Search Documents

By J. Peterson, D. D. Tannant, J. Todd

"A review of blast designs and improved blasting practices at the EkatiTM diamond mine is presented along with the results of three blast-monitoring experiments. Blast monitoring was undertaken to investigate blast damage mechanisms in the mine’s well jointed rock mass. Rock mass damage caused by production, pre-shear and wall control blasts was measured. EkatiTM uses 270 mm holes for production blasting, and 165 mm holes loaded with a decoupled charge for pre-shearing. The production blasts are loaded with bulk emulsion/ANFO blends. The mine plan involves using 30 m double benches. A 30 m high pre-shear is drilled and blasted prior to the production blasting that is done with sequential 15 m benches. This paper summarizes the monitoring equipment and data gathered to date. IntroductionThe EkatiTM diamond mine is located about 300 km northeast of Yellowknife, Northwest Territories, Canada. The mine is a joint venture of BHP Diamonds Inc. (80%) and geologists Charles Fipke and Stewart Blusson (10% each). The EkatiTM mine is Canada’s first diamond mine and BHP is the operator. The mine is accessed by air and by a winter ice road.The first kimberlite pipe mined at EkatiTM is known as the Panda pipe. The Panda open pit mine will have a total depth of 315 m (Fig. 1), a width of about 600 m, and a 50° overall slope. Initial ore production is 9000 tonnes per day.This paper summarizes the pre-strip blasting and the evolution of the production and wall control blast designs from 1997 to 2000. The initial blast designs and the rationale behind subsequent changes that took place are presented along with the techniques currently in use.The paper also briefly presents an experiment done to measure the rock mass response to blasting. Three blasts were instrumented with geophones, gas pressure sensors and time domain reflectometry cables. A brief summary of the instrumentation and data gathered is included."

Jan 1, 2001

By M. Ataka

Magnesium alloys are not easy to plastically deform at room temperature and may suffer from edge cracking at high reductions, especially during sheet rolling. In this study, the authors attempted to improve the rollability by the low-temperature hot rolling method, in which the rolling temperature range is lower than that of hot rolling, and also by the edge-heating method, which locally heats sheet edges.

Jan 1, 2006

By Rakesh Kumar, Rajabrahma K., A. K. Verma, V. Mukesh

"In this study, laboratory investigation as well as numerical investigation is carried out to ascertain the transition from one mode to another for Semi-circular bend setup. Laboratory investigation is carried by varying the span length (s/2R); crack length (a/R); notch angle (a); and notch thickness (t). The specimen consists of cement, sand and water mixture in a ratio of 1:1:0.5 by weight and are prepared as per the ISRM standards (2014). Tests are conducted by a servo controlled universal testing machine at a strain rate of 0.2 mm/ min. The results are collected in terms of failure load, crack mouth opening displacement (CMOD) and images of crack initiation and propagation.Image analysis of laboratory tested samples shows that crack initiates at the notch tip when the notch inclination angle is 0°. As the notch angle increases (i.e. 30° and 60°) the fracture begins to initiate behind the notch tip. The direction of crack propagation in front and back side of the sample is same for notch inclination angle is 0° whereas it differs more and more as crack inclination increases. The transition represents the change in mode of failure from mode I (0°), mode II (30°) and mixed mode I/II fracture (60°).Finite element method used to find the transition based on MTS failure criterion. The inclination of notch is varied like 40, 42, 44, 45, and 50 deg and FEM analysis shows that the transition from mode-I to Mode-II take place at 49 deg. The same procedure can be extended to find the transition from mode-II to mode-III."

Jan 1, 2015

By C. S. Maggs, L. Shwydiuk, H. W. Newcomen

The southwest wall of the Lornex Pit at the Highland Valley Copper mine has been experiencing slope displacements since 1978. Measures to manage the displacements on previous pushbacks have included stepping out, scheduling pushbacks to unload the crest of unstable areas, slope dewatering and mining with intensive slope monitoring. The final pushback on this wall is currently being mined and substantial modifications to the slope geometry could prove to be uneconomical. As a result, a campaign of surface water collection and diversion, horizontal drainhole drilling and deep well drilling is currently underway to maintain an acceptable degree of stability to the end of mine life. The various factors contributing to instability, including engineering geologic controls, rock mass strength, and surface and groundwater hydrology are presented. Movement trends, displacement magnitudes and stability analyses results are also discussed.

Jan 1, 2003

By Penny C. Stewart

Narrow vein underground stope design engineers in Australia have expressed significant interest in the requirements and methodology for developing site-specific stability charts. This is largely due to a concern that existing stope stability charts inadequately take into account factors influencing narrow vein stope stability, such as the effect of backfill abutments and the effect of in stope pillars. This paper presents conclusions from a comprehensive statistical examination of case history requirements for a site specific stability chart and critiques literature arguments for site-specific charts. A new statistical analysis technique and a large comprehensive stability database enabled the authors to quantify case history requirements and any site-specific effects the model exhibits. The analyses indicated that a reliable stable-failure boundary requires at least 150 case histories, of which a minimum of 10 percent should be unstable stope surfaces. Marginal site-specific effects were observed for the operating conditions captured within the database. The authors conclude that the apparent site-specific effects noted in previous literature are attributable to operating conditions inadequately represented in the database. Such operating conditions could induce erroneous stability predictions at any site, and are therefore not truly site-specific. Following from these conclusions, a strategy for taking into account operating conditions particularly relevant to narrow vein mining has been proposed. In particular, the development of a chart that accounts for the effect of backfill abutments on stope stability. Backfill abutment effects are particularly relevant to mechanised narrow vein mining methods such as modified Avoca. Collaboration from at least five sites is required to obtain access to relevant data and underground drives for geotechnical mapping. Preliminary estimations indicate that approximately three months fieldwork is required to meet case history requirements. CMS data in conjunction with 3-dimensional design software will be used to calculate equivalent linear overbreak/slough (ELOS). In contrast to stable, failure, major failure and caving categorical variables, ELOS is an objective and continuous stability variable and is therefore, more conducive to mathematical modelling.

Oct 1, 2001

By L. D. Smith

"This paper examines the impact of the various assumptions that go into an economic evaluation, and shows how these can be combined to show an exciting result that may not really exist. An example of an embellished case (the kind that one frequently sees when projects are being promoted) is developed and the cumulative impact is analyzed to show the actual project underneath. The paper also points out some areas to watch for overly optimistic assumptions such as prices, inflation, and debt. The concept of a “bare bones” base case is proposed (constant metal prices, constant dollars, no inflation, no debt, no interest, on a project basis, after tax) as a common reference point.As well, the discount rate is examined as one of the fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk."

Jan 1, 2002

By C. A. Sutherland

"Smelting of copper-gold ore from nearby Rossland mines started at Trail in the 1890s. As ore from the Rossland mines became exhausted, lead smelting of hand-sorted galena ore from other British Columbia mines was initiated. With the development of flotation technology for the separation of lead, zinc, and iron sulphides in the first two decades of this century, the large Sullivan orebody at Kimberley, British Columbia, became the f oundation for the growth of a major zinc and lead smelter at Trail. Lead smelting began in 1901, electrolytic zinc in 1916, and by 1984, the Trail metallurgical complex had produced 10 million tons of each metal. Its present capacity is 270000 tonnes per year of zinc and 110 000 tonnes/year of lead.This paper reviews the history of technological changes in the Trail production plants, emphasizing the zinc plant modernization program started in the 1970s, and also the planned introduction of the QSL oxygen lead smelting process in the late 1980s. Lead modernization will increase production capacity to a maximum of 160000 tonnes per year.IntroductionCopper-gold ore was discovered at Rossland, British Columbia, in the year 1890, starting a mining industry that was to last over three decade s. Selected ore was at first transported at high cost to distant U.S. smelters, so there naturally followed a decision to construct a small copper smelter to process the local ore to matte. It was built in 1896 at the mouth of Trail Creek on the Columbia River, about 10 km from Rossland. This little smelter was to develop and diversify in the next 90 years into the world 's largest lead-zinc producer).The mining boom that occurred in the northwestern United States and southeastern British Columbia in the period of 1890 to 1910 saw the brief operation of many small local smelters. The only one to survive was the smelter at Trail. The circumstances that permitted its continued life and subsequent growth, form a fascinating history of business deals, litigation, andsteady technical progress.Early investment in local railway transportation and options by F.A. Heinze, the smelter' s founder, attracted the attention of the Canadian Pacific Railway Company, which purchased Heinze' s assets in 1898. This provided the capital base for survival and growth of the smelter, which remained and prospered under the Canadian Pacific umbrella for almost ninety years. It was registered as the Consolidated Mining and Smelting Company of Canada Limited in 1906; in 1966, this name wasshortened to Cominco Ltd.The Rossland mines continued to supply copper ore for the smelter until the late 1920s, but lead-silver ore also became available from the contemporary mining boom in the Slocan area, about 80 km away. In 1901, the Trail smelter diversified into lead; and when the CM&S Co. acquired the St. Eugene Mine at Moyie and the Sullivan Mine at Kimberley, the smelter was guaranteed a firm supply of lead ore. The company also purchased the West Kootenay Power and Light Company, which even before the turn of the century had constructed the first of four hydroelectric generating plants on the Kootenay River near Trail. This acquisition assured the CM&S smelter and its local mines of a stable power supply and the opportunity to diversify into power intensive technology."

Jan 1, 1988

By I. Filippova, L. Filippov

"The by-product potential of light rare-earth elements (LREE, La, Ce, Nd) and rare-metals (W, Nb, Sn) within the St Austell kaolin deposits (UK) is related to the kaolinisation process, which liberates the accessory heavy minerals of the host granite in the clay matrix and allows their separation in the waste streams. As a consequence these minerals are pre-concentrated in the micaceous residue which displays relatively high LREE content (around 170 ppm) hosted by monazite which is mainly distributed (up to 95%) in the -100 µm fraction. A combined gravity/flotation concentration flowsheet, starting with classification of the residue into 3 size fractions (+150 µm, 150-53 µm and -53µm) was developed. This study presents the results of the clay-rich -53 µm size fraction beneficiation by flotation using sodium oleate and hydroxamate as collectors.The effect of dispersant addition during de-sliming operations on flotation efficiency was also investigated. The LREE grade in the floated product obtained with sodium oleate increased from 3370 ppm to 5350 ppm and recovery from 30% to 80% with dispersant which is attributed to clay coating. Comparison of flotation performance and Falcon Ultra-Fine (UF) concentration of monazite to previous results obtained with Falcon Semi-Batch (SB) gravity concentrator on the unscreened raw residue clearly shows that flotation of the fine residue is more efficient than Falcon UF and Falcon SB. Indeed Falcon UF produced high recoveries (87-95%) but with almost no enrichment (1.3-1.4 ratios) whereas Falcon SB concentration of unscreened residue produced higher grades (up to 0.6 % LREE) but with low recoveries (17-22 %). These preliminary results show that LREE can be pre-concentrated suggesting that the micaceous residue stream (and the associated tailings dams) could be considered as a potential resource for these metals."

Jan 1, 2016

By Mark Sherman, M. Dennis, Raj Rajamani

"The two Alumbrera 36ft (10.97m)dia. SAG mills were sized, using the FDW ""Grindpower 'I program, to treat an average of 1852 tph each. This paper describes how modelling of the shell lifter design, using the Millsoft program, identified milling inefficiencies caused by poor charge motion. This explained the ""as built"" circuit's inability to achieve the throughput rates predcted by the circuit's designer. Use of the Millsoft program to design a new, dramatically different lifter configuration, in conjunction with a different approach to variable speed drive utilization, has resulted in an improved charge motion and a 30% increase in hard ore milling rates. The new lifter design has allowed the designer's predicted average throughput rates to be achieved.IntroductionThe Alumbrera project grinding circuit consists of two 36ft dia. X 17ft EGL, 13 500 kW, variable speed, gearless drive SAG mills coupled to four 20ft dia. X 30ft EGL, 6 000 kW fixed speed, gear driven, ball mills. The circuit is configured as two identical grinding aisles, each consisting of one SAG mill and two ball mills. No pebble crushing circuit was installed due to the expected absence of a critical size fraction in the first years of production. However, the grinding circuit layout does incorporate space for a pebble crushing retrofit. At present, only about 5% - 10% of the new mill feed reports as trommel oversize and is recycled back to each SAG mill using a water cannon.The circuit was designed to be ball mill limited and to treat the four major Alumbrera ore types at rates varying between 68 000 tpd, and 89 750 tpd, depending on ore hardness. Average throughput rate, and hence nominal design rate, for the grinding circuit was 80 000 tpd (1 852tph per line at 90% availability)."

Jan 1, 1999

By X. Cao, H. Huang, Z. Dai

"Crystal phase of copper-containing slag regulation by the slag viscosity, cooling speed and cooling method, where the slag viscosity is related to the temperature and alkalinity. According to the mineralogy properties of a copper-containing slag, experiments of crystal phase regulation and flotation were conducted. When the copper-containing slag that adding a small amount of calcium oxide was cooled slowly at a rate of 3°C/min and about 1050°C n a cinder inclusion system, the viscosity of slag can be remained under 0.25 Pa·S and more than ??% of copper particles that the grain size is larger than 20 ?m in slag. The whole flow of flotation experiment was carried out to recover copper from the copper-containing slag with crystal phase regulating and the copper concentrate grade was ?????%, the recovery efficiency of copper was 94.18%.INTRODUCTIONChina's annual output of copper slag is more than 6 million tons, the current total has reached 80 million tons. It is equivalent to 640 thousand tons of copper metal with the copper grade of 0.82%. Most of the smelting slag were storage. It is not only occupy the land and pollute the environment, but also make a huge waste of resource (Alp, Deveci, & Süngün, 2008; Carranza, Iglesias, Mazuelos, Romero, & Forcat, 2009; Gorai, & Jana, 2003), therefore, it is good way to achieve copper slag resources by the effective recovery of valuable component from copper smelting slag, which is an important measure of the current process of copper smelting slag and implement the central authorities to vigorously develop the circular economy, improve the recycling of resources, increase copper production of intensive development (Zhou, et al., 1994; Zhang, Zhang, & Wang, 2005). Currently, researches on comprehensive utilization of the coppercontaining slag made a much progress (Wei, 2004; Liu, Gai, Yang, Sui, Li, & Fu, 2008; Liu & Zhu, 2008; Zhang, 2010; Sun, Chen, & Tang, 2012; Qin, Wang, Ren, Wei, Peng, & Gu, 2012). Flotation is one of the most effective method to recover the copper from smelting slag, which has the features of low cost and high efficiency (Song & Liu, 2001; Zhang, Wang, & Li, 2012). But the copper particles in the copper smelting slag distribution is very uneven, and the thickness of the material is very serious. The copper content in the micro level is higher, the size of copper sulfide ore is less than 0.043 mm, which leads to the difficulty of the monomer dissociation (Tossavainen, Engstrom, Yang, Menad, Lidstrom, Larsson, & Bjorkman, 2007; Moustakas, Mavropoulos, Katsou, Haralambous, & Loizidou, 2012). In this study, according the process mineralogy of a smelting copper slag, the crystal of smelting copper slag was optimized by controlling the temperature, alkalinity, cooling rate and cooling method, which makes the fine copper mineral particles in the copper slag crystal further, and can be used to meet the particle size requirements of flotation, thereby enhancing the flotation of copper."

Jan 1, 2016

By M. Drozd, M. Somppi, Z. F. Yamak

"Activated carbon is used to recover gold in solution from various gold circuit designs including carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes; however, the characteristics and durability of the activated carbon can vary. Handling this medium poses challenges when fine carbon losses occur in the CIP, CIC, and CIL circuit discharge. Additionally, adsorbed gold on carbon fines can be lost to the discharge. The studies in this paper aim to standardize laboratory methods for testing activated carbon qualities specific to the gold industry. The investigation focused on size distribution, platelet content, wet attrition resistance, gold kinetics, and gold loading. The results demonstrate that a 96 h attrition test and a gold loading test form a basis for ranking carbon samples based on expected economic performance of the plant. ¦ KEYWORDS Activated carbon, Carbon attrition, Carbon ball-pan hardness, Carbon evaluation, Carbon fines loss, Carbon turnover RÉSUMÉ Le charbon actif sert à récupérer l’or en solution dans diverses conceptions de circuits de broyage d’or, notamment les procédés de charbon en pulpe (CIP, de l’anglais carbon-in-pulp), de charbon en colonnes (CIC, de l’anglais carbon-in-column) et de lixiviation au carbone, ou charbon au lixiviat (CIL, de l’anglais carbon-in-leach). Toutefois, les caractéristiques et la durabilité du charbon actif varient. La manipulation de ce milieu pose des problèmes dès lors que se produisent des pertes de carbone à grain fin dans la décharge des circuits CIP, CIC et CIL. Par ailleurs, l’or adsorbé sur les fines de charbon peut se perdre durant la décharge. Les études réalisées dans le cadre de cet article visent à normaliser les méthodes de laboratoire pour tester les qualités du charbon actif spécifiques au secteur de l’exploitation aurifère. L’étude portait sur la composition granulométrique, la teneur des plaquettes, la résistance au frottement humide, la cinétique de l’or et l’adsorption de l’or, à savoir la capacité du charbon actif à adsorber l’or sur une période spécifique. Les résultats ont montré qu’un test de frottement de 96 heures et un test d’adsorption de l’or constituaient le fondement d’un classement des échantillons de carbone du point de vue économique en vue de trouver l’échantillon générant le meilleur rendement des usines. ¦ MOTS CLÉS charbon actif, dureté de la batée des billes de carbone, évaluation du carbone, perte de fines de charbon, renouvellement du carbone, résistance au carbone INTRODUCTION The use of activated carbon for gold extraction is among the most common processes in modern gold-milling plants. Although gold losses are inevitable in the milling process, operators often focus on reducing gold loss to tailings. One focus area that is important in gold recovery is optimizing the use of activated carbon and examining potential changes to realize improved economics for carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes. Granular activated carbon (Figure 1) is widely used for gold extraction from slurries containing gold-cyanide complexes. This activated carbon—produced from charred coconut shells—is well suited because of its adsorption kinetics, gold-loading capacity, attrition resistance, and ability to be reactivated. The extraction process using activated carbon technology involves adsorbing gold from an aqueous leachate; the gold is dissolved using a cyanide salt and consequently a dicyanoaurate(I) ion (Au(CN)2–) is formed, as noted in equation 1."

Jan 1, 2019

By G. G. W. Thom, A. A. F. Schuldt

At The Steel Company of Canada, Limited, iron oxide dust from the basic oxygen open hearths is being collected by means of electrostatic precipitators. The utilization of this dust, which has been hampered by the presence of zinc and lead oxides and sulphur compounds, is made possible by direct reduction in a rotary kiln. The description of the dust collection system and the results of kiln tests are presented.

Jan 1, 1966

By R. Lowery

TODAY, man uses, at will, the land, the water, and the air to transport himself and his goods everywhere across the face of the world. He no longer thinks with wonder of the magic of conquering these elements - he takes his mastery of them for granted. He is, however, constantly striving to squeeze more and more efficiency from each mode of transport. Man's first method of transporting himself and his goods was, obviously, himself; then he acquired his first beast of burden - woman. Most other two-legged female animals carried their young around clinging to their fur. Human mothers were, generally speaking, furless and their offspring less 'Prehensile, and so slings and other trappings were invented to carry young children. Man's inventive genius soon adopted these devices for carrying other burdens, and for countless centuries woman carried all in order that man could walk unencumbered except by his weapons. Later other ?beasts of burden were trained and used, including dogs, horses, oxen, camels, etc. Man also discovered quite early that he could drag along the ground more than he could carry on his back.

Jan 1, 1956

By E. Bongajum

We present results from petrophysical studies to characterize a Zn-Pb-Ag deposit in Nash Creek, New Brunswick. The measurements are part of an integrated study that includes geological and geophysical data acquired on the property. In order to successfully characterize the ore body, an understanding of the relevant physical parameters and their change with vertical and lateral variations of the target lithology is necessary. The quality of the estimated 3D variation in the physical properties is supported by the presence of several boreholes that randomly span the survey region. Density was measured from cores of thirty-two boreholes across the area. Seventeen of these boreholes constitute two intersecting borehole profiles, which is ideal for locally modeling the 3D distribution of the ore deposit. High densities (>3.2g/cm3) correlate strongly with Zn-rich mineralization zones (low resistivity). Compression and shear wave velocity measurements made from representative core samples of the regional geology range from ~2.91 to ~6.41 km/s for P-waves and from ~1.41 to ~4.20 km/s for S-waves. The lower bounds of these velocity values correspond to regions with a high degree of alteration. Moreover, porosity estimates from rocks on the property suggest that porosities range from 0.35% to 11.79%. Induced polarization (IP) measurements confirm that mineralized samples show a significant chargeability and resistivity contrast with respect to the host rock. Thus, chargeability and resistivity information can be combined to adequately identify conductors associated with mineralization in electrical survey data. Information on these physical parameters and their 3D statistical distribution have serious implications on various aspects of mineral exploration that include: resource estimation, choice of geophysical data acquisition and interpretation, and information for preliminary rock stability assessment.

May 1, 2009

By Ahmad Ghahremaninezhad, Denver H. Cowan

Much of today’s gold is locked within sulphide minerals. These sulphide minerals, including pyrite, need to be subjected to oxidative pre-treatment in order to leach the refractory-gold using traditional methods. Typically autoclaves employing high temperatures between 180?225 ºC, and extremely high pressures between 1,500?3,200 kPa, are used for the oxidative pre-treatment. However, the autoclaves themselves are very expensive, costly to operate and maintain, and produce excess sulphuric acid. This paper studies the atmospheric oxidation of pyrite in ferric sulphate solutions. In general, pyrite oxidation under atmospheric pressure can result in high elemental sulphur production, i.e. less acid generation. Activated carbon has displayed an ability to catalyze the process, achieving reasonable kinetics. The reaction kinetics were investigated by altering acidity of the leaching solution, temperature, catalyst ratio, sparged oxygen and agitation. A combination of X-ray diffraction, scanning electron microscopy, optical microscopy, X-ray fluorescence, inductively coupled plasma mass spectrometry (ICP-MS), and atomic absorption spectroscopy (AAS) were used to monitor the kinetics of the process and elemental sulphur yield. The purpose of this investigation was to determine optimal operating conditions that maximized kinetics of the atmospheric oxidation while maximizing elemental sulphur yield.

Jan 1, 2015

By Scott Hopkins

Simulation tools are preferred for evaluating complex systems due to its ability to mimic reality and quickly evaluate many different what-if scenarios and find global solutions. A simulation model is capable of representing variable and dynamic disturbances that are typically encountered in day-to-day operations; this is where spreadsheet models or linear programs fall short because they cannot account for the dynamic behavior and relationships. The simulation model used for this work was developed by Xstrata-Nickel (previously Falconbridge). The simulation tool is very flexible and can be used to simulate different mining and development methods. The scope of the modeling included production mining, geology, equipment fleets, equipment maintenance and random failures, manpower, shift schedules, and cycle activity times. A case overview of the 170 Orebody will be presented along with the challenges associated with data collection for the model inputs. Results and lessons learned will also be discussed.

May 1, 2008

By L. Shasko, M. Hurlbert

As climate change is increasingly perceived as a problem, and fossil fuel based power production options are increasingly limited through regulatory restrictions and public distaste, future options become constricted. Reflexivity and social learning elicited through qualitative and mixed research methods offer important insight into what future power production pathways might be. Given factors of cost, baseload requirements, and energy density, options such as nuclear may be increasingly accepted. This paper explores this literature and possible methods of pursuing the reluctant acceptance of nuclear energy.

Jan 1, 2020

By J. Jankovic

Numerous advantages have been recognized for solid oxide fuel cells (SOFCs) operating at temperatures of 500-700°C. However, there are several issues related to low temperature SOFCs, such as high electrolyte resistance and high electrode polarization. One of the routes to enhance the electrode performance, particularly for the cathode, is to use new materials with optimized microstructure. In this work, the plasma-spraying technique, recognized to have several advantages over presently used deposition techniques, was used to deposit cathode materials onto ceramic and stainless steel substrates to obtain highly porous structures. Cathode materials with composition of Lao 6Sr0.4Co02Fe0 8O3 (LSCF) were employed in the powder form. The LSCF was prepared from powder precursors with different pore formers and binder levels, or from already produced, single-phase LSCF. The (La0.8Sr0.2)0.98MnO3 (LSM) cathode material was also processed for comparison purposes. The deposition process was developed to obtain coatings with good bond strength, porosity, film thickness and residual stresses. The phase and microstructure of deposited materials were characterized using XRD and SEM.

Jan 1, 2005

By L. O. Cooper

IN THE operation of most mines, hoisting ropes, made of steel, play a very important part in the conveying of men and material between surface and the underground workings. It is obvious that, in order to maintain a maximum degree of safety, certain restrictions must be placed on the loads that may be carried by hoisting ropes, as well as on other factors that may affect the life of the rope. It is the purpose of this paper to suggest ?a new method of defining the necessary restrictions. The three main stresses in a hoisting rope are the static stress, bending stress, and dynamic stress. Crushing stresses, which are also present, are largely indeterminate and may best be allowed for by proper grooving of drum and sheaves, by adequate inspection of cross-over points, and by limiting the number of layers on the drum. They will, therefore, not be considered in this analysis. In the ?recent Ontario regulations, the limiting conditions for the main stresses are specified separately. The static stress is limited by setting a minimum static safety factor of 5.0 The dynamic stresses are allowed for by specifying a minimum capacity factor of 8.5, which has the effect of increasing the safety factor required at smaller depths in a uniform manner. The bending stresses are limited by calling for a drum-dia./rope-dia. ratio of at least 60 for ropes up to 1 inch in diameter and 80 for ropes greater than 1 inch in diameter. One disadvantage of this method is that the controls are too rigid and do not allow the operator sufficient freedom of action within safe limits.

Jan 1, 1951

By K. Hambrice, E. Fauveau

"When it comes to measuring the level of bulk solids, liquids, and everything in between, guided-wave radar technology now offers more level-detection capabilities than ever before. For an ever-widening range of previously hard-tomeasure products such as molten sulphur, liquid ammonia and petrochemicals, guided-wave radar transmitters provide accurate level measurements even under harsh chemical environments, wide variations in operating temperatures and pressures, and low dielectric constants.Great strides have been achieved in making these units easier to configure to a variety of process applications coupled with the simplicity of integrating these devices with most digital communication protocols. These improvements come as welcome relief to process engineers within an expanded range of level applications across several different industries that seek solutions to measuring the contents of tanks, silos, hoppers, bins, mixing basins, and vessels.Because radar transmitters have no moving parts, radar has already established a dominant niche in level measuring that quickly distances itself from mechanical means, which do not hold up as well in dirty service. Radar achieves its nonmechanical level detection capability by measuring the time of flight of the transmitted signal.Known more accurately as time domain reflectometry (TDR), the process involves sending microwave energy down into a vessel. When the pulse of radar energy reaches the product (indicated by a change in impedance), part of the pulse is reflected back toward the transmitter.A receiver measures the exact duration of time between the transmitted and reflected signal — the “time of flight.” The device analyzes this time and ultimately displays the level of the product as a distance in feet, metres, or other engineering units."

Jan 1, 2003