Search Documents

By C P. Gravenor

In 1953, a deposit of sedimentary oolitic iron ore was discovered in the Clear Hills area of northwestern Alberta. Since that time, detailed drilling has outlined reserves in excess of 200 million tons of ore grading 30 to 35 per cent iron. Attempts to physically beneficiate the ore to meet blast furnace or direct reduction feed specifications have been, in general, unsuccessful. In 1960, Premier Steel Mills Limited and the Research Council of Alberta jointly sponsored a pilot-plant test at the R-N Corporation at Birmingham, Alabama. About 5,000 tons of ore were treated, and briquettes containing 90 per cent Fe were produced, with 83 per cent recovery. At the same time that the R-N tests were being made, the Research Council initiated a program to produce high-purity powders by chemical methods. Several purification techniques were investigated; hydrochloric acid dissolution of reduced ore was finally adopted. Briefly, the steps involved in this acid process are as follow

Jan 1, 1964

By David Stone

North American Palladium is the owner/operator of the Lac des Iles mine located 115 km north of Thunder Bay, Ontario. The mine has produced an average of 65,000 ounces of palladium since 1994. Lac des Iles is currently undergoing the first phase of a major expansion that will increase ore production from 2,400 tons per day to 15,000 tons per day. A future expansion is being contemplated for 30,000 tons per day. The current expansion will increase palladium output to 250,000 ounces per year. The mine plan for the ultimate pit results in an excavation 1 km long by 800 m wide and over 450 m deep. This makes the ultimate pit at Lac des Iles one of the ten deepest open pits in the world, and the largest in Canada. This paper outlines the geotechnical data collection and design methodology for the ultimate open pit at Lac des Iles.

May 1, 2001

By J. Gogal

Cameco's Cigar Lake Operation (CLO) started commercial uranium ore production in 2015. Initial mining was focused in areas of the ore body with relatively low concentrations of elements of concern (EOCs). As mining progressed into areas of the ore body that were richer in EOCs, some statistically significant behavior of certain analytes was noted in the water treatment circuits. It was ultimately found that the CLO ore body natively hosts numerous alkyl arsine compounds in addition to inorganic arsenide minerals. The alkyl arsines were found to be recalcitrant to typical adsorption on ferrihydrite, with the degree of recalcitrance associated with the degree of alkylation. A number of changes to the process circuits and water balance were performed and planned in order to inhibit the transport of alkyl arsines from the ore stream into the process water stream, and to optimize the overall site water usage. In some instances, the interactions of equipment in conjoined circuits of the process had controlling effects on the behavior of the overall circuit. Work continues to iterate upon the capital design features in order to further tighten the water balance, and to optimize water usage and operating costs.

Jan 1, 2020

By K. Duckworth

"AbstractA new electromagnetic depth sounding technique was applied to the measurement of salt thickness above the workings in the Central Canada Potash Mine at Colonsay, Saskatchewan. The initial tests indicate that this new technique can measure salt thickness and that the technique possesses operational feature s which make it possible to monitor trends in salt thickness throughout the mine. The technique can be applied using existing equipment, but the tests do indicate the desirability of developing equipment with features specially suited to the mine environment.IntroductionTESTS were conducted in the Central Canada Potash Mine at Colonsay, Saskatchewan during 1974 and 1975 to determine if a new technique in electromagnetic depth sounding could provide a convenient means of measuring salt thickness above the workings. This new technique, which was described by Duckworth (1975), offers operational features which appear to be advantageous in this particular situation.The problem requires that soundings be made upward from the mine workings to the base of the second red shale. This shale forms an impermeable seal on top of the Prairie Evaporite. A knowledge of this salt thickness is of interest due to the need to avoid any possibility of the workings rising to cut the red shale. Another desirable objective is the detection of any disruptions of the red shale. Ideally, this should be done ahead of the workings in order that such areas of disruption may be avoided."

Jan 1, 1977

By J. George Gregr

"This paper gives a brief review of grinding mills installation procedures with special emphasis on future maintenance. The importance of cooperation between the customer, construction contractor and manufacturer's representative is discussed, as well as the imparlance of complying with standards, specifications and the keeping comprehensive installation records.Fundamentals of mill maintenance are explained with the aim being to maximize the equipment availability and to minimize unscheduled downtime. The paper also includes development of wear items design, based on operating conditions, drive components and bearings, and how to keep large gears healthy thus eliminating surprise failures.Experience with installation of a large gear on a 34-foot diameter mill in Lornex and successful application of a computer program for the gear alignment on the mill are given.IntroductionSuccessful operation of a concentrator begins with the engineering of the project and continues through selecting the right equipment, its installation , start-up period, and ends with final tuning of the process. machinery and the human factor into an efficient and viable industrial complex.The following is a brief review of grinding mill installation procedures with special emphasis on future maintenance. Fundamentals of mill maintenance are discussed with the aim being to maximize the equipment availability and to minimize unscheduled downtime, with some specific points on key grinding mill components such as bearings and drives.Finally, the experience is recounted with the installation of a large ring gear on a 34-foot diameter mill at Lornex, and the successful application of a computer program for the gear alignment on the mill."

Jan 1, 1985

By D. Chadwick, J. W. Matousek

Between 1860 and 1890 -- from the time of the American Civil War to the last decade of the 19th Century -- nickel production in North America was dominated (even monopolized) by the output of the industrial complex of the Gap Nickel Mine near Lancaster, Pennsylvania and the American Nickel Works in Camden, New Jersey. In some years, from one sixth to one third of the world's metallic nickel supply came from this enterprise. Mining and smelting were conducted at Lancaster; a matte of high iron content was shipped to Camden for pyrometallurgical and hydrometallurgical refining to produce nickel metal, copper sulfate, and cobalt oxide. The high purity nickel product was rolled into sheet for marketing, primarily for coinage, as nickel had few other uses at that time. The undertaking experienced all of the problems that face the mining and metallurgical industries of today: declining reserves, high labor and fuel costs, high transportation costs, fluctuating demand and prices, pollution concerns, and foreign competition. The technical features of the geology; the mining, smelting, and refining operations; and some of the economic aspects are assessed. The view is taken from that of the present time -- seeking those lessons from history that we are supposed to learn or face the prospect of repeating the mistakes of the past.

Jan 1, 2005

By L. Vollert

"The application of pneumatically-assisted fluidized bed flotation, specifically the ERIEZ HydroFloatTM technology, has found widespread use in non-sulphide processing (particularly phosphate, potash and coal) for the recovery of coarse particles. In gold processing, centrifugal gravity circuits and flash flotation cells are typically employed for the recovery of coarse and near-size liberated gold which tends to accumulate in recycled grinding streams due to bypass to the classifying cyclone underflow streams owing to the higher specific gravity of these gold particles. Early removal of this gold from the grinding circuits contributes toward the reduction of downstream processing losses as a result of overgrinding and particle shape deformation in the case of flotation processing, longer leach residence times in the case of extractive processing, and surface occlusions in the case of both flotation and extractive processing. Furthermore, recovery to bullion attracts higher payment terms by way of comparison to concentrate sales in the case of copper-gold concentrators. This paper assesses the application of pneumatically assisted fluidized bed flotation for the recovery of coarse liberated gold through the analysis of piloting data generated from the operation of a continuously operated 16 inch ERIEZ HydroFloatTM unit treating a sized coarse grinding circuit stream. The paper presents the stage recovery by size performance of the ERIEZ HydroFloatTM unit together with quantitative gold deportment analysis to demonstrate the efficiency with which gold was recovered during this pilot campaign and then compared to more conventional processing units – centrifugal gravity and conventional flotation.INTRODUCTION Newcrest Mining Limited (NML) has identified that an opportunity exists for improving the recovery of coarse composite particles at its current operations, both as a means for improving overall recovery and as an opportunity for early gangue rejection. As such, Newcrest Mining Limited has taken an interest in the application of pneumatically-assisted, fluidized-bed flotation i.e. ERIEZ HydroFloatTM technology. This interest dates back to 2011 with sighter testwork carried out on their Australian-held ore bodies (Kohmuench et al, 2013). Newcrest continues to assess ERIEZ HydroFloatTM potential for coarse composite recovery and, in the case of the topic of this paper, coarse gold recovery based on examples in the literature which demonstrate the efficiency of this technology in this regard (Carmona Franco et al., (2015); Miller et al., (2016); and Kohmuench et al, 2013)."

Jan 1, 2017

By David Nicholls

?Overview of New Afton ?Reserves and Resources ?Geology and Mineralization ?Exploration ?Capital Project Development to Date ?Mine Development ?Processing ?Construction ?LOM ?Health, Safety, Environment and Social Responsibility Overview of New Afton ?Fully owned by New Gold Inc ?Large gold-copper porphyry deposit, amenable to block cave mining, production commencing in 2012 -1 million ounce gold reserve -1 billion pound copper reserve -Estimated 13 year mine life ?Low operating cost ?Estimated capital expenditure requirements -Spend to date ?US$200million -Remaining to be spent ?US$400milllion ?Robust economics ?Excellent location and infrastructure ?Significant cash flow contributor for the Company

May 1, 2010

By Y. N. Zhang

Friction Stir Welding (F SW) is a novel "green" manufacturing technique due to its energy efficiency and environmental friendliness. This solid-state joining process involves a rotating tool consisting of a shoulder and/or a probe. The shoulder applies a downward pressure to the work-piece surface, constrains the plasticized material around the probe, generates heat through the friction and causes plastic deformation in a relatively thin layer under the bottom surface of the shoulder. The rotating probe mainly drags along, plasticizes, and mixes the adjacent material in the stir zone, creating a joint without fusion. Friction Stir Processing (FSP), a variant of FSW, has been developed to manufacture composites, locally eliminate casting defects, refine microstructure and/or improve the associated mechanical and physical properties including strength, ductility, fatigue, creep, formability and corrosion resistance. However, major challenges such as tool design and wear currently limit the use of F SW/P for manufacturing applications, particularly for high melting temperature or high strength alloys. In this review, the FSW/P tools are briefly summarized in terms of the tool types, shapes, dimensions, materials and wear behaviors.

Jan 1, 2011

By Helge B. Wurst, Michael P. Cipold, Jan F. Bachmann, Claus C. Bachmann

"In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink-float analysis. Time, cost and safety aspects of the sink-float method have prompted the search for a new approach for establishing separation performance criteria, especially as performance levels of separator plants can be maximized if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes readily available. The new method to establish washability and associated performance information utilizes at least two measurement technologies concurrently: single energy x-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy x-ray transmission and image processing. The value of the collected data increases considerably if the washability data were additionally available in time to be considered in the control of the process plant. The incorporation of an automated washability monitor gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested with a range of sample with different densities, varying from 1 g/cm³ (coal) to 5 g/cm³ (iron ore).INTRODUCTIONWashability of minerals like coal and iron ore is expressed by a curve or graph showing the results of a series of float-and-sink tests. Several of these curves are drawn to illustrate different conditions or variables, usually on the same axes, thus presenting the information on one sheet of paper. Washability curves are essential not only for the design but also for the operation of preparation plants.In determining the washability analysis, particle density is the underlying feature of all washability curves. Conventionally, the particles are separated into density fractions by immersing them in fluids of a predetermined density followed by skimming of those particles that stay afloat. The particles remaining afloat thus have a density lower than that of the fluid they were subjected to. The particles that remained at the bottom of the fluid container thus had a higher density higher than that of the fluid. By progressively increasing, for example, the density of the fluid and immersing the remaining particles so as to be able to skim the next density fraction, the particles would be fractionated into density groups. The liquids used range from aqueous solutions to organic liquids to suspensions. Unfortunately the liquids used for this separation process are often toxic and expensive. It stands to reason that a new method of determining washability is sought."

Jan 1, 2016

By K. G. Wheeland, K. G. Byberg

The occurrence of a secondary, dust-fuelled explosion following blasting of sulphide ores has been reported in mines in many countries, including canada, the USA, Australia and South Africa. However there has been little effort to document the events and develop effective control technology. Following a detailed investigation of an incident at the Geco Di vision of Noranda Minerals Inc. , the company held a conference of interested parties in October 1986 to review the state-of-the-art and to agree on action. '!his paper outlines the causes and effects of such explosions, the key conference points and conclusions, and subsequent information-exchange and teclmology-developrnent activities.

May 11, 1988

By D. T. Pritchard

"Introduction""No accounting system is very good, and all of them are infinitely variable*.”The purpose of this chapter is to discuss those facets of a typical accounting system which are most commonly encountered by operating managers in mineral processing plants. However, before concentrating in any detail on these it is important to understand the broad purposes and basic techniques of any accounting system in any major business.The three broad purposes of an Accounting System are:- Administering, controlling, and recording the flow of cash in and out of the business. Cash is, of course, converted into other assets (or stores of value) such as inventory, plant and equipment, etc. These assets also have to be administered, controlled and recorded.- Internal reporting to Management for information, for control, and for use in making business plans and decisions. - External reporting to stockholders, government, lenders and other outside parties.In this chapter we shall organize our discussion of accounting practice in mineral processing plants around these three purposes of accounting and focus in some detail on specific practices and techniques with which operating personnel will be routinely involved. This chapter is divided into the following: Accounting Basics; Administration, Control and Recording of Cash Flows; Internal Reporting; Planning and Budgeting; Cost Control; and External Reporting."

Jan 1, 1989

By Jamie N. Burdeski, Susan E. Hartfield-Wünsch

Aluminum sheet use has been steadily increasing in the automotive industry to achieve mass reduction and improve fuel economy. One significant manufacturing challenge for aluminum sheet implementation is the reduced formability compared to the steel alloys it replaces. This paper includes friction results from the draw bead simulator (DBS), twist compression (TCT) and strip draw (SDT) tests, for two oil based lubricants and four hot melt lubricants. Formability testing was done with the same lubricants and materials, testing in pure stretch with a hemispherical punch, and in draw with a breadpan shaped die.

Jan 1, 2015

By David A. Orava, Richard C. Swider

"The technical knowledge and practical experience accumulated by industry and others in abating acid mine drainage (AMD) is being proactively applied at every phase of the mine life cycle. This paper traces the mine life cycle from exploration to post closure monitoring and maintenance, and reviews AMD abatement measures that have become an integral component of exploration and mining activities.Attention is increasingly being given to evaluating AMD potential as part of exploration work, and studies related to project feasibility and design. Mining, mineral processing, and waste management options are selected taking into consideration their suitability to inhibit AMD. These inhibition measures are typically committed to in closure plans submit-ted at the permitting stage. Mines are operated and decommissioned, often progressively, as planned and in accordance with environ-mental protection policies."

Jan 1, 1996

By J. A. Bos, Z. Dai, P. Quinn, A. Lee

A flowsheet is being developed for processing Thompson ultramafic low-grade nickel ores. This type of ore is characterized by high content of serpentinized magnesium silicates which generate slimes during comminution. Flotation of this type of ore proves difficult due to problems associated with the slimes. The flowsheet, based on extensive laboratory and miniplant flotation tests, consists of two key components: desliming by hydrocyclones prior to flotation and using soda ash for pH control in flotation. Satisfactory metallurgical results have consistently been achieved in laboratory full circuit simulation and miniplant tests.

Jan 1, 2009

By Andreas Zielonka

To meet the increasing demands of the quality and long term stability of technical systems also the applied materials have to full fill higher standards. This is of special importance where the function of a whole system depends on the reliability of the used materials for example for connector systems in automotive, computer and other electronic equipment?s. In most cases for connector systems electro deposited top layers are applied. To improve the quality of the applied layers new electro deposited systems are developed. One important field of research are the development of composite materials as dispersion coatings and multilayer systems. Multilayers are systems with a high number of single inter-layers of different metals or alloys with the wide chance of the alloy composition. As gold is one of the most important contact material for high quality connector systems it is used as basis for the development of multilayer systems. For the electrodeposition of multilayers two different methods can be applied, the single and the dual plating process. As in the dual plating process two different electrolytes are used, the single plating process allows the formation of multilayers from one electrolyte. In the presented research results cobalt and nickel are used besides gold for the formation of the multilayers. The properties of the layers can be influenced in a wide range by the change of electrolyte composition and the process parameters as current density, current waveform, temperature, hydro-dynamic conditions at the electrode surface and by the number and thickness of the inter layers of the deposited materials. The paper describes the fundamentals of the electro deposition of multilayer systems. For the investigation of the properties of the multilayers different techniques are applied. One of the most important parameter are the thickness of the total layer and of the applied sublayers. The thickness of the sublayers can be varied between a few nanometers up to micrometers. The wear resistance, the contact resistance and the plug-in forces are measured as these parameters are important for the technical application of such layers. For the description of the structure composition and surface properties the sample where also investigated by scanning electron microscopy (SEM), energy dispersive x-ray-analyses (EDX) and glow discharge optical spectroscopy (GDOS). The paper shows that the deposition of gold based multilayers is possible and that the properties of such systems can be varied in a wide range what opens new fields of applications of such materials.

Oct 1, 2003

By J. G. Debanne

MOST company-employed petroleum engineers have in their accounting departments punch-card computers that can perform engineering calculations thirty to three hundred times faster than desk calculators, or they can rent such machines from Computing Service centres. These machines not only eliminate the drudgery of desk calculation but also the risks of human errors. The I.B.M. t 604 punch-card computer of Texaco's accounting department in Calgary has been used for oil and gas property evaluations, curve fitting by least squares, statistical core analysis studies, unsteady-state water in-flux studies, phase equilibrium performance prediction of oil reservoirs, gravity segregation calculations, etc.

Jan 1, 1958

By Derek Perkins

"Brenda Mines Ltd. operates an open pit copper and molybdenum mine located in south central British Columbia. The main economic mineralization is chalcopyrite and molybdenite. Pyrite, galena and sphalerite are also present in varying quantities. The mineralization is present in small veins and fractures in a porphyritic quartz diorite host rock.The mill processes approximately 30,000 tonnes of ore daily. The ore is crushed in three stages and then ground in conventional rod mill - ball mill circuits with cyclone classification. The cyclone overflow is fed to the bulk flotation circuit as a pulp with a density of 50% solids. The particle size distribution is approximately 35% plus 65 mesh. Bulk rougher and cleaning flotation produce a concentrate grading approximately 20% copper and 4% molybdenum. This concentrate is fed to the separation circuit, where the copper is depressed with sodium hydrosulphide and the molybdenum is floated. These products are further ground and then upgraded by column flotation. The molybdenum concentrate is pumped to the leach plant to reduce concentration of lead and copper. It is then washed, filtered, dried and packed for shipment to Europe. The copper concentrate is filtered, dried and subsequently shipped to Japan.Prior to November 1977, the mill flotation control was carried out by the assay laboratory using a Philips PW 1540 sequential x-ray spectrograph. The assay set consisted of twelve samples, analysed on a two hourly basis for copper, molybdenum, lead, iron and silica.In order to provide elemental composition information on a much shorter sampling interval and to produce speedier control analysis for automating process control, an Applied Research Laboratories PCXQ on stream analyser was purchased. The installation of this analyser, reduced the turnaround time of the control analyses from (2) hours to (20) minutes. At Brenda, the following assays are used in the mill control strategies."

Jan 1, 1989

By C. J. Clayton, A. J. Haynes, D. A. Hickson, B. Thiele

The Meadowbank Gold Project, formerly owned by Cumberland Resources Ltd. and currently owned by Agnico Mines Ltd., is currently being developed approximately 70 km north of Baker Lake, Nunavut, in the eastern Canadian Arctic region. The Meadowbank Gold Project currently consists of a series of gold-bearing deposits within relatively close proximity to one another, which are planned to be mined primarily as a truck-and-shovel open pit operation using conventional gold milling and extraction. The mining plan indicates that approximately 20 million tonnes of ore will be mined over a mine life of eight to ten years. The operation will generate approximately 160 million tonnes of mine waste rock and about 20 million tonnes of tailings. The site is located in an area of continuous permafrost with mean annual average air temperature of -11°C and average annual precipitation in the range of 100 to 200 mm. Lakes cover a large portion of the site, including some of the ore deposits. The location of the site and the physical environment pose challenges to development. This paper presents some of the designs considered to effectively manage and utilize the waste products of mining at the project. Note that volumes, tonnages, construction concepts, and data presented in this paper are accurate for the time of writing and are subject to change and modification as the project progresses, additional modelling is carried out, and additional data are obtained.

Jan 1, 2007

By G. R. Webber

CHEMICAL AN AL YSIS by x-ray emission spectrometry has become increasingly important during the past few years. The method is analogous to optical spectrography ?with x-rays being used instead of light and should not be confused with methods of x-ray diffraction used? for identification of minerals and chemical compounds. X-ray emission spectrometry has many advantages for both qualitative and quantitative analysis. Its optimum concentration range is higher than that of the optical spectrograph, and the group of elements which can be detected is not identical to that which can be detected by the optical spectrograph. Elements which can be detected by the x-ray spectrometer are those elements from magnesium (atomic number 12) to uranium (atomic number 92) in the periodic table. The lightest elements in this range have low sensitivities and more specialized equipment is necessary for their detection than for the heavier elements. A large number of applications of x-ray analysis have been directed toward the analysis of ores, metallurgical products, and related materials (see References at end of paper). A more complete bibliography is presented in the Norelco Reporter, Vol. 3, 1956, pp. 37-39. The periodicals Analytical Chemistry and Applied Spectroscopy are a good source of current articles and references.

Jan 1, 1957