Search Documents

By A. Hekmat-Ardakan

Conventional hypereutectic Al-Si alloys such as A390 are used principally for the casting of components used in wear applications requiring abrasive resistance such as in engine or compressor blocks. A comprehensive study was undertaken to investigate the potential of improving the mechanical properties of these alloys by the addition of magnesium. A thorough thermodynamic study of the effect of the addition of Mg to the conventional A390 alloy showed that Mg2Si starts to form as a primary phase at 4.2% Mg as well as in the products of the binary and ternary eutectic reactions forming the matrix. Experiments were carried out in producing castings with different cooling and solidification rates of alloys with up to 10% Mg. Mg additions were found to increase the hardness over the as cast alloy due to solid solution strengthening. Also, T6 heat treatment greatly improved the tensile properties of these alloy compositions due to the strengthening effect of the theta-Al2Cu phase. The elongation of these alloys generally decreases marginally with Mg content. The most significant property improvement of the alloys with higher Mg content is the substantial increase in wear resistance. This is attributed to the dispersion of smaller particles of Mg2Si and their coherence with the matrix as compared to the large Si particles in the conventional alloy. A new rheoforming process for A390 is presented that improves the processing of the semi-solid slurry. Structure modification elements were also added to refine the primary and eutectic silicon greatly improving the processing of the semi-solid slurry.

Jan 1, 2011

By Niklas Frank

Ore and waste transports form an integral part of any mining operation and represents a substantial portion of the mine´s total operating cost. Mine layout, truck fleet and size, production rates, haulage distances, shift schedules, maintenance strategies etc. are all important and not at all static variables. They all change during the life of a mine and interact in a dynamic way. It is therefore essential for the successful mine management to constantly analyse and optimise the mine's transport systems. Önnerlöv has recently conducted a life-of-mine haulage simulation project for Zinkgruvan Mining, a medium sized, underground zinc producer, located approximately 60 kilometers south of Örebro, Sweden. The main objective of the project was to analyse and optimise the investments required to provide ore and waste haulage under changing conditions over an +10- years period: Deepening of the mine, increased production rates, changed mine layout, changed truck fleet etc. A large number of scenarios has been tested in the simulation model in order to identify the "lowest cost per ton" solution. This paper comprises an introduction of Zinkgruvan Mining and a brief background to the actual project, a description of the simulation model, project conclusions and some useful hands-on tips for mining engineers and project managers how to run a successful simulation project.

May 1, 2003

By D. L. Thompson

Foreword The complete history and early development of the Sullivan mine was fully covered in a paper entitled 'The Development of the Sullivan Mine and Processes for the Treatment of its Ores', prepared by the staff of the Consolidated Mining and Smelting Company of Canada, and presented at the Annual Meeting of the British Columbia Division of the Institute at Trail in October, 1924. At a subsequent meeting at Blairmore, Mr. E. G. Montgomery read a paper on the mine, and in 1926 Mr. M. M. O'Brien brought the subject up to date at the joint meeting of the American and Canadian Institutes at Cranbrook. The present paper is necessarily based largely on these earlier accounts. Discovery and Early Development The outcrop was discovered in 1892 and the property was bonded and later sold to the Sullivan Group Mining Company, of Spokane. From 1896 to 1899, surface stripping and test pits (at A) around the outcrop exposed a vien of sulphides with varying amounts of lead and zinc. In some places, a 35 per cent lead ore carrying 15 ounces of silver was found. These lenses were of commercial value. With the completion of the Kimberley branch of the Canadian Pacific railway, in 1900, some systematic development was started. A shaft l00 feet in depth was sunk (at B). Shaft-house, boiler-room, and compressor-plant were erected, and a steam diamond-drill was put into operation.

Jan 1, 1929

By Earl Gebhardt

The planning and design of mining panels in the Potash Corporation of Saskatchewan Inc., Lanigan Division mine Block B involved a number of investigative techniques. The techniques utilized to gain insight into the viability of mining included 2-D and 3-D seismic surveys, longhole drilling, exploration wells, photolineament, magnetic and gravity surveys, and actual room excavation.

Feb 1, 1993

By Richard Jundis

At the Vale Inco Ontario Operations, the working environment is rapidly evolving with organizational changes, new business systems and software tools. These changes are required in order to meet today?s challenging business environment. Mining professionals are focusing on the development of safe and achievable mine plans to maximize mining value while reducing the potential of project delays and production shortfalls. This paper explores how new design tools, techniques and system designs in mine planning are being developed to optimize the value of every ton of ore mined and processed. To differentiate from other papers on long-term planning, this paper focuses on the concept of business planning at the mines. Business planning is the understanding and optimization of the relationship between mine plans and the value it adds in the overall process. The management and key stakeholders of Vale Inco have recognized that the development of a robust mine planning system and programs are essential for the long-term sustainability of the operations.

May 1, 2009

By Steve Custer, Chris Bennett, Patrick Garretson, Glenn Dobby, Jacques McMullen

"Barrick Gold is in the process of expanding one of its grinding circuits at the Goldstrike property as a response to both increasing ore hardness and increased ore sensitivity to finer grinding as it relates to gold recovery. The plant currently operates with two parallel grinding lines, each with a SAG mill, a pebble crusher, and a ball milling arrangement. As part of determining what additional equipment was to be required, a CEET evaluation program was conducted (CEET is an acronym for Comminution Economic Evaluation Tool). The work included: Development of a hardness ‘model’ for the ore body, as described by SAG Power Index and Bond Work Index;Site benchmarking surveys to fine tune the SAG and ball mill calibrations within CEET;Conducting CEET studies to examine the process options;Comparing CEET results to standard grinding circuit design techniques.The recommendation of the study, presently being implemented, is the installation of an additional ball mill on one of the two grinding lines. This paper reviews the sizing techniques applied, providing a CEET case study for circuit performance analysis and circuit design. OVERVIEW OF COMMINUTION AT GOLDSTRIKEOre feeding the autoclaves at Goldstrike are first processed through two parallel grinding lines. Both lines use SAG mills with cone crushing of pebbles followed by ball milling. A summary of the key circuit parameters is provided in Table 1. Line 1 primarily processes underground Meikle ore, although when no Meikle ore is available, it processes open pit Betze ore. Line 2 processes Betze ore exclusively. The Mill Line 1 P80 objective for Meikle ore is 74 microns. According to the recovery optimization analysis, a P80 of 90 microns was recommended for Betze ore. The potential however exists to perform co-mingling of both ore types and feed the higher grade Betze ore to Line 1, in which case the P80 of 74 microns would be retained."

Jan 1, 2001

By Peter Mitschke, Friedrich Rosenstock, Heinrich Meiler

"The development of the Centrifugal Mill jointly by Chamber of Mines (Johannesburg) and LURGI GMBH (Frankfurt) had been described by L. Kitschen e.al. during the 14th IMPC at Toronto in October 1982. Further investigations, using a 55 kW semi-industrial mill, installed at LURGI's Research Laboratories, were concentrated on efficiency and wear in grinding.The test results showed, that efficiency increases when increasing the ball load between 60 and 80 % by volume. Furthermore, the efficiency is increased by speeding up the mill, thus increasing the centrifugal force to up to 14 times the force of gravity. Applying these findings to grinding of a Canadian iron ore spiral concentrate, a saving in grinding power of 30 % was experienced, when comparing with ordinary wet ball milling.Investigations of several shapes of the grinding chamber cross section and linings and several types of materials showed, that no increase of liner or ball wear will occur compared to conventional ball mills when choosing suitable lining patterns. 1. DEVELOPMENT OF THE CENTRIPUGAL MILLThe centrifugal mill was developed with the aim of finding a grinding unit that can operate at a higher power concentration than the conventional tumbling mills.LURGI felt the necessity for such a mill in connection with a hydrometallurgical process developed at the beginning of the seventies, which incorporated an activating grinding step as one of the essential process features. At that time, the Chamber of Mines in Johannesburg was investigating possibilities of underground wet grinding and preconcentration of gold ores aiming at a decrease of mining costs by reducing the quantities, especially for mines operating at depths up to 3600 m, by changing over from rope hoisting to hydraulic transportation systems. After the Chamber of Mines had initiated the development work on its own, in 1974 a cooperation between the two organisations was started."

Jan 1, 1985

By Colin Hardie, Erik Bartsch, Guy Comeau

"The Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik region has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high grade nickel ore, plant capacity is currently approaching 1,200,000 tonnes per year due to an Optimization Project (FAG to SAG conversion) in 2005 and many recent processimprovements.In 2006, the Raglan Metallurgical Group with assistance from the Xstrata Process Support group decided to make SAG control one of its priorities in order to further increase throughput and improve stability. The original primary mill control logic delivered by the Optimisation Project in 2005 consisted of a simple PID loop controlling the mill charge (bearing pressure) through feed rate changes. Due to the multivariable, non-linear and disturbance dominated nature of the SAG circuit it was quickly found that this traditional PID control strategy was not able to adequately control the mill; resulting in poor stability, frequent operator interventions and less than optimum performance.This paper describes the successful integration of advanced field systems such as mill feed image analysis (Wipfrag) and crusher gap controller (ASRi), into a multi-variable fuzzy logic SAG mill controller. The process of how a strategy for control was developed and implemented directly in the existing control system (exploiting standard system capabilities) is discussed. It is also shown how this approach has provided mill automation which is simple, robust (despite erratic feed characteristics), and delivers both an increase in throughput and a reduction of variability.INTRODUCTIONOriginally commissioned as a Fully Autogenous Grinding (FAG) circuit in 1997, preparations to convert the Katinniq Concentrator Mill to SAG had in fact commenced as early as 1999, but were halted owing to alternative process improvements which achieved up to 1Mtpa as early as 2000. Up until this time, plant process controls had remained more or less static; modifications having been limited to those required by new equipment. Primary mill process controls and related measurements were at this stage limited to:"

Jan 1, 2008

By W. R. Cowan

The availability of mineral aggregates for construction purposes is rapidly declining through inadequate resource planning. restrictive zoning and legislation , and competing land uses. The Geological Branch of the Ontario Ministry of Natural Resources has undertaken to provide aggregate inventory reports for all townships designated under The Pits and Quarries Control Act, 1971, and eventually for all towns hips in heavily populated areas. The reports contain maps and recommendations for extractive zoning by municipalities; of necessity only the largest deposits are given priority recommendations. It is intended that these reports should improve the resource planning in areas underlain by large aggregate deposits. The inventory is only possible because a concentrated effort has been made to map the Quaternary geology of populated areas over the last ten years. Future needs require that we develop methods to determine the extent of poorly defined and buried aggregates and that we look for natural alternatives.

Jan 1, 1978

By Anthony P. Makuch

Dynatec Corporation is an integrated mining services company, providing mine development, operations management, engineering, drilling and metallurgical services to the North American mining industry. Dynatec was the contract operator of the Ken Snyder Mine in Midas, Nevada from start of production in January 1999 to September 2001. This paper summarizes Dynatec?s experience and approach to the use of longhole stoping methods for mining to widths of 1.3 to 2 metres in a steeply dipping narrow vein orebody.

Oct 1, 2001

By Erin N. Legault-Seguin

The Lac des Iles Mine (LDI) is located approximately 100 km northwest of Thunder Bay, ON. The mine has been in operation since 1993. The initial mine production was 2,300 mtpd and increased to 15,000 mtpd following a mine expansion project that was completed in 2001. Effective Oct. 29, 2008, LDI was shut-down under care and maintenance due to low metal prices. Prior to shutting down, LDI was the only primary PGM deposit in operation in Canada and of the few found globally. The complex geology and physical properties of the deposit causes several challenges for the concentrator. This paper will discuss the solutions to the main challenges of attaining nameplate tonnage and achieve satisfactory Pd recovery and concentrate grades.

May 1, 2009

By S. Kursunoglu

The aim of this study was to investigate the effectiveness of Ascorbic (C6H8O6) Acid (AA), Activated Carbon (AC) and Guar Meal (C6H12O6) (GM) as a reductant for the simultaneous complete dissolution of zinc (Zn) and manganese (Mn) from a spent and mixed Zinc-Carbon (Zn-C) and alkaline battery powders in sulphuric acid (H2SO4) leaching. AA was tested previously as a reductant by other researchers while AC and GM were tested as a reductant for the first time in battery recycling. The effects of H2SO4 concentration, AA/AC/GM dosages, reaction temperature and leaching time on the Zn and Mn dissolutions were investigated according to 2k full factorial experimental design and Central Composite Design (CCD) technique; then, a simple optimization study was carried out for comparing the reductants. The optimum reductive acid leaching conditions for AA were determined at 3 hours leaching time, 70°C leaching temperature, 0.5M H2SO4 concentration, 13 g/L AA dosage, 1/20 g/mL solid/liquid (S/L) ratio and 200 rpm stirring speed. Under these conditions, the dissolution efficiencies were 99.9% for Zn and 99.3% for Mn. The best reductive acid leaching conditions for AC were determined at 3h leaching time, 80oC leaching temperature, 1M H2SO4 concentration, 3 g/L AC dosage and 400 rpm mixing speed. Under above conditions, Zn and Mn dissolutions were not complete. At 2M H2SO4 concentration, 10 g GM dosage, 700C leaching temperature, 200 rpm stirring speed, 1/20 g/mL solid/liquid (S/L) ratio and 3 hours leaching time, full dissolution of both Zn and Mn was achieved. As a result, three different reductants were evaluated in this study for complete simultaneous Zn and Mn dissolutions. This paper also compared present test results with previous spent battery recycling studies for Zn and Mn dissolutions. Full valuable metals dissolutions from spent batteries were achieved at low H2SO4 concentrations with AA and high concentrations with GM. Selective precipitations of Zn and Mn from acid solutions were carried out using NaOH and KOH. Using 3M NaOH as precipitating agent at room temperature and at pH 8; 95.4% of Zn and at pH 10; 93.7% of Mn were precipitated from the leach solution. Under the same conditions, using 3 M KOH at pH 8; 91.6% of Zn and at pH 10, 96.4% of Mn were precipitated. Based on the experimental results obtained, an appropriate flow sheet was proposed to recover both Zn and Mn.

Aug 1, 2013

By E. L. Bruce

Red lake is a body of water some thirty miles in length lying about forty miles northwest of the outlet of Lac Seul. It forms one of several large lake expansions on a river which enters the English river from the north, twenty miles below Lac Seul. Before the construction of the National Transcontinental railway a long canoe journey was necessary to reach that part of the English river, and Red lake, two days travel beyond, was one of the furthest outposts of the trading companies in that difficultly accessible triangle of country between Lake Winnipeg, James Bay and the English and Albany rivers. The Hudson's Bay Company post at Red lake is said to be one of the earliest established in the district but there are no records at the post, and as the English and Albany rivers never were used to any great extent as travel routes there is no mention of the place in the diaries of any of the early explorers. Dr. Bell passed through Red lake on his excursion to the Berens river country in 1883, and a brief note mentions that Huronian rocks were seen. To Dr. Dowling, however, belongs the credit for the first thorough description of this basin of sediments and basic volcanics. In 1893 he followed the course of Dr. Bell's trip, of ten years previous, through Red lake to the upper part of the Berens river.

Jan 1, 1926

"A growing public awareness of work-related diseases such as pneumoconiosis and the impact of this awareness on legislative bodies and on the skilled labour market are reasons why the Canadian mining industry must consider dust control of top-drawer importance. Measurements and standards related to the hazard are necessary to control a dust situation and to avoid excessive risk. The author discusses some of the methods of measurement, standards proposed and terminology used in this developing technology. The purpose primarily is to give a better understanding of the basic advances achieved by those who have applied current knowledge with a measure of success."

Jan 1, 1972

By Pierre Gratton, Gordon Peeling

The Mining Association of Canada launched the Towards Sustainable Mining initiative in 2004. TSM’s goal is to improve the mining industry’s performance by aligning its actions with the priorities and values of Canadians. The initiative currently includes performance indicators for four areas: tailings management, energy use and greenhouse gas management, external outreach and corporate crisis management planning. Over the past year, the association has been designing a performance assessment and verification system for these performance areas, as its members prepare to move to external verification of their performance in 2006. The presentation will describe the initiative and its evolution, as well as the challenges faced in developing a verification system applicable to an entire sector.

Jan 1, 2006

By M. Pfeifer, M. N. Brodie, D. J. Barratt

"This paper reviews design trends related to the various SAG mill configuration and drive options available today. The impact of these options on capital and operating costs is assessed, and key technical issues reviewed. The discussion is based on the conventional North American ’pancake’ mill configuration. IntroductionDuring the past decade mill technology has evolved significantly in the following key areas:• improvements in variable speed motors continue with on-going advances in electronics;• ring motors, or gearless drives, are becoming more common in mill sizes 32 ft and larger, with ratings of 10 000 HP and greater;• geared drives have become available up to ratings of 9500 HP per pinion, compared to the earlier 6000 HP guideline;• improvements in speed reducer technology due to the use of carburized and ground precision gearing, make the high speed motor-speed reducer drive more competitive with the direct coupled low speed motor drive;• a unique speed reducer drive is being introduced to this industry which combines ring gear drive pinions with speed reduction. mprovement in gear alignment is claimed, and the overall drive arrangement is more compact than is possible with a conventional speed reducer drive;• the first 38 ft and 40 ft diameter mills have been designed and manufactured; and • application of large multi-shoe bearings have made shell supported mill configurations available for all, including the largest sizes. These designs have flat instead of conical mill shell ends, and have the potential for technical and cost advantages compared to conventional trunnion supported designs.This proliferation of mill design features provides several options to those involved in planning and design of milling plants, and requires more extensive evaluation to optimize mill design features to best suit specific project requirements."

Jan 1, 1999

By G. Azimi, C. A. Ang, F. Zhang

"Nickel recovery from laterite ores generates large amounts of solid and liquid wastes. This is primarily due to the low concentration of Ni (about 1.4 wt%) in the feed ore to the High-Pressure-Acid-Leaching (HPAL) process. It is known that the HPAL residue contains a high concentration of hematite, a commercially important source of iron in the steelmaking industry. However, the balance is natroalunite, containing sulfur, which is a detrimental element in the steelmaking process. Hence, to make the HPAL residue a suitable feed for steelmaking, natroalunite must be removed. The current work is focused on: 1) a thorough characterization of the HPAL residue obtained from Vale, and 2) a systematic investigation of an alkaline leach process to remove natroalunite. The characterization results indicated that there are about 83 and 12 wt% hematite and natroalunite in the HPAL residue, respectively. The leaching results indicate that sodium hydroxide is the best leaching agent, which results in 55 wt% reduction in the sulfur content. The results of this work enable the conversion of an otherwise waste product into a useful feedstock for steelmaking. Furthermore, this project could potentially have significant environmental benefits by reducing the amount of residue produced during the HPAL process.INTRODUCTION Conventionally, crude steel has been obtained by reducing iron ore containing oxides such as hematite (Fe2O3), magnetite (Fe3O4), and wüstite (FeO) in a blast furnace with coke. The product is then refined in a basic oxygen furnace to produce steel with useful properties (McGannon, 1969; Turkdogan, 1978). Steel has been sought for its desirable properties and its application is widespread throughout modern civilizations. Surpassing the growth rate of other materials, the annual demand of steel has increased at a compound growth rate of 5% over the last 20 years (Baddoo, 2008). The global demand for steel was reported to be 1501 Mt in 2016 and demand is expected to double by 2050 (Cullen, Allwood, & Bambach, 2012; World Steel Association, 2016). In recent years, to meet the rapid growth of demand, secondary resources for iron have been identified as strategic sources of iron (Das, Kumar, & Ramachandrarao, 2000; Li, Sun, Bai, & Li, 2010; Matschullat et al., 2000). The residue produced from high-pressure acid leaching (HPAL) of laterite ore has been identified as one of the important secondary sources of iron (McDonald & Whittington, 2008). Laterite ore represents 60% of the world’s nickel resources and accounts for approximately 40-50% of the world annual nickel production (U.S. Geological Survey, 2016). Therefore, the amount of iron residue produced by the process is substantial and its utilization will produce both economic and environmental benefits."

Jan 1, 2017

By C. H. Knight

"THE OBSERVATIONS that follow are confined to simple wet cyclones such as the cylindro-conical unit developed by the Dutch States Mines and marketed in America under the trademark 'Dorr-Clone'. Energy to do the work comes from the inlet velocity of the feed slurry, which is usually pumped' to the unit by a centrifugal pump.Such cyclones are simply classifiers of enormous capacity and depend for their separating effect on differences in rates of particle settlement. These particle settling rates, of course, vary with particle size, particle density, particle shape, pulp viscosity, and pulp density.The dilution of the overflow product affects both pulp viscosity and pulp density. In most operations, the temperature and the composition of the liquid -hence its viscosity --are fixed, but both pulp viscosity and pulp density can be changed by changing pulp dilution.Since the separating effect depends on differences in rates of particle setting, a perfect split with 100 per cent of the particles coarser than a given size in the underflow and 100 per cent of the finer sizes in the overflow is not possible. Just how far the separation departs from this perfection can be calculated rather exactly from the following principles, which also apply to mechanical classifiers. In removing or settling out of the overflow product all particles up to a specified size, some of the finer particles must settle out simultaneously."

Jan 1, 1955

By R. Kaibyshev, I. Zuiko

"The effect of thermomechanical processing (TMP) including cold working by tension or rolling before aging on mechanical properties and a dispersion of secondary phase particles of an AA2519 alloy (Al–5.64Cu–0.33Mn–0.23Mg–0.15Zr–0.11Ti–0.09V–0.08Fe–0.01Si (wt. %)) was examined. It was shown that the use of tension to impart pre-strain =10% in the alloy provides the best combination of properties in peak aging condition of the material. The AA2519T87 alloy processed by tension exhibits the yield stress, ultimate tensile strength and elongation to failure of 425.4±2.4, 475±2.4, 12.1±0.4, respectively. The one pass rolling leads to -5% decreases in yield stress and –20% decreases in ductility. Dislocations serve as heterogeneous nucleation sites for ?'-phase precipitation. The positive effect of tension is attributed to the formation of more homogeneous dislocation structure, uniform distribution of ?'-phase particles with higher aspect ratio. Precipitation of the O–phase plates on {111}a habit plane was detected. In addition it was shown that the low angle boundaries are heterogeneous nucleation sites for ?' and O particles.INTRODUCTION Precipitation-hardened alloys are a commercially important group of the materials because their mechanical properties can be modified by treating and changing the microstructure. Age-hardenable aluminum alloys belonging to the Al–Cu–Mg system are widely used due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance attributed to the highly efficient strengthening by the ?'-phase (Palmer, StJohn, Nie, & Qian, 2017). An AA2519 alloy exhibiting superior mechanical properties among high-strength Al–Cu alloys (2XXX-serie) due to minor Mg additives. It is known that, in alloys with high Cu/Mg ratio (=5.6) the classic precipitation sequence (Palmer et al., 2017; Wang & Starink, 2005; Wang et al., 2010) of supersaturated solid solution (SSSS) decomposition occurs: SSSS ? GP zones (Al3Cu) ? ?? (Al3Cu) ? ?' (Al2Cu) ? ? (Al2Cu) (1)"

Jan 1, 2018

By Dave Ecobichon, Éric Côté, Simon Nickson, Michel Leclerc

The feasibility assessment of a mineral deposit requires the construction of a geo mechanical model of rock mass properties, for the purpose of preliminary mine design. The Noranda Technology Centre has been involved in the development of geomechanical models for several mineral deposits at the feasibility stage. Each model is constructed through intact rock testing, geotechnical core logging, geotechnical mapping and rock mass classification. Rock mechanics principles are used to develop conceptual stope designs and propose possible mining sequences. This methodology is applicable to both new mining projects and to the development of new areas within anoperating mine. This paper explains how the geomechanical model is developed and reviews its application to several case studies.

Jan 1, 1996