Search Documents

By C. W. Hancher, B. D. Patton, W. W. Pitt

"There are a number of nitrate-containing wastewater sources, as concentrated as 30 wt % NO3 and as large as 2000 m3/day, in the nuclear fuel cycle. The biological reduction of nitrate in waste water to gaseous nitrogen, accompanied by the oxidation of a nutrient carbon source to gaseous carbon dioxide, is an ecologically sound and cost-effective method of nitrate waste disposal. These nitrate-containing wastewater sources can be successfully biologically denitrified to meet discharge standards in the range of 10 to 20 g N(NO3-)/m3 by the use of a fluidized bed bioreactor. The denitrification bacteria are a mixed culture derived from garden soil; the major strain is Pseudomonas. In the fluidized-bed bioreactor, the bacteria are allowed to attach to 0.25- to 0.50-mm-diam. coal fluidization particles, which are then fluidized by the upward flow of influent wastewater. Maintaining the bacteria-to-coal weight ratio at approximately 1:10 results in a bioreactor bacteria loading of greater than 20,000 g/m3,This paper describes the results of a bio denitrification R&D program based on the use of fluidized bioreactors capable of operating at nitrate levels of up to 7000 g/m3 and achieving denitrification rates as high as 80 g N(N03-) per day per litre of empty bioreactor volume. IntroductionThe discharge of wastewater containing nitrate at concentrations greater than stipulated by the Environmental Protection Agency (EPA) creates an environmental hazard and constitutes a civil and/ or criminal legal liability.(I.2) At present, we have three options: (1) recycle and reuse of nitrate streams the total economic and technical balance should be Closely examined; (2) use of an alternative acid, which may pose an entirely different set of problems ; or (3) disposal of nonreusable nitrate sources by an environmentally acceptable procedure."

Jan 1, 1980

By C. J. Cattarello

"The Langmuir Mine is located seventeen miles south-east of South Porcupine in Langmuir Township.The property was developed as a Joint Venture between Noranda Mines Limited and the International Nickel Company of Canada with Noranda responsible for the operation of the property.The Mine came into production in June 1973 at a rate of 700 tons per day of nickel ore.MINING The mining method selected for the Langmuir Project was a sub-level retreat method. This consisted of driving sub-levels longitudinally in the ore body at 35 foot, intervals with the sub-levels being connected by a ramp from each main level for the use of trackless mining equipment.GENERAL GEOLOGY OF THE LANGMUIR MINE The deposit is situated about 1,000 feet west of the shore of Carmen Bay at the south of Nighthawk Lake in Langmuir Township. The area is underlain by andesite and rhyolite flows with iron formations which are intruded by gabbro, diorite, peridotite and late precambrian diabase dikes."

Jan 1, 1975

By Dwayne D. Tannant

The Fox Pit at EKATI Diamond Mine reached a depth of approximately 150 m as of September 2005. The pit is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high bench faces. A series of blasting tests were conducted to improve catch bench reliability and increase the percentage of benches that meet an 11 m catch width. The design changes focussed on reducing damage to the bench crest because maintaining the bench crests is the most important factor in achieving good bench reliability. The most significant improvement was obtained by raising the bottoms of the lower trim blastholes by 0.5 m. This change decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. Another improvement was the use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast. This change reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest. As mining and the blast testing progressed, the portion of the bench with crest achievements (>11 m) increased from 57% to 75%.

May 1, 2006

By E. Kouame, M. D. Everell, D. Hodouin, T. Kasongo

"To properly operate a mineral beneficiation plant it is often necessary to have systematic evaluations of the performances of a piece of machinery, of one of the processes or of the plant as a whole. The state of a process can be described from a collection of data: flow-rate values, particle-size distributions and chemical compositions of the various streams of the circuit studied.However, the obtained raw data are generally redundant and inconsistent from a material balance viewpoint, due to natural disturbances, sampling errors, unreliable instrument readouts and laboratory analysis inaccuracies.BILMAT is a computer program which upgrades mineral processing data, adjusting them in a least-squares sense in order that they may verify material conservation constraints. As a consequence, the program is able to calculate the best values of unmeasured flow rates (such as. circulating load ratios). BILMAT is a very general program in the sense that it can accept various data from any type of mineral processing circuit, and its usefulness is demonstrated here for three processing circuits of a pyrochlore concentration plant: grinding, desliming and flotation.IntroductionComputation of the material balance around any metallurgical process, that is the determination of stream flow rates and composition. is a basic step in its evaluation. In spite of the simplicity of the physical laws of mass conservation. and of the very fundamental need to know the flow of components around a process. it appears, particularly in mineral processing. that material balancing is quite often a difficult task. The reasons for this involve the problems associated with collecting measurements in mineral dressing plants. They are generally poorly instrumented and invariably data must be collected through hand sampling. Due to the heterogeneous nature of the streams, segregation occurs and samples are often not adequately representative, a problem made worse by the lack of circuit sampling facilities, which are often completely ignored by plant designers. Furthermore, the nature of the measurements to be performed (for instance particle size distributions in the fine range) frequently gives inaccurate results."

Jan 1, 1981

By S. Avalos, J. M. Ortiz, W. Kracht

Semi-autogenous grinding mills are intensive energy consumers. Current models base their energy consumption inference on operational variables and feeding ore characterization. While they provide adequate design guidelines, they are not suitable for real-time energy forecasting dealing with gaps in operational dataset and up/downstream process bottlenecks. This work explores the capability of Gated Recurrent Units to learn the semi-autogenous grinding mill consumption behaviour. Gated Recurrent Units are trained to forecast different time-support consumptions under a time-series operational dataset. The results show high performance on small supports (30 minutes) to capture local variability and long-trends while larger time supports (8 hours) can only capture time-trends but not local variability. The proposed technique seems promising for further research and implementation on real mine cases since the input variables are low-cost and easy to obtain. INTRODUCTION Current changes in the Chilean energy matrix (Román-Collado, Ordoñez, & Mundaca, 2018), from fossil fuels to renewable energies, have impacted different industries and particularly the mining sector. Solar energy incorporation into greenfield/brownfield projects will help reducing costs and will lead to rethink foundational paradigms (production and processing strategies) (Pamparana et al., 2017). Also, integration of new space-time predicting tools together with automated real-time updating models are some of the main challenges in the geometallurgical framework (Ortiz et al., 2015; van den Boogaart & Tolosana-Delgado, 2018). Those contexts encourage and demand the development of tools capable of predicting the energy consumed by mining systems, being comminution the greatest energy consumer with an average close to 50% of the entire mine consumption (Cochilco, 2013). In comminution, the semi-autogenous grinding mill (SAG) represents the largest energy consumer (~10 nominal each SAG). Theoretical and empirical energy consumption models (Jnr & Morrell, 1995; Morrell, 2004; Silva & Casali, 2015) base their inferences mainly on feed/product size distributions, SAG sizing, bearing pressure, feed hardness, water addition and grinding charge level, and commonly assume steady-state and work isolated from up and downstream processes. While those techniques provide adequate design guidelines, they are not suitable to predict hourly, daily or even weekly energy consumptions on interconnected comminution circuits where upstream/downstream bottlenecks lead SAGs to operate below designed regimes. Forecasting energy consumption is required by short-term energy management, medium and long-term planning energy consumption, designing the nominal capacity of renewable energy sources, among other. Also, when models are input-sensitive and some of those input measurements are expensive and/or time consuming, model robustness suffers when real-time predictions are required.

Jan 1, 2019

By V. G. Papangelakis, G. A. Moldoveanu

"One of the major commercially viable secondary sources of rare earths elements (REE) are the ion-adsorption ores, containing 0.05-0.3 wt% rare earth oxides physically adsorbed on the surface of clay minerals formed during weathering of lanthanide-rich rocks. Although ion-adsorption deposits are substantially lower grade than other types of rare earth sources, this is offset by the easier mining and processing costs and the low content of radioactive elements. The conventional extraction route involves ion exchange leaching with monovalent cation solutions (usually ammonium sulphate) under ambient conditions; during the process, the lanthanides are desorbed and transferred into solution, being replaced by the exchange cation. While ammonium ions are known to perform best, there is increased environmental motivation to investigate alternative lixiviants in order to minimize ammonium sulphate impact via reducing its use without considerable loss in rare earth recovery.The objective of the present research was to screen various cations salts (alkaline and alkalineearth metals present as sulphates, chlorides and acetates, respectively) in order to comparatively evaluate lanthanide desorption levels and provide a theoretical base of the observed behaviour. The overall aim is to gain a better understanding of how both cation and anion may affect the overall REE recovery from ores in order to provide alternative processing routes. The distinct exchange capabilities of cations were explained in terms of differences in cation hydration enthalpy within the same group, i.e. Cs+ > NH4 + > K+ > Na+ > Li+ and Ba2+ > Ca2+ > Mg2+. For the same cation, it was determined that REE extraction efficiency follows the order sulphate > acetate > chloride, based on dissimilarities in constants of formation values. Various process implications scenarios will be described based on using mixed cations and anion matrices."

Jan 1, 2016

By John C. Loretto

"The paper identifies two of the main problems encountered in recent hydrometallurgical plants for the recovery of gold and silver: firstly, the plant recovery is lower than anticipated from the testwork; secondly, the metallurgical accounting figures cannot be reconciled.The principal reasons for the plant recovery being lower than the testwork are discussed, together with solutions that can minimize these problems both during the design stage and during the plant operation after the problems have manifest themselves.The reasons for the difficulties in metallurgical accounting are analyzed by reviewing the various components of the plant figures. Recommended solutions are given for minimizing this problem and the realities of obtaining accurate figures are discussed.IntroductionThe start-up over the last few years of new hydrometallurgical plants for the recovery of gold and silver has brought to the surface again a number of problems. Most of the problems have existed for some time and they manifest themselves mainly in two ways. Firstly, the plant results do not agree with the metallurgical testwork figures; secondly, the metallurgical accounting figures do not balance.Metallurgical TestworkThe plant results not agreeing with testwork figures are mainly due to:a) testwork samples not representative of the eventual plant feed;b) misinterpretation or misunderstanding of testwork ;c) plant losses;d) plant design not allowing testwork results to be achieved;e) operating deficiencies."

Jan 1, 1982

By Louis Cabot

A pilot plant of the Modular Gold Processing Unit (MGPU) was designed, installed and operated, over a 8 months period, by RSW-Béroma, at the Granada Mine located near Rouyn-Noranda, Quebec. A description of the project geology, plant set up as well as exploitation results, including productivity and profitability curves, are given for a small scale mining operation in comparison with larger ones. Copyright ã 2001 CIM

May 1, 2001

By C. Pawlik, R. T. Jones

Cobalt occurs together with copper in the southern African copper belt, and a large portion of this cobalt ends up in copper smelting slags, mostly dissolved in oxide form. It is possible to achieve high recoveries of cobalt by reductive smelting of the copper slags, using some form of carbon as a reducing agent in an electric furnace. For example, a 40 MW DC arc furnace was operated at Chambishi Metals in Zambia from 2001 to 2008, and demonstrated cobalt recoveries of around 80% from slag to an iron-rich alloy containing copper and cobalt. The alloy was atomized prior to leaching. With the recent increase in demand for cobalt (and the resulting high metal prices), there has been increasing interest in this process route. There is also an alternative hydrometallurgical process for recovering the valuable metals from the slag. The choice between these process options requires a trade-off between capital and operating cost and environmental acceptability. This paper examines the potential for cobalt recovery from slags, and outlines various process options. INTRODUCTION Cobalt has had a number of important uses in society since antiquity, and its principal use has changed dramatically over time. Since at least 2250 BC, cobalt-based pigments (cobalt blue) have been widely used to colour manufactured goods such as glass and pottery. Later, cobalt became known for its magnetic and wear-resistant properties and high-strength alloys, and most of the cobalt produced was consumed in the production of cobalt-based superalloys. The greatest recent growth in cobalt demand is due to it being essential to the rechargeable lithium-ion batteries used in consumer electronic devices and increasingly to drive electric vehicles. Cobalt is usually produced as a by-product of copper or nickel. The copper belt in the Democratic Republic of the Congo (DRC) and Zambia supplies most of the world's cobalt production. In 2018, the DRC was expected to produce 90 000 tons of the world total of 140 000 tons of cobalt (Shedd, 2019). This paper focuses on the southern African copper industry, and specifically the cobalt that is able to be produced as a co-product from this. A BRIEF HISTORY OF SOUTHERN AFRICAN COPPER SMELTING Copper deposits in South Africa have been documented since at least 1685, when the Cape governor, Simon van der Stel, ‘discovered’ the 'Copper Mountain' at Springbok. South Africa's first public commercial mining company (imaginatively called the 'South African Mining Company') was established in Cape Town in 1846, to exploit the rich copper resources that were believed to exist in Namaqualand.

Jan 1, 2019

By M. Coleman, M. E. Reed

The control of feed delivery quality to the flash furnace remains an unsolved problem. Many operations around the world still have limited control of feed quality to their flash furnace. Schenck Process and WorleyParsons continue to work towards the ‘holy grail’ of simple quality feed delivering both radial feed distribution and pulseless feed delivery. Ten years ago they joined forces to offer a system based on then Clyde Process RotoFeed system which could deliver ground level installation, online mixing of materials, pulseless feeding direct to the burner, with good radial distribution. Unfortunately, this proved to be too large a step for the Flash Smelting community and met with resistance from the process owners. Since then the community has developed a range of options some of which have been implemented over this period. Despite these improvements there are still areas of concern including safety issues associated with concentrate leaks and spills, uncontrolled variations in feed rate including massive flooding events, intermittent distribution improvement and set up of the burner continues to be trial and error and hard to repeat the success in each burner campaign. These continue to impact flash furnace performance globally on a daily basis. Following the community reticence to pursue the complete solution a number of interim steps are now available to pave the way to the ultimate feed system. The mixing of material has been installed and is delivering line blended materials on a daily basis. This paper will investigate the developments over the last 10 years and discuss the pros and cons of this incremental step process for overall furnace control. INTRODUCTION Schenck Process and WorleyParsons have continued to interact and observe changes in the flash smelting industry and to consider application of the Clyde RotoFeed now incorporated in the Schenck Process ProStreamTM range for delivery of feed directly to the concentrate or matte burner. Schenck Process pneumatic injection from the Clyde Process range, ProStreamTM, utilises two types of volumetric feeders to accurately control the feed of material into an injection pipeline. These are referred to as the RotoFeed and RotoScrew technologies and the choice of feeder type is dependent on the characteristics of the material to be handled. The RotoFeed is generally used for finer, granular and powdered materials which cannot be accurately handled with a screw such as pulverised coal and copper concentrate, whilst the RotoScrew is particularly suited to coarser lump materials, particularly abrasive of cohesive materials like zinc powder, electronic scrap and metal ashes. Both units can operate at high pressures and many systems work at 3 to 10 bar with the occasional system working at 20 or 30bar for carbon to gasifiers. For the Flash furnace the ProStreamTM units can be used to deliver each of the furnace feed materials into a single line, mixing the materials homogeneously and live to the burner.

Jan 1, 2019

By R. A. Gannicott

Trend surface analysis was used to investigate the geochemical dispersion patterns of Si, Ai, Fe, Mg, Ca, Na, K, Ti and Rb in the footwall of the Seneca massive sulphide prospect in southwestern British Columbia. Surfaces for various element ratios were also produced to see if the distributions of the elements are related to each other. Trends developed by the elements redistributed during hydrothermal alteration may be difficult to detect for various reasons, such as too few and widely separated sample points, random analytical errors or local variations in rock chemical composition that are not related to regional trends. Trend surface analysis is useful to distinguish regional trends from local fluctuations. The computer program used in this study is capable of calculating surfaces up to the 6th degree polynomial, but provides for automatic termination when the variables in the equation for successive surfaces become effectively collinear. With the relatively small number of data points used (21 samples) in this study, such termination occurred after the quadratic surface. Results show that, at the Seneca prospect, Mg and K increase, and Na and Ca decrease, toward a common centre which corresponds closely with the best drill-core intersections of ore. The centre is interpreted as a volcanic vent and as the source of mineralization . Quadratic surfaces for element ratios show that K/Ca decreases and Fe/Mg increases away from this vent. Thin-section and X-ray diffraction analyses indicate that these variations reflect sericitization of plagioclase and an increase in the Mg content of chlorite near the vent. The mineralization , rock types and element dispersion patterns at the Seneca prospect are similar to those reported for volcanogenic massive sulphide deposits at Bathurst, New Brunswick, and in the Hokuroko district of Japan.

Jan 1, 1979

By Arnold R. Pasieka, George V. Sotirow

"The object of this paper is to outline a computerized net cash flow approach for practical cutoff grade determinations. A cutoff grade carries not only geological but also economic value, in which costs are balanced against revenues. For different situations, cutoff grades are a 'standard of value' that are determined for the purpose of classifying economic or uneconomic mineral reserves in a specified time frame. In a constantly changing technical and economic environment, the decision to develop or maintain a mining operation at its best economic potential, requires an appropriate cutoff grade strategy, a strategy consistent with short- and long-term operational and corporate objectives and one based on realistic marketing and metal prices forecasts. The use of a project evaluation computer program, in combination with specific corporate net cash flow requirements, shows the most promising and flexible team approach for cutoff grade optimization.IntroductionThe recent recession has had a devastating effect on the Canadian mining industry. Exploration and mining R&D expenditures have been critically reduced and now are believed to be below healthy levels. Ore reserves, mine life and cutoff grades are careening in several directions because of low base metal prices, relatively high costs and sensitive precious metal prices.These conditions demand an improved understanding of the terms ""ore"" and ""cutoff grades"" as they are applied to the planning process and day-to-day operations. ""Ore"" or 'ore reserves"" is a dynamic concept, reflecting a cumulative effect of changes in geological, technical and economic conditions in terms of material which can be mined at a potential profit. By contrast, if economics are not the primary consideration, the term ""mineral reserve"" or ""mineral inventory"" should be used to describe the mineral deposit. For different situations, cutoff grade is ""a standard of value"" determined for the purpose of classifying mineral reserves as economic or uneconomic in a specified time frame. The question of mining at average reserve grade or low-grade material during high metal prices is of paramount importance for cutoff grade strategy."

Jan 1, 1985

By K. E. Waters, J. E. Nesset, F. Rosenblum, J. A. Finch, S. Moon

"Some materials when exposed to various conditions can exhibit a rise in temperature without requiring an external heat source. Generally referred to as pyrophoric or self-heating substances, they challenge the safety of materials handling, storage and transportation. Reliably assessing the self-heating potential of materials is thus essential. Over the years a number of test protocols have been developed. A widely accepted method is that recommended by the United Nations to certify the safety of shipping pyrophoric goods. Our test work on sulphide materials has shown that the U.N. test can give false negatives if the sample oxidation history is not considered. Depending on the degree of oxidation (“weathering”), the same sulphide material can exhibit self-heating ranging from safe to hazardous. For concentrates, oxidation can occur during storage and transport making the sample weathering history an important consideration in the test work. To make the U.N. test, and other single-stage self-heating procedures, more reliable in assessing self-heating potential when testing sulphide materials, it is suggested that a weathering step be incorporated in the test protocol. This test work for two sulphide samples, an ore and a concentrate, demonstrates the impact of incorporating a weathering stage in the test protocol. INTRODUCTIONSelf-heating occurs when exothermic reactions produce heat faster than can be dissipated to the surroundings. Numerous substances self-heat, ranging from wood chips and powdered milk to coal and sulphide minerals (Beever & Crowhurst, 1989; Hudak, 2002). Mixtures of sulphide minerals, most notably those containing the iron sulphide pyrrhotite (Fe(1-x)S), commonly encountered in the extraction of base metals (e.g., copper, zinc, lead, and nickel), are particularly prone to self-heating (Rosenblum, Nesset, & Spira, 2001; Payant, Rosenblum, Nesset, & Finch, 2012). In the mining and subsequent processing stages, the minerals are progressively liberated and finely ground, then separated, usually by flotation, with the resulting concentrates stored and transported to smelters for metal extraction. At most of these stages the sulphides are exposed to both moisture and oxygen, conditions that promote partial sulphide oxidation and the formation of elemental sulphur. Studies have shown that pyrrhotite, in particular, readily oxidizes to form elemental sulphur (Bernier & Li, 2003; Belzile, Chen, Cai, & Li, 2004; Somot & Finch, 2010). The elemental sulphur becomes fuel for further self-heating as the temperature of the mineral mixture increases above 100 oC (Rosenblum & Spira, 1995; Somot & Finch, 2010). It is believed the propensity of pyrrhotite to self-heat is a result of its iron-deficient, and hence somewhat unstable structure. It is worth noting that pure metal sulphides (with the exception of pyrrhotite) do not exhibit appreciable self-heating. A mixture of minerals sufficiently different in their electrochemical rest potential is required to initiate self-heating at ambient temperatures (Payant et al., 2012)."

Jan 1, 2016

By K. B. Culver

"This paper provides background information on the expansion programs of Rio Algom Limited at Elliot Lake. Included are details on the Quirke expansion program, the Panel mine rehabilitation program, including the selection procedure for the tailings containment area, the Stanleigh mine rehabilitation program, housing, government regulations and the Environmental Assessment Board hearings. Introduction After 2Y2 years of public hearings, 4 years of arbritrating differences of opinion between our engineers and government licencing authorities, interspersed with research into radium removal and development of the LAMIX process and carrying out the work associated with some 24 control orders issued to us by the MOE, it is very difficult to compress all of the experiences and frustrations into a single paper. The highlights, as they relate to the expansion programs of Rio Algorn Limited and its affiliate, Preston Mines Limited, will be covered. Denison Mines Limited, of course, is the other uranium producer in Elliot Lake. They are currently in the process of expanding from 7,000 to 11,000 TPD by the second half of 1980 and then to 15,000 TPD by the mid 1980's. In giving this overview, the following seven items will be discussed: • The basis for Rio Algom's and Preston's expansion plans. • The Quirke Expansion. • The Panel Rehabilitation. • The Stanleigh Rehabilitation. • Housing Programs. • Government Licencing Requirements. • Environmental Assessment Board Hearings."

Jan 1, 1980

The 2-4D window shown above is the base startup window which allows you to begin a new project. ??Setting up the project is the first step ??The next step is to setup the properties to be used in this project

Feb 1, 2008

By J. G. Henning, T. R. Yu, J. E. Croxall

"Test work was carried out to investigate the thermal response of loose and solid rock under varying environmental conditions. The primary interest was to develop a technique that could be used to increase the thermal variation between loose and solid rock for better detectability of loose rock underground with a thermal imaging infrared scanner.A variety of thermal enhancement methods were evaluated both in the laboratory and in the mine environment. Air temperature variation created by the exhaust from diesel driven, mobile mining machinery was studied in detail. When sufficient hot exhaust was supplied to the air, unsteady thermal conditions became more pronounced on the rock surf ace. This allowed a greater percentage of loose rock to be detected by a high-resolution infrared scanner within minutes.The degree of thermal enhancement of loose rock was found to be dependent directly on the thermal conductivity of rock, looseness, air temperature change, and inversely on the size of loose, airflow rate and distance downwind from the heat source. It was also found that an air temperature rise of at least r c, or rock temperature differential of1°C was necessary for minimal thermal enhancement required f or infrared detection."

Jan 1, 1990

By A. McIntyre, L. R. Plitt

Both the Bond and the Hardgrove grindability tests are widely used in the mineral industry to measure the ease of the comminution displayed by a material. The Hardgrove test is mainly used for coals, whereas the Bond grindabifity test is mainly applied to hardrock minerals. The Bond grindability has the advantage that it can be empirically related to the energy required for comminution (work index), whereas the Hardgrove grindabifity test has the advantage of being easier to perform. In an effort to establish a valid correlation between work index and Hardgrove grindability, a series of parallel grindability tests were carried out on a wide variety of rocks and minerals. The standard Hardgrove test was modified to allow for materials with a higher density than coal. A new, satisfactory relationship was established which permits rapid estimation of work index from Hardgrove test data.

Jan 1, 1980

By A. A. Ruitenberg, L. R. Fyffe

"This paper compares several distinct types of mineral deposits associated with different families of granitoid rocks in the New Brunswick Appalachians. Porphyry copper deposit s are associated with late-stage differentiates of Lower to Middle Devonian I-type igneous complexes. Contact metasomatic deposits were formed where these plutons intrude carbonate rocks and they gave rise to vein deposits in fracture zones near wrench faults. The I-type granitoids were emplaced mainly in areas of thin continental crust and locally along prominent faults in areas of thick continental crust.In contrast, tin-tungsten-molybdenum-bearing greisen deposits and skarns, and antimony-bearing quartz veins are associated with predominantly S-stype granitoid complexes ranging in age from Middle Devonian to early Carboniferous. The mineral deposits occur within or along the contacts of very fractionated (specialized) late phases of these intrusive complexes, which are characterized by high K2O/Na2O, Rb/Sr and Rb/Ba, and low Fe, Mg, Zr and Ti contents. These specialized granitoids are in a large wrench fault zone that cuts across thick continental crust in southwestern and central New Brunswick.IntroductionA great variety of igneous intrusions and subvolcanic stocks were emplaced in the New Brunswick Appalachians during the latter stages of and immediately after the Acadian Orogeny (late Lower to Middle Devonian) and during the subsequent Hercynian Orogeny (Carboniferous). The presence or absence and characteristics of mineral deposits associated with these intrusions reflect the level of intrusion, the composition of the associated igneous rocks and the composition of the invaded sequences.Nickel-copper sulphide deposits occur in mafic intrusions in the St. Stephen area of the southwestern Magaguadavic - St. Croix Zone and in the Goodwin Lake area of the northeastern Mirarnichi Zone. Contact metasomatic and vein-type copper-rich base metal sulphide deposits and porphyry copper deposits with or without molybdenum are related mainly to high-level granitoid stocks of intermediate composition in the Matapedia-Tobique and northwest Miramichi zones. Tintungsten - molybdenum deposits with or without base metal sulphide minerals and antimony-uranium deposits are mainly associated with Upper Devonian and Lower Carboniferous biotite-muscovite granites and related 'subvolcanic intrusions that occur in an arc-shaped belt extending from the southwestern Magagaudavic - St. Croix Zone into the central Mirarnichi Zone."

Jan 1, 1982

By A. Chieregato, C. G. Oñate Salazar, D. Martinelli, D. Peila, M. Barbero

This paper is aimed to confirm the possibility to excavate fractured rock masses by using EPB shields, even in presence of relevant water tables. This verification is based on laboratory test experiences carried out at TUSC laboratory of Politecnico di Torino, where the natural material is tested in order to verify the suitability of a certain conditioning technique in particular conditions. This is due to the fact that every case should be studied apart from existing studies on a certain rock type, as other factors such as fragmentation of the rock mass, natural water content and porosity of the rock can considerably influence the final result of the conditioning process. The most important aspects that allow to consider the conditioning of fractured rock masses as suitable are: possibility to create a plastic paste that can transmit the pressure at the front in a effective way; reduce the permeability of the spoil material in order to reduce the possibility of water leakage inside the chamber and eventually in the tunnel; verify the consistency of the conditioned material for the extraction through the screw conveyors and the belt conveyors. For this research an argillitic schistose rock mass, with some quartzitic and calcareous inclusions, has been studied by using different level of conditioning in order to verify the suitability of an eventual EPB excavation through this formation.

Jan 1, 2015

By E. Busse, J. E. Burgener, J. G. Eacott, M. C. Robinson, P. E. Burgener

"This paper presents a preliminary assessment of the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from electric arc furnace baghouse dust at a mini-steelplant. Recent studies and literature are referenced briefly as they pertain to the formation and characterization of dust, toxicity considerations and alternative dust treatment and disposal options.Laboratory testwork results, published data, pilot plant experience and anticipated influences resulting from recycling residues are used for the purpose of developing a conceptual design for a caustic leach - electrowinning plant to treat 15,000 tonnes/year of dust at a one million tonnes /year capacity steelplant in Canada.Target economic studies, comprising preliminary estimates of capital and operating costs, revenues and rate of return are presented. Economic and commercial considerations concerning the relative merits of dust treatment at a centralized facility compared with an on-site plant are discussed.IntroductionThe treatment or disposal of mini-steelplant electric arc furnace (EAF) baghouse dust has been given increasing attention in recent years for two principal reasons. Firstly, the dust is now classed as a hazardous waste material under V.S. EPA regulations which prohibit its disposal in dumps other than controlled landfill sites. Secondly, the dust contains certain metal values, notably zinc and lead, which may be economically recoverable, depending on the costs associated with disposal resulting from enforcement of the EPA regulations. Other metallurgical dusts and waste materials, from both ferrous and non-ferrous operations, may require the same considerations as EAF baghouse dust.Several studies have been carried out to examine various aspects of dust treatment but few commercial plants are in operation. Technology employed uses pyrometallurgical techniques. Commercial-scale hydrometallurgical plants are not known to exist although small-scale plants are frequently more economically attractive than their pyrometallurgical counterparts which generally require economies of scale to be viable.The concentration of mini-steelplants in northeast V.S.A. and southeast Canada merits study to determine whether or not dust treatment for metals recovery is a commercially feasible alternative to disposal.This paper examines the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from EAF baghouse dust at an on-site ministeel plant processing carbon steel scrap and discusses economic and commercial considerations pertaining to dust treatment at a larger, centralized facility."

Jan 1, 1984