Search Documents

By J R. O Walli

Large production shafts can be successfully sunk through the ubiquitous Blairmore formation of southern Saskatchewan by employing the freezing process and by the installation of a cast iron tubbing lining. Although the freezing technique for shaft sinking and the use of cast iron tubbing to preserve the shaft are new to the North American continent, these procedures have been employed in Europe for the past eighty years. More than 200 shafts, covering a wide variety of ground conditions, have been sunk by the freezing process, and most of these have been lined with cast iron tubbing. The No. 1 shaft of International Minerals and Chemical Corporation, near Esterhazy, Saskatchewan, comprises the first major example in Canada of the employment of European methods to overcome extremely difficult ground conditions. The Blairmore formation was solidified by the deep freezing process, employing a lithium chloride solution as the refrigerant, with input temperatures ranging to -55°F

Jan 1, 1964

By J. R. Gill

Introduction The property and plant of the Falconbridge Nickel Mines, Limited, is situated about 13 miles northeast from Sudbury, in Falconbridge township, near the eastern extremity of the southern Nickel Range. As early as 1899 or 1900 some work was clone on this property by the late Thos. A. Edison, when a shaft was sunk through 80 feet of overburden to within a few feet of the ore-body. At this point quicksand was encountered, which made it impossible to continue with the equipment at hand. As a result, the activities of the Edison party ceased in this section. There was no further progress until 1915 and 1916, when an extensive diamond-drilling campaign, carried out by the E. J. Longyear Company, located the ore-body that is now being worked. The property was acquired by the present operators in 1928, and in September of that year active mining development was commenced. Features Influencing Design Of Plant Early in 1929 plans were prepared for a smelter and the necessary crushing and sorting plant. In spite of the general trend towards the reverberatory furnace as a smelting unit, it was decided to erect a blast-furnace plant. The limited tonnage to be treated, of course, influenced this decision to a great extent. However, it was known that, with the proper procedure, extremely favourable results, both economic and metallurgical, could be obtained in blast furnace smelting. The possibility of very low slag losses, the simplicity of operation by the elimination of roasting plant, fuel plant, etc., the ability to handle coarse feed, and the lower initial cost, were considered factors in favour of the blast furnace. Notwithstanding the fact that we might be called on to treat a certain amount of concentrate, it appeared that the blast furnace was the proper unit for the contemplated operation.

Jan 1, 1932

By C Kumar

Scaffolds are temporary structures built to facilitate construction activities on site. A considerable amount of resources are allocated to scaffolding on industrial projects. Variability in geometrical features and space accessibility of structures on industrial projects, in addition to involvement of different trades that share the use of scaffolds, requires an extensive understanding of scaffolding requirements. Hence, it?s important to plan and estimate scaffolding man-hour requirements for the different construction areas on an industrial site. Contributing factors involved in such estimates include the list of trades that work in a construction area, trade working hours, volume of work, geometry of equipment erected, etc. A simulation template for predicting scaffold erection man-hour values for individual construction areas in an industrial project was developed in Simphony 4.0. The template is based on mapping the geometry of equipment and other factors to man-hours of scaffold work. The template facilitates the use of distributions as inputs and produces a range estimate of scaffold man-hours. The mapping is based on a linear regression model derived from existing project data from PCL Industrial Management Inc. The template is being further developed to incorporate the ability to predict scaffold erection schedule and material requirements based on construction work areas or equipment lists of an industrial construction project.

Aug 1, 2013

By Q. H. Bui

The elastoplastic self-consistent model is one of the effective models to study the initial microstructure effect on the mechanical behavior of bulk materials. However, the use of this micromechanics-based model which takes into account only the Hall-Petch relationship at grain level for predicting the grain sized effects on the strength of the deformed materials is not accurate yet because of the fact that the dislocation density contributes also to the strengthening of this kind of materials. In this study, a modification made to the Hill-Hutchinson elastoplastic self-consistent model was proposed for investigating the microstructure dependence of the mechanical behavior of cold-drawn 6063 aluminium tubes. Because of the novel modification, an estimation procedure with two steps was required to identify the parameters of this micromechanical model. An acceptable agreement between experimental and theoretical stress-strain curves was achieved.

Jan 1, 2011

By B. F. Haanel

IN the fall of 1929, a paper was presented at the Annual Western Meeting of the Institute entitled The Fuel Research Laboratories at Ottawa and the Scope of Their Investigations. At that time, the equipment of the laboratories had not been completely installed, but the regular routine work was being carried on as usual, and several large-scale investigations were being conducted. It is now five years since that paper was presented, and it seems fitting that a brief description of the investigations which have been undertaken, together with results-especially those which have reference to western Canadian fuels-be presented at this Annual Western Meeting. The coal mining industry of western Canada has, within the past few years, suffered many unfortunate vicissitudes. The replacement of coals by oil, for bunkering ships, for operating railway locomotives, and for heating, has weighed heavily on the coal mining industry of British Columbia and Alberta generally, but more particularly in the Crowsnest Pass area and Vancouver-and hydro-electric developments have also left their impress. With a full appreciation of these conditions, the Department of Mines planned research and large-scale investigations which it was considered would be of the greatest benefit to the coal industry, and the results have amply justified the plans and anticipations. The fact, however, must not be lost sight of, that the application of the findings of certain of these investigations would not have been feasible had not the Federal Government assisted the transportation of coal by the application of railway subventions. These subventions permitted Canadian coals to compete at competitive points with United States coals, and it must be admitted also in this connection that certain of the collieries which have benefitted, both as a result of the railway subventions and the investigations conducted by the Fuel Research Laboratories of the Department of Mines, made special efforts to produce a coal which was capable of competing with the American product, by special preparation at the mines.

Jan 1, 1936

By R. B. Allen, B. S. W. Buffam

"The property of Chesterville Mines, Limited, is in McGarry township, Timiskaming district, Ontario, about 25 miles east of Kirkland Lake. It consists of a group of fifteen claims that extend northeast from the KerrAddison mine for a distance of 2 miles.In June, 1906, two groups of prospectors left the town of Chesterville, Ontario, to prospect in northern Ontario. Silver had been discovered 3 years before at Cobalt and the large profits of this young mining camp were the principal incentive to extending the field of exploration northward. One group consisted of Dr. Reddick, Edward Flynn, John Hummel, William Knott, and Colin Cameron. The other group comprised J. T. Kearns, Herman Hummel, W. G. Barkley, and J. Elliott.The two groups travelled north by train to Haileybury and thence to Larder lake by canoe. Camps were pitched on the northeast arm of the lake, and within a short time a discovery was made by Edward Flynn of the first party, who found gold on the property now owned by Kerr-Addison Gold Mines, Limited. Herman Hummel and J. T. Kearns shortly afterwards made the second discovery, on what is now the Chesterville property. These discoveries, made some years prior to those at Porcupine and Kirkland Lake, are believed to be the first in that part of northern Ontario.The Hummel-Kearns claims were incorporated in the following year under the name of Chesterville Larder Lake Gold Mining Company, Limited. It was not, however, until 30 years later, in 1936, following the increased premium on gold, that sufficient capital was placed in the treasury of the Company to carry out an extensive diamond drilling programme. This exploratory drilling was started early in 1937 under the direction of Leo. J. Kearns, and a large body of ore was intersected in the first drill hole. Underground work was started in 1938, a mill was built, and the first gold brick was poured on July 29th, 1939."

Jan 1, 1954

By B. Voyzelle

The deterioration of highway and bridge infrastructure has received considerable attention in recent years because of the billions of dollars needed for repair and rehabilitation. A major factor contributing to this problem is the corrosion of steel reinforcement. Reinforcing steels with good corrosion resistance and relatively low price are therefore essential for maintenance, cost reduction and service-life extension of the steel-reinforced structures. This article describes the development of low-alloying steels that offers good corrosion resistance with reasonably low cost. Topics include steel microstructures, mechanical properties, corrosion performance, industrial applications and economic aspects.

Jan 1, 2005

By James A. Robertson

"The Pronto Mine located at the east end of Lake Lauzon, Long Township, some 12 miles east of Blind River is of historic note being the discovery locality and the first producing mine of the Elliot Lake uranium camp. Radioactive bedrock was discovered in 1949, a commercial deposit was verified in 1953 and production commenced in 1955. Production continued to April 1960: total tons milled 2,264,404 from which 4,643,835 pounds U,O, were recovered at a recovered grade of 2.05 pounds U3O8 per short ton.The orebody is in a bed of pyritic quartz pebble conglomerate at the base of the Matinenda Formation of the Elliot Lake Group of the Huronian Supergroup. The rocks strike east and dip 15 degrees to 20 degrees south and unconformably overlie Early Precambrian granite, the upper surface of which is marked by a regolith. Several diabase dykes cut the orebody which is also affected by albite, chlorite, and carbonate-rich alterations. To the south the orebody is cut by a fault. The orebody is 6to 10 feet but locally 10 to 15 feet thick, has a strike length of 3,500 feet and extends down dip for 3,600 feet to a depth of 1,000feet. Some 300,000 tons of ore grade mineralization remain in the deeper portion of the mine.IntroductionThe Pronto Mine, (Photo I) at the east end of Lake Lauzon in Long Township some 12 miles east of Blind River, is of particular interest as being the discovery site and the first producing mine of the Elliot Lake camp.Production at the Pronto Mine commenced in 1955 and continued until 1960 when the mill was converted to treat copper ore from the nearby Pater Mine at Spragge. A description of both mines, based on material provided by the mine staff, was given in the report on ""Geology of the Spragge Area"" (Robertson, 1970).As little study has been done on Pronto geology or petrology since mine closure, the earlier description of exploration and geology is essentially repeated, but shortened, here- the main change being that the stratigraphic terminology has been amended as recommended by the Federal-Provincial Committee on Huronian Stratigraphy (Robertson et al., 1969)."

Jan 1, 1986

By K. H. Kretzschmar, M. A. Smith

A brief review of the rapid growth of ACT in Western Canada is presented. It is remarked that this rap-id growth has been accompanied by a heterogeneous approach to design. A more rational and consistent approach is suggested, together with the assumptions on which this approach is based. The operating history of some existing installations is discussed briefly, and conditions necessary for the continued growth of ACT are outlined.

Jan 1, 1960

By D. Beneteau, D. Milne

"Advances in technology provide educators with valuable tools to enhance their teaching and efficiently deliver content to larger audiences. University educators are often encouraged to become more “research intensive” and to increase student enrollment. Faced with these pressures, there is a tendency to use technology to improve teaching efficiencies rather than to enhance existing teaching approaches. Practical learning in applied engineering courses would suffer greatly if hands-on experience is not emphasized. This paper discusses advantages and limitations of new technologies applied to learning, and methods to incorporate more hands-on experiential teaching techniques to applied mining engineering courses.RÉSUMÉ Les avancées technologiques fournissent aux éducateurs des outils intéressants pour rehausser leur enseignement et livrer efficacement de la matière à de grands auditoires. Les éducateurs universitaires sont souvent encouragés à devenir plus « axés sur la recherche » et d’augmenter l’inscription d’étudiants. Face à ces pressions, il y a une tendance à utiliser la technologie pour améliorer l’efficacité d’enseignement plutôt que de rehausser les approches existantes d’enseignement. L’apprentissage concret dans les cours d’ingénierie appliquée souffrirait grandement si l’accent n’est pas mis sur l’expérience pratique. Le présent article discute des avantages et des limitations des nouvelles technologies appliquées à l’apprentissage et des méthodes pour incorporer plus de techniques expérimentales pratiques aux cours de génie minier appliqué."

Jan 1, 2016

Agenda ? Introduction ? Inmet?s Operations and Closed Properties ? Inmet?s SECA Philosophy ? Inmet?s SECA Framework ? The Business Case for TSM ? Inmet?s TSM Reporting ? Inmet?s 2004 TSM Performance ? Opportunities for Improvement ? What Have We Learned From The TSM Process So Far? ? Summary Introduction ? Inmet has evolved into a strong TSM supporter ? Inmet is confident that TSM can be successfully and cost effectively implemented by smaller companies ? Inmet?s reporting on economic, environmental and social performance was raised significantly in our 2003 Annual Report ? a signal our commitment to good performance and improvement in these areas ? Our 2004 Annual Report has been further enhanced with the inclusion of our TSM performance

Apr 1, 2005

By Thomas J. Ferree

"There has been a major evolution of mineral processing technology in the past decade. The evolution has been driven by recognition of broad environmental changes which have impacted various areas of the world. Numerous government regulations have required many mining and mineral processing organizations to introduce changes to reduce the undesirable effects on the environment; many mining companies have voluntarily introduced new technologies and practices which surpass the limits imposed by the regulations. Surprisingly, some of the 'new' technologies are modifications of concepts developed decades earlier. Gravity separation technology is in this category.Mineral Deposits Limited, an Australian company, has been a world leader in the development of mining concepts, reclamation practices and equipment technology that is environmentally suited to today's requirements. This paper relates to equipment used for gravity concentration and electrostatic separation systems, including Reichert cones, spirals, and electrostatic separators. The basic devices and technologies were developed more than forty-five years ago, but use of the systems was quite limited until environmental and conservation practices were recognized and introduced. Spiral concentrators, for example, were patented in the mid-l940s by I.B. Humphreys in Denver , Colorado. The two types of spirals marketed (the Model 24A for minerals and the Model 24C for coal) remained essentially unchanged until expiration of the patents. During this early period most spirals were used in iron-ore wash plants on the Mesabi Range to recover fine iron which previously had been discarded. About the same time sand mining plants in Florida incorporated spirals to recover titanium minerals and zircon from lowgrade beach sands. The Labrador Trough opened new opportunities for spirals when hard-rock iron-ore deposits were developed; approximately 10 000 Model 24A Humphreys spirals were installed between 1958 and 1966. About 5000 spirals of this model are still operating in the same capacity, in spite of the fact that extensive improvements have since been made in gravity separation technology."

Jan 1, 1993

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallisation and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. In an expansion or a new project, a large component of the capital cost can be associated with the pressure leach step and process engineers frequently look for opportunities to mitigate costs. This paper examines a new route for increasing the capacity of an exothermic pressure oxidation leach for sulphide concentrates, sulphide and phosphide mattes and alloys.

Jan 1, 2004

By Staff

Introduction The Hedley mine, perhaps better known as- the Nickel Plate mine, is one of the outstanding properties of southern British Columbia. Discovered in 1898 by Woollison and Arundell, prospectors, the property was bonded in 1899 to M. K. Rodgers for the Marcus Daly Estate, of Butte, and development was started the same year. From the high grade of the ore outcrop, and its colour, due to oxidation of the arsenopyrite, it was not difficult to open up and trace the showing. The Nickel Plate ore-shoot, which apparently had been easy to follow on surface, was more difficult to trace underground. In 1903, prospecting on an adjoining property, the Sunnyside, showed commercial ore at surface, but it was only after two years' work that the ore-body was defined and shipments started. From this property, $1,200,000 have been taken out. Prospecting was also carried on on the IXL, Climax, Copper Cliff, Mound, Bulldog, Exchange, Silver Plate, Gold Plate, and other properties, all of which had surface showings, but up to date only the Nickel Plate, Iron Duke, Morning, and Sunnyside have produced commercial ore. In 1904, the Bulldog looked like a very promising mine, but it failed to make good. In 1905, the Sunnyside No. 1 was in the limelight, but it also failed to make the grade. In 1906, an outcrop on the Sunnyside No. 3 looked interesting. Subsequent work. on this claim produced $840,000, and at the same time ore which yielded $400,000 was mined from the Sunnyside No. 4. In 1908, the Nickel Plate ore-body entered a lean zone and, as the diamond drill failed to give satisfactory results, the Daly Estate, after making a profit of $1,151,000, sold the property to the Hedley Gold Mining Company, Limited, for $760,000, retaining, however, a large interest.

Jan 1, 1929

By C. P. Jenney

"Exploration for copper, in a region of 7,000 square miles on the Arctic coast between longitudes 114 and 118 degrees west, has covered a period of nearly 200 years. Occurrences of native copper, used by the natives for tools and weapons, have been reported since the early part of the eighteenth century. In J 771 Samuel Hearne of the Hudson's Bay Company, in the course of his classic 3-year journey from Fort Churchill, became the first white man to see the deposits, and incidentally the first to reach the Canadian Arctic coast by land. During the next 140 years the deposits were mentioned by every explorer and traveller who passed through the area. A good historical summary of this literature has been presented by Tyrrell (1912).In 1911-12 the Douglas-Sandberg party did the first geological mapping along the Coppermine River and Dismal Lakes (Douglas, J., 1913; Douglas, G. M., 1914), and described the copper occurrences there. In 1914 J. J. O'Neill (1924) of the Canadian Arctic Expedition investigated the showings on Bathurst Inlet. In 1929-31 two Canadian exploration companies sent prospectors and geologists to the area (Gilbert, 1931; Norrie, 1931; Duncan, 1931). Since that time only brief references have been published (Kidd, 1931; Stockwell and Kidd, 1931; Lord, 1941, 1951; Washburn, 1947). In 1943-45 an area of more than 1,500 square miles was prospected by American Metal Co. of Canada, Ltd., under the direction of the writer. Forty-nine showings were examined; seven of these were mapped in detail by plane-table and two were sampled by 27 short diamond drill holes totalling 3,061 feet. All holes were in permanently frozen rock, and the deepest vertical distance reached was 206 feet. Five groups of claims were staked. These later lapsed, but one of the groups was restaked in 1951, and assessment drilling and some trenching were carried out in 1952-53. Results were disappointing, and the claims have been allowed to lapse.The area is within the Arctic Circle, northeast of Great Bear Lake and 360 miles north of Yellowknife on Great Slave Lake. For exploration purposes, access is by aircraft from Yellowknife. During the short open season heavy freight can be brought by sea to Coppermine at the mouth of the river, either from Aklavik at the mouth of the Mackenzie or around Alaska. Concentrates would have to be moved by these routes.Although none of the deposits so far found is mineable under present conditions, the total volume of copper in the numerous showings marks the district as a major area of copper mineralization, which may some day be of economic importance."

Jan 1, 1949

By Andrea Lisjak Bradley

Clay shales are currently being assessed as possible host rock formations for the deep geological disposal of radioactive waste. However, one main concern is that the favourable long-term isolation properties of the intact rock mass could be negatively affected by the formation of an excavation damaged zone (EDZ) around the underground openings. The goal of this thesis was to develop and validate a mechanically-based model of the deformation and failure process of a clay shale, namely Opalinus Clay (OPA), with particular focus on the influence of anisotropy on the short-term response of circular tunnels. To achieve this goal, a hybrid continuum-discontinuum numerical approach was developed in combination with new field measurements from the Mont Terri underground research laboratory. The response of OPA during the excavation of a full-scale emplacement (FE) test tunnel was characterized by geodetic monitoring of wall displacements, radial extensometers and longitudinal inclinometers. The deformation measurements indicated strong directionality induced by the combined effect of in-situ stress field and bedding planes striking parallel to the tunnel axis, with the most severe deformation occurring in the direction approximately perpendicular to the material layering. Computer simulations were conducted using a newly-extended combined finite-discrete element method (FEM/DEM), a numerical technique which allows the explicit simulation of brittle fracturing and associated seismicity. The numerical experimentation firstly focused on the laboratory-scale analysis of failure processes (e.g., acoustic activity) in brittle rocks, and on the role of strength and modulus anisotropy in the failure behaviour of OPA in tension and compression. The fracturing behaviour of unsupported circular excavations in laminated rock masses was then analyzed under different in-situ stress conditions. Lastly, the proposed modelling methodology was applied to the aforementioned FE tunnel to obtain unique insights into the EDZ formation process around emplacement tunnels for nuclear waste. The calibrated numerical model suggested delamination along bedding planes and subsequent extensional fracturing as key mechanisms of the damage process potentially leading to buckling and spalling phenomena. Overall, the research findings are already having a direct impact on the preliminary design process of an underground repository for nuclear waste in Switzerland.

Jan 1, 2015

By Daniel Lachapelle, Nuri Hmidi, Turgut Yalcin

"Simulation can serve as a convenient tool in studying the behaviour and performance of grinding circuits by facilitating the evaluation of various scenarios and identification of optimum operating conditions. This technique was applied to the St Andrew Goldfields Ltd.’s Stock Mine Mill which is a 1300 tpd gold milling facility, offering custom milling services as well as processing the Company’s own ores. Lack of adequate instrumentation in the mill poses a challenge in attaining optimum performance especially with changing ore types and characteristics. The grinding process is monitored essentially by manual measurement and adjustment of pulp densities at various streams. A simulation program was designed to assist in the effective implementation of this mode of grinding control. Product sizes from both the primary and secondary grinding circuits were correlated empirically to relevant process variables using a database formed from the results of past sampling campaigns. The simulator was created in Microsoft Excel whose data analysis and optimization tools coupled with its Visual Basic Programming capabilities were found to provide an excellent environment for the development of a cost-effective, efficient and user-friendly simulation program.INTRODUCTIONGrinding is often a very costly unit process in milling operations, mainly due to the excessive energy consumption associated with it. For example, for a Canadian copper-zinc flotation mill, grinding was listed as being the most costly item taking up 30.4% of the total milling expenses, followed by the flotation cost at 2 1 .O% (Kidd Creek Mines Ltd., 1982). A survey on 45 copper flotation mills around the world showed the average grinding cost to be 34.5% of the total milling cost (Weiss, 1985).Overgrinding aggravates the cost issue, while insufficient grinding either causes loss of valuable minerals to tails or results in low-grade concentrates. Therefore, it is essential that grinding circuits be carefully controlled and monitored. To this end, a great deal of effort has been devoted over the years to the modelling and simulation of grinding systems in order to assist in the efficient running of these processes."

Jan 1, 2001

By M. W. Bartley

DURING the field season of 1938, the Ontario Department of Mines assigned a combined geological and geophysical survey patty to the investigation of the location, genesis, structural relationships, and economic possibilities of the hematite deposits at Steeprock lake. The investigation was carried out by detailed mapping of the rock exposures and a magneto-metric survey of the drift-covered portions of the area. This was supplemented during the winter of 1938-39 by further geophysical work conducted on the ice. Dr. A. A. Brant, of the Department of Physics, University of Toronto, was in charge of the geophysical work for the Department of Mines in the summer and for the Sterola Exploration Company in the winter. The writer supervised the geological examination. Scope of the Paper The present paper is an attempt to acquaint the members of the Institute with the structure and mode of occurrence of the deposits, since many people are of the erroneous opinion that they are analogous to the Mesaba and Michigan deposits. It is hoped that, from this discussion, they may be able to draw some conclusions of their own regarding the nature of the deposits, and the importance and future possibilities of the region.

Jan 1, 1939

By Ming’an Wei, Qifu Duan, Chengtie Wang, Jianmin Wu, Erdenet Mining Corporation, Lusheng Zhou, Wenjian Wu

"The development and industrial applications of magnetic liners have been around for decades. A Swedish company SKEGA first introduced the rubber magnetic liner, and then followed by the Chinese metal magnetic liners. Traditionally, both liners were used in secondary and regrind ball mills, especially for ores containing magnetic materials. Mostly steel balls or equivalent forged balls, usually below 60 mm in diameter, were used as grinding media. With the development of mineral resources over the years, SAG mills and larger ball mills have become the dominating components for comminution circuit design globally. Due to the larger ball mills and thus larger grinding balls (up to 80 mm) especially in non-ferrous metal industry, the application of magnetic liners has been very limited. Based on the new development of materials, the HMR Group Limited has been exploring new designs of magnetic liners which led to the invention of the Nano Steel Magnetic Liner (NSML). Recently, NSML had a successful application in a 5.5m x 6.5m ball mill with 80 mm balls at the Erdenet Copper Mine in Mongolia. Although the first set of liner had a service life of 12 months, the design of the second set was modified and improved to accommodate the operating conditions, which is expected to reach least 24 months service life. The original manganese steel liner only had about 8 months liner life.1. IntroductionMineral processing is an essential operation for the development and utilization of mineral resources. The effective concentration of various useful minerals depends on sufficient liberation of the mineral particles in the ore. The crushing and grinding process such as ball milling are the most common way to achieve proper liberation size. Mill liner is an eternal topic for the operations, not only because it protects the equipment, but also affects the mill grinding efficiency and availability. In recent years, magnetic mill liners have been developed that can easily meet the production targets with numerous benefits, such as zero maintenance, reducing specific energy consumption and improving grinding efficiency."

Jan 1, 2016

By E. Wusaty

"Fording Coal is a wholly owned subsidiary of Canadian Pacific Limited. The company was founded in 1968 to mine metallurgical coalfor export at the Fording River operations in southeast British Columbia.Today, Fording Coal Limited also operates the Whitewood mine under contract to TransAlta Utilities and the Genesee mine under a joint venture arrangement with Edmonton Power. Both these operations are located just west of Edmonton and produce subbituminous low-sulphur coal which is used for power generation. Fording also owns and operates two industrial mineral mines in the United States and is mining overburden under a lo-year contract with Syncrude Canada at Fort McMurray.As of December 1992, Fording Coal Limited owns and operates the Greenhills mine which was closed due to bankruptcy. This papers deals with the innovations and changes which have been made and those which are currently being implemented to make this operation competitive in the world export coal market. IntroductionOn December 4, 1992, following a tendering process, Fording Coal was awarded 80% controlling interest in the Greenhills mine by Trustee Arthur Andersen Inc. Assets acquired included 100010 of the land and coal leases and 80% of the major joint venture assets including all structures. The remaining 20% is owned by Pohang Steel Canada Ltd., a wholly owned subsidiary of Pohang Iron Steel Co. of Korea. The Greenhills mine had been in continuous operation since 1983 and was finally closed due to bankruptcy of its majority owner on October 31, 1992.A permit to operate the Greenhills mine was issued by the British Columbia government on January 29, 1993, and Fording Coal Limited started mining operations in late February 1993.To return the Greenhills mine to profitability significant changes were required in workforce productivity, mining methods and equipment selection. These mine plan changes are designed to make the Greenhills operation competitive in world markets, provide longterm employment for the company's workforce and ensure that a secure supply of coal is available."

Jan 1, 1994