Search Documents

By Richard Mcivor, Largo Albert

"Inco Limited has operated aluminum mine shaft conveyances since 1968. Aluminum conveyances are used where the hoisting in system requires lightweight conveyances to maintain the hoist rope safety factors and mine hoist rope pulls as dictated by government regulations. Inco Ltd. currently has 20 skips (including spares) operating in the Ontario Division mines. The main problems encountered are with galvanic corrosion between dissimilar metals and metal fatigue. This paper will highlight some of the problems encountered and illustrate methods utilized to overcome the problems and improve the conveyances performance.IntroductionAluminum mine shaft conveyances have been in use at Inco Limited's various Sudbury district mines since 1968. All of the conveyances currently in use are skips used for hoisting mine ore and rock. Inco had an aluminum quick change Kimberley-type skip and cage in operation at its Totten Mine in the early 1970s, but this mine is no longer in operation and no further comment will be made.The primary reason why aluminum conveyances are chosen over conventional steel conveyances is because of their light weight. Typically an aluminum conveyance will weigh about 60% to 70% of a steel conveyance of similar design. The lighter weight conveyances will allow higher payloads to be used and still maintain the statutory hoist rope factors of safety. It must be remembered that increasing the payload will increase the power required to raise the load and the hoist will have to have the necessary horsepower for the increased payload or the system will be overloaded.The front dump (Rola-chute) skips are of the bail-less design, i.e. the box structure also supports the load and has the shaft guide shoes attached directly to the side of the box structure. The Copper Cliff North Mine and South Mine skips have a joint in the centre of the conveyance and are installed in the shaft in two sections and connected with pins. This feature allows very long (42 ft) skips to be used in areas where a one-piece bail-type conveyance could not be installed. It is not practical to make sectionalized bail-type conveyances"

Jan 1, 1988

By Jonathan Allen, Peter Radziszewski

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. The year 1948 saw the successful application of DuPont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding. In the context of the mining industry, smaller grain size and other mineralogical characteristics have motivated the need to grind finer. In order to address this need, the interest in stirred milling technologies has grown over the last 20 years as can be illustrated by the large body of literature published over this same period of time. The typical observation reported in the literature is that in certain circumstances stirred milling is significantly more efficient than ball milling. Despite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills. The aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of how power and energy is affected by stirred mill impellor design and mill operation. This will be accomplished by first completing an overview of the power models found in the literature followed by a general description of DEM and CFD stirred mill models as well as the insights that can be drawn from them. Finally, a generic stirred mill power model will be presented and applied to different stirred mill types in order to develop some insights into the differences between different mill types. The paper will close with a discussion on some of the challenges that these models have and how future research might contribute to overcoming them."

Jan 1, 2014

By D. Komljenovic, J. Paraszczak

"This paper presents the use of queuing theory in truck fleet sizing in open pit mining operations. In the first part, a methodology is developed by which an optimal ratio between the size of shovels and trucks may be determined. The second part gives the fundamentals of the queuing theory and its application in analyzing shovel and trucks. The stochastic character of involved times (loading, truck cycle, etc.) is taken into consideration. Using the above theory, the optimal truck fleet size in actual conditions may be estimated. Minimal operating cost of the working system (shovelstrucks) represents the basic requirement of the analyzed process. The methodology was validated on Caterpillar front-shovel – truck combinations. IntroductionLes camions représentent probablement les équipements les plus utilisés pour le transport dans les mines. Le coût de transport peut parfois atteindre 50 % du coût d’exploitation et 25 % du coût total (Collins, 1996; Kennedy, 1990). Il est critique pour une opération minière de le minimiser. C’est un sujet qui a été traité relativement souvent dans la littérature spécialisée. Les premières applications informatiques dans l’industrie minière ont été développées pour la détermination du temps de cycle des camions.Au fil des ans, la capacité des camions a augmenté et, aujourd’hui, les plus gros manufacturiers de camions (Caterpillar, Orenstein & Koppel, Euclid, Terex, Unit Rig, Komatsu, Liebherr, Belaz) fabriquent des camions ayant une capacité de 200 t et plus dont quelques-uns d’une capacité supérieure à 320 t. Pour les plus gros camions, le coût d’opération peut même dépasser 240 $US/heure dans des conditions modérées (Caterpillar, 1999). Les mines modernes de grande taille peuvent posséder plusieurs dizaines de camions dans leur flotte."

Jan 1, 2004

By P. A. Witt

"Highland Valley Copper is a conventional truck-shovel mining and flotation concentrator operation located 75 km southwest of Kamloops, British Columbia (Fig. 1).The ore is situated within a porphyry copper deposit and is mined at a rate of 135,000 mt/day from two separate open pits. The nearby mill produces concentrates containing 375 million pounds of copper and 5 million pounds of molybdenum metal yearly. In the Valley pit, head grades are roughly 0.40% Cu at a 0.23% Cu equivalent cut-off. The Valley pit strip ratio currently sits at 0.55:1 with waste quantities made up of separate rock and unconsolidated overburden units. From the mill, concentrates are trucked to nearby Ashcroft and then hauled by rail to ocean port facilities in Vancouver. The mine employs 950 people and is planned to operate until 2009. The operation is a partnership between Teck Cominco (63.9%), BHP Billiton (33.6%), and others (2.5%). Management is shared by the two principal owners and directed by a management committee."

Jan 1, 2005

By James F. Archibald, H. Jame Hackwood

"Research was performed to assess the feasibility of barrier membrane substances, for use within mining or associated high risk environments, in restricting the diffusion transport of radon gas. Specific tests were conducted, both within laboratory and in situ environments, to determine radon gas concentration ratios across a barrier of interest and emanation rate variation resulting from application of such materials. Several materials have been demonstrated to be effective in restricting the emanation of radon gas into initially radon-free environments. One liquid material shows particularly good promise upon consideration of ideal radon barrier criteria.IntroductionIt has long been known (I.2.3) that inhalation of the short-lived, alpha particle-emitting daughters of radon gas can result in irradiation of lung tissue with the potential for causing lung cancer. Control measures are necessary to maintain concentrations of airborne contamination at a minimum to protect miner health and safety. Typical control practices in mines have been through the application of systematic ventilation and backfilling of excavated opening. As mines become deeper, however, and additional workings become exposed, increased ventilation capacity requirements are needed. As an alternative to other radiation control measures, the use of sealants to prevent radon migration from walls into mine atmospheres may provide a suitable engineering alternative."

Jan 1, 1987

This paper describes the back analysis of the Pavoncelli tunnel, an hydraulic tunnel which was excavated between 1904 and 1915 in South of Italy and experienced severe damages during the 1980 Irpino-Lucano earthquake. A numerical simulation which is intended to study the behaviour of the tunnel during this seismic event is presented, also accounting for the swelling phenomenon that took place during and after construction.

May 1, 2009

By E. N. Gilje

"IntroductionDURING the past five years, over two miles of shaft sinking have been completed at Falconbridge. As sinking has continued, we have improved our equipment and technique with a resulting increase in efficiency. Throughout this period, all sinking has been done by contracting firms, under our direction and to our equipment specifications, with highly satisfactory results. Since 1949, Riddell shaft mucking machines have been successfully used in conjunction with the •benching method of sinking. Our most recent practice can best be illustrated by describing the method used in sinking No. 1 shaft at the Fecunis Lake mine.No. 1 Shaft, Fecunis Lake MineNo. 1 shaft, consisting of six compartments and measuring 13 ft. 11 l/2 in. by 19 ft. 9 3/8 in., outside timber (Figure 1), will be sunk to a depth of 4,170 feet. It was designed to accommodate two 10-ft.diam. Koepe hoists."

Jan 1, 1955

By Tatiana Ravani von Ow, Leandro Bomvisinho

"The size of mills driven by ring-gear or by a gearless solution has significantly increased in the last years. This has created additional challenges for the driven equipment. The requirements for the mechanical devices and the power grid have become more demanding. Controlled soft starting and operation, especially in dual pinion mills, as well as the protection of the equipment has gained importance. The selection of the drive solution for the mill therefore becomes more critical. Besides the classical criteria such as performance, efficiency and capital costs other factors come in the evaluation of the system such as flexibility and optimization of operation, reliability and the ageing of the grinding equipment.Variable speed solutions offer significant advantages over conventional fixed speed drives due to their application specific features and process optimization capabilities, even for ball mills where these are not seen yet as a must.The initial capital costs are higher than some of the direct on-line solutions however the benefits for the operation during the lifetime of the mill generated by the use of converter solutions justify the additional higher investment.INTRODUCTIONThe method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said; almost every decade in the last half century had its own trend. The trend was dominated by the market demand, by the process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology.All has started about 50 years ago with mill diameters less than 20 feet driven by fix speed synchronous or wound rotor motors with the power of about 2 MW. Around 10 years later, the mill sizes increased, but the necessary torque could not be transmitted by one pinion therefore dual pinion solutions were developed to power the mills. However, realization of the dual pinion solution was only possible when load could be evenly shared between the two pinions."

Jan 1, 2010

By I. Campbell, P. C. Jones, E. G. Potter, R. P. Taylor

"The Cobalt embayment is a large domain of Paleoproterozoic clastic sedimentary rocks that unconformably overlies the Archean Abitibi greenstone belt. Regionally extensive sills and dikes of Nipissing diabase, emplaced circa 2219 Ma, occur throughout the embayment and are the preferential host to gold-bearing polymetallic vein systems on the Merico-Ethel property, near the northeastern margin of the Cobalt embayment. These gold-bearing, polymetallic veins are predominantly east-west-trending, steeply dipping, discordant calcite- quartz vein systems that formed close to the time of crystallization (within ~15 m.y., based on Pb-Pb ages) of the Nipissing diabase. The ore mineralogy is complex in character, typically comprising sulfides, arsenides, native metals (gold and silver), and specular hematite, preferentially concentrated along the interface between silicate and calcite gangue. A simplified sequence of mineral deposition in the veins is: (1) "Early-stage" pyrite ± chalcopyrite hosted in quartz ± chlorite gangue; (2) "Main-stage" polymetallic (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U) sulfides, arsenides, and native metals hosted in calcite gangue; and (3) "Late-stage" calcite flooding ± galena. Wall-rock alteration in Nipissing diabase is restricted to narrow (<5 cm) haloes of calcite-chloriteepidote- bearing assemblages, whereas a weak alteration halo of specular hematite, calcite, and allanite-epidote has been observed in the surrounding sedimentary rocks. In terms of their age, geology, mineralogy, paragenesis, and morphology, the gold-bearing vein systems at Merico-Ethel closely resemble the silver-sulfarsenide vein deposits of the historic Cobalt and Gowganda mining camps. These observations indicate that the Au-bearing veins are variants of the Ag-vein systems and as such, have a common genesis belt. L’Échancrure de Cobalt est un large domaine de roches sédimentaires clastiques d’âge Paléoprotérozoïque qui reposent en discordance sur la ceinture de roches vertes d’Abitibi d’âge Archéen. La Diabase de Nipissing, mise en place vers 2219 Ma et qui constitue un réseau de sills et de dykes d’importance régionale, est présente dans l’ensemble de l’échancrure et constitue la roche-hôte principale des systèmes de veines aurifères-polymétalliques de la propriété Merico-Ethel, près de la bordure nord-est de l’Échancrure de Cobalt. Ces veines à minéralisation aurifère et polymétallique constituent un système de veines de calcite-quartz sécantes d’orientation principalement est-ouest et à pendage fort qui se sont formées peu de temps après la cristallisation de la Diabase de Nipissing (à ~15 Ma près, d’après les âges Pb-Pb). La minéralogie de la minéralisation est complexe; elle consiste typiquement en sulfures, en arséniures, en métaux natifs (or et argent) et en hématite spéculaire, préférentiellement concentrés à l’interface entre les silicates et la gangue de calcite. La séquence de déposition simplifiée des minéraux dans les veines est : (1) «Stade précoce» pyrite ± chalcopyrite encaissés dans une gangue de quartz ± chlorite; (2) "Stade principal" sulfures polymétalliques (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U), arséniures, et métaux natifs dans une gangue de calcite; et (3) "Stade tardif" calcite massive ± galène. L’altération pénétrative de la Diabase de Nipissing est confinée à des halos étroits (<5 cm) présentant des assemblages marquées par la présence de calcite-chlorite-épidote, tandis qu’un faible halo d’altération en hématite spéculaire, calcite et en allanite-épidote est noté dans les roches sédimentaires environnantes. De par leur âge, leur géologie, leur minéralogie leur paragenèse et leur morphologie, les systèmes de veines aurifères de Merico-Ethel ressemblent beaucoup aux gîtes filoniens d’argent-sulfoarséniures des camps miniers historiques de Cobalt et de Gowganda. Ces observations indiquent que ces veines aurifères constituent une variante des systèmes des veines argentifères et qu’elles partagent"

Jan 1, 2009

By Donka H. Andreeva

Gold catalysts based on different supports, titania, zirconia, ceria and mesoporous titania and zirconia, nonpromoted and promoted by vanadia in the reaction of complete benzene oxidation have been studied. XRD, HRTEM, TPR, Raman and ESR spectroscopy were applied for the characterization of the catalysts. The influence of gold on the reduction behavior, state and structure of vanadia on the surface was studied, as well as the role of supports nature on the properties and catalytic activity. A strong synergistic effect between gold and vanadia was observed for the all studied catalysts with an exception of the catalysts supported on mesoporous zirconia. In the last case the catalysts containing gold and gold-vanadia exhibit high and equal catalytic activity. The catalysts on ceria show highest and stable catalytic activity in the studied reaction among the all studied catalysts.

Oct 1, 2003

The uphole bench extraction strategy at EKJV Management Pty Ltd?s Raleigh Mine, requires simultaneous horizontal and vertical exposure of paste filled stopes. In order to prevent excessive ore dilution, the paste fill must be of sufficient strength to prevent failure during exposure. A numerical modelling methodology has been developed to accurately simulate the initial stress distribution within paste filled stopes, together with the strain-softening loading response of paste fill material. Due to the narrow orebody width and high deformation behaviour of the host rock mass, high closure strains are likely to cause a stiff, brittle fill material to undergo crushing failure upon exposure. The stability of paste fill exposures at the Raleigh Mine was determined by conducting a series of three-dimensional numerical models that incorporate the extraction, filling and exposure sequence of paste filled stopes. Stability charts for 2.5 m and 3.5 m wide simultaneous horizontal and vertical exposures have been derived based upon the numerical modelling results. Implementation of the stability charts has proved successful in limiting the amount of ore dilution from paste fill and provides a basis to optimize paste fill cementation and stability throughout the life of the mine.

May 1, 2007

By Stuart McTavish

"Noranda's Goldstream mine is a 1,500 ton per day copper-zinc mine located 60 miles north of Revelstoke, B.C.The orebody which contains 3.69% Cu and 2.69% Zn was discovered in 1972. Construction of the mine and mill was completed in 1982 and start up was achieved in May 1983.This paper will describe the flowsheet and related equipment 1n the crusher and mill, in particular the dewatering section where two Larox pressure filters are used to dry the concentrates.INTRODUCTIONThe Goldstrean property is located 60 miles north of Revelstoke, B.C. in the Goldstream River Valley (Figure #1). It was discovered during the construction of a logging road in 1972. Exploratory drilling was initiated in 1975, and in 1976 a portal was collared to obtain underground data. Samples were taken from the underground workings for metallurgical bench tests and a pilot plant run.Due to economic conditions, the decision to go into production was delayed until 1980. Concentrator construction and underground development progressed simultaneously during 1981 and 1982, and were completed by the end of 1982. Start up of the concentrator was achieved on May 2, 1983.The ore typically contains about 40% sulphides, which are chalcopyrite 10%, sphaletite 6%, pyrrhotite 20%, and pyrite less than 5%. The sulphide minerals have a high degree of intergrowth. Most of the sphalerite occurs in micron sized grains which are embedded in the pyrrhotite and, to a lesser degree in the chalcopyrite. There is also some fine dissemination of the chalcopyrite in the pyrrhotite. The waste rock is made up of about 30% quartz, 20% guange silicates, and 10% carbonates. The ore has a specific gravity of 3.2 and a natural pH of 8.2."

Jan 1, 1985

By Persio P. Rosario

Crushing has proven to be of fundamental importance in mine mill integration at Highland Valley Copper (HVC). Highland Valley Copper has achieved large throughput and good quality control through the gyratory crushers by proper blast design and better gap control. The next step, in optimizing the mine mill relationship, is evaluating the crusher liner wear and its shape influence on performance and product size reduction. To do this a laser measurement device has been developed and data is being recorded on the concave and mantle liner wear. This paper will outline the work to date and indicate specific objectives of the work.

May 1, 2002

By P. Brad Marchant

"To properly evaluate bioleaching as a commercial alternative for sulphide concentrate oxidation, to enhance cyanidation response, it was necessary to define and optimize critical operating variables outside of the laboratory under less than ideal conditions. A complete bioleach testing laboratory was installed at Equity Silver Mines to aid in pilot plant flowsheet development.A continuous pilot scale bioleach circuit was constructed to provide data for meaningful valuation of biotechnology on a plant scale. The important operating and design parameters for pilot plant testing are described. Plant scale feasibility and design considerations, to treat a refractory pyrite/arsenopyrite concentrate produced from flotation tailing, are discussed. 1.0 BACKGROUNDEquity Silver Mines Limited is located 37 km southeast of Houston in central British Columbia. A 70% owned subsidiary of Placer Development Limited, Equity is Canada's largest open pit silver producer. Ore reserves were estimated at 28 million tonnes grading 106 g Ag/t, 0.96 g Au/t, and 0.38% Cu from two pits, the Southern Tail and the Main Zone. Detailed geology and mineralogy has been described previously(1,2).The concentrator flowsheet consists of conventional crushing, grinding, flotation, and dewatering circuits processing 5 300 tonnes per day of new mill feed. The resultant Cu/Ag/Au concentrate is trucked to Prince Rupert for shipment to market. Mill tailing reports to a closed circuit pond from which mill process water is recycled. Details of the concentrator process have been reported( 2,3).Production in the Southern Tail pit, from July 1980 to March 1984, resulted in mill tailing averaging 0.9 g Au/t and slightly more than 20 g Ag/t. Historic data indicate that unrecovered gold is associated with arsenopyrite and silver losses with unliberated tetrahedrite or minor silve,, bearing sulphosalts. Main Zone mill tailing, which commenced production in March 1984, contains approximately 0.5 g Au/t which is probably associated by majority with silver bearing minerals and pyrite while silver losses, 30-40 g Ag/t, are associated with unliberated silver and antimony bearing minerals."

Jan 1, 1985

By Paul Semple

"In 2007, Noront Resources Inc. discovered the high grade nickel copper PGE deposit in northwestern Ontario in a region now known as the Ring of Fire. Since the initial discovery, Noront has advanced the Eagle¹s Nest Project and in September 2012 released a feasibility study for the development of the Eagle¹s Nest Project. This paper summarizes the results of this recent study and outlines additional work planned in the next stages of project development. INTRODUCTIONThe following paper summarizes the findings of the recently completed feasibility study on Noront Resources Ltd.’s Eagle’s Nest Project. The feasibility study was compiled into a NI 43-101 report by Micon International. This paper is intended to summarize the major technical findings and for complete information, interested parties can find the entire NI 43-101 report at www.norontresources.com or on SEDAR.LOCATIONThe McFaulds Lake project area, which includes the Eagle’s Nest deposit, is located at approximately UTM 5844000 N and 547000 E, and between approximately 52º42’ and 52º50’ N latitude and 86º06’ and 86º24’ W longitude, approximately 250 km west of the community of Attawapiskat on James Bay and 575 km northwest of Timmins. The closest all-season accessible community to the McFaulds Lake project area is Nakina, 300 km to the south, where there is a paved airstrip, in addition to all weather road and railroad access (see Figure 1).The First Nations communities of Webequie and Ogoki/Marten Falls are located 90 km west and 120 km south southeast of McFaulds Lake, respectively. Both communities are served by regularly scheduled air service, primarily from Thunder Bay; both Thunder Bay and Timmins serve as support centres for the James Bay communities and the exploration projects in the area."

Jan 1, 2013

By J. S. Stachulak, K. A. Mackinnon

This paper deals with specifying and evaluating fans for mine ventilation projects. Topics such as fan and equipment design life, operating points, and operating conditions are discussed. Common operating problems, such as vibration, parallel operation, mechanical failure, erosion, corrosion, and deficient fan performance are covered. Apart from identifying the potential operating problems, likely causes and suggested remedies are given. Fan type, fan accessories, and likely system effects and fan testing are discussed. Suggestions on what should be covered when evaluating different fan options and proposals and suggestions on the verification of supplier claims and guarantees, including cost of operation, the evaluation of initial capital cost, estimate on maintenance costs, and likely replacement expenditure over the life of the fans. In addition, fan reliability, operational flexibility, suggested construction details and fan vendor past history and experience are reviewed.

Jan 1, 2004

By C. Jay Hodgson, P. J. MacGeehan

"The gold ore zones of the Campbell and Dickenson mines occur within a km-wide, 2 km-long zone of highly altered and anomalously fissile and deformed volcanic and subvolcanic intrusive rocks, cut by a series of mainly post-deformation mafic and quartz-feldspar porphyry felsic dykes.Three main periods of gold ore-forming hydrothermal activity are recognized. In the first, the mine rocks were extensively altered and gold and arsenic enriched; syn-volcanic auriferous veinlet and low-grade chemical sedimentary ores were deposited in what was a major discharge zone of a submarine hydrothermal system. The chemical sedimentary ores are closely associated spatially and temporally with domal rhyolitic extrusions. Because of its mechanical and chemical properties, this synvolcanic alteration zone became the locus of later deformation, and the site of the generation of auriferous hydrothermal solutions, perhaps by pressure solution processes at depth. These solutions deposited, synchronously with deformation and metamorphism, the second and most economically important type of ore zones in the mine: large foliation-parallel and foliation-oblique banded carbonate- 'chert' Rssure-filling veins.In the third and final mineralizing event, high-grade, pipeshaped zones of siliceous replacement-type mineralization, and quartz-arsenopyrite-gold veins, were superimposed on the previous mineralization types after most of the deformation, but before the emplacement of the late dykes. The source of heat and also possibly the fluids for the third mineralizing period may have been the dyke-forming igneous activity. The textures and mineralogy of the banded carbonate- 'chert' veins suggest a near-surface (<3 km) environment of deposition, but their relationship to the fabric of their host rocks indicates they were emplaced in an environment, presumably at considerable depth (5-10 km?), in which the rocks were undergoing intense penetrative deformation. This anomaly is unresolved."

Jan 1, 1982

By Carlos F. Perucca, Maria Virginia Ramírez A.

"Chile based SQM S.A., exploits potassium chloride rich salts at the Salar de Atacama, in northern Chile. The process includes the solar evaporation of natural brines existing in the Salar salt bed, followed by conventional flotation to recover Muriate of Potash (MOP) for fertilizer use.This paper describes a structured method developed to aid in understanding the metallurgical response of the solar evaporated salts to conventional flotation. The method uses classical metallurgical data analysis combined with laboratory and plant-scale testing, and rudimentary mineralogical studies.As a result of the study, several changes were made to the flotation circuit which produced an operation that is much more consistent and easier to control, and has an increased recovery. An optimized circuit, currently being financially evaluated, has also been conceptually designed based on the findings of this work.INTRODUCTIONSQM S.A. is the world’s largest producer and distributor of specialty fertilizers, iodine, lithium, as well as a wide array of industrial and specialty chemicals. SQM is a public corporation whose shares are traded in the Santiago and the New York Stock Exchanges.SQM S.A. exploits the mineral rights at the Salar de Atacama in northern Chile. Its production processes involve the solar evaporation of natural brines existing in the Salar salt bed, aimed at the recovery of Potassium, Lithium and Boron compounds."

Jan 1, 2004

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

By Y. Nakamura, T. H. Okabe, S. A. Sunkar, K. Nose

Ruthenium (Ru) is known as a platinum group element with a very small production volume. In fact, the worldwide annual production of primary Ru metal is only about 20-30 tons, and it depends on the amount of Pt produced, since Ru is a byproduct from Pt smelting. The primary uses of Ru are as a material for resistors, as a catalyst for electrode materials, and as a sputtering target for hard disk memory storage. In order to recover Ru from the spent sand-blasting abrasive media generated during the cleaning of the apparatus used for Ru sputtering, a hydrometallurgical recovery process using hypochlorite solution has been investigated. In this study, various types of recycling processes that are presently under development are also introduced, and their features and differences are discussed. The advantages and disadvantages of the new recycling processes are evaluated, and the possibility of establishing new recycling processes in the future is discussed from a multilateral perspective.

Jan 1, 2014