Search Documents

By Alisa M. Caswell

Outline: 1. Syncrude: Who are We? 2. Energy Use at Syncrude 3. Historical Energy Focus at Syncrude 4. Case Studies for Process Variable Monitoring 5. Extraction Flood Water Temperature Management 6. Fired Heater Tuning 7. Critical Factors for Success Syncrude: Who are We? ?Syncrude is a Joint Venture Operating Company with one product: Synthetic Crude ?Production Capacity: 350 kbbls/day ?Primary Energy Sources: ??Fuel Gas + Natural Gas ?? Coke ?? Electricity ?? Diesel

May 1, 2008

By D. M. Morrison

"Microseismic systems at five mines in the Sudbury Basin provide the basic data for Falconbridge Limited's rockburst research. Daily and long-term analysis of this data as well as underground observations has confirmed the fault-slip mechanism of rock bursting at three mines. A detailed analysis of the complete history of Falconbridge Mine is being conducted and Distinct Element numerical models are being used to simulate both the stick-slip behaviour of faults and the dynamic effects of the induced vibrations on rock and backfill. University research includes acoustic tomographic imaging of the rock mass based on seismic wave propagation and collection of full micro seismic waveforms to allow application of advanced seismic and statistical analysis techniques. INTRODUCTIONFalconbridge Limited currently has five mines operating in the Sudbury Basin: East, Lockerby, Onaping, Fraser, and Strathcona Mines, which along with the Falconbridge open pit produced 2.8 million tonnes of ore in 1986. The underground mines range from about 600 m to 2000 m below surface and one of the consequences of mining at these depths is the occurrence of rockbursts.Research into rockburst phenomena at Falconbridge began over 25 years ago and research is continuing in an effort to avoid the problem by improved mine design, to protect mine openings from damage by design of effective support systems and to better understand the processes which precede a major fault slip rockburst. Since the early 1980s, significant progress has been made due principally to micro seismic monitoring and advances in microcomputer technology coupled with detailed underground investigations.It is now possible to identify the fault-slip mechanism as the cause of many of the rockbursts which occur at Falconbridge mines. By gaining an understanding of effect of mining-induced stresses on the pre-existing geological structures, areas which may experience rock bursting can be identified and can be protected against severe damage by appropriate support techniques."

Jan 1, 1989

By J. Hedderson, J. Starkey, S. Reeves, B. Hilscher

"As ore sorting becomes more common, it is important to quantify its impact on comminution circuits in order to precisely predict its effect on throughput, grind, and mill operating conditions. Since sulphides and other valuable minerals are often softer then the surrounding waste rock, the ore kept by a sorting system is typically softer than the average ore. In order to accurately forecast production, new measurements of hardness need to be performed on the new concentrated mill feed. This paper proposes a methodology to examine this effect quantitatively at an early stage of project development using the SAGDesign test.INTRODUCTION The application of ore sorting in the mining industry is one of the most promising recent technologies with the potential to cause step change in the way concentrators are designed. Most typically, ore sorters are used to sort a given ore flow for grade, either to reject waste from the mill feed, or rescue ore from the waste pile. Ore sorting technologies have been successfully applied at many mining properties in various forms and while the technology has reached or is reaching maturity in other industries, it is still in development in the mining sector. As a result, there is not yet a general consensus on the considerations that need to be made when designing a plant with ore sorting from a feasibility level above and beyond what is commonly performed as best practice. This paper will discuss those considerations and propose a methodology for integrating ore sorting into a comminution circuit at the design phase. Due to the linearly additive nature of the SAGDesign Test results, a “hardness balance” can be developed to estimate the ore hardness which would be measured in any sorting mass split using only two data points. This will allow a design engineer to make more informed decisions as to the most appropriate mass split to select in relation to the incurred operating costs and grinding circuit sizing."

Jan 1, 2019

By Michel Guillot

Gaz metal arc welding is commonly used for producing large frames and assemblies. Even for light aluminum and thin wall assemblies, the GMAW technique is increasingly preferred over the GTAW technique. This is particularly true where the welding gun motion is achieved accurately with automated or robotic systems and when using pulsed or regulated metal deposition. In this study, butt joints in floor welding position are tested at speed ranging from 1.5 to 16 m/min. Attempts are made of find parameters providing good and repeatable joint quality with minimal distortion and good appearance even at high travelling speeds. Taguchi experimental plans are proposed with different parameters tested with sheet metal samples. The parameters include typical GMAW machine settings, joint preparation geometries, wire gages, gun angles, wire feeds, and more. The robot motion speed and the proximity of the part are also considered. Direct monitoring of machine welding current and voltage is achieved. Once is found the best set of parameter settings, additional tests are carried out to verify the repeatability of weld quality. Secondly, these conditions are applied for joining and testing a floor panel made of several extrusions. Weld quality is established with Vickers micro-hardness measurements, cross section geometries of the weld pool including penetration, tensile tests and metallographic observations to establish the amount of porosity and weld microstructure in the HAZ.

Jan 1, 2011

By Robert G. Boutilier

So far, most social performance monitoring systems have not gone beyond listing the impacts on various stakeholders. Executives have had to rely on intuition to devise interventions that would improve the impacts. This paper describes a survey process, known as the Stakeholder 360 (S360), which eliminates much of the guesswork. The paper reviews key studies showing that raising the levels of communication, trust, and common vision among stakeholders leads to the acquisition of the resources needed to improve the socio-economic situation. Therefore, the Stakeholder 360 measures the levels of these three factors in the relationships between a company and its stakeholders, and among the stakeholders themselves. In a validation study at a gold mine in rural Papua New Guinea, the S360 produced a socio-political ?roadmap? that showed management and stakeholders alike which relationships need more communication, trust, or common goals/vision. Management used the findings to create alliances that helped the government move forward on a regulatory regime for the mine closure. The community used the findings to focus its planning for life after the closure. An S360 survey conducted six months later revealed a decline in dependence on the mine and an overall increase in levels of mutual understanding.

May 1, 2002

By V. W. Shtenko, B. J. Ennis, P. H. Bridge

"The northeastern region of British Columbia contains large quantities of high-quality metallurgical coal. To market the coal, it was necessary to provide the required infrastructure which included rail access. This paper presents the role of the British Columbia Railway in the northeast coal development.In 1976, B.C. Railway undertook to study two main routes, one originating at Chetwynd and the other at Anzac, both located on the main line, north of Prince George. The routes studied are briefly described, detailing the methodology and engineering analysis carried out to permit the selection of a single route that would be the most cost effective, taking into consideration the construction, maintenance and operating costs. The operating parameters, track and grade standards, anticipated tonnage, construction costs and the final route selected are also presented.Pre-engineering analysis and studies of the route selected originating at Anzac, known as Tumbler Ridge Branch Line, and which commenced in 1977, were concluded in 1978. New mapping was developed to a scale of 1:2000 with good vertical and horizontal control. Based on the mapping data, terrain analysis, and designs developed, an estimate of construction costs and schedule of work was developed.Authority to proceed with the final design and construction was provided in December 1980, with the first shipment scheduled for December I, 1983. Final designs of all structures are discussed, including schedules, cost to completion, and control systems utilized. The decision to electrify the Tumbler Ridge Branch Line and related topics are discussed, with a brief description of train operations. The present status of the project is also presented."

Jan 1, 1983

By S. Nakamura, K. Fujiwara, S. Hirosawa, S. Tsukamoto, Y. Koshino, Y. Aruga

"In this study, hardness test, differential scanning calorimetry(DSC)and transmission electron micros copy were carried out to investigate the age-hardening behavior of Al-Mg-Si alloy with a Mg+Si concentration of 1.5mass%, and a Mg/Si ratio of 1.0. Pre-aging treatment was conducted for the solution-treated and then water-quenched specimen at 100, 80, 60, 40, 20 (natural aging), 0 and -20°C for 20min or 5h, followed by artificial aging at 170°C for 20min. It was found that when pre-aging time is prolonged from 20min to 5h, the bake-hardening response is deteriorated irrespective of the pre-aging temperature. In particular, the specimens subjected to pre-aging at 20-40°C for 5 h hardly increased the hardness with the subsequent artificial aging. From the results of DSC measurement, it was suggested that as pre-aging temperature is lowered, the amount of solute clusters formed during pre-aging, i.e. Mg-Si clusters and Si-rich clusters, is decreased, but the ratio of Si-rich clusters is increased, resulting in the deteriorated bake-hardening response.INTRODUCTIONIn recent years, Al-Mg-Si alloys have been widely used forautomotive body panels due to their excellent characteristics such as high strength-to-weight ratio and good formability. Their strength is increased not only by artificial aging during paint-bake treatment; i.e. “bake-hardening”, but also when kept at room temperature(RT);i.e. “natural aging”, in association with the suppressed bake-hardening response. Such a “negative effect of two-step aging” has been a serious problem because Al-Mg-Si alloy coils are unavoidably maintained at RT in the manufacturing process of body panels; e.g. shipping and storage. However, it was reported that pre-aging above 70°C before the two-step aging can restore the bake-hardening response, and such an improvement is related to the formation of solute clusters(Sato, 2006; Abidet al., 2010; Takaki et al., 2014; Zandbergen et al., 2015). From the comprehensive analysis by three-dimensional atom probe (Aruga et al., 2014 and 2015), it is believed that Mg-Si clusters formed during pre-aging transform into the strengtheningß"" phase, whereas Si-rich clusters formed during pre-aging act as a detrimental precursor of ß""phase. In this study, it was aimed to investigate the effect of pre-aging conditions, especially pre-aging temperature and time, on the formation of solute clusters during pre-aging, in order to elucidate the mechanism of the age-hardening behavior of an Al-Mg-Si alloy."

Jan 1, 2018

By W. M. Williams

The Canadian steel industry is now in many ways a mature one, having achieved many technical successes during its hundred-year history. It is interesting to look back over this period, to learn something of the histories of the different producers and of the people and forces that shaped their development. The following article provides a thumbnail sketch of the Canadian steel industry as it exists today. It is intended for the general reader, not for the specialist who will want to consult the several books and theses written on the development of the industry during the last hundred years. The famous Les Forges du Saint-Maurice, an important iron producer for a century and a half, provides a natural historical starting point for a look at the four major players - Dosco, Algoma, Stelco and Dofasco - who have provided most of the hundreds of millions of tonnes of steel, in every form from horseshoes to tinplate, needed in the twentieth century. The smaller companies which have sprung up in the last 20 or 30 years are dealt with briefly - but only because their history is so recent. Not so long ago the mini-mill, based on scrap rather than on the blast furnace, was thought to be specially suited to the economies of the smaller developing countries of the Third World. However, recent history has made it evident that the small plant, specializing in a few basic products (e.g. reinforcing bar) or taking advantage of special circumstances, can successfully compete with the large blast furnace/primary steel producers.

Jan 1, 1999

By J. Illescas, N. C. Murray

This paper provides an economic comparison and technical evaluation of different approaches for copper recovery from small-scale resources such as historic tails, dumps, pond and pit water as well as acid mine/rock drainage. Factors such as the location, the availability and cost of reagents, power availability and cost and a local market for end product alter the preferred processing technique. A number of scenarios are presented and technologies considered include; solvent extraction, ion exchange, sulphide precipitation, cementation, copper sulphate crystallization, membrane (RO) and copper cathode production.

Jan 1, 2014

By U. Martin

Advanced copper materials for conducting applications require an optimal combination of high mechanical strength at ambient and moderately elevated temperatures together with superior electrical and thermal conductivity. Mechanical alloying under repeated cooling of the milling vials in liquid nitrogen has been applied to produce ultra-fine grained (UFG) oxide dispersion strengthened (ODS) copper with a high yield strength at ambient temperature. In the present study ODS copper was manufactured by mechanical alloying of copper powder and 3% by volume of incoherent oxide dispersoids. During the high-energy milling a homogeneous distribution of fine dispersoid particles (diameter nearly 100 nm) can be achieved in the powder. Samples with a density of more then 97% of theoretical value were produced by uniaxial hot pressing under 650 MPa at 600°C for 20 minutes. The high yield strength at ambient temperature can be described by a linear superposition of the Orowan stress for particle hardening and of ultra-fine grain strengthening according to the Hall-Petch mechanism. Simultaneously, a best value of 75% IACS could be obtained for the electrical conductivity. The creep behaviour of ODS copper in the temperature range from 500°C to 700°C is described within the frame of diffusional creep deformation.

Jan 1, 2007

By Manouchehr Oliazadeh

Talc is used as a gelating, diluting, antimould and softening agent in the pharmaceutical industries. This article reviews efforts made for producing pharmaceutical grade talc from a mine located in the west of Iran, called Masoud Abad. Reaching to the pharmaceutical standards, was the principal goal of the talc beneficiation. Methods such as flotation and leaching were applied to eliminate the impurities. Considering to the negligible Fe content of the ore, the major impurity was calcium carbonate and to some extent dolomite. Depressants used in froth flotation were dextrine, quebraco and sodium silicate. Variation of collectors such as oil petroleum, paraffin, stearic acid were also used. After optimization of the effective parameters, followed by two stages of flotation (rougher and cleaner) acid leaching process was also applied as a complementary step to remove the impurities. CaO impurities in the sample was 11.63% which reduced to 1.03% after two stages of flotation, and finally reached to 0.03% CaO by leaching process. This figure is more lower than the world pharmaceutical standards (i.e. <0.6 % CaO). The highest recovery was 55% at the best conditions. Other impurities (i.e.As, lead, heavy metals ,?) which were at standard levels, confirmed by the authorized health organizations.

May 1, 2001

By Marko Lampi, Ross Andrews, Jouni Pihlasalo, Robert Matusewicz

With widespread discussion on reducing carbon, sulphur and other emissions, use of sustainable energy sources and the pivotal circular economy theme, consideration needs to be given to pyrometallurgical operations broadly and more specifically, non-ferrous metallurgy. These themes present a number of challenges in terms of current operations and the view of processing the metals which are largely taken for granted in day to day living. This paper considers how these themes will impact pyrometallurgical flowsheets using the non-ferrous base metals as an example. It will examine the flowsheet chain to offer views on the boundaries of flowsheet optimization and the application of available tools to meet these future goals and challenges. INTRODUCTION The themes of reducing footprint through lowered CO2, S and other emissions, together with process sustainability (e.g. lowered energy) and links to the circular economy are well known to everyone in the metals industries. Whether it is reducing greenhouse gas emissions or analysing the importance of metals recycling in the circular economy, all these themes carry with them the fundamental premise of any change being considered; how can you best optimize a system to meet your aims? Of course, this depends on the available tools and the approach used for optimisation.

Jan 1, 2019

By D. Beneteau

Plotting sets of data collected over time using a frequency-magnitude distribution is common with both earthquake and mining seismology. A Time-Between-Events (TBE) analysis technique simply makes use of the inter-event times and b-values (slopes of the best fit lines on the frequency-magnitude charts) from the same set of data. Four distinct patterns in TBE versus Event Magnitude have been found which suggest whether there are constant seismic sources causing populations of data, or if the smaller and larger events, within the population represent varying seismic sources. Different rates of events, identified as TBE-rates in this study, may suggest whether the events are blast induced, or not. This study was done using actual seismic datasets from hardrock mines in Canada and Australia. This was to verify the applicability of the method to multiple mining environments and to determine the practicality and implications of this methodology to enhance the interpretation of seismic source mechanisms The results of the TBE technique and other proven techniques are combined into a Seismic Mechanism Assessment Worksheet. This is a tool that allows operators to compare trends within seismic datasets with assessments of in-situ rock conditions. The goal is to enhance the understanding of rockmass failure mechanisms.

Nov 1, 2011

By H. C. Cooke

"The Part of the Eastern Townships dealt with in this paper is shown in the accompanying figure. Each rectangle represents one of the topographic maps published by the Department of National Defence on a scale of one mile to one inch. Each sheet covers an area approximately 24 miles long and 17 miles wide, or slightly more than 400 square miles. The north-western part of the area figured, comprising the Upton, Aston, Becancour, and the two unnamed sheets, (Three Rivers and Yamaska), together with most of the Lyster, Drummondville, and St. Hyacinthe sheets, is largely covered by clays and sands deposited in interglacial and post-glacial time in the Champlain estuary, so that outcrops are widely scattered and in-formation is correspondingly sketchy. In the remainder of the area figured, comprising more than 4,000 square miles, outcrops are reasonably numerous and have been mapped on a scale of one mile to one inch, and the structure is moderately well understood.The Eastern Townships was an area of intense orogenic disturbance, apparently beginning late in the Cambrian or early in the Ordovician, and continuing till well on in the Devonian period. During this long period, which may have lasted for a hundred million years or more, the area was subjected from time to time to intense thrusts from the east and southeast. Each of these caused folding of the rocks, accompanied by faulting, raised parts of the area above sea-level, and presumably created ranges of mountains. Long periods of erosion cut away the mountains and reduced the area nearly to sea-level after which subsidence carried it below sea-level, and permitted further sediments to accumulate before the next thrust initiated the next cycle.The first of these movements, as stated, appears to have been in late Cambrian or early Ordovician time. The group of rocks known as Caldwell was folded and, south and east of the town of Asbestos, was thrown into great drag-folds before deposition of the next overlying series, termed the Beauceville, began. Unfortunately, the date of this orogeny is very imperfectly known, because both series of rocks have been so crushed and sheared that almost all fossil remains have been destroyed. Graptolites, found in one place in slates generally considered Beauceville, give that series a tentative Middle Ordovician age. In the Caldwell rocks, which underlie the Beauceville with great unconformity, no fossils whatever have yet been found. Thus, if the Beauceville rocks are correctly dated as mid-Ordovician, the best that can be said of the movement folding the Caldwell is that it took place at some time before Middle Ordovician."

Jan 1, 1949

By J. G. Ross

A DESCRIPTION of the block-caving system of mining as practised at the King mine of Asbestos Corporation, Limited, Thetford Mines, Que., was presented. at the Annual Meeting of the Institute held in Quebec city, in April, 1934. The paper was published in the Transactions of the Institute for 1934. There has now been recovered, by this method, one million tons of ore, and a review of experience indicates that the method was well planned and has been executed smoothly. In approaching the problem of selecting the type of mining best adapted to this deposit, the method had to be one which would be low in cost, use no wood, and not disturb the surface immediately bounding the ore-body on two sides. Prior to 1931, block-caving had been considered but rejected, as it en-tailed disturbance of the surface area which lay within a 45° angle of the lowest contemplated workings, if the practice of such mines as Ray, Miami, Inspiration, and Morency, where this type of mining has been used extensively, was followed. At these properties there have been mined large tannages at outstanding low costs, but an extensive surface area has been disturbed in each case. In some instances, townsites in the mining area have had to be abandoned, and dwellings, not considered worth moving, have been allowed to fall into the depression. A study was made of the principles involved in the various types of block-caving, the existing information on ground movement, subsidence, etc., also being carefully analysed. Toward the end of 1931, a plan was conceived whereby the country adjoining ground being caved might be held permanently in place and undisturbed. The success of such a scheme was essential to the application of block-caving at the King mine on account of property boundaries, the Quebec Central Railway right-of-way, and expense of moving buildings. Study of existing data on caving and movement of rock, caused by sub-surface excavations of sufficient unsupported area to result in failure of the backs, indicated, in practically every instance, that such movements followed certain definite laws of mechanics.

Jan 1, 1936

By Geoff Goodyear

UHNL Corporate Profile ? Providing Helicopter Services since 1963 ? A Newfoundland Company head-quartered in Goose Bay, Labrador ? Operations, while primarily Atlantic Canadian, extend across Canada, the Arctic, Greenland ? 16 aircraft, all single engine / VFR Typical Industry Mission Profiles & Work Environments ? Types of missions include: ? Air Taxi & Executive Transport ? Mineral Exploration ? Forest Fire Suppression ? Medivac ? Wildlife Management & Research ? High Angle Rescue and Ice Blasting ? External Load & Long Line ? Mountainous Terrain Operations ? Aerial Application ? Power line Patrols & Construction The Helicopter ? Essentially the same aerodynamic principals as fixed wing but with some mechanical variations on the theme

May 1, 2001

By H. Hitchen

THE object of this paper is to present the various facts that l1ave been revealed during lengthy investigations into the performance of all types of ropes on different hoisting installations. It then goes on to suggest means by which most of these findings could be usefully employed to obtain more economical rope lives with increased safety. SHAFT HOISTING ROPES Four basic designs of ropes are now employed for hoisting duties: (1) Six-strand, round strand ropes with fibre cores. (2) Six-strand, triangular strand ropes with fibre cores. (3) Non-rotating, multi-strand ropes. 0) Locked coil ropes. Round Strand Ropes (Figure 1) Very solid and reliable ropes can be obtained with this simple geo-metric design of strand. 1&apos;1?iangula1? Strand Ropes (Figure 2) Owing to the fact that the wires in the strands are bent over a triangle, they do not seat quite so solidly as when they are bent over a circular core wire, as is the case with

Jan 1, 1963

By E. Krause

The oxidation of Fe(II) with S(IV) and oxygen can be used advantageously in leaching systems requiring both Fe(III) and sulfuric acid; e.g., heap leaching of sulfide-containing ores or concentrates. The oxidation of Fe(II) with SO2/air is several orders of magnitude faster than with air alone; rates of up to ?20 g/L&apos;h were observed at 25°C. The reaction proceeds via an intermediate orange-red mixed-valence Fe(II)/Fe(III) sulfite complex, which is present at an essentially constant concentration throughout most of the oxidation process. The oxidation rate of Fe(II) is approximated by the formula -d[Fe(II)]/dt = k [S(IV)] [02]0&apos;3. The concentration of the mixed-valence complex, and thus the iron oxidation rate, decreases with increasing acidity. Certain impurities, such as SCN- and thiourea, negatively affect the rate. The oxidation reaction 2Fe2 + SO2 + 02 4 2Fe3+ + S042- is accompanied by the side reaction H20 + SO2 + 1/202 4 H2SO4. The side reaction becomes particularly important at low temperatures and whenever the oxygen mass transfer is insufficient with respect to the rate of addition of S(IV). Thus, effective oxygen mass transfer is essential for achieving high oxidation rates with minimal acid formation. The activation energy was estimated as 141 kJ/mol over the temperature range 10-35°C.

Jan 1, 2006

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By H. J. H. Pieterse

Agitation requirements in oxidation autoclaves can vary widely depending on the mineralogy of the feed material and the specific process selected. Before selecting an agitation system it is important that the client specify the desired throughput, mineralogy, chemistry, kinetics, compartments, overall retention time, and the desired oxygen utilization. In selecting the agitation system, the factors mentioned above as well as oxygen solubility, oxygen mass transfer coefficients, and specific power are evaluated. Much research effort has been directed toward open tank systems for fermentation and oxidation processes. However, for high pressure autoclave oxidation processes little information is available. In this review the author&apos;s experience in the autoclave industry and some of the available literature are utilized to compare the installed power per unit volume with some of the methods proposed for open tank oxidation. Equations that appear to give results close to that experienced in the industry have been identified. Further work is required in this area to develop a higher degree of confidence in the ability to predict the power required for any given case.

Jan 1, 2004