Search Documents

By R. T. Saxon

Prior to November 1975 there were several failures of front -wheel spindles on large haulage truck s in B.C., attributed to fatigue cracks. Since that time, a non-destructive test program has succeeded in detecting the cracks before catastrophic failure, However, the author regards the failures as just one example of a. general unreliability in large high-strength steel castings and urges the industry to look to forgings for sensitive components of heavy equipment.

Jan 1, 1977

By K. Sasaki

Ventilation measurements were carried out in a shallow underground-quarry space with relatively large internal volume of 14,600 m3 in order to evaluate its effective ventilation characteristics. Based on air velocity measurements with an ultrasonic anemometer in the exhaust airway connected to the space, it was found that the space was ventilated by natural ventilation airflow with intermittent changes in direction. It was difficult to measure the ventilation flow with typical methods of flow measurement provided from the intake portal and throughout the mine, because the cross-sectional area and volume of the openings were too large and the flow was variable. In the present study, a tracer gas method was applied to evaluate the effective ventilation airflow rate in the space. A photo-acoustic infra-red gas monitor, highly sensitive to SF6 gas used as a tracer gas, was set in the space to determine air exchange rates from gas concentration-time decay curves. The seasonal variations of airflow and thermal environment in the space were investigated through 13 sets of measurements taken over 15 months. Airborne rock dust concentrations were also measured at same time in the opening. The correlations between the effective ventilation airflow rate, thermal environment and dust concentrations in the opening space were analyzed and are discussed based on the presented measurements taken during year. It is concluded that seasonal variations in effective ventilation flow and the dust concentration are mainly due to differences in air temperature in the space, as affected by the rock?s surface temperature and atmospheric temperature. In summertime, the air temperature and associated air density difference generated lower natural ventilation flows resulting in higher dust concentrations.

Aug 1, 2013

By E. Wright

"INTRODUCTIONThe Ruttan Mine is located twenty-two km east of Leaf Rapids in northwestern Manitoba. The copper-zinc exhalative massive sulphide deposit is comprised of a series of individual and interconnected en echelon lenses which strike east 20 degrees north and dip south 70 degrees. The mine has been owned and operated by the Hudson Bay Mining & Smelting Company since July 1987. Sherritt Gordon Mines Limited began mining the orebody in 1973 from an open pit, but production has been entirely from underground since 1980. HistoryDuring the progression from open pit to underground mining, it was recognized that manual methods of ore reserve calculation were inadequate for responding to changing metal prices and evaluating alternative mine plans. The mine planning system that was developed is described in the paper, ""Computerization of Ore Reserves and Mine Planning Functions at Ruttan Mine"", presented by B.C.W. Haystead at the 1984CIM Annual General Meeting. At that time, programs for core logging, diamond drill hole plotting, grade interpolation, ore outline digitizing, and reporting had been developed by the Systems Department for use on Sherritt's UNIVAC 1100 mainframe computer. Telecommunications linked terminals at the Ruttan coreshack and office to the UNIVAC in Fort Saskatchewan, Alberta. The same mine planning system was also used at a second property.Operation of the mine planning system was expensive, and it was evident that increased use required a costly upgrading of the UNIVAC in order to maintain an acceptable service level to all users. The system was re-evaluated,' and it was concluded that: core logging was not easily adaptable to a new property, nor flexible enough for exploration; plotting, grade interpolation, and digitizing required considerable manual effort; and that the UNIVAC operating system was difficult to learn.It was recommended that a study should determine if: core logging could be redesigned and/or implemented on a microcomputer; interactive graphics be used to reduce the effort for functions requiring visual interpretation; and the creation of input processors would assist users in setting up parameters for guiding the programs."

Jan 1, 1989

By Leiting Yue, Peng Ren, Yu Shen, Zhihong Liu, Haibao Shao, Longgong Xia, Feng Yu

The Kennecott-Outotec Flash Converting technology has been proven as an advanced and mature process in 5 individual plants during the past 2 decades. High grade copper matte (65–72%) produced in the flash smelting, or other smelting technologies is granulated to 3-5mm granules in a water torrent, and further crushed to fine powder (≈50µm) and dried to contain less than 0.3% H2O. Oxygen enriched air, together with fine copper matte powder and lime flux are injected into the reaction shaft by a matte burner. The copper making and slag making reactions will happen in very short time and distance during the particle falling and settling. However, industrial practice has found negative effects caused by sodium contamination. Na is introduced in the copper matte granulating process, and appears as Na2SO4 on particle surface. When Na content was high, scaling problems in the boiler will be worse, and the processing air will be blocked by the growing accretion around the matte burner, and as-produced blister copper is always high in S and O. In this present study, an industrial matte sample was used in the experimental work. Na was introduced into the matte powder by Na2SO4 solution soaking. The burning behaviour of the doped copper matte powder has been investigated as a function of the impurity concentration and processing temperature. Morphology and composition of these samples explained how Na2SO4 converts and reacts in the oxidizing atmosphere, and how they or their converting species influence the burning behaviour of matte particles. Cross-sections of as-prepared samples were analyzed with SEM-EDS, and the reaction mechanism has been carefully interpreted. Results from the present study can benefit both academic and industrial people. INTRODUCTION "Flash Converting" technology was developed jointly by Kennecott Utah Copper Smelter and Outotec (Finland) OY in 1992. The first industrialization of the technology was in Utah Smelter in 1995. Since 2006, it has been successfully applied in Xiangguang Copper, Tongling Jinguan Copper Branch, Fangchengang Jinchuan Copper, and Ningde Southeast Copper. The technology has also been further developed in those smelters. At present, roughly 2 million tons blister copper is produced annually through the Kennecott-Outotec Flash Converting technology, accounting for more than 10% of global primary copper production. The technology has advantages of high efficiency, high sulfur capture rate, good in environmental issues, mature equipment supporting, high automatic control level, low comprehensive energy consumption and flexible connection with the smelting unit, which make the technology to be one of the best choices in investing a new large-scale copper smelter or updating an old copper project in the world.

Jan 1, 2019

By M. Nejati, A. Paluszny, R. W. Zimmerman

A numerical method is proposed to propagate multiple discrete fractures leading to primary fragmentation in a mine that is being worked using block caving. Deformation is computed using the finite element method, fractures are represented explicitly, and the mine domain is discretized by an unstructured mesh. Bedding planes are represented by systematically varying the elastic modulus of the rock and by defining horizontal weakness planes. Fractures and matrix are represented using parametric surfaces, and tips are defined by their boundary curves. Tip advance is controlled by a failure criterion, and a criterion for propagation direction and magnitude, based on the evaluation of the modal stress intensity factors. A novel domain integral approach is applied to accurately compute stress intensity factors (K) ahead of fracture tips in three dimensions. The method does not require a structured volumetric mesh structure around the crack tip, as integration is performed over a series of virtual surface domains along the crack front. The method is efficient, as it makes direct use of automatically generated, arbitrary tetrahedral meshes, and approximates stress intensity factors (KI, KII, KIII) along each crack front using Interaction-integrals. As opposed to the JIntegral, the method does not decompose K a-posteriori, but instead uses an auxiliary field to directly compute modal K. When using this method, numerical approximations of K do not exhibit dependence on the mesh layout, and require meshes that can generally be ten times coarser than are required by displacement- and stress-based methods. Volumetric meshing requires only, on average, 17% of each computation step. Thus, cracks do not follow any pre-existing mesh structure, and the method is well suited for high-density fracture datasets. The method is demonstrated for primary fragmentation of a mine area covering 110 initial draw points, immediately beneath a 2m high undercut. Displacement is constrained at all boundaries except the surface of the undercut. The growth of the fractures is investigated at the onset of the undercut. Ninety initial disc-shaped fractures are taken into account, each having an initial radius of 10 m. Fractures grow around the undercut, intersect the bedding plane boundaries, and the domain is fragmented as a result.

Jan 1, 2015

By J. W. Choung, T. Fu, Z. A. Zhou

An on-line visualization technique and methodology was developed to investigate the role of fine sphalerite (< 10 um) aggregation in flotation. The images of particle aggregates under different operating conditions were recorded and analyzed. The effect of impeller design on particle aggregation was demonstrated. This difference was not mainly due to the energy input into the system, but due to the resultant hydrodynamic conditions created by the impeller and their effect on particle interactions. The recorded image showed that adding fine silica (- 5 um) did not interfere with fine sphalerite aggregation, thereby showing no effect on the sphalerite recovery. Effect of the enlarged aggregate size on increasing flotation recovery was confirmed. Although Malvern Mastersizer produced consistently lower estimates of aggregate size than those by the image analysis, both methods responded to the changes in operating conditions in the similar trend. It was shown from this study that on-line visualization technique is a powerful tool for studying fine particle aggregation and morphology in the context of diagnosis for the flotation separation.

Jan 1, 2004

By J. W. Spyker, D. H. Filson, W. H. W. Husband

"Large deposits of sodium sulphate exist in southern Saskatchewan in the brines or muddy crystal beds of alkali Jakes. Currently, more than 300,000 tons per year of sodium sulphate are produced from these lakes and sold as salt cake to the paper industry. Most of the production is obtained from the brines of a limited number of Jakes.The Saskatchewan Research Council was requested to develop a process for recovering sodium sulphate from the muddy crystal beds so that this type of deposit could be exploited in the future. A flowsheet was developed with the aid of phase diagram data and the process was studied on a pilot-plant scale using raw material from three different lakes. Satisfactory yields and product purities were obtained in all cases, and an economic analysis indicated that a 100,000-ton-per-year sodium sulphate plant could produce salt cake at a cost of $12.26 per ton for a rate of return upon investment of 16 per cent at current market prices."

Jan 1, 1966

By F. E. Lee

The following outline gives a brief account of some of the ways in which microscopy is applied to the problems arising from the various operations of the Tadanac reduction works, at Trail, B. C. The Sullivan ore is a very fine-grained mixture of galena, marmatite, pyrite and pyrrhotite. The separation of minerals associated so intimately is a difficult task and requires careful control. Various oils and reagents are used in the process as developed, and it is essential that the operators have a means of control which shall be rapid, and at the same time, approximately correct. This result is obtained by microscopic analysis in the following manner: The operator places a quantity of the material upon a slide, a drop of water is added, and it is covered with a cover glass. Upon examination with transmitted light, the zinc mineral particles appear reddish, the ordinary gangue colorless, the lead and iron sulphides opaque. This method has proved of great assistance both in the development and in the operation of the present method for concentrating Sullivan ore. The miscroscope has thus become as much a part of the metallurgical equipment as the balance and burette. The microscope used in the laboratory is a Fuess "petrographic" with a specially-made vertical "illuminator" by Bausch & Lomb, with the usual accessories.

Jan 1, 1924

By Michel Doyon

Canadian Context: Exploration ??Space Exploration is within the unique mandate of the Canadian Space Agency ??Global partnerships ??Maintain close relationship with our partners ??New knowledge in S&T ??Retain and attract highly qualified personnel ??Participation in missions leads to design roles in industry and academia ??Collaboration between government laboratories, industry and academia

May 1, 2009

By D. Stone, N. J. Aslin, W. Webb

In today&apos;s modem copper electro-refineries, increasingly higher average current densities are being employed. With these increases many refineries are approaching their limiting current density. The nearness of the average operating current density to the limiting current density has placed increasing emphasis on the need to maintain an even current distribution. This paper explores the importance of maintaining even current density and discusses the factors, processes and practices that are necessary to achieve and maintain high quality production at high operational intensity.

Jan 1, 2005

By Sam Palombo, James José Varela

"Washing can be defined as the process used to eliminate or reduce the dirt (presence of fines or slimes) of one material. It is also the basic and oldest process applied to ore preparation for further concentration. This process, in combination with commnution and screening, form the so called washing plant and in many cases produce end products. This work describes the factors that influence the performance of the washing process and main washing technologies used in the mineral processing industry.The Hydro-Clean represents, since 1998, a state of the art technology in this area and is comprised of one of the most innovative solutions developed at HAVER & BOECKER. HAVER & BOECKER design and manufacture technology for mining and related industries. Today the Hydro-Clean is manufactured and sold throughout the Haver Screening Group (HSG) which is comprised of HAVER & BOECKER Maschinenfabrik Münster, HAVER & BOECKER Latinoamericana – Brazil and W.S. Tyler Canada.The Hydro-Clean is a washing technology based on utilization of high pressure water jets. To follow we will discuss how the Hydro-Clean’s different modes of operation result in several advantages related with mine waste reduction, recovery of saleable product, lower capital costs, superior washing results, less stress for the material, a wider range of application and less maintenance cost. Aside from these positive factors, its lower operation costs related to the consumption of energy and water are presented. It is important to note that the quantities, tonnages, data and management concepts presented in the paper are accurate for the time of writing and are subject to change and modification as operations progress."

Jan 1, 2009

By Subrata Dutta

Sindesar Khurd Mine is situated in Rajasthan, India, and operated by Hindustan Zinc Ltd, under Vedanta Group. The base metal mine is high in reserves of Lead, Zinc and silver and has been producing since 2007 with initial production of 0.3 mtpa. Recently the mine has gained prominence as a base metal underground mine in introduction of latest mining techniques and achieving high production at lowest costs. The promising Lead-Zinc reserves of Sindesar Khurd Mine (SKM) and high-tech exploration adopted by Hindustan Zinc Ltd (HZL), (Vedanta Group), raising the reserves and resources from a meager 9 Mt (1997) to 81 Mt (2012), has prompted HZL management to ramp up the mine production from 0.3 mtpa (2006-07) to 2 mtpa by 2013-14 with ambitious plans to reach 3.5mtpa subsequently (presently largest underground metal mine in India). The complete trackless system underground mine, recently equipped with latest leaky feeder communication system (unique in India), utilize modern drilling, mucking and hauling equipment aided with various utility/service vehicles. Excavation optimization and quality recovery maximization from the open and post filled stoping methods, continual expert analysis and feedback from International consultants like AMC (Australia) and SRK (UK), and involvement of renowned bodies in management excellence, have lead the mine towards highest productivity and lowest mine operating cost, earning the mine a prominent place in the global base metal industry. The paper deals with how the various challenges in mine planning and designing, mine development, operator skill, equipment introduction and maintenance, expertise availability, provide training and exposure to officials, prompt and effective communication/service, control of ground vibrations, maintain ventilation standards etc are faced in attaining high operational excellence and thus attain a record mine output/man shift (OMS) of 14 ton/man shift with targets to reach 20 ton/man /shift. Scientific designing using 2D/3D numerical mine-modeling techniques, faster stope sequencing with introduction of paste filling ( first time in India),latest leaky feeder communication system, control ground vibration to stringent standards using electronic delay system, faster raising techniques using raise borers to enhance development and ventilation, cavity scanners to monitor large stope voids, fast shaft sinking at 100 m/month(Chinese expertise) and maintaining adequate ventilation with close software monitoring are some of the highlights discussed in the paper towards achieving the targets.

Aug 1, 2013

By Douglas R. Piteau

"Assessing the stability of a slope cut in rock is basically a problem of engineering geology - geology, because it involves a sound understanding of the important aspects of geology, such as geological structure, ground water, weathering and other natural phenomena, which all relate to or exist in a geological environment, and engineering, in that quantitative evaluations and calculations are necessary, these being based on mechanics and relating to the strength of the geological materials and the forces causing instability of the slopes. The engineering geologist must make every attempt to. provide, in a quantitative way, information on those geological factors which are necessary for making calculations of the probable stability of the slope. These include numerical assessments of quantities relating to the characteristics of structural discontinuities, rock types, topography, hydrogeology, tectonic history and other environmental factors. Based on the development and extension of these general principles, both preliminary and final slope stability studies of some open pits in South Africa, Swaziland and Zambia have been conducted. Some of the basic concepts and techniques developed to carry these studies out are described."

Jan 1, 1972

By M. Rizwan

Mine workings are progressing to greater depths as shallow mineral resources are being depleted, and civil engineering projects are nowadays being developed at substantial depths. The threat to tunnel stability posed by rockburst events has increased as a result of these high stress environments. Rockbursts are violent events capable of mobilizing large volumes of rock. In addition to the threat to safety and equipment, rockburst damage can significantly impact on operations, and cause loss of mining production, often the largest cost component of such events. Rehabilitation of such damage requires significant effort and resources. Tunnel walls and roof are usually well supported, but the installation of rock support in the floor is uncommon, particularly in mining environments. In the absence of rock support, floors of the excavations are vulnerable to rockburst damage. New concepts for containing damage of excavation floors by dissipation of the large transient forces using simple techniques or preselected and designed elements of sacrificial floor systems are presented. Two approaches to calculate the demand are presented: estimating load demand by assuming displacement levels and a response modification factor; and using a limit displacement approach to calculate elastic stiffness of the selected elements of the sacrificial support system. The proposed conceptual support systems have the capability of dissipating rockburst energy while retaining sufficient serviceability. It is considered that the concepts presented, for discussion, in this paper are logical and developable into practicable and economic solutions for tunnel floor support in rockbursting environments.

Jan 1, 2015

By F. D. Ford, Z. Dai, A. Byers

Manitoba Mining and Milling operations consist of three underground mines (Thompson T1, T3 and Birchtree), feeding the Thompson Mill. Three years ago, a collaborative effort involving Mines Exploration, Mines Project Development Group, Mill Technical Services and Vale Base Metals Technical Excellence Center was initiated to establish and verify the cause of high variability in concentrate quality and Ni recovery at the Thompson Mill. One outcome of this work was a program to systematically characterize the mineralogy and metallurgical performance of current and future orebodies feeding the mill. Mineralogy results show that high value enabling ores typically have a high pentlandite to pyrrhotite ratio and benign silicate mineralogy (mostly quartz and feldspar from sedimentary host rocks), while metallurgically challenging ores contain some combination of pyrite and/or hexagonal (non-magnetic) pyrrhotite and/or elevated quantities of talc (with associated carbonates) derived from altered ultramafic host rocks. The metallurgical performance of these two ore types has been simulated by an Excel particle flotation model, which calculates the relative floatability of particles based on the particle’s mineral composition and mineral locking determined from MLA images. The relationship between these mineral properties measured by MLA and metallurgical performance was established using 13 monthly composite samples from Thompson Mill. The model was then validated with results of laboratory flotation experiments on individual orebodies submitted for evaluation. The validated model can be used to predict plant metallurgical performance based on individual ore bodies feeding the mill. Individual orebody’s grade-recovery curves are assumed to be additive, and can be weighted in proportion to the mill feed to predict mill recovery over the same time period. The ore mixing can be done with a simple Excel spreadsheet and comes with a graphical output for easy visualization of the resulting grade-recovery curve.

Jan 1, 2015

By S. Maleksaeedi

On-site evaluation of strength using hardness is common for different materials. The lack of such relation for aluminum alloys has always been felt. In this work, a finite element analysis of plastic deformation and its distribution in Brinell hardness testing is presented. The analysis has been performed for different strength levels of aluminum alloys. By utilizing the Von Mises equivalent strain in hardness, it is tried to derive a correlation between hardness and strength values for the alloys under consideration. The derived correlation is verified using the experimental values available in literature.

Jan 1, 2004

By R Thomson

The use of uranium metal in non-ferrous metallurgical practice is dis-cussed with reference to its alloying behaviour and chemical activity. It is suggested that the more promising applications are in the treatment of molten metals to combine with impurities. Mines Branch work along these lines is described for copper, zinc, magnesium, aluminum and nickel alloys. It is shown that a cop-per-uranium master alloy (25 per cent U) successfully deoxidizes molten copper without detriment to the electrical or mechanical properties of the product at residual uranium levels of up to 0.8 wt. per cent. Additions of uranium to alpha brass in amounts greater than the lead impurity content were found to remove the deleterious effect of lead on hot-workability. Similar deoxidizing and malleableizing effects were found with uranium additions to nickel. It is thought that uranium forms stable intermetallic compounds with many impurity elements. A significant malleableizing effect can therefore be expected in the presence of other elements besides lead.

Jan 1, 1963

By Adrian Dance

Newmont Ghana Gold Limited?s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto- Mill projects, PTI?s methodology is termed Process Integration & Optimisation (PIO). Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit. Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended. A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI?s SmartTag? system. The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material. This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput.

Jan 1, 2012

By E. Michelotti, M. Cardu

This paper presents the results of a new method that has been tested to recover metallic cobalt lost by diamond beads from rock cuttings. When dimension stones are cut using diamond wire saws, the beads become worn and, before the end of their cycle life, lose a certain amount of material; this material is prevalently made up of sintered metal and diamonds. The material is then washed away, together with rock debris, in a dilute pulp. In effect, this process involves the dispersion of economically valuable, but potentially polluting, materials (such as cobalt) that are used to confer indispensable technological features to the beads. This current research aims to develop a waste-processing pilot plant (High-gradient Magnetic Separator or HGMS) to recover metallic components from the pulp by means of a suitable separation. The research\u2019s purposes are two-fold: a. to remove the polluting components from the rock debris before their disposal and b. to start a recycling process of the valuable metals.

Jan 1, 2010

By Kim H. Shikaze, John R. Hawley

"Even though acid mine drainage is an old problem, particularly in coal mining areas, its appearance in the form of a major environmental hazard in the hardrock mining districts of Ontario was unexpected. The yellow and amber coloured wastes that characterize an acid mine drainage situation were first noted by the Ontario Water Resources Commission in the uranium mining Elliot Lake district. Problems of a similar nature were also noted in the copper-lead-zinc camp at Manitouwadge, the nickel camp at Sudbury and at numerous isolated base metal properties, both in and out of the Province of Ontario.Without exception, when acid mine drainage type effluents were evident, the specific companies involved worked sulphide or sulphide-associated ores. Without exception, the ore bodies contained quantities of iron sulphide (in various mineralogical forms) and, without exception, the milling circuits serving these operations were such that the iron sulphides were rejected to the tailings areas as waste.Once in a tailings area and after a varying period of time, iron sulphides react to form water soluble salts which, when discharged in the effluents from the tailings area, can affect stream chemistry and stream ecology.It is not unusual that the minerals pyrite, marcasite and pyrrhotite (all iron sulphides) react to form a stable oxide under atmospheric conditions. The law of stability of rocks and minerals, for instance, states that rocks and minerals are stable only in the environment of their formation and, as the environment surrounding them changes, the rocks and minerals tend to change to other species which are relatively more nearly stable under the conditions of the new environment (a). Under atmospheric conditions, iron oxide exhibits a greater stability than iron sulphide."

Jan 1, 1971