Search Documents

By David O. DeGagné

While mine backfill plants are becoming increasingly more automated and instrumented, especially with paste fill operations, underground backfill distribution systems have hardly changed over the years. While fill properties are appropriately measured in the preparation plants, as backfill enters the mine borehole, the technology for control, data gathering and reporting is somewhat lacking. Mines typically experience problems with borehole and pipeline plugging, pipeline bursting, bulkhead failure and exposed fill sloughing. With adequate instrumentation of the backfill system it is possible to obtain a complete, continuous and detailed picture of the entire filling operation from preparation to post-pour. Good data will, over time, provide the basis for needed improvements of backfill systems and will be essential to safer, more efficient and less costly fill practices. This paper will review the areas of the filling operations where monitoring would prove critical to eliminate failures such as pipelines, bulkheads, fill exposures, stope walls, etc. The types of monitoring systems currently available will be reviewed and potential areas for development will be highlighted.

May 1, 2001

By Dave Rose, Jacques McMullen

"The Detour Lake mine is located 200 km northeast of Timmins, Ontario, Canada.The mill processes a free milling gold ore using both a gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 tpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The Detour Lake mine has one of the largest gyratory crusher in the world (60"" x 113"") and over the years, many improvements have been made to this crusher with the result of improving plant throughput. This paper will present how choke feeding the gyratory crusher has been found to be one of the main influences on crusher product particle size and plant throughput. It will explain how the effect of choke feeding the gyratory was measured and from that, the various changes made to improve choke feeding of the gyratory crusher.IntroductionOre is hauled from the open pit mine and dumped directly into a single 60"" x 113"" primary gyratory crusher. The live capacity of both the feed and discharge hoppers of the gyratory crusher are designed for two (2) truck loads each, assuming a nominal payload of 300 tonnes per truck. The surge bin under the primary crusher feeds an apron feeder that controls the ore feed rate at approximately 4,200 tph onto a 227 metres long x 1.52 metres wide belt conveyor with a nominal capacity of 4,200 tph.The primary crusher is operated at an open side setting of 172 millimetres to produce a F80 feed to the secondary crushing circuit of 135 millimetres."

Jan 1, 2017

By Mike Sapiro

"Heath Steele Mines is a base metal producer situated near Newcastle, N.B. presently treating 3500 TPD of complex Cu-Pb-Zn ore. The ore consists of massive fine grained sulfides averaging I. 1% Cu, 1.6% Pb and 4.5% Zn.The original mill started in 1956 at 750 TPD and was successively expanded through 1500 to 3000 TPD in 1969. In 1972 an expansion to 4000 TPD was initiated. It was planned to obtain the maximum benefit from equipment and manpower by adding some process equipment, instrumentation, an on stream analyser, and a process control system. The benefits from this approach could be greater than normally expected, because of the complex metallurgy of this ore.IntroductionThe crushing plant is of conventional design with two 5 ½ ft, Symons cone crushers with the crushed ore screened to -7/8 inch on a 61 x 16 1 Al I is Chalmers vibrating screen and stored in four 1000 Ion bins. There are two para I lei grinding circuits, each one consisting of the following: one Rod Mill in open circuit, one Ball Mill in closed circuit with two 20"" Krebs cyclones, and one Ball Mill in closed circuit with three 15"" Krebs cyclones, Al I the Mills are 9' x 121 Al I is Chalmers Mills. The secondary cyclone overflow from each grinding circuit is thickened and combined to form flotation feed. The final product is 65% - 400 Mesh. Two regrind mills have been installed as part of the expansion."

Jan 1, 1977

By Richard Peaker, Jens Lichter, Alexander V. Potapov

"The recent combination of Computational Fluid Dynamics (CFD) and Discrete Element Modeling (DEM) can provide considerable insight into the performance of flotation cells. One area of interest from a fundamental equipment design perspective has been the influence of flotation cell size and the inflow rate on the metallurgical performance of the cell. One of the specific design objectives when increasing the size of flotation cells, or increasing the feed flow to the flotation cell, is to ensure that the feed stream flowing into the cell does not have an opportunity to bypass the mechanism.This paper describes the initial modeling efforts to quantify the inter-relationship of cell size, inflow rates, and feed and discharge box placement, on the retention time distribution of solids in the flotation cell, and the fraction of particles that bypass the mechanism on a size by size basis.INTRODUCTIONThe great majority of newly installed cells in mineral processing plants world-wide are of the cylindrical tank design and this tank shape offers a number of hydraulic advantages over the older style of square cells. Cylindrical cells give symmetrical flow patterns and by careful design of the mechanism and tank internals, the flow patterns generated can concentrate the more intense mixing in the lower portion of the cell to promote good solids suspension and particlebubble contact. Simultaneously, cylindrical tank design gives a more quiescent upper zone for particle-bubble transport into the froth zone. These symmetrical flow patterns are naturally disturbed in normal operation by the slurry inflow and outflow from the individual cells. The challenge for flotation cell designers is to determine the magnitude of these flow disturbances, and to assess whether or when the inflow and outflow rates have a sufficient impact on the hydraulic flow patterns so as to potentially affect the metallurgical performance of the flotation cell."

Jan 1, 2007

By E. Marcoux, F. Lotfi, A. Belkabir, L. Maacha, A. C. Brown, S. Brunet

"Koudiat Aïcha is a small Zn-Pb-Cu deposit, enclosed in the Visean Sarhlef volcano-sedimentary series of the Moroccan Hercynian Jebilet massif. Base metal mineralization is located between a basal unit consisting of black argillite with arenite intercalations, and an upper unit composed of black argillite with locally fossiliferous calcareous units towards the top. Paraconcordant gabbro sills are present in both the upper and basal units, and the enclosing strata. Three successive phases of deformation linked to regional deformation overprint the volcano-sedimentary rocks and gabbros, as well as the sulfide mineralization.The mineral deposit includes several lenses of massive to semimassive pyrrhotite, 1 to 20 m thick, with a large halo of disseminated sulfide veinlets and sulfide nodules within a zone of intense chlorite alteration in the footwall. The ore mineralogy consists of massive to semimassive pyrrhotite with lesser amounts of sphalerite, chalcopyrite, arsenopyrite, galena, pyrite, and stannite.Lead isotope results (206Pb/204Pb averaging 18.27) suggest that the metals of the Koudiat Aïcha deposit are derived from the volcano-sedimentary host rocks. Sulfur isotopes also indicate a volcano-sedimentary origin, with bacterial reduction of sulfate (d34SCDT = -7.5‰ to -10.5‰). The conditions for sulfide meta-morphic equilibration range from 250° to 330°C (sphalerite and chlorite geothermometers). The gabbroic sills could have been a local heat source for hydrothermal circulation. Based on these geological and mineralogical features, a Besshi-type model seems appropriate for the genesis of the Koudiat Aïcha mineralization.Koudiat Aïcha est un petit dépôt de Zn-Pb-Cu, encaissé dans la série volcano-sédimentaire Viséenne de Sarhlef dans le massif Hercynien de Jebilet au Maroc. La minéralisation en métaux usuels se situe entre une unité basale d’argilite noire interlitée d’arénite et une unité supérieure composée d’argilite noire comprenant localement des calcaires fossilifères près de son sommet. Des sills de gabbro paraconcordants sont présent à la fois dans les unités basale et supérieure, ainsi que dans les strates environnantes. Trois phases de déformation successives associées a la déformation régionale superposent leurs effets sur les roches volcano-sédimentaires, les gabbros, ainsi que la minéralisation sulfurée. Ce gîte comprend plusieurs lentilles de pyrrhotite massive a semimassive de 1 a 20 m d’épaisseur au sein d’un large halo de veinules de sulfures disséminés et en nodules au sein d’une zone intensément chloritisée dans le mur du gisement. Le minerai consiste en pyrrhotite massive à semimassive avec des quantités subordonnées de sphalérite, de chalcopyrite, d’arsénopyrite, de galène, de pyrite, et de stannite. Les résultats de l’analyse des isotopes du plomb (206Pb/204Pb moyen de 18.27) suggèrent que les métaux du gîte Koudiat Aïcha proviennent des roches volcano-sédimentaires encaissantes. Les isotopes du souf¬fre indiquent eux-aussi une origine volcano-sédimentaire, impliquant la réduction bactérienne des sulfates (d34SCDT = -7.5‰ et -10.5‰). L’équilibration métamorphique des sulfures s’est produite entre 250° et 330°C (géothermomètres à sphalérite et chlorite). Les sills de gabbro pourraient avoir été la source de chaleur locale responsable de la circulation hydrothermale. Sur la base de ces caractéristiques géologiques et minéralogiques, il semble approprié d’invoquer un modèle de type pour Besshi pour expliquer la genèse de la minéralisation de Koudiat Aïcha."

Jan 1, 2008

By C. Siac

"It is a widely held view that in the 21st century, the mining industry will be dominated by a relatively small number of large companies, truly global in scope and internationally staffed (Gooding, 1997). Interestingly enough, most of the exploration and exploitation activities are being carried out by junior and major mining companies from common law jurisdictions in civil law countries, in particular in Latin America, where in recent years, the region has ranked first as a destination for exploration dollars, thanks to the reforms undertaken by some countries to amend their legal framework to attract foreign investment. From a lawyer’s point of view, this is where the main challenge lies: how to bridge the gap between the two legal systems.In order to avoid pitfalls, common law lawyers should be more diligent and proactive when dealing with civil law jurisdictions, given the different systems of law, standards, traditions and customs. Common law lawyers cannot be expected to be well-versed in civil law but they should not be completely unfamiliar with it either. A balance should be struck to ensure clients’ needs are professionally taken care of and that common law requirements and standards are met."

Jan 1, 2003

By Fidelis T. Suorineni

Rapid drifting enables quicker access to orebodies, higher production rates and a resultant reduction in production cost. The Mining Innovation, Rehabilitation and Applied Research Corporation (MIRARCO) funded by the Canadian Mining Industry Research Organization (CAMIRO) has developed a methodology for safe rapid drift development within the underground metalliferrous mining industry in Canada According to industry survey, about 36% of drift development cycle time is spent on support installation. MIRARCO has developed a methodology for safe rapid drift development based on minimizing time spent on support installation. The methodology includes a critical review of the rockmass classification systems, examination of current support practices in the mining industry and civil tunneling, review of rapid drift development practice in South Africa, introduction of risk hazard procedures to account for material property variability and the development of a WIZARD as a quick decision-making tool for the implementation of the procedures. A comprehensive field data collection procedure was put in place and data collected from various mines to verify and calibrate the support selection rationale. The findings of the research programme resulted in the development of an improved rockmass classification system and showed that construction effects have drastic influence on support levels but is often not accounted for in assessing support levels. Stress effects and structurally controlled failures are the other important factors to take into account in rapid drift development. Three support classes were established for safe rapid drift development as No Systematic Support, Light Support and Strong Support. The support levels took into account cost, rate of installation and safety based on compatibility with ground characteristics. This paper describes the methodology for safe rapid drifting within the underground metalliferrous mining industry in Canada and highlights the key issues and major drivers behind their continued development at the Geomechanics Research Centre within MIRARCO.

May 1, 2004

By Dominic Fragomeni

"The mineral processing industry has had a long history of innovation that is recognized but not often celebrated. These include significant advances in mineral measurement, testing, comminution, mineral separation and process control technologies that have transformed mineral assemblages into ore.This presentation presents some of the major mineral processing innovations and the impact they have had on our industry. As we look to the future, it is critical that we innovate and change. We will explore some examples of the next developments and how they can be catalyzed in the face of risk management, lower metal price cycles, resource constraints, inertia and the challenge of short term value delivery."

Jan 1, 2017

"Polycom, a new approach to ore processing based on pressure comminution, is obviously a very attractive alternative to conventional processing methods.Since a full-scale pilot plant was commissioned in 1986, more than 125 commercial installations, with capacities up to 1000 t/hr, have gone ahead.Already successfully used in processing cement clinker, limestone, coal, and other minerals, Polycom high pressure grinding results in:o Significantly reduced capital costs, because smaller units can be used m new installations;o Capacity increases of up to 100% in existing facilities; and o Operating economies that include energy savings of 20% or more, and reduced wear parts consumption.1. IntroductionAutogenous or semi-autogenous mills in conjunction with rod or ball mills are used with preference for ore processing. Most ball mills are of closed-circuit design and operate with mechanical classifiers (spiral or rake classifiers) or hydrocyclones. In other words, the ores undergo wet primary grinding, since slurries are required for the downstream separation stages anyway. This paper presents a new grinding system based on high pressure comminution of ores. This grinding process allows:- Energy savings of up to 20 % or more- Capacity increases of up to 100 % and more- Reduction of wear costs- Smaller units for new installation and thus- Reduced investment costsThese advantages are highly interesting for both new installations and conversion projects, particulary in cases where an increasing hardeness of the ore, i.e. rising Bond Work Index, reduces the output of the plants or where the metal assay of the ore decreases and the capacity of the existing systems has to be increased. POLYCOM high-pressure grinding rolls have established themselves with great success already for grinding cement clinker, granulated blast furnace slag, limestone, cement raw materials, coal and other materials.Meanwhile more than 250 high pressure grinding rolls have been installed worldwide. Capacities up to 1.000 t/h with roller diameter up to 2.8 m and drive units up to 2.400 kW are installed."

Jan 1, 1991

By P. K. Frempong, S. D. Butt

"A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine.The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semivariogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates."

Jan 1, 2004

A case study for the application of a novel geostatistical technique for resource estimation of a narrow steeply dipping, gold-silver mineralized quartz vein deposit is presented. The technique is novel in two respects. First, mineral grades are kriged directly rather via the accumulation method more often applied to vein deposits and, second, a modified 2D ordinary kriging algorithm is used that allows the calculation of a single grade and variance for irregular shaped blocks of varying sizes. The objective of this investigation was to evaluate the suitability of this novel geostatistical technique for resource estimation of the Poura mine deposit and, if appropriate, to lay a firm foundation for future geostatistical work at the mine. The reserve estimation concentrated on the remnant ore blocks and pillars in both underground and surface workings. The data, which was collected in 2D coordinates with grade and vein thickness values, was first analyzed statistically and used to compute experimental semi-variograms. Appropriate semi- variogram models were fitted and various aspects of the estimation technique were evaluated using cross-validation error analysis, with acceptable results. A block kriging computer program called Krige2D was developed to implement the modified 2D kriging algorithm and calculations. Production data were not available to evaluate the computed block resources, but they were compared with a previous resource data determined using an arithmetic approach. The geostatistical technique estimated slightly higher grades but lower overall tonnages as compared to the earlier arithmetic estimates.

Feb 1, 2004

By Marc D. Melker, Geoffrey R. Lane, Michael Jahraus

"The Cresson gold deposit is located in the Cripple Creek district of Colorado. The deposit is composed of volcanic intrusive rocks and volcanogenic sediments where gold mineralization is associated with veins and cavities within a diatremal breccia.The purpose of the current study was to:1. Determine the penetration potential of the Cripple Creek Breccia.2. Assess the relationship between penetration and gold recovery within the Breccia.Two methods were applied using a cyanide solution containing ultraviolet sensitive dye to elucidate pathways of penetration within the rock. The first involved stagnant soaking of twoinch square pieces within the solution. The second method involved column leaching of ~100kg of Breccia crushed to P80 12.7 mm (0.5 inch). Samples were selected at specified intervals to capture the penetration progress of the solution. Photomicrographs and image analysis were utilized to illustrate and quantify the degree of penetration.Results indicated that the maximum penetration for the Cripple Creek Breccia (85 to 97%) due to a porous and permeable groundmass, containing large non-porous lapilli fragments. In addition, ~90% of leachable gold was recovered with only ~50% rock penetration.INTRODUCTIONDye penetration studies were first developed at SGS-Lakefield Research for the purpose of determining the fluid penetration amenability of differing rock types. The method was to place a large rock or drill core in a pan with 1 to 2 inches of a pre-mixed, water based fluorescent dye. The sample was sequentially cut after prescribed time periods to reveal a fresh surface. The cut surface was photographed under long wave ultraviolet light, and the same piece returned to the dye and allowed to sit until the next prescribed cutting."

Jan 1, 2006

By R. Tessier, C. R. Larsen

"INTRODUCTIONOn November 10, 1982 Nor and a Inc signed an agreement with Golden Sceptre Resource Ltd. and Goliath Gold Mines Ltd. to construct a mine and milling facility.The Golden Giant mine is located in the Marathon area of north - western Ontario, immediately north of Highway 17 and about- 3.5 km west of Highway 614.With the exception of selected unit processes, the mill was designed for a nominal throughput of 2500 tonnes per day with early operating data to be used to identify sections requiring possible expansion to achieve an ultimate throughput of 3000 tonnes per day.Commissioning of the highly instrumented milling complex which includes crushing, grinding, cyanidation, and carbon in pulp processes commenced in February 1985. After water testing various sub-circuits from grinding through tailings, waste ore was introduced to ensure proper mechanical and electrical operation of process equipment.The first ore was milled as a mixture with waste on March 4, 1985. The first gold bullion was poured April 6, 1985.Initially, ore was only available from mine development at a rate of 700 t/d, which was milled at a minimum rate of 1200 t/d. While regular weekly shut downs of two to three days was useful for mechanical maintenance, changes, and modifications, process tuning was more difficult due to the non-steady operation. As increased quantities of ore became available, regular weekly shutdowns tapered off and process operation improved accordingly. For testing purposes and as ore was available, mill throughput was increased regularly to 2300 t/d and for very short periods of time to nearly 3000 t/d.No major design or operating problem has been encountered to date. The following is a brief description of the milling process and various operating highlights. Process flowsheets are shown in Figures 1 through 6."

Jan 1, 1986

By Johnny Zhang, Yang Anguo, Li Weifeng, Xueyi Guo

"SKSTM oxygen bottom blowing smelting technology was developed by SKS-ENFI at SKS Smelter, Hunan in the 1990s to replace the conventional sintering process and thus to meet the high national EHS standard for lead.Since then, two major milestones have been achieved:1. Since 2002, the SKS oxygen bottom blowing smelting-blast furnace reduction has been in operation at SKS, YGL, Chizhou smelter etc. Now in China, about 50% of the lead (4.2 millions t/year) is produced using SKS process; and2. Since 2008, the blast furnace has been replaced by direct reduction of molten rich lead slag at YGJ smelter, which is more energy-efficient since no slag cooling is required. This two stage process (SKS Oxidation- Direct Reduction) is named as the YGL process.Since 2008, numerous technological innovations have been implemented in the furnace design, process control, and maintenance at YGL. The plant has been successfully demonstrated its unique excellent performances on all aspects from processing capacity, product quality, energy reduction, cost reduction and emission reduction. The purpose of this report is to update all the improvements with proven tracks.Meanwhile, a preliminary comparison on the following aspects between the YGL process and other similar technologies has been discussed:1. Plant design and operating conditions;2. Mass and heat balances, metal (Pb, Ag) recovery;3. Consumables, oxygen gun and refractory lining life;4. Energy consumption and operating costs;5. Sulfur capture and emission reduction etc.It is concluded that the modified SKSTM process is a clean SO2-free emission process. The process is characteristic of other features such as no extra fuel addition, low capital with a small foot-print design, low OPEX, high throughput, easy operation, long refractory lining life and high productivity (95%+ on line time annually). It offers an alternative cost-effective technology for lead smelting industry."

Jan 1, 2014

By R. Amelunxen

"The molybdenite associated with copper porphyry ores is generally treated in a flotation circuit consisting of a separation and a cleaning section. In the last few years column flotation cells have replaced the numerous counter-current stages that were previously used in the cleaning section. Despite this, little has been published regarding the number of column cleaning stages required. Therefore a Moly flotation database is assembled with the objective of verifying the existence of a common upgrading profile. This can then be used as a guide in the prediction of the number of stages required to achieve a given concentrate grade.INTRODUCTIONAlthough the first use of Column Flotation was on copper flotation products, the popularity and understanding of their operation was not really achieved until they were widely implemented in Moly circuits in early 1983. The use of columns in Moly plants has since left a legacy of information, both published and unpublished. The data collected since that time has been used primarily used to establish column operating parameters and to determine upgrading potential within the circuit.Byproduct Moly generally occurs with porphyritic copper ores in concentrations less than 0.1% MoS2. As such, piloting a new moly ore to produce, say 5 Kg/Hr MoS2, in a slurry approximately 1 Lt/min (at 10% solids), requires a moly plant feed of about 570 Kg/Hr, which translates to a mill feed rate of 200 to 800 Tonnes per day (depending whether you deal with Chilean or Canadian ores). Piloting Moly for any lower tonnage would reduce the accuracy of the testwork.Thus a need exists to collect operating data in order to establish the existence of process relationships that could be used for feasibility and design purposes.The object of this paper is to expose a preliminary relationship that could be used for the purposes described above and to apply the findings to a preliminary design of a moly cleaning circuit flowsheet."

Jan 1, 1990

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation's Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system's 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By Lynn M. Gould

Syncrude Canada operates the largest oil sands crude oil production facility in the world and produces over 13 percent of Canada?s total oil requirements. To do this, Syncrude mines the oil sand in open pits, extracts the raw oil known as bitumen from the sand using water-based processes and upgrades it into sweet light crude oil by fluid coking, hydroprocessing, hydrotreating and reblending. The final product, Syncrude Sweet Blend (SSB) is sent by pipeline to three Edmonton area refineries and then to pipeline terminals which ship the SSB to refineries in Canada and the United States. As parts of the Mildred Lake Base Mine reached their economic life, they were replaced with new facilities at the Aurora satellite mine. Aurora is situated on Oilsand Leases 10, 12, and 34, 35 kilometres northeast of the Mildred Lake facility. (Figure 1) In 2000 the first hydrotransport low energy extraction production train started up at Aurora. A second production train is scheduled for start up in 2003. Open pit mining at Aurora occurs using two hydraulic shovels, two cable shovels, and trucks ranging from 320 ton to 380 ton payload capacities.

May 1, 2002

By J. Don Scott

Analytical predictions of the rate and magnitude of settlement of deposited oil sands tailings slurries generally overestimate how fast pore pressures will dissipate. Field deposits of nonsegregating tailings to mature fine tailings show continued high pore pressures near the surface which impede surface reclamation. In geotechnical analyses which predict the consolidation behavior of soft soils a finite strain theory is used. Effective stress-void ratio and void ratio-hydraulic conductivity relationships determined from laboratory large strain consolidation tests, are used in the finite strain predictions. This theory, however, cannot predict the full range of sedimentation, consolidation and pore pressure dissipation which occurs in large scale deposits of thixotropic tailings slurries. A new large strain consolidation model which assumes that the creep rate of the slurry exceeds the pore pressure dissipation rate is being investigated. This model is relevant for rapidly deposited, low permeability thixotropic slurries where the upwards drainage path increases by several meters a year, such as, in oil sand fine tailings ponds and nonsegregating tailings deposits. The model will be verified by analyzing the 10m high column of fine tailings at the University of Alberta which has been monitored for over 20 years and in which the excess pore pressures are still very high.

May 1, 2004

By James Anstey

BHP Billiton?s Cannington facility is a mining and minerals processing plant near Mt. Isa in Central Queensland, Australia, producing silver, lead and zinc. Mine ore is processed in a concentrator, which consists of grinding, flotation, thickening and filtration. Grinding is carried out in a fully autogenous (AG) mill. The mill operates in closed circuit with a pebble crusher. Throughput is approximately 380 tph. Cyclone overflow from the grinding circuit is fed into a flotation circuit for the recovery of lead, zinc and silver. Two concentrates are produced (lead and zinc), which are then thickened and filtered. The filtered concentrate is transported by road to a rail receiving station. From here the concentrate is railed to port in Townsville for shipment to the smelter. Matrikon and Engineers at BHP Billiton?s Cannington Mine have used ProcessACT to develop a flexible, nonlinear dynamic simulator for the grinding circuit to further enhance process understanding, as well to investigate various optimization strategies. An online charge volume estimator was also developed for the AG mill to aid in the understanding of overload conditions, which for the previous two months had been the primary contributor to downtime. The models were developed using a combination of first-principles modeling along with input-output dynamic responses. Examples of models used include: Morrell ?C? model for power and charge shoulder/toe angle prediction; Whiten?s mixing model for breakage and hold-up; Nageswararao cyclone model for predicting cut size; slurry recovery and water recovery. The composite model simulates system dynamics starting from the stockpile reclaim system and finishing at the feed for the flotation process. The objective was to provide a tool that assisted Cannington in understanding their Grinding Circuit and allowed them to develop and evaluate circuit optimization strategies. BHP Billiton Cannington Mine is now considering development of a Grinding Circuit Optimizer utilizing the models developed for the simulator.

Apr 1, 2005

By Stephen R. Grano, Jon Glatthaar, Philippe Steinier, Christopher J. Greet

"The importance of the oxygen content of sulphide mineral pulps in determining which reactions occur, and their subsequent influence on flotation behaviour is grossly underestimated in most operating concentrators. While pH is routinely monitored, Eh and dissolved oxygen measurements are obtained infrequently. However, dissolved oxygen measurements in conjunction with other pulp chemical parameters (i.e. pH, Eh, and EDTA extractable metal ion analysis), can provide valuable insight into where and what type of reactions are occurring within a circuit. Unfortunately, these readings yield “instantaneous” measurements of the pulp chemical parameters.What is needed is a means of establishing how reactive a pulp is, and how this reactivity changes as components of the system are manipulated. Oxygen demand provides an opportunity to do this. Several attempts at measuring the oxygen demand of a pulp have been made in the past with varying degrees of success. Most notable among these are Noranda and BOC Gases.Learning from these experiences, Magotteaux have developed the MagO2 ® demand vessel to measure the oxygen demand of mineral pulps. This paper described the apparatus, and through a case study on Broken Hill lead/zinc ore demonstrates how the MagO2 ® demand vessel is used.INTRODUCTIONThe role of oxygen in flotation is complex. While a considerable body of work exists demonstrating the strong involvement of oxygen in the interactions between sulphide minerals and collector (Gaudin and Finkelstein, 1965; Gaudin, 1974; Woods, 1984; Laajalehto, Nowak and Suoninen, 1993), the presence of oxygen can also affect the oxidation state of sulphide and non-sulphide minerals, which can impact on their flotation behaviour. Further, sulphide mineral oxidation is related to their oxygen demand (Spira and Rosenblum, 1994)."

Jan 1, 2004