1, 2007

By L. T. Raevskaia

We discuss the stability problem of a piston of the reversible axial-piston pneumatic motor called DAR-14M. We performed the full analysis of stress and deformation characteristics of the piston near a resonant frequency with the help of FEM ANSYS. We estimated the own frequency of the piston analytically for the given motor, this estimate was confirmed numerically in the model analysis FEM ANSYS. It was also shown in harmonic analysis that loaded piston end behaves very different in comparison to the unloaded end. As expected, maximum deformation was found in the area of the holes of the bearing shaft, indicating an optimization necessary in that region of the motor.

Aug 1, 2013

By T. W. Wlodek, Zygmunt Kowalczyk

In the period from 1946 to 1964, the annual output of co al from Polish mines increased from 4 7.3 to 117.35 million tons. In this paper, the methods of bringing about this increase in productivity through the building of some twelve new collieries (producing some 15 million tons annually) and the modernization, reconstruction and extension of some thirty-six older collieries are discussed.

Jan 1, 1967

By A. I. A. Salama

The CANMET Western Research Centre (CWRC) has developed a hydrocyclone model simulation of dewatering and fine particle separation circuits. The simulation is based on an existing empirical model. Utilizing a cyclone manufacturer’s published data, some modifications have been developed and integrated into the model. Feed stream characteristics, cyclone mechanical dimensions, and operating conditions are used in the CWRC modelling simulation. The computer results are presented in 3D graphs and corresponding 2D maps showing the cyclone mass recovery, percent solids by mass in underflow and overflow, and cut size as functions of the cyclone apex diameter and cyclone throughput (i.e., inlet pressure or pressure drop). Results of the computer simulation have been used in the economic feasibility and design of several dewatering circuits in oil sand plants.

Jan 1, 2003

By Robert B. Parsons

"The junior mining company&apos;s bank account is depleted, but there are high hopes for the company&apos;s property. Where to get the necessary development funds is a common problem facing many juniors.This month, Tax Notes discusses briefly the principal income tax implications of several alternative development plans that are typically available to the junior mining company and its shareholders.IntroductionAt some point in time, many junior exploration companies face a common dilemma-a promising prospect has been proven up and is read y for further development, but alas, the company is flat broke! In this situation, a number of alternatives is available to the company, including the possibility of ""going it alone"" by raising capital through a public offering, or by striking a deal with a ""major"" or some other substantial investor.This article focuses on the latter possibility, and discusses in broad term s the main income tax implications of various arrangements between a typical junior exploration company and a larger public company for the development of a particular property. It will be appreciated that a discussion of other important considerations, such as those pertaining to securities exchange regulation s and company law requirements, is beyond the scope of this article.Jointly Owned CorporationPerhaps the simplest way of dealing with the problem of financing the development of a property is to sell the property outright, pocket the proceeds, and run! Clearly, though, this alternative is unacceptable to most prospectors and developers, who are predictably reluctant to completely relinquish their equity interest in a promising property. An additional strike against such an outright sale is that the sale could trigger an income tax liability. Generally speaking, in the case of a simple sale of a mineral property, for income tax purposes the proceeds are applied to reduce the taxpayer&apos; s unclaimed balance of Canadian development expense (""CDE""), with any unapplied excess being brought into income and taxed at ordinary corporate tax rates."

Jan 1, 1983

By Gavin Ritson, Chris Ward

"The oil sands industry is still fairly young with the first viable oil sand operation having been started in Alberta in 1960. Since then numerous modifications and improvements have been tried and implemented. The current process makes use of high velocity pumping of oil sands slurry with hot water (hydrotransport) to achieve separation of bitumen from the sand.A number of the oil sands processes have been adapted from unit operations that are used in mineral processing, such as crushing, screening, flotation, cycloning and thickening. This paper outlines a typical oil sands process flowsheet and investigates the differences and similarities in technologies and costs to other mineral processing industries. It also considers the very large throughputs required, and presents some of the difficulties and challenges currently faced by the industry as a result of high demand for oil and environmental pressures.INTRODUCTIONOil sands (also known as tar sands) deposits are found throughout the world. The Athabasca Oil Sands deposit in Aberta is the largest of these. Oil sands consist of a mixture of crude bitumen (a semi-solid form of crude oil), silica sand, clay minerals, and water. The Athabasca, Peace River and Cold Lake deposits cover 141,000 square kilometers and contain about 1.7 trillion barrels (270×109 m3) of bitumen in-place, comparable in magnitude to the world's total proven reserves of conventional oil"

Jan 1, 2009